Displayport Connector; Ethernet Connector (Tps And Lan Ports); Dc Connection; Analog Stereo Audio - Lightware HDMI-TPS-TX210 User Manual


  
3. Product Overview
3.3.3. DisplayPort Connector
DP-TPS-TX210/TX220 and SW-TPS-TX240
provide standard 20-pole DisplayPort connector for input.
Always use high quality DP cable for connecting DisplayPort devices.
3.3.4. Ethernet Connector (TPS and LAN Ports)
The extender provides standard RJ45 connectors for TPS IN and
LAN ports. Always use high quality Ethernet cable for connecting
transmitters and receivers. Maximum CATx cable distances can be
found in the Maximum Extension Distances
8 1
LAN connector
Wiring of TPS and LAN Cables
Lightware recommends the termination of LAN cables on the basis of
TIA/EIA T 568 A or TIA/EIA T 568 B standards.
8
1
Top Bottom
Pin TIA/EIA T568 A Color and name TIA/EIA T568 B Color and name
1 white/green stripe
2 green solid
3 white/orange stripe
4 blue solid
5 white/blue stripe
6 orange solid
white/brown stripe
7
8 brown solid
Pin assignments of RJ45 connector types
You can find more information about TPS interface in the
section.
3.3.5. 12V DC Connection
models
section.
The transmitters are built with locking 12V DC connector. Do not
forget to turn the plug clockwise direction before disconnecting the
1 8
power adaptor.
WARNING! Always use the supplied 12V power adaptor. Warranty
void if damage occurs due to use of a different power source.
TPS connector
3.3.6. Analog Stereo Audio
The connector is used for receiving unbalanced analog audio
signal. It is also known as (3.5 mm or approx. 1/8") audio jack,
phone jack, phone plug and mini-jack plug.
1
1 2 3
8
Side
white/orange stripe
You can find more information about audio functions in the
orange solid
Interface
white/green stripe
blue solid
white/blue stripe
green solid
white/brown stripe
brown solid
TPS Interface
HDMI-TPS-TX200 series – User's Manual
P I
P I
N :
N :
2 . 1 2 . 1
m m
m m
1 2 1 2
V V
1 A D 1 A D C
C
Locking DC connector
Pin nr. Signal
1 Left
2 Right
3 Ground
Jack audio plug pin assignments
section.
3.3.7. RS-232 Connector
The extender contains a 3-pole Phoenix connector which is
used for RS-232 serial connection.
Pin nr.
1
1 2 3
2
3
RS-232 connector pin assignments
Compatible Plug Type
Phoenix Combicon series (3.5mm pitch, 3-pole), type: MC 1.5/3-ST-3.5.
®
You can find more information about RS-232 interface in the
Interface section.
3.3.8. IR Connector
IR detector and IR emitter can be connected to the
HDMI-TPS-TX100 series extenders with TRS (Tip, Ring, and
Sleeve) connectors. They are also known as (3,5 mm or approx.
1/8") audio jack, phone jack, phone plug, and mini-jack plug. The pin
assignments are the following for the detector and the emitter:
1 2 3
Detector – 3-pole-TRS
1 Tip IR Input -
2 Ring GND
Audio
3 Sleeve IR Input +
INFO: Ring pole of the emitter is optional. If your IR emitter has
three pole-TRS plug, then the Ring and the Sleeve are the same
signal (Output - ).
You can find more information about Infrared interface in the
Interface section.
14
Signal
Ground
TX data
RX data
Serial
1 2
Emitter – 2-pole-TS
1 Tip IR Output +
2 Ring IR Output -
3 Sleeve IR Output -
IR