Query The Status Of Destination Port; Query The Video Crosspoint Setting; Switching Video Input; Query The Video Autoselect Settings - Lightware HDMI-TPS-TX210 User Manual


  
7. LW3 Programmer's Reference
7.6.2. Query the Status of Destination Port
Command format: GET●/MEDIA/VIDEO/XP.DestinationPortStatus
Response format: pr●/MEDIA/VIDEO/XP.DestinationPortStatus=[<O
The response contains 5 ASCII characters for each port. The first character indicates the mute/lock state,
the next 2-byte long HEX code showing the current state of the output ports.
Example:
˃ GET /MEDIA/VIDEO/XP.DestinationPortStatus
˂ pr /MEDIA/VIDEO/XP.DestinationPortStatus=M00BF;T00EF
Legend: See at previous section.
Example and Explanation (for output 1, M00BF):
M 0
0 0 0 0 0 0
Unlocked,
Muted
Reserved Reserved Reserved
7.6.3. Query the Video Crosspoint Setting
Command format: GET●/MEDIA/VIDEO/XP.DestinationConnectionList
Response format: pr●/MEDIA/VIDEO/XP.DestinationConnectionList=<I
Legend:
<I >:
n
Example:
˃ GET /MEDIA/VIDEO/XP.DestinationConnectionList
˂ pr /MEDIA/VIDEO/XP.DestinationConnectionList=I1
Explanation: I1 input port is connected to the output port.
7.6.4. Switching Video Input
Command format: CALL●/MEDIA/VIDEO/XP:switch(<I
Response format: mO●/MEDIA/VIDEO/XP:switch
Example:
˃ CALL /MEDIA/VIDEO/XP:switch(I2:O1)
˂ mO /MEDIA/VIDEO/XP:switch
Explanation: I2 port is connected to O1 port.
>]
n
0 B
0 0 1 0 1 1 1 1
No embedded Signal
Reserved Encrypted
audio presents
>
n
Video input port number
>:<O >)
n m
HDMI-TPS-TX200 series – User's Manual
7.6.5. Query the Video Autoselect Settings
Command format:
Response format:
The response shows the settings of each output one by one.
Legend:
Letter
1 letter
st
2 letter
nd
F
1 1
Example:
Connected
˃ GET /MEDIA/VIDEO/XP.DestinationPortAutoselect
˂ pr /MEDIA/VIDEO/XP.DestinationPortAutoselect=EL
Explanation:
EL: the Autoselect is Enabled on output, selected mode is Last detect.
INFO: For more information about the Autoselect feature see
7.6.6. Change the Autoselect Mode
Command format: CALL●/MEDIA/VIDEO/XP:setDestinationPortAutoselect(<O
Response format: mO●/MEDIA/VIDEO/XP.setDestinationPortAutoselect
Legend: see previous section.
Example1:
˃ CALL /MEDIA/VIDEO/XP:setDestinationPortAutoselect(O1:EPM)
˂ mO /MEDIA/VIDEO/XP:setDestinationPortAutoselect
Explanation1: The setting is changed to "EPM": Autoselect is enabled (E); the mode is set to "priority detect"
(P), and the port will be disconnected if a higher priority port becomes active (M).
Example2:
˃ CALL /MEDIA/VIDEO/XP:setDestinationPortAutoselect(O1:D)
˂ mO /MEDIA/VIDEO/XP:setDestinationPortAutoselect
Explanation2: The setting is changed to "DPM": Autoselect is disabled (D). The other settings remain
unchanged. Since the outputs are linked, the change will affect local and link out.
GET●/MEDIA/VIDEO/XP.DestinationPortAutoselect
pr●/MEDIA/VIDEO/XP.DestinationPortAutoselect=<O
< O _set> Two-letter code of the Autoselect settings:
n
Explanation
E: Autoselect is enabled.
D: Autoselect is disabled.
F: First detect mode: the first active video input is selected.
P: Priority detect mode: always the highest priority active video input will be selected.
L: Last detect mode: always the last attached input is switched to the output automatically.
58
_set>
n
The Autoselect Feature section.
>:<O _set>)
n n