Batco 2035 Assembly Manual page 123

PORTABLE GRAIN BELT CONVEYOR – STANDARD
3. Place the electric offset clamp (11) on the tube and line it up with the mounting brackets welded onto the
tube. Secure to the brackets with bolts (2) and 1/2" x 1-1/2" nylock nuts (4). Lift the offset clamp support
top (17) and attach to the bottom of the electric offset clamp (11) with 1/2" x 1-1/2" bolts (1), 1/2" washers
(14), and 1/2" nylock nuts (4). Do not tighten.
4. Attach the electric mount adjuster (9) to the electric offset clamp (11) with 1/2" x 1-1/2" carriage bolts (5)
and 1/2" nylock nuts (4). Do not tighten.
5. Install set screw (6) on the electric offset clamp.
6. Take the motor mount plate (10) and line up the tube with the hinge holes on the electric offset clamp (11)
and electric mount adjuster (9) and insert the electric mount pin (8). Place a 3/4" washer (15) on the electric
mount adjuster side and secure in place with a 1/4" x 2" cotter pin (7). Ensure that the motor mount plate is
level before tightening all fasteners (3, 18).
7. Mount arm (20) on s-drive with a 1/2" x 1-1/2" bolt (1) and 1/2" nut (12).
8. In breather kit (26), install the vent and plug on the back side of the gearbox. Install the plug towards the
bottom of the gearbox and install the vent towards the top of the gearbox.
9. Install 3/8" x 1/2" x 6-1/2" key (33) on drive roller shaft and attach the gearbox (27) to the shaft with
1/2" x 2-1/2" bolts (19), 1/2" lock washer (13), and end cap (23).
10. Prevent the gearbox from rotating by attaching it to the arm (20) with a 1/2" x 6" bolt (34) and 1/2" nut
(12).
11. Install adjuster rods (24) to the black plate mount bar using two 1/2" nuts (12). This will hold the rods
straight, allowing you to mount the remaining components.
12. Affix back plate (28) to gearbox and mount clamp (11) using 1/2" x 17" adjuster rods (24), 1/2" washers (14)
and 1/2" nuts (12). Ensure the back plate is level and tight against the gearbox. Install 1/2" x 13" adjuster
rod (32) to gearbox and back plate.
13. Attach electric motor to mount plate (10).
14. Install pulleys/bushing (21, 29, 30) on gearbox (27) and the electric motor with 3/8" x 2" key (22). Ensure all
pulleys are lined up.
15. Mount metal guard (35) over belts/pulleys, securing with 1/2" flat washers (14) and 1/2" nylock nuts (4).
16. Install the pulley guard back plate (36) to the metal guard (35) using 1/4" x 1" self-tapping screws (37).
Table 54. Electric Drive (2400 Series) Components
ITEM
1
Bolt Hex 1/2" x 1-1/2" GR8
2
Bolt Tap 1/2" x 2-1/2"
3
Bolt Tap 3/4" x 7"
4
Nut Nylock 1/2"
5
Carriage Bolt 1/2" x 1-1/2"
6
Sq HD Setscrew 7/16" x 2-1/2"
7
Cotter Pin 1/4" x 2"
8
HD Electric Mount Pin
9
Electric Mount Adjuster
10
20 Series Motor Mount Plate
P1512021 R6
DESCRIPTION
QTY
9
4
1
15
2
1
1
1
1
1
4. ASSEMBLY
123