Hach BioTector B7000 User Manual page 96

10. - 15. Stm Alarm 1-6 (if configured in the system). This allows the user to test the function of the Stream
Alarms if they are programmed in Output Devices menu. To change the state of the device, press the
ENTER key, set the device to ON/OFF, and press the ENTER key again. If the device is on, it will be
marked with an "*".
16. Sample Fault 1 (if configured in the system). Use this function to test the Sample Fault 1 output signal.
To change the state of the device, press the ENTER key, set the device to ON/OFF, and press the
ENTER key again. If the device is on, it will be marked with an "*".See Output Devices section for details.
17. Sync Relay (if configured in the system). Use this function to test the Synchronization relay. To change
the state of the device, press the ENTER key, set the device to ON/OFF, and press the ENTER key
again. If the device is on, it will be marked with an "*". See Output Devices section for details.
18. Sample Status (if configured in the system). Use this function to test the Sample Status output. To
change the state of the device, press the ENTER key, set the device to ON/OFF, and press the ENTER
key again. If the device is on, it will be marked with an "*". See Output Devices section for details.
19. Cal Signal (if configured in the system). Use this function to test the Calibration Signal output. To
change the state of the device, press the ENTER key, set the device to ON/OFF, and press the ENTER
key again. If the device is on, it will be marked with an "*". See Output Devices section for details.
20. Maint Signal (if configured in the system). Use this function to test the Maintenance Signal output. To
change the state of the device, press the ENTER key, set the device to ON/OFF, and press the ENTER
key again. If the device is on, it will be marked with an "*". See Output Devices section for details.
21. Stop (if configured in the system). Use this function to test the Stop output. To change the state of the
device, press the enter key, set the device to ON/OFF, and press the ENTER key again. If the device is
on, it will be marked with an "*". See Output Devices section for details.
22-24. Fault, Fault or Warning, Warning (if configured in the system). Use these functions to test the
Fault and Warning outputs. To change the state of the device, press the ENTER key, set the device to
ON/OFF, and press the ENTER key again. If the device is on, it will be marked with an "*". See Output
Devices section for details.
25. Note (if configured in the system). Use this function to test the system Notification output. To change
the state of the device, press the ENTER key, set the device to ON/OFF, and press the ENTER key
again. If the device is on, it will be marked with an "*". See Output Devices section for details.
26. Man Mode Trig (if configured in the system). Use this function to test system Manual Mode Trigger
output. To change the state of the device, press the ENTER key, set the device to ON/OFF, and press
the ENTER key again. If the device is on, it will be marked with an "*". See Output Devices section for
details.
27-33. 4-20mA Chng 1-6 (if configured in the system). Use these functions to test system 4-20mA Change
outputs for single stream or for specific streams from Stream 1 to Stream 6. To change the state of the
device, press the ENTER key, set the device to ON/OFF, and press the ENTER key again. If the device is
on, it will be marked with an "*". See Output Devices section for details.
34. 4-20mA Read (if configured in the system). Use this function to test system 4-20mA Read output. To
change the state of the device, press the ENTER key, set the device to ON/OFF, and press the ENTER
key again. If the device is on, it will be marked with an "*". See Output Devices section for details.
36.  Input/Output Status. Input/Output Status is a link to Maintenance, Diagnostics, Input/Output Status
menu.
Page 96