Yamaha CL5 Reference Manual page 274

◆ DISTDELAY
One input, two output distortion and delay effects in series.
Parameter Range
DST1, DST2, OVD1,
DST TYPE Distortion type (DST = distortion, OVD = overdrive)
OVD2, CRUNCH
DRIVE 0-100 Distortion drive
MASTER 0-100 Master volume
TONE -10 to +10 Tone control
N. GATE 0-20 Noise reduction
SYNC OFF/ON Tempo parameter sync on/off
*1
DLY.NOTE Used in conjunction with TEMPO to determine DELAY
*2
MOD.NOTE Used in conjunction with TEMPO to determine FREQ
DELAY 0.0-2725.0 ms Delay time
Feedback gain (plus values for normal-phase feedback, minus values for
FB. GAIN -99 to +99%
reverse-phase feedback)
HI. RATIO 0.1-1.0 High-frequency feedback ratio
FREQ. 0.05-40.00 Hz Modulation speed
DEPTH 0-100% Modulation depth
Distortion and delay balance
DLY.BAL 0-100%
(0% = all distortion, 100% = all delayed distortion)
*1.
setting)
*2.
◆ MULTI FILTER
Two input, two output 3-band multi-filter (24 dB/octave).
Parameter Range
TYPE 1 LPF, HPF, BPF Filter 1 type: high pass, low pass, band pass
FREQ. 1 28.0 Hz-16.0 kHz Filter 1 frequency
LEVEL 1 0-100 Filter 1 level
RESO. 1 0-20 Filter 1 resonance
TYPE 2 LPF, HPF, BPF Filter 2 type: high pass, low pass, band pass
FREQ. 2 28.0 Hz-16.0 kHz Filter 2 frequency
LEVEL 2 0-100 Filter 2 level
RESO. 2 0-20 Filter 2 resonance
TYPE 3 LPF, HPF, BPF Filter 3 type: high pass, low pass, band pass
FREQ. 3 28.0 Hz-16.0 kHz Filter 3 frequency
LEVEL 3 0-100 Filter 3 level
RESO. 3 0-20 Filter 3 resonance
Description
(Maximum value depends on the tempo
Description
17
◆ FREEZE
One input, two output basic sampler.
Parameter Range
In MANUAL mode, recording is started by pressing the REC and PLAY
REC MODE MANUAL, INPUT buttons. In INPUT mode, Record-Ready mode is engaged by pressing the
REC button, and actual recording is triggered by the input signal.
Recording delay.
REC DLY -1000 to +1000 ms For plus values, recording starts after the trigger is received. For minus
values, recording starts before the trigger is received.
In MOMENT mode, the sample plays only while the PLAY button is
MOMENT, CONTI., pressed. In CONT mode, playback continues once the PLAY button has
PLY MODE
been pressed. The number of times the sample plays is set using the LOOP
INPUT
NUM parameter. In INPUT mode, playback is triggered by the input signal.
Input trigger level (i.e., the signal level required to trigger recording or
TRG LVL -60 to 0 dB
playback)
Once playback has been triggered, subsequent triggers are ignored for the
TRG MASK 0-1000 ms
duration of the TRG MASK time.
*1
START Playback start point in milliseconds
END *1 Playback end point in milliseconds
LOOP *1 Loop start point in milliseconds
LOOP
0-100 Number of times the sample plays
NUM
PITCH -12 to +12 semitones Playback pitch shift
FINE -50 to +50 cents Playback pitch shift fine
MIDI TRG OFF, C1-C6, ALL The PLAY button can be triggered by using MIDI Note on/off messages.
START
0-131000 Playback start point in samples
[SAMPLE]
END
0-131000 Playback end point in samples
[SAMPLE]
LOOP
0-131000 Loop start point in samples
[SAMPLE]
*1. 0.0-5941.0 ms (fs=44.1 kHz), 0.0 ms-5458.3 ms (fs=48 kHz)
One input, two output distortion effect.
Parameter Range
DST1, DST2, OVD1,
DST TYPE Distortion type (DST = distortion, OVD = overdrive)
OVD2, CRUNCH
DRIVE 0-100 Distortion drive
MASTER 0-100 Master volume
TONE -10 to +10 Tone control
N. GATE 0-20 Noise reduction
Description
◆ DISTORTION
Description
Data List