Yamaha CL5 Reference Manual page 205

FUNCTION PARAMETER 1 PARAMETER 2
MIX1-MIX24
MTRX 1-MTRX 8
MIX ON FADER
SENDS ON
NORMAL/WITH CUE
MATRIX ON FADER
FADER
SENDS ON FADER
+48V
Ø
INSERT ON
DIRECT OUT ON
SET BY SEL PRE SEND -
TO STEREO
TO MONO
TO LCR
GAIN COMPENSATION
SET DEFAULT
- -
VALUE
SET NOMI-
- -
NAL VALUE
L ON
R ON
C ON
SURROUND
*5)
PAN
LFE ON
Ls ON
Rs ON
PANNING L
PANNING R
PANNING Front Center
*5)
PANNING Ls
SURROUND
PANNING Rs
PAN
PANNING Back
PANNING Side L
PANNING Side R *5)
PANNING Center
Description
This function switches between the normal
function on/off (NORMAL), and the function
with cue on/off (WITH CUE). With the WITH
CUE option, cue will be enabled if SENDS ON
FADER mode is engaged or if you switch mode
during SENDS ON FADER mode. Also, with the
WITH CUE option, cue for all output channels
will be canceled if SENDS ON FADER mode is
disengaged.
Hold down this key and press SEL to switch it
on/off.
During this time, the [SEL] LED will be lit if on or
dark if off.
If SET [PRE SEND] is selected, "SEND ON
FADER" mode is engaged while you are holding
down the [SEL] key.
It goes OFF when the bank is switched.
Press and hold this key, and then press any of
the following knobs on the panel to reset that
knob to its default value: a knob in the
SELECTED CHANNEL section, a knob in the
SELECTED CHANNEL VIEW screen, or a knob in
the Centralogic section.
It goes OFF when the bank is switched.
While holding down this key, press a [SEL] key
to set the fader of that channel to nominal level.
You can also push a knob in the SEND field of
the SELECTED CHANNEL VIEW screen to set the
send level to nominal level.
It goes OFF when the bank is switched.
In Surround mode, this is used to switch the bus
assign on and off for the channel selected in list
5).
In Surround mode, this is used to set hard
panning for the channel selected in list 5).
In Surround mode, this is used to set hard
panning for the channel selected in list 5).
202
FUNCTION PARAMETER 1 PARAMETER 2
SURROUND
PANNING TOGGLE *5)
PAN
LATCH
TALKBACK ON
UNLATCH
SELECTED CH ASSIGN -
TALKBACK
DIRECT ASSIGN *3)
DIRECT ASSIGN WITH
TALKBACK *3)
ON
CURRENT PAGE -
WITH POPUP
TAP TEMPO
EFFECT RACK1-8
WITHOUT POPUP
Setup
Description
In Surround mode, this is used to toggle the
settings for hard panning for the channel
selected in list 5).
With each press, the setting is toggled in the
following order: Center L Front Center R
Side R Rs Back, Ls Side L (Center).
Switch TALKBACK on/off.
Turn TALKBACK on while pressed.
It goes OFF when the bank is switched.
While holding down this key, press a SEL key of
an OUTPUT channel to switch the assignment
on/off. During this time, the [SEL] LED will be lit
if assign is ON, or dark if OFF.
The assignment setting made while holding
down this key will be stored. Pressing the key
again will recall the stored setting. Settings can
be stored in multiple keys to facilitate rapid
assignment switching.
It goes OFF when the bank is switched.
The operations performed when this key is
pressed are as follows.
- Toggle assignment of channel selected in list
3) ON and OFF.
At this time, the LED display is as shown below.
- If the channel is assigned, the LED will be on.
Otherwise, the LED will be off.
The operations performed when this key is
pressed are as follows.
- Assignments other than for the channel
selected in list 3) are removed.
- If a channel is assigned and TALKBACK is ON
at the same time, TALKBACK is turned OFF
and the channel assignment is removed.
- Otherwise, TALKBACK will be ON and the
channel assignment will be ON.
At this time, the LED display is as shown below.
- If the channel is assigned and TALKBACK is ON
at the same time, the LED will be on.
- Otherwise, the LED will be off.
Use the tap tempo function in the displayed
screen.
Use the tap tempo function for the specified
effect. If WITH POPUP is selected, the Tap
Tempo screen is displayed. If WITHOUT POPUP
is selected, the Tap Tempo screen is not
displayed.
Reference Manual