HP 6127XLG Blade Switch Series
FCoE
Part number: 797693-001
Software version: Release 2418P03
Document version: 6W100-20150806

Advertising

   Also See for HP 6127XLG Blade Series

   Related Manuals for HP 6127XLG Blade Series

   Summary of Contents for HP 6127XLG Blade Series

  • Page 1: Command Reference

    HP 6127XLG Blade Switch Series FCoE Command Reference Part number: 797693-001 Software version: Release 2418P03 Document version: 6W100-20150806...

  • Page 2

    The only warranties for HP products and services are set forth in the express warranty statements accompanying such products and services. Nothing herein should be construed as constituting an additional warranty.

  • Page 3: Table Of Contents

    Contents FCoE commands ·························································································································································· 1   FCoE mode commands ····················································································································································· 1   display fcoe-mode ···················································································································································· 1   fcoe-mode ·································································································································································· 1   VFC interface commands ················································································································································· 3   bandwidth ································································································································································· 3   bind interface ···························································································································································· 3   default ········································································································································································ 6   description ·································································································································································...

  • Page 4: Table Of Contents

    priority ···································································································································································· 44   rscn aggregation enable ······································································································································ 44   rscn aggregation timer ·········································································································································· 45   snmp-agent trap enable fc-fabric ························································································································· 46   snmp-agent trap enable fc-name-service ············································································································· 47   timer distributed-services ······································································································································· 48   timer error-detect···················································································································································· 48   timer resource-allocation ······································································································································· 49  ...

  • Page 5: Table Of Contents

    ···································································································································································· 127   FC tracert commands ··················································································································································· 129   fctracert ································································································································································· 129   Support and other resources ·································································································································· 131   Contacting HP ······························································································································································ 131   Subscription service ············································································································································ 131   Related information ······················································································································································ 131   Documents ···························································································································································· 131  ...

  • Page 6: Fcoe Commands

    FCoE commands FCoE mode commands display fcoe-mode Use display fcoe-mode to display the FCoE mode of the switch. Syntax display fcoe-mode Views Any view Predefined user roles network-admin network-operator Examples # Display the FCoE mode of the switch. <Sysname> display fcoe-mode The FCoE mode is NONE.

  • Page 7

    Default A switch operates in non-FCoE mode. Views System view Predefined user roles network-admin Parameters fcf: Specifies the FCF mode. fcf-npv: Specifies the FCF-NPV mode. npv: Specifies the NPV mode. transit: Specifies the Transit mode. Usage guidelines An FC and FCoE-capable switch can operate in non-FCoE mode or in one of the following FCoE modes: •...

  • Page 8: Vfc Interface Commands

    Related commands display fcoe-mode VFC interface commands bandwidth Use bandwidth to set the expected bandwidth for an interface. Use undo bandwidth to restore the default. Syntax bandwidth bandwidth-value undo bandwidth Default The expected bandwidth (in kbps) is the interface baud rate divided by 1000. Views VFC interface view Predefined user roles...

  • Page 9

    Default A VFC interface is not bound to any Ethernet interface. Views VFC interface view Predefined user roles network-admin Parameters interface-type interface-number: Specifies an interface by its type and number. The interface type can only be one of the following: Layer 2 Ethernet interface.

  • Page 10

    When you bind a VFC interface to an S-channel interface or S-channel aggregate interface, follow these restrictions and guidelines: To successfully bind a VFC interface to an S-channel interface or S-channel aggregate interface, • make sure the switch is operating in expert mode. For information about system operating modes, see Fundamentals Configuration Guide.

  • Page 11: Default

    default Use default to restore the default settings for a VFC interface. Syntax default Views VFC interface view Predefined user roles network-admin Usage guidelines CAUTION: The default command might interrupt ongoing network services. Make sure you are fully aware of the impacts of this command when you execute it on a live network.

  • Page 12: Display Interface Vfc

    Parameters text: Specifies an interface description, a case-sensitive string of 1 to 255 characters. Usage guidelines The description helps users identify the role of an interface. Examples # Set the description to Vfcport1 for interface VFC 1. <Sysname> system-view [Sysname] interface vfc 1 [Sysname-Vfc1] description Vfcport1 Related commands display interface vfc...

  • Page 13

    Current state: UP Line protocol state: UP Description: Vfc1 Interface Bandwidth: 10000000kbps Maximum Transmit Unit: 2112 Internet protocol processing: disabled Link layer protocol is FC Port WWN is 66:66:66:63:66:64:61:30 FC mode is E, state is E Support the VSAN protocol VSAN tagging mode is Tagging EVFP common VSAN: 1 Bound interface is FortyGigE1/1/1, Bound MAC is 000c-2933-eacd...

  • Page 14

    Brief information on VFC interface(s): Admin Mode: auto - auto; E - e port; F - f port; NP - n port proxy Oper Mode: E - e port; F - f port; NP - n port proxy; TE - trunking e port; TF - trunking f port; TNP - trunking n port proxy Interface Admin Admin Oper Status Bind...

  • Page 15: Fc Mode (vfc Interface View)

    <Sysname> display interface vfc brief down Brief information on interface(s) under bridge mode: Link: ADM - administratively down; Stby - standby Interface Link Cause Vfc1 Administratively Table 5 Command output Field Description Brief information on interface(s) Brief information about Layer 2 interfaces. under bridge mode Link status: •...

  • Page 16: Interface Vfc

    Parameters e: Specifies the E mode. f: Specifies the F mode. np: Specifies the NP mode. Usage guidelines An FCF switch supports E and F modes. An NPV switch supports F and NP modes. An FCF-NPV switch supports E, F, and NP modes. On an FCF-NPV switch, if the mode of a VFC interface is not supported by a VSAN of the interface, the mode does not take effect in the VSAN.

  • Page 17: Reset Counters Interface

    Related commands display interface vfc reset counters interface Use reset counters interface to clear the statistics for VFC interfaces. Syntax reset counters interface [ vfc [ number ] ] Views User view Predefined user roles network-admin Parameters number: Specifies a VFC interface by its number in the range of 1 to 1024. Usage guidelines Clear the existing statistics before collecting traffic statistics within a specific period of time on an interface.

  • Page 18

    Predefined user roles network-admin Examples # Bring up interface VFC 1. <Sysname> system-view [Sysname] interface vfc 1 [Sysname-Vfc1] undo shutdown FCoE commands display fcoe Use display fcoe to display global FCoE configuration. Syntax display fcoe Views Any view Predefined user roles network-admin network-operator Usage guidelines...

  • Page 19: Display Fcoe Vlan

    fcoe fka-adv-period • • fcoe global fcf-priority display fcoe vlan Use display fcoe vlan to display the FCoE configuration of a VLAN. Syntax display fcoe vlan vlan-id Views Any view Predefined user roles network-admin network-operator Parameters vlan vlan-id: Specifies a VLAN by its ID in the range of 1 to 4094. Usage guidelines Only FCF-NPV switches support this command.

  • Page 20: Fcoe Enable

    fcoe enable Use fcoe enable to enable FCoE in a VLAN and map the VLAN to a VSAN. Use undo fcoe enable to disable FCoE in a VLAN. Syntax fcoe enable [ vsan vsan-id ] undo fcoe enable Default FCoE is disabled in a VLAN. Views VLAN view Predefined user roles...

  • Page 21: Fcoe Fcmap

    Syntax fcoe fcf-priority priority undo fcoe fcf-priority Default The FCF priority of a VFC interface is 128. Views VFC interface view Predefined user roles network-admin Parameters priority: Specifies the FCF priority for the VFC interface, in the range of 0 to 255. The smaller the value, the higher the priority.

  • Page 22: Fcoe Fka-adv-period

    Usage guidelines On FCF or NPV switches, you can set an FC-MAP value only in system view. On FCF-NPV switches, you can set an FC-MAP value only in VLAN view. An FC-MAP value identifies an FCoE network. Switches in the same FCoE network must have the same FC-MAP value.

  • Page 23

    The switch sends unsolicited Discovery Advertisements every FKA advertisement interval out of its VFC interfaces in E mode. The FKA advertisement interval value is carried in unsolicited Discovery Advertisements. After receiving an unsolicited Discovery Advertisement, the peer switch maintains the status of the virtual link and records the FKA advertisement interval value.

  • Page 24: Fcoe Global Fcf-priority

    [Sysname-vlan2] fcoe fka-adv-period 20 fcoe global fcf-priority Use fcoe global fcf-priority to set the system FCF priority. Use undo fcoe global fcf-priority to restore the default. Syntax fcoe global fcf-priority priority undo fcoe global fcf-priority Default The system FCF priority is 128. Views System view, VLAN view Predefined user roles...

  • Page 25: Display Vsan Status

    Syntax display vsan [ vsan-id ] port-member Views Any view Predefined user roles network-admin network-operator Parameters vsan-id: Specifies a VSAN by its ID in the range of 1 to 3839. If you do not specify this argument, this command displays the member interfaces of each VSAN. Examples # Display the member interfaces of each VSAN.

  • Page 26: Port Trunk Vsan

    1 to 3839. The value for vsan-id2 must be greater than or equal to the value for vsan-id1. Usage guidelines HP recommends not including both FCF-mode VSANs and NPV-mode VSANs on an FCF-NPV switch in a VSAN list. If you do so, the following events occur during trunk mode negotiation: An E_Port selects only FCF-mode VSANs.

  • Page 27: Vsan

    An NP_Port selects only NPV-mode VSANs. • Examples # Assign interface VFC 1 to VSANs 1, 2, 10, and 20 through 100. <Sysname> system-view [Sysname] interface vfc 1 [Sysname-Vfc1] port trunk vsan 1 to 2 10 20 to 100 vsan Use vsan to create a VSAN and enter VSAN view.

  • Page 28: Working-mode

    Examples # Create VSAN 10 and enter its view. <Sysname> system-view [Sysname] vsan 10 [Sysname-vsan10] # Change the name of VSAN 10 from its default to FCF-VSAN. <Sysname> system-view [Sysname] vsan 10 name FCF-VSAN [Sysname-vsan10] # Create VSAN 1 1 with a name of FCF-VSAN, and enter the view of VSAN 1 1. <Sysname>...

  • Page 29: Fabric Setup Commands

    A VSAN operating in FCF mode acts as an FCF switch. A VSAN operating in NPV mode acts as an NPV switch. If the configured mode of an interface is not supported by a VSAN of the interface, the mode does not take effect in the VSAN.

  • Page 30: Display Fc Domain

    Otherwise, the non-principal switch refuses the assigned domain ID and isolates its interface connected to the principal switch. HP recommends that you configure the same allowed domain ID list on all switches in a VSAN. Examples # Configure VSAN 1 to allow domains 3 through 10.

  • Page 31

    Priority: 2 Domain ID: 100 Configuration information: Domain configure: Enabled Domain auto-reconfigure: Disabled Fabric name: 41:6e:64:69:61:6d:6f:21 Priority: 128 Domain ID: 100 (static) Principal switch running time information: Priority: 2 Path Interface Downstream Vfc1 Downstream Vfc2 Downstream Vfc4 Table 10 Command output Field Description Running status:...

  • Page 32: Display Fc Domain-list

    Field Description Interface Local VFC interface. display fc domain-list Use display fc domain-list to display the list of domain IDs dynamically assigned in VSANs. Syntax display fc domain-list [ vsan vsan-id ] Views Any view Predefined user roles network-admin network-operator Parameters vsan vsan-id: Specifies a VSAN by its ID in the range of 1 to 3839.

  • Page 33: Display Fc Ess

    Related commands domain configure enable display fc ess Use display fc ess to display the Exchange Switch Support (ESS) negotiation result, including the following information: • The capabilities of the local switch after the ESS negotiation. The capabilities of the remote switch after the ESS negotiation. •...

  • Page 34: Display Fc Login

    Table 12 Command output Field Description Domain Domain ID of the switch. Directory Server Capability List of directory server capabilities. Indicates whether the switch supports accepting large name server objects (yes for supported and no for not supported). Accept large name server objects A large name server object contains the symbolic name of the N_Port and the symbolic name of the node in addition to the information of a small name server object.

  • Page 35: Display Fc Name-service Database

    Usage guidelines Only FCF and FCF-NPV switches support this command. Examples # Display the node login information of VSAN 1. <Sysname> display fc login vsan 1 Interface VSAN FCID Node WWN Port WWN Vfc1 0x010000 21:01:00:1b:32:a0:fa:18 21:01:00:1b:32:a0:fa:17 # Display the number of logged-in nodes for VSAN 1. <Sysname>...

  • Page 36

    Parameters vsan vsan-id: Specifies a VSAN by its ID in the range of 1 to 3839. If you do not specify a VSAN, this command displays the name server database information of all VSANs. On an FCF-NPV switch, this command displays the name server database information of only VSANs operating in FCF mode. fcid fcid: Specifies an FC address.

  • Page 37

    Port-type: 0x01(N) Fabric-port-WWN: 30:30:30:30:65:33:64:6 Hard-addr: 0x000000 VSAN:1 FCID: 0x030200 Port-WWN(vendor): 20:00:00:5a:c9:28:c7:01 Node-WWN: 10:00:00:5a:c9:28:c7:01 Class: 3 Node-IP-addr: 192.168.6.171 FC4-types(FC4_features): NPV Symbolic-port-name: NPV-Sysname:Vfc1 Symbolic-node-name: NPV-Sysname Port-type: 0x01(N) Fabric-port-WWN: 22:0a:00:05:30:00:26:1e Hard-addr: 0x000000 --- Total 2 entries --- Table 15 Command output Field Description FCID FC address of the N_Port.

  • Page 38: Display Fc Scr-table

    Symbolic name, which is used for describing an N_Port. For an Symbolic-port-name NP_Port on an HP NPV switch, it is in the form of system-name:port-name. Symbolic name, which is used for describing a node. For an HP NPV Symbolic-node-name switch, it is the system-name. Port-type Link type of the N_Port, which can be N representing point-to-point.

  • Page 39: Display Fc Switch-wwn

    Table 16 Command output Field Description SCR table for VSAN SCR list in a VSAN. FCID FC address of the N_Port. Type of Registered State Change Notification (RSCN) messages: • fabric detected rscns—Accepts all RSCN messages sent by the switches in the fabric.

  • Page 40: Domain Auto-reconfigure Enable

    resource-allocation: Specifies the resource allocation timeout period, in milliseconds. vsan vsan-id: Specifies a VSAN by its ID in the range of 1 to 3839. If you do not specify a VSAN, this command displays global fabric timer information. Usage guidelines If you do not specify the distributed-services, error-detect, or resource-allocation keyword, this command displays all fabric timers.

  • Page 41: Domain Configure Enable

    [Sysname] vsan 1 [Sysname-vsan1] domain auto-reconfigure enable Related commands domain configure enable domain configure enable Use domain configure enable to enable the fabric configuration feature in a VSAN. Use undo domain configure enable to disable the fabric configuration feature in a VSAN. Syntax domain configure enable undo domain configure enable...

  • Page 42: Domain-id

    Parameters disruptive: Initiates a disruptive reconfiguration. If you do not specify this keyword, this command initiates a non-disruptive reconfiguration. Usage guidelines Only FCF switches and VSANs operating in FCF mode support this command. This command takes effect only when the fabric configuration feature is enabled. A fabric reconfiguration triggers a principal switch selection phase.

  • Page 43: Fabric-name

    If a non-principal switch fails to get the configured static-type domain ID, it does not accept any • other domain ID and isolates the upstream principal link. HP recommends that you set domain IDs of the same type for all switches in the same VSAN. Examples # Specify static-type domain ID 55 in VSAN 1.

  • Page 44: Fc Domain Rcf-reject

    Parameters name: Specifies a fabric name, in the format of xx:xx:xx:xx:xx:xx:xx:xx, where x is a hexadecimal number. Usage guidelines Only FCF switches and VSANs operating in FCF mode support this command. An FCF switch supports assigning a fabric name to each VSAN, in the same format as the WWN (a 64-bit address).

  • Page 45: Fc Name-service Auto-discovery

    [Sysname-Vfc1] fc domain rcf-reject vsan 1 fc name-service auto-discovery Use fc name-service auto-discovery to enable SCSI-FCP information autodiscovery. Use undo fc name-service auto-discovery to disable SCSI-FCP information autodiscovery. Syntax fc name-service auto-discovery undo fc name-service auto-discovery Default SCSI-FCP information autodiscovery is enabled. Views VSAN view Predefined user roles...

  • Page 46: Fc Timer Error-detect

    Default The global distributed service timeout period is 5000 milliseconds. Views System view Predefined user roles network-admin Parameters value: Specifies the distributed service timeout period in the range of 5000 to 10000 milliseconds. Usage guidelines The distributed service timeout period can be set in system view or VSAN view. The setting in system view takes effect on all VSANs.

  • Page 47: Fc Timer Resource-allocation

    The setting in system view takes effect on all VSANs. The setting in VSAN view takes effect only on the current VSAN. If you set the error detection timeout period both globally and for a VSAN, the setting for the VSAN takes precedence.

  • Page 48: Fc Wwn Default-fc4-type

    fc wwn default-fc4-type Use fc wwn default-fc4-type to configure the default FC4 information for a node. Use undo fc wwn default-fc4-type to delete the default FC4 information of a node. Syntax fc wwn wwn-value default-fc4-type { type-value feature feature-map | scsi-fcp feature { feature-map | both | initiator | target } } undo fc wwn wwn-value default-fc4-type { type-value | scsi-fcp } Default...

  • Page 49: Priority

    Examples # Configure the default FC4 information for the node with WWN 00:00:00:1 1:22:33:44:55. <Sysname> system-view [Sysname] fc wwn 00:00:00:11:22:33:44:55 default-fc4-type scsi-fcp feature target [Sysname] fc wwn 00:00:00:11:22:33:44:55 default-fc4-type 9 feature 7 priority Use priority to set the switch priority in a VSAN. Use undo priority to restore the default.

  • Page 50: Rscn Aggregation Timer

    FC addressees of multiple nodes with changes in a single RSCN. This feature reduces the number of RSCNs sent to the concerned registered nodes. HP recommends that you enable RSCN aggregation and set the same RSCN aggregation timer value on all switches in a VSAN.

  • Page 51: Snmp-agent Trap Enable Fc-fabric

    Only FCF switches and VSANs operating in FCF mode support this command. The RSCN aggregation timer takes effect only when RSCN aggregation is enabled. HP recommends that you enable RSCN aggregation and set the same RSCN aggregation timer value on all switches in a VSAN.

  • Page 52: Snmp-agent Trap Enable Fc-name-service

    Examples # Enable SNMP notifications for domain ID changes. <Sysname> system-view [Sysname] snmp-agent trap enable fc-fabric domain-id-change # Enable SNMP notifications for fabric changes. <Sysname> system-view [Sysname] snmp-agent trap enable fc fabric-change snmp-agent trap enable fc-name-service Use snmp-agent trap enable fc-name-service to enable SNMP notifications for the name service module. Use undo snmp-agent trap enable fc-name-service to disable SNMP notifications for the name service module.

  • Page 53: Timer Distributed-services

    timer distributed-services Use timer distributed-services to set the distributed service timeout period for a VSAN. Use undo timer distributed-services to restore the default. Syntax timer distributed-services value undo timer distributed-services Default The distributed service timeout period is 5000 milliseconds. Views VSAN view Predefined user roles network-admin...

  • Page 54: Timer Resource-allocation

    Views VSAN view Predefined user roles network-admin Parameters value: Specifies the error detection timeout period in the range of 1000 to 10000 milliseconds. Usage guidelines The error detection timeout period can be set in system view or VSAN view. The setting in system view takes effect on all VSANs. The setting in VSAN view takes effect only on the current VSAN.

  • Page 55: Wwn Area-port-id

    If you set the resource allocation timeout period both globally and for a VSAN, the setting for the VSAN takes precedence. Examples # Set the resource allocation timeout period to 6000 milliseconds for VSAN 1. <Sysname> system-view [Sysname] vsan 1 [Sysname-vsan1] timer resource-allocation 6000 Related commands fc timer resource-allocation...

  • Page 56: Fc Routing And Forwarding Commands

    [Sysname-vsan1] wwn 33:e8:00:05:30:00:16:df area-port-id ab12 FC routing and forwarding commands display fc exchange Use display fc exchange to display the FC exchange entries. Syntax display fc exchange { link | protocol } [ slot slot-number ] display fc exchange link verbose [ slot slot-number [ exid exid ] ] Views Any view Predefined user roles...

  • Page 57

    <Sysname> display fc exchange link slot 2 Local_ID:EXID Remote_ID:EXID State Slot Protocol 0x060501:1024 0x010001:1025 ESTABLISHED 2 # Display detailed information about the link exchange entries. <Sysname> display fc exchange link verbose slot 1 slot: 1 protocol: 8 connection info: Local = 0x090801:1155 , Remote = 0x050001:1089 PCB flags: 0x2 FC Class: FC_CLASS_F...

  • Page 58: Display Fc Fib

    display fc fib Use display fc fib to display the FC FIB entries. Syntax display fc fib [ fcid [ mask-length ] ] vsan vsan-id Views Any view Predefined user roles network-admin network-operator Parameters fcid: Specifies a destination FC address in the range of 0x000000 to 0xFFFFFF (hexadecimal). mask-length: Specifies the mask length for the destination address, in the range of 0 to 24.

  • Page 59: Display Fc Routing-table

    Destination count: 1 FIB entry count: 1 Destination/Mask Interface 0x030100/24 Vfc3 # Display the FC FIB entries for the specified FC address and mask length. <Sysname> display fc fib 030100 16 vsan 18 FC FIB information in VSAN 18: Destination count: 1 FIB entry count: 2 Destination/Mask Interface...

  • Page 60

    mask-length: Specifies the mask length for the FC address. This argument is used together with the fcid argument. The value of this argument can be 8, 16, or 24. If you do not specify the mask length, this command displays the routing information for the FC address fcid with masks 8, 16, and 24. statistics: Displays the statistics for the FC routing table.

  • Page 61

    Destination/mask: 0xfffffa/24 Protocol: DIRECT Preference: 0 Cost: 0 Interface: InLoop0 State: Active Age: 0h21m36s Destination/mask: 0xfffffc/24 Protocol: DIRECT Preference: 0 Cost: 0 Interface: InLoop0 State: Active Age: 0h21m36s Destination/mask: 0xfffffd/24 Protocol: DIRECT Preference: 0 Cost: 0 Interface: InLoop0 State: Active Age: 0h21m36s Table 19 Command output Field...

  • Page 62: Display Fspf Graceful-restart

    Table 20 Command output Field Description Protocol type: • DIRECT—Direct routes. Protocol • STATIC—Static routes. • FSPF—FSPF routes. route Number of routes of the specified protocol type. active Number of active routes of the specified protocol type. added Number of added routes of the specified protocol type. deleted Number of deleted routes of the specified protocol type.

  • Page 63: Display Fspf Lsdb

    Graceful-restart period : 120 seconds FSPF graceful restart information of VSAN 1: Number of neighbors under helper : 0 Number of restarting neighbors FSPF graceful restart information of VSAN 2: Number of neighbors under helper : 0 Number of restarting neighbors Table 21 Command output Field Description...

  • Page 64: Display Fspf Neighbor

    Examples # Display FSPF LSDB information. <Sysname> display fspf lsdb FSPF LSDB information of VSAN 1(01): Total LSR count: 2 FSPF Link State Database for Domain 01 LSR Type LSR Age LSR Incarnation number : 0x80000008 LSR Checksum : 0x7deb Number of links NbrDomainID IfIndex...

  • Page 65

    Syntax display fspf neighbor [ vsan vsan-id ] Views Any view Predefined user roles network-admin network-operator Parameters vsan vsan-id: Specifies a VSAN by its ID in the range of 1 to 3839. If you do not specify a VSAN, this command displays information about all FSPF neighbors.

  • Page 66: Display Fspf Statistics

    Field Description Neighbor state: • Down—The neighbor does not start negotiation. • Init—The neighbor has started negotiation. • State DB_Exchange—The neighbor has been discovered. • DB_Wait—The local switch has sent the LSR. • DB_Ack_Wait—The neighbor has sent the LSR. • Full—Synchronization is complete.

  • Page 67: Fc Route-static

    Interface Vfc1 statistics: Type Input Output HELLO Table 24 Command output Field Description FSPF statistics for a VSAN. The value in parentheses is the domain ID in decimal FSPF statistics of VSAN of the local switch. SPF computing count Number of SPF calculations. Interface statistics Packet statistics on the interface.

  • Page 68: Fspf Cost

    Parameters fcid: Specifies the destination FC address of the static FC route, in the range of 0x010000 to 0xFFFFFF (hexadecimal). mask: Specifies a hexadecimal mask for the FC address. This argument is used together with the fcid argument. The value of this argument can be 0xFF0000, 0xFFFF00, or 0xFFFFFF. mask-length: Specifies the mask length for the FC address.

  • Page 69: Fspf Dead-interval

    Parameters value: Specifies the FSPF cost in the range of 1 to 65535. vsan vsan-id: Specifies a VSAN by its ID in the range of 1 to 3839. Usage guidelines Only FCF and FCF-NPV switches support this command. Each link has a cost. The route selection algorithm uses this value to determine the best route. The smaller the interface FSPF cost, the smaller the link cost.

  • Page 70: Fspf Enable

    [Sysname-Vfc1] fspf dead-interval 100 vsan 4 Related commands fspf hello-interval fspf enable Use fspf enable to enable FSPF in a VSAN. Use undo fspf enable to disable FSPF in a VSAN. Syntax fspf enable undo fspf enable Default FSPF is enabled after a VSAN is created. Views VSAN view Predefined user roles...

  • Page 71: Fspf Graceful-restart Helper

    Usage guidelines Only FCF and FCF-NPV switches support this command. FSPF Graceful Restart (GR) ensures nonstop forwarding of traffic by backing up FSPF configuration information during a protocol restart (for example, the FSPF process restart triggered by the process command) or active/standby switchover. GR involves the following roles: •...

  • Page 72: Fspf Graceful-restart Interval

    fspf graceful-restart • fspf graceful-restart interval Use fspf graceful-restart interval to set the maximum FSPF GR interval. Use undo fspf graceful-restart interval to restore the default. Syntax fspf graceful-restart interval interval-value undo fspf graceful-restart interval Default The maximum FSPF GR interval is 120 seconds. Views System view Predefined user roles...

  • Page 73: Fspf Min-ls-arrival

    Predefined user roles network-admin Parameters value: Specifies the hello interval in the range of 1 to 65534 seconds. vsan vsan-id: Specifies a VSAN by its ID in the range of 1 to 3839. Usage guidelines Only FCF and FCF-NPV switches support this command. The hello interval specifies the time between the hello packets sent periodically by the switch to discover and maintain neighbor relationships.

  • Page 74: Fspf Min-ls-interval

    Examples # Set the minimum LSR arrival interval for VSAN 2 to 10 seconds. <Sysname> system-view [Sysname] vsan 2 [Sysname-vsan2] fspf min-ls-arrival 10 fspf min-ls-interval Use fspf min-ls-interval to set the minimum LSR refresh interval for a VSAN. Use undo fspf min-ls-interval to restore the default. Syntax fspf min-ls-interval value undo fspf min-ls-interval...

  • Page 75: Fspf Silent

    Default The LSR retransmission interval is 5 seconds. Views VFC interface view Predefined user roles network-admin Parameters value: Specifies the LSR retransmission interval of the interface in seconds, in the range of 1 to 65535. vsan vsan-id: Specifies a VSAN by its ID in the range of 1 to 3839. Usage guidelines Only FCF and FCF-NPV switches support this command.

  • Page 76: Fspf Spf-hold-time

    Examples # Disable FSPF for interface VFC 1 in VSAN 4. <Sysname> system-view [Sysname] interface vfc 1 [Sysname-Vfc1] fspf silent vsan 4 fspf spf-hold-time Use fspf spf-hold-time to set the shortest SPF calculation interval in a VSAN. Use undo fspf spf-hold-time to restore the default. Syntax fspf spf-hold-time value undo fspf spf-hold-time...

  • Page 77: Fc Zone Commands

    Views User view Predefined user roles network-admin Parameters vsan vsan-id: Specifies a VSAN by its ID in the range of 1 to 3839. If you do not specify a VSAN, this command clears the FSPF statistics for all VSANs. Usage guidelines Only FCF and FCF-NPV switches support this command.

  • Page 78: Display Zone

    display zone Use display zone to display zone information. Syntax display zone [ [ name zone-name ] vsan vsan-id ] Views Any view Predefined user roles network-admin network-operator Parameters name zone-name: Specifies a zone name, a case-sensitive string of 1 to 64 characters. A zone name can contain English letters (uppercase and lowercase), numbers, and special characters dollar sign ($), minus sign (-), caret (^), and underscore (_), and it must start with an English letter.

  • Page 79: Display Zone Member

    Field Description fwwn fWWN of the zone member. initiator Role of a zone member. If no role is indicated, the member has both roles. target Related commands member (zone view) • zone clone • zone name • • zone rename display zone member Use display zone member to display parent information for a zone member.

  • Page 80

    Zones and zone aliases to which the specified zone member belongs. • • Zones to which the zone aliases belong. VSANs to which the zones and zone aliases belong. • If a zone alias is not assigned to any zones, only the parent VSANs are displayed for the zone alias. Examples # Display parent information for zone member with FC address as 010000 in VSAN 1.

  • Page 81: Display Zone Statistics

    Table 26 Command output Field Description fcid FC address of the zone member for which parent information is displayed. pwwn pWWN of the zone member for which parent information is displayed. fwwn fWWN of the zone member for which parent information is displayed. Related commands member (zone view) •...

  • Page 82: Display Zone Status

    Field Description Change Request Number of Distribution Request packets. Change Accept Number of Distribution Accept packets. Change Reject Number of Distribution Reject packets. Related commands reset zone statistics display zone status Use display zone status to display the zoning configuration and status. Syntax display zone status [ vsan vsan-id ] Views...

  • Page 83: Display Zone-alias

    Mode: enhanced Default zone: permit Hard-zoning: enabled Full zoning database: Zonesets: 10, Zones: 20, Zone-aliases: 0 Status: distributing Table 28 Command output Field Description Mode Zone mode: basic or enhanced. Default zone policy: • Default zone deny—Deny members in the default zone from accessing each other. •...

  • Page 84

    Predefined user roles network-admin network-operator Parameters name zone-alias-name: Specifies a zone alias name, a case-sensitive string of 1 to 64 characters. A zone alias name can contain English letters (uppercase and lowercase), numbers, and special characters dollar sign ($), minus sign (-), caret (^), and underscore (_), and it must start with an English letter. vsan vsan-id: Specifies a VSAN by its ID in the range of 1 to 3839.

  • Page 85: Display Zoneset

    display zoneset Use display zoneset to display zone set information. Syntax display zoneset [ [ name zoneset-name ] vsan vsan-id ] Views Any view Predefined user roles network-admin network-operator Parameters name zoneset-name: Specifies a zone set name, a case-sensitive string of 1 to 64 characters. A zone set name can contain English letters (uppercase and lowercase), numbers, and special characters dollar sign ($), minus sign (-), caret (^), and underscore (_), and it must start with an English letter.

  • Page 86: Display Zoneset Active

    Table 30 Command output Field Description fcid FC address of a zone member. pwwn pWWN of a zone member. Related commands member (zone set view) • • zoneset clone zoneset name • zoneset rename • display zoneset active Use display zoneset active to display information about the active zone set. Syntax display zoneset active [ vsan vsan-id ] Views...

  • Page 87

    For a zone member that does not exist in the local name service database, only the configuration • content is displayed. Zone members cannot be displayed by zone alias in the active zone set. If a zone in the activated •...

  • Page 88: Member (zone View)

    *fcid 0x333333 [pwwn 33:33:33:33:33:33:33:33] zone name #default_zone# *fcid 0x20abcd *fcid 0xabcdef Table 31 Command output Field Description FC address of the zone member that can be queried from the local name *fcid service database. FC address of the zone member that does not exist in the local name service fcid database.

  • Page 89: Member (zone Alias View)

    zone-alias zone-alias-name: Specifies an existing zone alias, a case-sensitive string of 1 to 64 characters. A zone alias name can contain English letters (uppercase and lowercase), numbers, and special characters dollar sign ($), minus sign (-), caret (^), and underscore (_), and it must start with an English letter.

  • Page 90

    Syntax member { fcid fcid | fwwn fwwn | pwwn pwwn } [ initiator | target ] undo member { fcid fcid | fwwn fwwn | pwwn pwwn } Default No member exists in a new zone alias. Views Zone alias view Predefined user roles network-admin Parameters...

  • Page 91: Member (zone Set View)

    # Add an F_Port with fWWN 08:07:06:05:04:03:02:01 to zone alias za1 as both an initiator and a target. [Sysname-vsan2-zone-alias-za1] member fwwn 08:07:06:05:04:03:02:01 Related commands display zone-alias • • zone-alias name member (zone set view) Use member to add a zone to a zone set. Use undo member to remove a zone from a zone set.

  • Page 92: Pairwise-zoning Enable

    pairwise-zoning enable Use pairwise-zoning enable to enable the Pairwise feature for a zone. Use undo pairwise-zoning enable to disable the Pairwise feature for a zone. Syntax pairwise-zoning enable undo pairwise-zoning enable Default The Pairwise feature is disabled for a zone. Views Zone view Predefined user roles...

  • Page 93: Reset Zone Statistics

    member (zone alias view) • • zoneset activate zoneset distribute • reset zone statistics Use reset zone statistics to clear zone packet statistics. Syntax reset zone statistics [ vsan vsan-id ] Views User view Predefined user roles network-admin Parameters vsan vsan-id: Specifies a VSAN by its ID in the range of 1 to 3839. If you do not specify a VSAN, this command clears zone packet statistics for all VSANs.

  • Page 94: Zone Clone

    Parameters activation-completed: Enables SNMP notifications for zone set activation or deactivation. defaultzone-change: Enables SNMP notifications for default zone policy changes. hardzone-change: Enables SNMP notifications for hard zoning status changes. merge-failed: Enables SNMP notifications for merge failures. merge-succeeded: Enables SNMP notifications for merge successes. Usage guidelines Only FCF and FCF-NPV switches support this command.

  • Page 95: Zone Default-zone Permit

    [Sysname] vsan 1 [Sysname-vsan1] zone name z1 [Sysname-vsan1-zone-z1] quit # Create zone z2 by copying z1. [Sysname-vsan1] zone clone z1 z2 Related commands display zone • zone name • zone default-zone permit Use zone default-zone permit to allow members in the default zone to access each other. Use zone default-zone permit to deny members in the default zone from accessing each other.

  • Page 96: Zone Hard-zoning Enable

    zoneset distribute • zone hard-zoning enable Use zone hard-zoning enable to enable hard zoning in a VSAN. Use undo zone hard-zoning enable to disable hard zoning in a VSAN. Syntax zone hard-zoning enable undo zone hard-zoning enable Default Hard zoning is enabled in a VSAN. Views VSAN view Predefined user roles...

  • Page 97: Zone Merge-control Restrict

    zone merge-control restrict Use zone merge-control restrict to set the merge control mode to Restrict in a VSAN. Use undo zone merge-control restrict to restore the default. Syntax zone merge-control restrict undo zone merge-control restrict Default The merge control mode is Allow. Views VSAN view Predefined user roles...

  • Page 98: Zone Name

    Syntax zone mode enhanced undo zone mode enhanced Default The basic zoning mode is enabled in a VSAN. Views VSAN view Predefined user roles network-admin Usage guidelines Only FCF switches and VSANs operating in FCF mode support this command. A zoning mode switchover causes a zone distribution to ensure zoning mode consistency across the fabric.

  • Page 99: Zone Rename

    Predefined user roles network-admin Parameters zone-name: Specifies a zone name, a case-sensitive string of 1 to 64 characters. A zone name can contain English letters (uppercase and lowercase), numbers, and special characters dollar sign ($), minus sign (-), caret (^), and underscore (_), and it must start with an English letter. Usage guidelines Only FCF switches and VSANs operating in FCF mode support this command.

  • Page 100: Zone-alias Clone

    # Rename zone z1 as z2. [Sysname-vsan1] zone rename z1 z2 Related commands display zone • zone name • zone-alias clone Use zone-alias clone to create a zone alias by copying an existing zone alias. Syntax zone-alias clone src-name dest-name Views VSAN view Predefined user roles...

  • Page 101: Zone-alias Rename

    Use undo zone-alias name to delete a zone alias. Syntax zone-alias name zone-alias-name undo zone-alias name zone-alias-name Views VSAN view Predefined user roles network-admin Parameters zone-alias-name: Specifies the zone alias name, a case-sensitive string of 1 to 64 characters. A zone alias name can contain English letters (uppercase and lowercase), numbers, and special characters dollar sign ($), minus sign (-), caret (^), and underscore (_), and it must start with an English letter.

  • Page 102: Zoneset Activate

    Usage guidelines Only FCF switches and VSANs operating in FCF mode support this command. Examples # Create zone alias za1. <Sysname> system-view [Sysname] vsan 1 [Sysname-vsan1] zone-alias name za1 [Sysname-vsan1-zone-alias-za1] quit # Rename zone alias za1 as za2. [Sysname-vsan1] zone-alias rename za1 za2 Related commands display zone-alias •...

  • Page 103: Zoneset Clone

    Examples # Create zone z1. <Sysname> system-view [Sysname] vsan 1 [Sysname-vsan1] zone name z1 # Add an N_Port with the FC address as 010000 to zone z1. [Sysname-vsan1-zone-z1] member fcid 010000 [Sysname-vsan1-zone-z1] quit # Create zone set zs1. [Sysname-vsan1] zoneset name zs1 # Add zone z1 to zone set zs1.

  • Page 104: Zoneset Distribute

    <Sysname> system-view [Sysname] vsan 1 [Sysname-vsan1] zoneset name zs1 [Sysname-vsan1-zoneset-zs1] quit # Create zone set zs1 by copying zone set zs2. [Sysname-vsan1] zoneset clone zs1 zs2 Related commands • display zoneset zoneset name • zoneset distribute Use zoneset distribute to trigger a complete distribution, distributing both the active zone set and zone database.

  • Page 105: Zoneset Name

    Default The zone distribution and merge type is incomplete. Views VSAN view Predefined user roles network-admin Usage guidelines Only FCF switches and VSANs operating in FCF mode support this command. This command can be configured only in basic zoning mode. In enhanced zoning mode, the zone distribution and merge type is always complete, and this command is not supported.

  • Page 106: Zoneset Rename

    Usage guidelines Only FCF switches and VSANs operating in FCF mode support this command. Examples # Create zone set zs1 and enter its view. <Sysname> system-view [Sysname] vsan 1 [Sysname-vsan1] zoneset name zs1 [Sysname-vsan1-zoneset-zs1] Related commands display zoneset zoneset rename Use zoneset rename to rename a zone set.

  • Page 107: Npv Commands

    NPV commands display npv login Use display npv login to display the nodes on downlink interfaces and their mapped uplink interfaces. Syntax display npv login [ vsan vsan-id ] [ interface interface-type interface-number ] display npv login [ vsan vsan-id ] count Views Any view Predefined user roles...

  • Page 108: Display Npv Status

    Table 32 Command output Field Description Name of the downlink interface. Server Interface External interface Name of the uplink interface mapped by the downlink interface. FCID FC address of the node. Port WWN Port WWN of the node connected to the NPV switch. Entries Number of logged-in nodes for a VSAN.

  • Page 109

    Server Interfaces: Interface: Vfc5 VSAN tagging mode: Tagging VSAN State Down Number of Server Interfaces: 1 # Display the status information of interfaces in all VSANs. <Sysname> display npv status External Interfaces: Interface: Vfc1 VSAN tagging mode: Tagging VSAN State FCID 0x010003 Interface: Vfc2...

  • Page 110: Display Npv Traffic-map

    Field Description After an uplink interface goes up, the FC ID allocated by the core switch is displayed. A downlink interface does not have an FC ID. If an NPV switch is connected to two fabrics and its two uplink interfaces are assigned the same FC ID in a VSAN, one uplink interface can be up, but it cannot work as an uplink interface.

  • Page 111: Npv Auto-load-balance-interval

    Use undo npv auto-load-balance enable to disable automatic load balancing in a VSAN. Syntax npv auto-load-balance enable undo npv auto-load-balance enable Default Automatic load balancing is disabled. Views VSAN view Predefined user roles network-admin Usage guidelines Only NPV switches and VSANs operating in NPV mode support this command. The automatic load-balancing process is as follows: The system starts a delay timer when it detects a new operational uplink interface.

  • Page 112: Npv Load-balance Disruptive

    Predefined user roles network-admin Parameters interval: Specifies a value for the delay timer, in the range of 1 to 300 seconds. Usage guidelines Only NPV switches and VSANs operating in NPV mode support this command. The delay timer helps reduce network flapping caused by up/down events of uplink interfaces. If the link layer state of uplink interfaces is stable, set the delay timer to a smaller value.

  • Page 113: Npv Traffic-map

    npv traffic-map Use npv traffic-map to configure an uplink-to-downlink interface mapping. Use undo npv traffic-map to delete a configured uplink-to-downlink interface mapping. Syntax npv traffic-map server-interface interface-type interface-number external-interface interface-type interface-number undo npv traffic-map server-interface interface-type interface-number external-interface interface-type interface-number Default No uplink-to-downlink interface mapping is configured.

  • Page 114: Display Fip-snooping Fcf

    Views Any view Predefined user roles network-admin network-operator Parameters vlan vlan-id: Specifies a VLAN by its ID in the range of 1 to 4094. If you do not specify a VLAN, this command displays ENode information for all VLANs. Examples # Display ENode information obtained by the Transit switch.

  • Page 115: Display Fip-snooping Flushing-rules

    Table 35 Command output Field Description Interface Ethernet interface connecting the Transit switch to the FCF switch. FCF MAC FCoE MAC address of the FCF switch. ENode Number of ENodes attached to an FCF switch. display fip-snooping flushing-rules Use display fip-snooping flushing-rules to display the FIP snooping rules that are being flushed. Syntax display fip-snooping flushing-rules [ enode | fcf ] [ vlan vlan-id ] Views...

  • Page 116: Display Fip-snooping Rules

    FGE1/1/3 0000-1234-2212/48 0efc-0034-2111/24 Table 36 Command output Field Description Interface Ethernet interface on the Transit switch. Related commands display fip-snooping rules display fip-snooping rules Use display fip-snooping rules to display the FIP snooping rules that have been flushed. Syntax display fip-snooping rules [ enode | fcf ] [ vlan vlan-id ] [ slot slot-number ] Views Any view Predefined user roles...

  • Page 117: Display Fip-snooping Sessions

    TGE1/0/2 0efc-0034-0102/48 0000-1234-0201/48 ffffffff VLAN 4: FCF rules information: Interface Source MAC/Mask Destination MAC/Mask Context FGE1/1/3 0000-1234-1202/48 0efc-0034-1101/24 ffffffff Table 37 Command output Field Description Interface Ethernet interface on the Transit switch. Related commands display fip-snooping flushing-rules display fip-snooping sessions Use display fip-snooping sessions to display information about FIP snooping sessions (connections between ENodes and FCF switches).

  • Page 118: Fip-snooping Enable

    fip-snooping enable Use fip-snooping enable to enable FIP snooping in a VLAN. Use undo fip-snooping enable to disable FIP snooping in a VLAN. Syntax fip-snooping enable undo fip-snooping enable Default FIP snooping is disabled. Views VLAN view Predefined user roles network-admin Usage guidelines To enable a VLAN on a Transit switch to process FCoE frames and FIP frames, enable FIP snooping in the...

  • Page 119: Fip-snooping Port-mode

    Usage guidelines You can use the fcoe fcmap command to set the FC-MAP value in frames sent out of an FCF switch. You can use the fip-snooping fc-map command to set an FC-MAP value for a VLAN on a Transit switch. When an Ethernet interface in the FIP snooping VLAN receives a frame from the FCF switch, the following rules apply: If the FC-MAP value in the incoming frame is the same as the value set for the FIP snooping VLAN,...

  • Page 120: Fcs Commands

    <Sysname> system-view [Sysname] interface FortyGigE 1/1/2 [Sysname-FortyGigE1/1/2] fip-snooping port-mode fcf FCS commands fcs discovery start Use fcs discovery start to start a topology discovery in VSANs. Syntax fcs discovery start [ age interval ] vsan vsan-list Views System view Predefined user roles network-admin Parameters age interval: Specifies the aging time for the topology discovery information, in the range of 300 to...

  • Page 121: Display Fcs Discovery Status

    Predefined user roles network-admin Parameters vsan vsan-list: Specifies a VSAN by its ID or a range of VSANs in the form of vsan-id to vsan-id. The value range for the vsan-id argument is 1 to 3839. Usage guidelines Only FCF and FCF-NPV switches support this command. Examples # Stop the topology discovery in VSAN 1 through VSAN 100.

  • Page 122: Display Fcs Database

    : 0x01 Management address list : snmp://192.168.6.100 snmp://192.168.0.100 Fabric name : 10:01:00:11:22:00:01:01 Logical name : HP Information list : HP#HP 6127XLG Ethernet Blade Switch#Version 7.1.045, Release 2418P03 IE ports: Interface Port WWN Port type Attached port WWNs Vfc2 2f:15:01:11:22:00:01:01 F_Port...

  • Page 123: Display Fcs Ie

    Management address list : snmp://192.168.6.100 snmp://192.168.0.100 Fabric name : 10:00:00:11:22:00:01:01 Logical name : HP Information list : HP#HP 6127XLG Ethernet Blade Switch#Version 7.1.045, Release 2418P03 IE ports: Interface Port WWN Port type Attached port WWNs Table 39 Command output Field...

  • Page 124

    Syntax display fcs ie [ vsan vsan-id ] [ nwwn wwn ] [ verbose ] Views Any view Predefined user roles network-admin network-operator Parameters vsan vsan-id: Specifies a VSAN by its ID in the range of 1 to 3839. If you do not specify a VSAN, this command display the IE information in all VSANs.

  • Page 125

    Management address list: snmp://192.168.6.100 snmp://192.168.0.100 Information list Vendor name : HP Model name/number: HP 6127XLG Ethernet Blade Switch Release code : Version 7.1.045, Release 2418P03 # Display the detailed IE information in all VSANs. <Sysname> display fcs ie verbose IE List for VSAN 1:...

  • Page 126: Display Fcs Port

    Total 1 IEs in Fabric. Table 40 Command output Field Description The IE type can only be Switch. IE type Unknown is displayed for all other types. Name of the fabric where the IE resides. Fabric name Unknown indicates that the fabric name is not obtained from the IE. Device name of the IE.

  • Page 127

    Examples # Display the port information for all VSANs. <Sysname> display fcs port Port List for VSAN 1: IE WWN: 10:00:00:11:22:00:01:01 Port WWN Port type Tx type Module type 2f:15:01:11:22:00:01:01 Unknown Shortwave Laser SFP with Serial ID 38:00:00:11:22:00:01:01 E_Port Shortwave Laser SFP with Serial ID Total 2 switch-ports in IE.

  • Page 128

    Field Description Transmitter type of the port: • 10GBASE-CX4. • 10GBASE-ER 1550nm laser. • 10GBASE-EW 1550nm laser. • 10GBASE-LR 1310nm laser. • 10GBASE-LW 1310nm laser. • 10GBASE-LX4 WWDM 1300nm laser. Tx type • 10GBASE-SR 850nm laser. • 10GBASE-SW 850nm laser. •...

  • Page 129: Fdmi Commands

    Field Description The supported speed can be one or more of the following options: • 1 Gbps. • 2 Gbps. • 4 Gbps. • 8 Gbps. Port speed capability • 10 Gbps. • 16 Gbps. • 20 Gbps. Unknown is displayed for speeds other than the preceding ones. The current speed can only be one of the following options: •...

  • Page 130

    hba-id hba-id: Specifies an HBA by its ID in the format of xx:xx:xx:xx:xx:xx:xx:xx (hexadecimal). verbose: Displays detailed FDMI database information. If you do not specify this keyword, the command displays brief FDMI database information. Usage guidelines Only FCF and FCF-NPV switches support this command. Examples # Display the brief FDMI database information for all VSANs.

  • Page 131

    OS name/version: Microsoft Windows Server 2003 R2 for x86 CT payload len: 2112 Port WWN: 21:00:00:c0:dd:13:cc:d5 Supported FC4 types: FCP Supported speed: 10Gbps Current speed: 10Gbps Maximum frame size: 2048 OS device name: S05131F Host name: S05131F Table 43 Command output Field Description Node WWN...

  • Page 132: Fc Ping Commands

    Field Description The current speed can only be one of the following options: • 1 Gbps. • 2 Gbps. • 4 Gbps. • 8 Gbps. • 10 Gbps. Current speed • 16 Gbps. • 20 Gbps. • 32 Gbps. • 40 Gbps.

  • Page 133

    To abort the FC ping operation during the execution of this command, press Ctrl+C. Examples # FCping the address FFFC02 in VSAN 1. <Sysname> fcping fcid fffc02 vsan 1 FCPING fcid 0xfffc02: 128 data bytes, press CTRL_C to break. Reply from 0xfffc02: bytes = 128 time = 1.281 ms Reply from 0xfffc02: bytes = 128 time = 0.890 ms Reply from 0xfffc02: bytes = 128 time = 0.889 ms Reply from 0xfffc02: bytes = 128 time = 0.892 ms...

  • Page 134: Fc Tracert Commands

    Field Description 5 packet(s) transmitted Number of echo requests sent. 5 packet(s) received Number of echo replies received. Percentage of packets not responded to the total number of 0.00% packet loss packets sent. round-trip min/avg/max = Minimum/average/maximum response time, in 0.889/0.969/1.281 ms milliseconds.

  • Page 135

    20:00:00:05:30:00:18:db(0xfffcd7) 20:00:00:05:30:00:18:db(0xfffcd7) 20:00:00:0b:46:00:02:82(0xfffcd5) Fctracert completed. Table 45 Command output Field Description Route present for Path from a source to a destination. During the execution of the command, press Ctrl+C to abort the FC tracert press CTRL_C to break operation. 20:00:00:0b:46:00:02:82 WWN value.

  • Page 136: Support And Other Resources

    Related information Documents To find related documents, browse to the Manuals page of the HP Business Support Center website: http://www.hp.com/support/manuals For related documentation, navigate to the Networking section, and select a networking category. •...

  • Page 137: Conventions

    Conventions This section describes the conventions used in this documentation set. Command conventions Convention Description Boldface Bold text represents commands and keywords that you enter literally as shown. Italic Italic text represents arguments that you replace with actual values. Square brackets enclose syntax choices (keywords or arguments) that are optional. Braces enclose a set of required syntax choices separated by vertical bars, from which { x | y | ...

  • Page 138

    Network topology icons Represents a generic network device, such as a router, switch, or firewall. Represents a routing-capable device, such as a router or Layer 3 switch. Represents a generic switch, such as a Layer 2 or Layer 3 switch, or a router that supports Layer 2 forwarding and other Layer 2 features.

  • Page 139: Index

    Index A B D F I M N P R S T V W Z display interface vfc,7 display npv login,102 allowed-domain-id,24 display npv status,103 display npv traffic-map,105 display vsan port-member,19 bandwidth,3 display vsan status,20 bind interface,3 display zone,73 display zone member,74 default,6 display zone...

  • Page 140

    fip-snooping enable,1 13 rscn aggregation timer,45 fip-snooping fc-map,1 13 fip-snooping port-mode,1 14 shutdown,12 fspf cost,63 snmp-agent trap enable fc-fabric,46 fspf dead-interval,64 snmp-agent trap enable fc-name-service,47 fspf enable,65 snmp-agent trap enable fc-zone,88 fspf graceful-restart,65 Subscription service,131 fspf graceful-restart helper,66 fspf graceful-restart interval,67 fspf hello-interval,67...

Comments to this Manuals

Symbols: 0
Latest comments: