Fax Function Check By [Method B] And External Connection Function Check - Epson Artisan 810 Service Manual

Epson Artisan 810/835/837/710/725/730/Epson Stylus Photo PX810FW/TX810FW/PX820FWD/TX820FWD/PX830FWD/PX710W/TX710W/PX720WD/TX720WD/PX730WD/TX730WD
5. Enter fax mode by pushing the fax button.
6. Input fax number of PC on "R" unit. (Regarding FAX number, refer to the
telephone line simulator's manual.)
7. Push the "Start" button in "B&W" mode.
8. Push the "Back" button after being displayed as "Send another page?" on
LCD panel to send fax data from "R" unit to PC.
CHECK POINT OF "R" UNIT
Checked
Check Timing
Function
After sending of fax data
Fax Function
After receiving of fax
data
During calling of fax
(Step 9)
External
Connection (EXT
port) Function
During receiving fax data
(Step 10)
3.8.2.2 Fax Function Check by [Method B] and External
Connection Function Check
SETTING METHOD
Guaranteed
Unit
Telephone line
Fax cable
simulator
*Guaranteed unit means
*Regarding FAX number,
FAX function and EXT
refer to the telephone line
port perform correctly.
simulator's manual.
Guaranteed Epson Artisan
810/835/837/Epson Stylus
Photo PX810FW/
TX810FW/PX820FWD/
TX820FWD/PX830FWD
is represented by "G" unit
from this.
TROUBLESHOOTING
Check Point
Make sure that "R" unit sends fax data
correctly.
Make sure that "R" unit receives fax data
correctly.
Check if you can hear ringing tone from
telephone before receiving fax. In this
case, the telephone sounds ringing.
Check if you can't hear dial tone from the
telephone during receiving fax data. In this
case, the telephone doesn't sound dial tone.
Telephone
Fax cable
EXT port Repaired/refurbished
Epson Artisan 810/835/
837/Epson Stylus Photo
Fax cable PX810FW/TX810FW/
Line port
PX820FWD/
TX820FWD/PX830FWD
*Repaired/refurbished Epson Artisan
810/835/837/Epson Stylus Photo
PX810FW/TX810FW/PX820FWD/
TX820FWD/PX830FWD is
represented by "R" unit from this.
*Refer to Table 3-38 on page 94
default setting.
Fax Function/External Connection Function Check
CHECK PROCEDURE
[Sender: "R" unit => Receiver: "G" unit]
1. Set test chart on the document glass of "R" unit.
2. Enter fax mode by pushing the fax button.
3. Input fax number of "G" unit on "R" unit. (Regarding FAX number, refer to
the telephone line simulator's manual.)
4. Push the "Start" button in "B&W" mode.
5. Push the "Back" button after being displayed as "Send another page?" on
LCD panel to send fax data from "R" unit to "G" unit.
[Sender: "G" unit => Receiver: "R" unit]
1. Set test chart on the document glass of "G" unit.
2. Enter fax mode by pushing the fax button.
3. Input fax number of "R" unit on "G" unit. (Regarding FAX number, refer to
the telephone line simulator's manual.)
4. Push the "Start" button in "B&W" mode.
5. Push the "Back" button after being displayed as "Send another page?" on
LCD panel to send fax data from "G" unit to "R" unit.
6. Confirm if telephone rings correctly during calling tone of "R" unit rings.
7. Confirm if dial tone of telephone is lost during "R" unit receives fax data
without calling tone.
CHECK POINT OF "R" UNIT
Checked
Function
After sending of fax data
Fax Function
After receiving of fax
data
During calling of fax
(Step 6)
External
Connection (EXT
port) Function
During receiving fax data
(Step 7)
for
Check Timing Check Point
Make sure that "R" unit sends fax data
correctly.
Make sure that "R" unit receives fax data
correctly.
Check if you can hear ringing tone from
telephone before receiving fax. In this
case, the telephone sounds ringing.
Check if you can't hear dial tone from the
telephone during receiving fax data. In this
case, the telephone doesn't sound dial tone.
Revision G
98
Confidential