One-Touch Settable Item List - JUKI SC-922 Engineer's Manual

(2) One-touch settable item list

No. Function item
0 No function
1 Soft start stitching count
2 Material end sensor function
3 Thread trimming function by material end sensor EdTr
4 Number of stitches for material end sensor
6 Bobbin thread count function
7 Unit of bobbin thread counting down
8 Rotation count of reverse feed stitching
9 Thread trimming prohibiting function
10 Needle bar position specifying at machine stop
11 Operating sound of operation panel
13 Function of prohibiting start of sewing
machine by bobbin thread counter
14 Sewing counter
15 Function of thread wiping after thread trimming
21 Neutral presser lifting function
22 Function of switching needle up/down
compensating switch function
25 Thread trimming after rotating handwheel by hand CUTC
29 Back tack initial motion time
30 Function of reverse feed stitching on the way obT
31 Reverse feed stitching count on the way
32 Effective condition of reverse feed stitching
on the way at machine stop
33 Thread trimming function by reverse feed
stitching on the way
35 Number of rotation at low speed
36 Number of thread trimming rotation
37 Number of soft start rotation
38 One-shot speed
47 Holding time of automatic presser lifting
49 Work clamp lowering time
50 Setting of pedal specifications
51 Solenoid timing on compensation of reverse TSon
feed stitching at sewing start
52 Solenoid timing off compensation of reverse TSoF
feed stitching at sewing start
53 Solenoid timing off compensation of reverse TEoF
feed stitching at sewing end
55 Function of work clamp lifting after thread trimming
56 Function of lifting needle in a reverse rotation rATr
after thread trimming
58 Function of holding needle bar at predetermined HPoS
up/down positions
59 Function of A/M switching of reverse feed
stitching at sewing start
60 Function of stop immediately after reverse
feed stitching at sewing start
61 Time of holding needle bar at predetermined THPS
position
64 Switching speed of condensation and EBT
70 Work clamp soft down function
Abbrevi-
No.
ation
noP 71 Double reverse feed stitching function
SoFT 72 Machine startup selection function
Ed 73 Retry function
74 Function setting of MF thread trimming device
EdST 76 One-shot function
bob 84 Initial suction time of presser solenoid
rSTi 87 Pedal curve selection function
SbT 91 Function of prohibiting compensating
TrM
operation after rotating handwheel by hand
nPS
92 Function of reducing reverse feed stitching
SUnd
speed at sewing start
ASCT
93 Function of adding the needle up/down
compensating switch
nTo
94 Function of nonstop sewing between
WiP
continuous stitching and one-shot stitching
nPL
96 Setting of maximum rotation speed
CMSP 103 Delay time of needle cooler output OFF
124 Setting of energy saving function at standby SAvE
144 Setting of stitches count for canceling
TrSS alternate vertical output
146 Selection of alternate vertical output after
nobT thread trimming
obTS 147 Alternate vertical initial output
148 2-pitch output during reverse feed stitching
obTT at start and end
149 2-pitch inverted output during alternate
SPoS vertical output
STrM 150 2-pitch initial output
SSFT
151 Tie stitch adjustment function
SASS
154 Function of shortened stitching at start and
TFL
end
TFLW
155 Setting of neutral automatic presser lifting
FTr2
156 Thread clamp function
158 Function of shortened stitching during
thread trimming
163 Alternate vertical speed limit function
164 High-speed switching function by standing
pedal input
168 Remaining bobbin thread detection function bTd
FLAT
SbTo
SbTq
SEST
SdFL
– 65 –
Function item
Abbrevi-
ation
ACrA
FACr
FrET
MFTr
SHoT
TPUT
FPoS
PMAT
dSbT
MAdF
SbTC
SPd
TndL
dLST
TrdL
dL
SE2P
dL2P
2PiT
bTP
SESS
nPLd
TC
TrSS
FdLS
PdHi