JUKI SC-922 Engineer's Manual page 38

Output function list
Function code Abbreviation
0 noP No function
1 TrM Thread trimming output
2 WiP Thread wiper output
3 TL Thread release output
4 FL Presser lifter output
5 bT Reverse feed stitching output
6 EbT EBT cancel monitor output
7 SEbT Reverse feed stitching at start/end cancel monitor output
8 AUbT Sewing start/end cancellation/addition monitor output
9 SSTA Sewing machine stop state output
10 CooL Needle cooler output
11 bUZ Buzzer output
12 LSWo Revolution command output
13 vErT Alternate up/down amount conversion
(monitor) output
14 2PiT 2-pitch output
15 bCGo Bobbin replacement monitor output
16 TC Thread grasping enabled state monitor output Thread grasping enabled state is output.
17 CAbT S/EBT 1-time cancellation monitor output
18 SToP Stop state monitor output
19 AEbo Remaining check device air blow output
20 UdET Up position output
21 ddET Down position output
Input function setting connectors
Connector
Pin No. Display No. Initial value of function setting
No.
4 i01
5 i02
6 i03
7 i04
CN44
8 i05
9 i06
10 i07
11 i08
15 i09
16 i10
17 i11
18 i12
CN58
19 i13
20 i14
21 i15
22 i16
4 i17
5 i18
6 i19
7 i20
CN51
8 i21
9 i22
10 i23
11 i24
7 i25
11 i26
CN39
9 i27
5 i28
2 i29
CN48
1 i30
4 i31
CN36
5 i32
Function item
Machine head switch 1 input
Machine head switch 2 input
Machine head switch 3 input
Machine head switch 4 input
Machine head switch 5 input
Machine head switch 6 input
Machine head switch 7 input
Machine head switch 8 input
Option 1 input
Option 2 input
Option 3 input
Option 4 input
Option 5 input
Option 6 input
Option 7 input
Option 8 input
Option 9 input
Option 10 input
Option 11 input
Option 12 input
Option 13 input
Option 14 input
Option 15 input
Option 16 input
TSW (thread trimming switch input)
LSSW (low speed switch)
HSSW (low speed switch)
FL (presser lifter switch input)
SFSW (safety switch input)
noP (no function is assigned)
FL (presser lifter switch input)
bT (reverse feed stitching switch input)
(Standard setting)
Output of thread trimming signal
Output of thread wiper signal
Output of thread release signal
Output of presser lifting signal
Output of reverse feed stitching signal
State of one time cancel of reverse feed stitching at end function is output.
State of cancel of reverse feed stitching at start/end is output.
State of cancel or addition of automatic reverse feed stitching is output.
Sewing machine stop state is output.
Output for needle cooler
It is outputwhen the bobbin counter set value has been exceeded, an
error has occurred or the bobbin thread remaining amount is detected.
Revolution demanding command state is output.
Alternate up/down amount conversion signal is output.
2-pitch signal is output.
Sewing machine start-up prohibition state during bobbin replacement is output.
One-time cancellation state of the reverse feed stitching at the be-
ginning or end sewing is output.
Sewing machine operation prohibition state is output.
Air blow output when using the remaining check device
Up state output
Down state output
Output function setting connectors
Connector
Pin No.
No.
15
16
17
18
CN44
19
20
21
22
11
12
13
14
15
16
17
18
CN59
19
20
21
22
23
24
25
26
15
16
17
18
CN51
19
20
21
22
– 34 –
Remarks
Display No. Initial value of function setting
o01 Machine head LED 1 output
o02 Machine head LED 2 output
o03 Machine head LED 3 output
o04 Machine head LED 4 output
o05 Machine head LED 5 output
o06 Machine head LED 6 output
o07 Machine head LED 7 output
o08 Machine head LED 8 output
o09 Option 1 output
o10 Option 2 output
o11 Option 3 output
o12 Option 4 output
o13 Option 5 output
o14 Option 6 output
o15 Option 7 output
o16 Option 8 output
o17 Option 9 output
o18 Option 10 output
o19 Option 11 output
o20 Option 12 output
o21 Option 13 output
o22 Option 14 output
o23 Option 15 output
o24 Option 16 output
o25 Option 17 output
o26 Option 18 output
o27 Option 19 output
o28 Option 20 output
o29 Option 21 output
o30 Option 22 output
o31 Option 23 output
o32 Option 24 output