JUKI SC-922 Engineer's Manual page 26

(Start level ; U : User's mode, S : Service mode)
No. Item
14 Sewing counter Counting function of sewing (number of completion
of press)
15 Thread wiping Thread wiping operation after thread trimming is
function after specified.
thread trimming
21 Function of Function of needle up/down compensating switch on
neutral the operation panel can be changed.
presser lifting
(This function is disabled when No. 93 Needle
up/down switch additional function setting is "2.")
22 Needle up/down Function of the needle up/down correction switch is
correction switch changed over.
changeover
function
24 Number of Sewing speed set of end reverse feed stitching.
rotation of end Set point sews it at the speed that I set with No. 8
reverse feed in the case of 100.
stitching
25 Thread trimming Thread trimming operation after moving the needle
operation after away from its upper or lower position by turning the
turning the handwheel by hand is specified.
handwheel by
hand
26 Function selection Change the function of the reverse feed stitching
of reverse feed switch.
stitching switch
29 Initial time This function sets the suction time of initial motion
of back-tack of back-tack solenoid.
30 Function of Function of reverse feed stitching on the way
reverse feed
stitching on
the way
31 Number of stitches Number of stitches of reverse feed stitching on the
of reverse feed way.
stitching on the
way
32 Effective condition Effective condition of reverse feed stitching on the
of reverse feed way
stitching on the
way when the
sewing machine
is stopping
∗
Do not change the set values with asterisk (
of delivery is changed, it is in danger of causing the machine to be broken or the performance to be deteriorated.
Description
0 : Sewing counter function is not operative
1 : Sewing counter function is operative
(Every time thread trimming is performed)
2 : With the sewing counting switch input function
0 : Thread wiping is not carried out after thread
trimming
1 : Thread wiping is carried out after thread trimming
0 : Function of neutral automatic presser lifting is not
1 : Function of neutral automatic presser lifting is
operative.
2 : Neutral automatic presser lifting is valid and the
alternate motion can be performed by
depressing the panel backward.
0 : Needle up/down compensation
1 : One stitch compensation
0 : Thread trimming operation is carried out after
turning the handwheel by hand
1 : Thread trimming operation is not carried out
after turning the handwheel by hand.
0 : It is always a backstitch function
1 : It is Needle up/down switch function double
touch at the time of the stop
2 : It is Needle up/down switch function at the time
of the stop
3 : It is Needle lifting switch function at the time of
the stop
4 : It is reverse needle lifting switch function at
the time of the stop
0 : Function of reverse stitching on the way is not
operative.
1 : Function of reverse feed stitching on the way
is operative.
0 : Function is not operative when sewing machine
stops.
1 : Function is operative when the sewing machine
stops.
∗
) mark as they are functions for maintenance. If the standard set value set at the time
Setting range
0 to 2
0/1
0 to 2
0/1
100 to 3000
(sti/min)
0/1
0 to 4
50 to 500
(ms)
0/1
0 to 19
(Stitches)
0/1
– 22 –
Indication of
Setting level
function setting
U
1 4
U
1 5
U
2 1
U
2 2
S
2 4
U
2 5
S
2 6
U
2 9
U
3 0
U
3 1
U
3 2
Ref.
page
35
1
0
35
0
35
0
1 0 0
1
0
35
2 5 0
36
0
36
4
36
0