Page 1 Xerox 6030/6050/6050A Wide Format Printer User Guide 701P47273 Version 2.0 August 2007 Downloaded From ManualsPrinter.com Manuals...
Page 2 Global Knowledge & Language Services 800 Phillips Road Bldg. 845-17S Webster, NY 14580 Copyright © 2007 Xerox Corporation. All rights reserved. Printed in the United States of America. Copyright protection claimed includes all forms and matters of copyrighted material and information now allowed by statutory or...
Page 3 Format, has been revised to accomodate the Xerox 6050A Wide Format. The reader should assume that any topic, section, heading, sentence, or bullet not denoted as being related to either the 6030/6050 or 6050A Wide Format is applicable to both products.
Page 4 Conventions This User Guide uses the following symbols and conventions: < > key Indicates the keys on the keyboard. Press the <Enter> key. Indicates the menus and display items on the screens. Select either the [On] or [Off] buttons to display [Job Name], [Owner], and [Reason] in that order.
Page 5: Safety Notes
Read these safety notes carefully before using this product to ensure you operate the equip- ment safely. Your Xerox product and recommended supplies have been designed and tested to meet strict safety requirements. These include safety agency approval, and compliance with established environmental standards.
Page 6 1989 Regulation. Customers wishing to complete safety testing should contact Xerox for advice prior to any test implementation. Xerox equipment should, however, be properly and regularly serviced and maintained at all times.
Page 7 MISLEADING RESULTS AND MAY CAUSE DEATH, PERSONAL INJURY AND/OR DAMAGE TO PROPERTY. QUESTION: I would like to carry out my own safety tests on the Xerox equipment in my pre- mises. ANSWER: You may, of course, request such tests as you deem necessary to satisfy yourself that your Xerox equipment is safe.
Page 8: Electrical Supply
PLEASE NOTE: YOU MUST ENSURE THAT YOUR XEROX EQUIPMENT IS SAFE AT ALL TIMES Electrical Supply This product shall be operated from the type of electrical supply indicted on the product 's data plate label. If you are not sure that your electrical supply meets the requirements, please consult your local power company for advice.
Page 9: Emergency Power Off
• This equipment is to be used on a dedicated 20A, 208-240 Vac 60Hz circuit or 16A, 220-240 Vac 50Hz circuit. The equipment must be connected to a grounded main outlet. If this machine needs to be moved to a different location, contact a Xerox service representative or your authorized local representative or service support organization.
Page 10: Disconnect Device
• Always follow all warnings and instructions that are marked on or supplied with the equipment. • Always exercise care when moving or relocating equipment. Please contact your local Xerox/ Fuji Xerox Service Department, or your local support organization to arrange relocation of the product to a location outside of your building.
Page 11: Maintenance Information
Contact your Xerox sales representative (1-800-ASK-XEROX) to determine whether this Xerox product is part of the program. For more information about Xerox environmental programs, visit http://www.xerox.com/environment. If you are managing the disposal of your Xerox product, please note that the prod- Safety Notes Downloaded From ManualsPrinter.com Manuals...
Page 12: For Consumables
Changes and modifications to this equipment not specifically approved by Xerox/ Fuji Xerox may void the user's authority to operate this equipment. Shielded interface cables must be used with this equipment to maintain compli- ance with FCC regulations in the United States and the Radio Communications Act 1992 in Australia/New Zealand as applicable.
Page 13: Product Safety Certification
Canadian EME This Class "A" digital apparatus complies with Canadian ICES-003. Cet appareil numérique de la classe "A" est conforme à la norme NMB-003 du Canada. Product Safety Certification This product is certified by the following Agencies using the Safety standards listed. AgencyStandard TUV Rheinland of North America, Inc.
Page 14: Regulatory Information
Regulatory Information CE Mark The CE mark applied to this product symbolizes Xerox's declaration of conformity with the following applicable Directives of the European Union as of the dates indi- cated: January 1, 1995: Council Directive 72/23/EEC amended by Council directive 93/ 68/EEC, approximation of the laws of the member states related to low voltage equipment.
Page 15: Environmental Compliance
Xerox ENERGY STAR equipment is preset at the factory to enter a ”low power” state and/or shut off completely after a specified period of use. These energy-sav- ing features can reduce product energy consumption in half when compared to conventional equipment.
Page 16 Terra Choice Environmental Services, Inc. of Canada has verified that this product conforms to all applicable Environmental Choice EcoLogo requirements for mini- mized impact to the environment. As a participant in the Environmental Choice program, Xerox Corporation has determined that this product meets the Environmental Choice guidelines for energy efficiency.
Page 17: Product Recycling And Disposal
Xerox product is part of the program. For more information about Xerox environmental programs, visit www.xerox.com/environment. If you are managing the disposal of your Xerox product, please note that the prod- uct contains lead, mercury and other materials whose disposal may be regulated due to environmental considerations.
Page 18: Illegal Copies And Printouts
Illegal Copies and Printouts Congress, by statute, has forbidden the reproduction of the following subjects under certain circumstances. Penalties of fine or imprisonment may be imposed on those guilty of making such reproductions. 1. Obligations or Securities of the United States Government, such as: Certificates of Indebtedness National Bank Currency Coupons from Bonds...
Page 19 1. Stamps and other representatives of value, of whatever denomination, which have been or may be issued under any Act of Congress. 2. Adjusted Compensation Certificates for Veterans of the World Wars. 3. Obligations or Securities of any Foreign Government, Bank, or Corporation. 4.
Page 20 Canada Parliament, by statute, has forbidden the reproduction of the following subjects under certain circumstances. Penalties of fine or imprisonment may be imposed on those guilty of making such reproductions. 1. Current bank notes or current paper money. 2. Obligations or securities of a government or bank. 3.
Page 21: Other Countries
This list is not inclusive and no liability is assumed for either its completeness or accuracy. In case of doubt, contact your legal counsel. Safety Extra Low Voltage Approval These Xerox Digital Copiers/Printers are in compli- ance with various governmental agencies and national safety regulations. All system ports meet...
Page 22 xviii Illegal Copies and Printouts Downloaded From ManualsPrinter.com Manuals...
Page 23: Table Of Contents
1.11 Cutting Roll Media ......................24 Cutting Roll Media Manually..................25 Chapter 2 Printer Overview Overview of the 6030/6050/6050A Wide Format Printer ..........32 What is the 6030/6050/6050A Wide Format Printer?..........32 Print Service Operations ................... 36 Main Printing Functions..................... 38 Printer Control Panel Usage..................
Page 24 3.12 Software Option (Print Services on Web, 6030/6050)..........101 3.13 Software Option (Web Printer Management Tool, 6050A) .......... 102 3.14 Change Password (Print Services on Web, 6030/6050) ..........103 3.15 Change Password (Web Printer Management Tool, 6050A) ........104 3.16 Change Default Language (Print Services on Web, 6030/6050)......... 105 3.17 Change Default Language (Web Printer Management Tool, 6050A) ......
Page 25 Split Drawing ......................134 Message Option ...................... 136 Printed Copy......................138 Output Option ......................139 Size Recognition ..................... 142 Color Option ......................144 Transform ........................ 145 Define Single Pen....................147 Define Multi Pen ...................... 151 Pen Option....................... 152 Emulation ........................ 153 PS Command ......................
Page 26 Printer Control Panel Menu (6030/6050)..............197 Printer Control Panel Menu (6050A) ................203 Test Printing (6030/6050 only)..................207 Managing the Job and Error Logs (6030/6050 only) ........... 208 Job Log........................208 Error Log (6030/6050 only) ..................210 Reprinting (6030/6050 only) ..................212 Billing Meter Confirmation (6030/6050)...............
Page 27 Message List (6030/6050 only) ................249 Chapter 7 Maintenance Loading Toner......................252 Chapter 8 Problem Solving Check the Control Panel(s) ..................256 Poor Image Quality ...................... 257 Other Problems ......................258 Printer Troubleshooting....................259 Jams in the Feeder (Roll Media) ................261 Jams in the Printer and Ejection Port ..............
Page 28 Downloaded From ManualsPrinter.com Manuals...
Page 29: Downloaded From Manualsprinter.com Manuals
Chapter Chapter 0 Product Overview Downloaded From ManualsPrinter.com Manuals...
Page 30: Product Configurations
Product Configurations The following product configurations and options are available for the Xerox 6030/6050/6050A Wide Format Printer and the Xerox 6030/6050/6050A Wide Format Copier/Printer. Xerox 6030/6050/6050A Wide Format Printer This unit is a printer only. Refer to the printer sections of this guide for information about its setup, features, and usage.
Page 31 ® System and the FreeFlow Accxes Controller. Xerox 6030/6050 Wide Format Printer with Scan System (HFT controller shown is not available with the 6050A) Xerox 6030/6050/6050A Wide Format Options You may acquire additional hardware and software options for all units.
Page 32: Major Components
Major Components Major Components: Front ( *6030/6050 Copier/Printer only ) Name Function Document table Documents to be scanned are inserted here. Setup screen Used to set up copy jobs, map originals to the (touch screen) installed media, display messages and procedures, and provide troubleshooting help, e.g., for jam clearance.
Page 33: Downloaded From Manualsprinter.com Manuals
Switches the power to the scanner on and off. Name Function Toner supply port The toner is refilled through this port. Major Components: Rear ( *6030/6050 Copier/Printer only ) Name Function *1 Document ejection port Documents exit the scanner from this location. *2 Power outlet socket...
Page 34 Name Function *4 Remote switch A selector switch that enables the user to switch the power to both the scanner and the printer on and off from the Main Power Switch. *5 Interface connector The connector to which the printer is connected.
Page 35: Power On/Off
No power is consumed when the Circuit Breaker Switch is in the OFF position, even though the power plug is connected to the power source. Powering On 6030/6050 Set the Remote Switch to [Connect]. When the Remote Switch is set to...
Page 36 Controller. The 6050A will not operate unless Accxes controller is ON. Powering Off 6030/6050 Switch off the power following the steps below. Never switch off the power while the machine is printing. Failure to observe this precaution may result in paper jams in the high-temperature areas of the printer.
Page 37 Powering Off 6050A Switch off the power following the steps below. Never attempt to switch off the power while the machine is printing. Failure to observe this precaution may result in paper jams in the high-temperature areas of the printer. Press the <Menu>...
Page 38: Power Save Mode
This mode reduces the temperature of the fuser more than Low power mode 1. The parameters that can be set up are only [ON] and [OFF] on the 6030/ 6050, and the time that must elapse before the mode activates is 5 to 120 minutes;...
Page 39 Refer to "3.8 System Parameter Setup (Print Services on Web, 6030/6050)" for changing the power save mode settings from the printer control panel. 1.4 Power Save Mode Downloaded From ManualsPrinter.com Manuals...
Page 40: Printer Control Panel Overview
Refer to section "2.2 Printer Control Panel Usage" and Chapter 5 for detailed explanations of the use of the printer control panel. It is seldom necessary to use the printer control panel on the 6030/6050 Wide Format Copier/Printer because the same settings usually can be made using either the copier control panel or Print Services on Web, the built-in web interface.
Page 41: Print Services On Web Overview (6030/6050)
Print Services on Web Overview (6030/ 6050) Print Services on Web is web server software which is pre-installed in the 6030/ 6050 Wide Format Printer and Copier/Printer. Print Services on Web provides a user-friendly way to perform printer setup, communication (port) setup, job and error log management, and other procedures via a web browser.
Page 42: Operating Modes
[Status tab] Check the status of the Printer or Copier/Printer. Start a print job. [Print Setup] tab View the logical printer settings. Refer to section "1.7 Logical Printers Overview (6030/6050)" to learn more about logical printers. Downloaded From ManualsPrinter.com Manuals...
Page 43 • View and change the machine configuration. • View and change communications configurations. • Manage ftp users. [Tools] tab • Print a test pattern to verify machine (printer) operation. • Print a Diagnostic Report. 1.6 Print Services on Web Overview (6030/6050) Downloaded From ManualsPrinter.com Manuals...
Page 44: Logical Printers Overview (6030/6050)
Stored Jobs are to copying, that is, both reduce setup time and increase efficiency by using previously saved job settings. A maximum of one hundred logical printers can be set up within one 6030/6050 Wide Format Printer or Copier/Printer for each supported data format.
Page 45: Loading Roll Media
Loading Roll Media The message ‘Replace xxx media." will display when there is no media loaded or when the roll in use runs out. The media size displayed on the control panel will turn off when there is no media in the machine. Two rolls of media can be loaded in each of the media trays.
Page 46 While pulling on the lever located in the end of the roll paper shaft, remove the paper core in the direction of the arrow. Pulling the lever releases the lock and allows the roll to be removed from the shaft. There is an area at the front of the tray on which the roll paper can be placed.
Page 47 Set up the media parameters on the copier control panel. " Setting Up Media" For the 6050A and 6030/6050 Printers without copiers, the media parameters also may be set up on the printer control panel. "Chapter 5 Additional Operations from the Printer Menu"...
Page 48: Drawer Media Size Indicators
Drawer Media Size Indicators The media size indictors help the user identify the media that is loaded in each of the drawers. These indicators are visible on the right hand side of the drawers. Usage instructions begin on the next page. The following types are available.
Page 49: Inserting Media Size Sheets
Inserting media size sheets Open the tray. Remove the media size sheet. Fold the sheet so that the size loaded is displayed. Insert the media size sheet. 1.9 Drawer Media Size Indicators Downloaded From ManualsPrinter.com Manuals...
Page 50 Gently but firmly close the media tray. Downloaded From ManualsPrinter.com Manuals...
Page 51: Loading Media For Manual Feeding
1.10 Loading Media for Manual Feeding Adjust the (MSI) Multi Sheet Inserter/ Manual Feed Unit's side guides to fit the size of the media that is to be printed. Set the correct media series for the manual feed sheet. Place the side of the media to be printed face up, and align it with the (MSI) Multi Sheet Inserter/Manual Feed Unit's side guides.
Page 52: Cutting Roll Media
Automatic cut: This involves making selections on the printer control panel. Refer to the section "5.7 Billing Meter Confirmation (6030/6050)" for the 6030/6050 and "5.8 Billing Meter Confirmation (6050A)" for the 6050A in "Chapter 5 Additional Operations from the Printer Menu" for details about automatic cutting.
Page 53: Cutting Roll Media Manually
Cutting Roll Media Manually Cutting the Front Roll Open the media tray. Pull the lever to open the tray cover. Lever Rotate the roll media until the lead edge is gripped by the roller. 1.11 Cutting Roll Media Downloaded From ManualsPrinter.com Manuals...
Page 54 Rotate the knob until the media's lead edge protrudes from the tray outlet. Grasp the cutter by the handle and slide it to the opposite side of the tray to cut the paper. CAUTION: Use the cutter handle to prevent personal injury which may result from sliding your fingers along the sharp, metal cutting bar.
Page 55 Close the media tray. Cutting the Rear Roll Open the media tray. Rotate the roll paper until the lead edge is gripped by the roller. 1.11 Cutting Roll Media Downloaded From ManualsPrinter.com Manuals...
Page 56 Rotate the knob until the media's lead edge protrudes from the tray outlet. Pull the lever to open the tray cover. Rotate the knob until the paper passes through the tray outlet. Grasping the cutter by the handle, slide the cutter to the opposite side of the tray to cut the paper.
Page 57 Return the media to its original location by rotating the knob until the lead edge can be seen in the window. Close the media tray. 1.11 Cutting Roll Media Downloaded From ManualsPrinter.com Manuals...
Page 58 Downloaded From ManualsPrinter.com Manuals...
Page 59: Chapter 2 Printer Overview
Chapter Chapter 0 Printer Overview Chapter 2 Downloaded From ManualsPrinter.com Manuals...
Page 60: Overview Of The 6030/6050/6050A Wide Format Printer
What is the 6030/6050/6050A Wide Format Printer? The 6030/6050/6050 Wide Format printer processes print jobs that it receives from a client. The 6030/6050/6050A Wide Format printer enables all types of image data to be printed in the supported formats, including standard and non- standard size documents, enlarged and reduced images, and split (fragmented) images.
Page 61 • Ethernet (100Base-TX and 10Base-T) • RS232C • Centronics (optional) • VPI (optional) Communication Interfaces (6050A) The following communication interfaces are supported. • TCP/IP 10/100/1000 • • TFTP 2.1 Overview of the 6030/6050/6050A Wide Format Printer Downloaded From ManualsPrinter.com Manuals...
Page 62 Printing Methods (6030/6050) Documents may be submitted from a client to the 6030/6050 Wide Format Printer using any of the following. • Ethernet (Direct) Printing This capability is for UNIX systems. Printing takes place over TCP/IP networks using the ftp and lpr commands.
Page 63 Sun Solaris operating systems. Using the Accxes Client Tools simple user interface, the user can submit documents to the 6050A Wide Format printer. Refer to the Xerox 6050A Accxes Client Tools User Guide for details on available functions. •...
Page 64: Print Service Operations
• job log and error log management • reprinting of the most recent print job (6030/6050 only) • displaying billing meter information Refer to "2.2 Printer Control Panel Usage" for more details on the printer control panel and its usage.
Page 65 Print Services on Web (6030/6050 only) Print Services on Web is web server software which is pre-installed in the 6030/ 6050 Wide Format. Print Services on Web provides a user-friendly way to perform printer setup, communication (port) setup, log management, and other procedures via a web browser.
Page 66: Main Printing Functions
Stored Jobs are to copying, that is, both reduce setup time and increase efficiency by using previously saved settings. A maximum of one hundred logical printers can be set up within one 6030/6050 Wide Format Printer or Copier/ Printer for each supported data format.
Page 67 • Refer to "3.8 System Parameter Setup (Print Services on Web, 6030/6050)" for details on setting up the logical printer extensions. • Refer to "4.1 Creating a New Logical Printer" for help in setting up logical printers. Document Size Input...
Page 68 Size Mapping Size mapping is the process of setting up a table that establishes relationships between input document sizes and output image sizes. When size mapping is finished (must be done prior to printing), documents can be enlarged or reduced automatically based on the table entries.
Page 69 Refer to the "Transform" section of "4.3 Logical Printer Print Settings" for details on available functions. Mirror image 90-degree rotation Input document Output images 2.1 Overview of the 6030/6050/6050A Wide Format Printer Downloaded From ManualsPrinter.com Manuals...
Page 70 The most recently printed document can be reprinted. The print quantity also can be specified. Reprinting is not possible with the Xerox 6030 WF or Xerox 6050 WF if a copy job is performed after the print operation. Refer to "5.6 Reprinting (6030/6050 only)" for details on available functions.
Page 71: Canceling Jobs
"4.5 Print Services on Web: Job and Log" for details on Print Service on Web operations. Meter Display The billing meters can be checked from both Print Services on Web (6030/6050 only) and the printer control panel. Refer to "4.6 Print Services on Web: Status" for details on web operations, and "5.7 Billing Meter Confirmation (6030/6050)"...
Page 72: Printer Control Panel Usage
Printer Control Panel Usage This section describes the names and functions of the printer control panel components. <Power Saver> button [Processing] lamp (green) Activates the energy-saving mode. Indicates the printing status. Also cancels the energy-saving mode. Printing in process Energy-saving mode Blinking Receiving print data activated.
Page 73: Basic Printer Control Panel Operations
Basic Printer Control Panel Operations The printer must be in the offline mode before settings can be changed. Pressing the <Menu> key switches the printer to the offline mode and displays the menu screen. Button Functions The following buttons are used to navigate the menu screen. <Menu>...
Page 74: Overview Of The Operation Menu
Sets up the system management information, such as the system date and power save mode settings. Refer to "3.2 Communication Parameter Setup (Printer Control Panel, 6030/ 6050)" for the 6030/6050 and "3.3 Communication Parameter Setup (Printer Control Panel, 6050A)" for the 6050A for setup procedures.
Page 75 Refer to "5.4 Test Printing (6030/6050 only)" for logical printer details and operations. JOB LOGGING MENU Prints job and error logs. Refer to "5.5 Managing the Job and Error Logs (6030/6050 only)" for logical printer details and operations. OFFLINE PLOT MENU Reprints the most recently printed job.
Page 76 Operation Examples This section provides examples of how to select menu items. <Menu> key Ready to print Press the <Menu> key. The machine will enter the offline mode. MENU NETWORK/PORT SET < > key Press the < > key. The top selection in the [NETWORK/PORT MENU SET] menu will display.
Page 77 Setting Up a Value This section provides an example of setting up a value. SYSTEM PARAMETER Select the menu item that you want to set Smoothing up so that it displays on the screen. < > key Press the < >...
Page 78 Entering Numbers and Characters This section provides examples of how to enter numbers and characters. Select the menu item that you want to set SYSTEM PARAMETER Low power mode1 < > key Press the < > key. The current setting for the selected item will Timer Value display.
Page 79: Print Services On Web (6030/6050)
Print Services on Web (6030/6050) Print Services on Web is web server software which is pre-installed in the 6030/ 6050 Wide Format. Print Services on Web enables the user to perform the following procedures from a workstation using a web browser.
Page 80: Starting And Exiting Print Services On Web
This section explains how to start and exit Print Services on Web. Start Print Services on Web Start the browser. Enter the URL for the 6030/6050 Wide Format (http://Home name or IP address) in the browser's address field, and then press the <Enter> key.
Page 81: Print Services On Web Organization
The administrator page (see next page) displays after the user selects the [Administrator page] button on the user page, and then enters the user name and password in the logon dialog box. 2.3 Print Services on Web (6030/6050) Downloaded From ManualsPrinter.com Manuals...
Page 82 The administrator page permits the following. [Job and Log] tab • Check the status of jobs in the print queue. • View and print the job log and the error log. • Cancel a print job. • Change the priority of a print job. [Status tab] •...
Page 83: Online Help
Click the Help [?] button displayed at the top, right corner of the window to display the online help. The online help enables you to answer many questions related to using Print Services on Web. 2.3 Print Services on Web (6030/6050) Downloaded From ManualsPrinter.com Manuals...
Page 84: Freeflow Accxes Web Print Management Tool (6050A)
Network bandwidth and speed • Amount of data being transmitted to or from the printer’s Controller • Network traffic The Web Printer Management Tool provides the following services to users of Xerox Wide Format Printers. Chapter 2 Printer Overview Downloaded From ManualsPrinter.com Manuals...
Page 85: Users
Users • View printer status (including media inventory) and the print queue • View the printer defaults • View the Job Accounting mode for remote print jobs • Generate test prints showing configuration data (such as the Controller’s TCP/ IP address) System Administrators with the Password •...
Page 86: Using Web Print Management Tool Main Menu
Using Web Print Management Tool Main Menu The Main Menu contains six selections in hypertext form allowing you to jump to other web pages. P r i n t e r Configuration Emulations S y s t e m Utilities Help Queue Defaults...
Page 87: Chapter 3 Printer Setup
Chapter Chapter 0 Printer Setup Chapter 3 Downloaded From ManualsPrinter.com Manuals...
Page 88: Communication Parameters
Copier/Printer is connected to the network, the communication parameters must be set up. The communication parameters can be set up from the printer control panel or from Print Services on Web (6030/6050). This section explains how to use both methods to perform the setup procedures. Explained, too, is the procedure for printing a list of the communication parameters.
Page 89 TCP/IP The communication parameter nomenclature on the printer control panel will sometimes differ from the nomenclature on Print Services on Web (6030/ 6050) or Web Printer Management Tool (6050A). The Print Service on Web and Web Printer Management Tool nomenclature appears in bold type in the table below.
Page 90 \*The ROUTING TABLE can be edited if [Static Routing] is set to [Enable]. A maximum of 512 items can be saved in the routing table. The [Registration Not Possible] screen will display if the number of items exceeds 512. Menu Item Description ROUTING TABLE Select [ADD] to enter additional routing...
Page 91 The following TCP/IP communication parameters can be set up for the 6050A using using the printer control panel on the device itself or using the Web Printer Management Tool. Menu Item Description Ethernet Setting Selects the ethernet setting/speed duplex layer. The default setting is [AUTO].
Page 92 Serial (6030/6050 Only) The serial communication parameters are listed below. The communication parameter nomenclature on the printer control panel will sometimes differ from the nomenclature on Print Services on Web. The Print Service on Web nomenclature appears in bold type in the table below.
Page 93 Menu Item Description Job Separation Sets up the job separation option. The default setting is (Page limit) [NO]. [YES] Starts data conversion once the command that recognizes the end of the data is received, even if it occurs midway through the file.
Page 94 Centronics (optional, 6030/6050 Only) The Centronics communication parameters are presented below. Menu Item Description Ack Mode The Ack mode is selected from [MODE0], [MODE1], [MODE2], [MODE3], and [MODE7]. The default setting is [MODE0]. DMA Timeout The timeout value for data input is entered within a range of 1 to 255 seconds.
Page 95 VPI (optional, 6030/6050 Only) The following VPI communication parameters must be set up. Menu Item Description REPORT Determines if the host will be notified offline of the media running out. OFFLINE The default setting is [NO]. [YES] Issues offline notification.
Page 96 SNMP (6030/6050 Only) The communication parameters listed below must be set up. SNMP must be set up in Print Services on Web. The communication parameter nomenclature on the printer control panel will sometimes differ from the nomenclature on Print Services on Web. The Print Service on Web nomenclature appears in bold type in the table below.
Page 97: Communication Parameter Setup (Printer Control Panel, 6030/6050)
After setting up all of the parameters, switch the printer power off and then on for the changes to take effect. TCP/IP Setup 3.2 Communication Parameter Setup (Printer Control Panel, 6030/6050) Downloaded From ManualsPrinter.com Manuals...
Page 98 PORT SETTING Display [TCP/IP] on the selection screen, TCP/IP and then press the < > key. TCP/IP Select the item that is to be set up with the Default Parser use of the < > and < > keys, and then press the <...
Page 99 < > and < > keys, and then press the < > key. [Handshake], [Baud Rate], [Parity], [Data Bit], [Stop Bit], [EOP Timeout], [Output Response], and [Job Separation] will be displayed in that order. 3.2 Communication Parameter Setup (Printer Control Panel, 6030/6050) Downloaded From ManualsPrinter.com Manuals...
Page 100 Select the parameters with the use of the Baud Rate < > and < > keys, and then press the <Set> key. An asterisk [*] will display on the right side of the parameters once they have been set. Centronics (optional) Setup PORT SETTING Display [CENTRO] on the setup item CENTRO...
Page 101 < > and < > keys, and then press the <Set> key. An asterisk [*] will display on the right side of the parameters once they have been set. 3.2 Communication Parameter Setup (Printer Control Panel, 6030/6050) Downloaded From ManualsPrinter.com Manuals...
Page 102: Communication Parameter Setup (Printer Control Panel, 6050A)
< > key. • Refer to the section TCP/IP Setup in "3.2 Communication Parameter Setup (Printer Control Panel, 6030/6050)" for information on how to set the [IP ADDRESS], [IP SUBNET MASK], and [IP GATEWAY] IP addresses.. [DHCP] and [RARP/BOOTP] have the option of either being enabled or disabled.
Page 103: Communication Parameter Setup (Print Services On Web, 6030/6050)
Start Print Services on Web, enter the Administrator mode, and select the [Properties] tab. Refer to "2.3 Print Services on Web (6030/6050)" for details about starting Print Services on Web and logging on as Administrator. The displayed [Print settings] were set up earlier using the selections on the [Print Setup] and the [Properties] tabs.
Page 104 Select the interface or protocol ([TCP/IP], [Serial], [Centro], [VPI], [SNMP]) to be set up from the [System parameters] menu. The setup selections will display in the right-hand pane of the window. In the example below, [Serial] has been selected. • Only standard features and installed options are listed in the [System parameters] menu.
Page 105 [Print] button. After setting up all of the parameters, switch the Main Power Switch off and then on to enable the changes to take effect. 3.4 Communication Parameter Setup (Print Services on Web, 6030/6050) Downloaded From ManualsPrinter.com Manuals...
Page 106: Communication Parameter Setup (Web Printer Management Tool, 6050A)
Communication Parameter Setup (Web Printer Management Tool, 6050A) • Consult Web Printer Management Tool help system for details on communication parameter setup of the 6050A. Chapter 3 Printer Setup Downloaded From ManualsPrinter.com Manuals...
Page 107: System Parameter Setup (Printer Control Panel, 6030/6050)
Control Panel, 6030/6050) The following system parameters can be set up from the printer control panel. These parameters can be set up on the copier control panel on the Xerox 6030/6050 Copier/Printers. If the parameters are set up on both the printer control panel and the copier control panel, the most recent settings will take precedence.
Page 108 • The sequence in which jobs are printed after the power is restored is based on the ID numbers that were assigned when each job was received. Net Cont. Time Not available 6030/6050 Printer Control Panel Example Procedure MENU Press the < > key with [MENU]/[SYSTEM SYSTEM PARAMETER PARAMETER] displayed.
Page 109 The changed parameters are saved to the system when the <Set> key is pressed. It is not necessary to save each change individually. 3.6 System Parameter Setup (Printer Control Panel, 6030/6050) Downloaded From ManualsPrinter.com Manuals...
Page 110: System Settings Setup (Printer Control Panel, 6050A)
System Settings Setup (Printer Control Panel, 6050A) The following system parameters can be set up from the printer control panel. • Refer to "2.2 Printer Control Panel Usage" for detailed instructions on printer control panel operations. Menu Item Description TCP/IP Allows the entering of an IP Address, IP Subnet Mask and an IP Gateway address.
Page 111 6050A Printer Control Panel Example Procedure MENU Press the < > key with [MENU]/[SYSTEM SYSTEM SETTINGS SETTINGS] displayed. SYSTEM SETTINGS Scroll to the item you wish to set up using TCP/IP the < > and < > keys. [TCP/IP], [Date/ Time], and Timers will display, in that order.
Page 112: System Parameter Setup (Print Services On Web, 6030/6050)
The system parameters listed below can be set up from Print Services on Web. These procedures are performed on the Administrator page. Refer to "3.4 Communication Parameter Setup (Print Services on Web, 6030/6050)" for information about setting up the [TCP/IP], [Serial], [Centro], [VPI], and [SNMP] selections in the [System Parameters] menu on the Properties tab.
Page 113 Sets up the internal clock. The parameters are set in the order year, month, day, hour, and minutes. Procedure Start Print Services on Web, log in as Administrator, and display the [Properties] tab. 3.8 System Parameter Setup (Print Services on Web, 6030/6050) Downloaded From ManualsPrinter.com Manuals...
Page 114 Select the item that is to be set up from the [System parameter menu], for example, [Priority], [Replot], [Print density], [Paper Width for Special A], [Job Recovery], [Exclusive access time out], [Extension], and [Set date]. Setting Up [Priority] The [Priority] parameter in Print Services on Web is the same as the [Print service] parameter on the printer control panel.
Page 115 [Reset to default] to return to the factory default setting. Setting Up [Print Density] Select [Print density] from the [System parameters] menu. The Print density selections will display in the right pane. 3.8 System Parameter Setup (Print Services on Web, 6030/6050) Downloaded From ManualsPrinter.com Manuals...
Page 116 Enter a positive or a negative number between -99 and +99 to set up the default print density. Larger negative numbers lighten the prints. Higher positive numbers darken the prints. The factory default setting is [0]. Press the [Apply] button to save the new setting, [Cancel] to revert to the existing setting, or [Reset to default] to return to the factory default setting.
Page 117 [Reset to default] to return to the factory default setting. Setting Up [Extension] Select [Extension] from the [System parameters] menu. The Extension selections will display in the right pane. 3.8 System Parameter Setup (Print Services on Web, 6030/6050) Downloaded From ManualsPrinter.com Manuals...
Page 118 Select the required format from [Data format]. As required, add or delete an extension: Add an extension To add a new extension, enter an extension name of eight characters or less in the text field, and then click the [Add] button. Delete an extension To delete an extension, click the [Delete] button.
Page 119 If the time selections are not displayed, drag the bottom scroll bar to the right to display them. Enter the time. Press the [Apply] button to save the new setting, or press [Cancel] to revert to the existing setting. 3.8 System Parameter Setup (Print Services on Web, 6030/6050) Downloaded From ManualsPrinter.com Manuals...
Page 120: System Parameter Setup (Web Printer Management Tool, 6050A)
System Parameter Setup (Web Printer Management Tool, 6050A) • Consult Web Printer Management Tool help system for details on setting up system parameters for the 6050A. Chapter 3 Printer Setup Downloaded From ManualsPrinter.com Manuals...
Page 121: Printing A Configuration List (6030/6050)
SET: to Print. displayed. The list of settings will be printed. From Print Services on Web Start Print Services on Web, log in as Administrator, and select the [Properties] tab. 3.10 Printing a Configuration List (6030/6050) Downloaded From ManualsPrinter.com Manuals...
Page 122 Select [Print Settings] in the System parameters menu. The current print settings will display in the right pane. Using the scrollbar on the right side of the window, scroll to the bottom of the Print Settings list, and then select the [Print] button. The printer will print a configuration list that is identical to the list from the printer control panel.
Page 123 An example of the configuration list (settings printout) is shown below. 3.10 Printing a Configuration List (6030/6050) Downloaded From ManualsPrinter.com Manuals...
Page 124 Description of the Configuration List Contents The contents of configuration list are explained below. Displayed Item Description H/W CONFIG Model Product name Software Version Installed version of the printer software RAM Total Displays the amount of memory installed in the printer.
Page 125: Printing A Configuration List (6050A)
3.11 Printing a Configuration List (6050A) The procedures below explain how to print a configuration list that shows the hardware and software configuration, communication parameter (port) settings, and system parameter settings of the printer. This list may be printed from either the printer control panel or Web Printer Management Tool.
Page 126 Select the [Test Print] sub-tab that appears. Depending upon your information requirements, click on the [Minimal], [Normal], [Full], or if PostScript is available, [PostScript] test print buttons. Explanations of each of these options are available from the Web Printer Management Tool interface. Chapter 3 Printer Setup Downloaded From ManualsPrinter.com Manuals...
Page 127 An example of the configuration list (settings printout) is shown below. 3.11 Printing a Configuration List (6050A) Downloaded From ManualsPrinter.com Manuals...
Page 128 Description of the Configuration List Contents The contents of the configuration list are explained below. Category Description Controller Configuration Displays data such as controller date/time, firmware version, size of hard disk, etc. Optional Controller Displays which optional features of the 6050A have been activated. Features Print Engine Displays data such as the set resolution of the 6050A, power saver...
Page 129: Software Option (Print Services On Web, 6030/6050)
The [Software Option] selection on the Print Services on Web [Properties] tab displays all installed optional software and related Feature Key (Key Install Key) information, for example, for the PostScript Driver. 3.12 Software Option (Print Services on Web, 6030/6050) Downloaded From ManualsPrinter.com Manuals...
Page 130: Software Option (Web Printer Management Tool, 6050A)
3.13 Software Option (Web Printer Management Tool, 6050A) Similar to the [Software Option] selection under the Print Services on Web [Properties] tab, the the [Features] selection under the [Configuration] tab in Web Print Management Tool allows for the display of what features are currently installed on the 6050A.
Page 131: Change Password (Print Services On Web, 6030/6050)
Enter the new password in the [New password:] field. Enter the new password again in the [Confirm New Password:] field. Click the [Apply] button to save the change, or [Cancel] to undo it. 3.14 Change Password (Print Services on Web, 6030/6050) Downloaded From ManualsPrinter.com Manuals...
Page 132: Change Password (Web Printer Management Tool, 6050A)
3.15 Change Password (Web Printer Management Tool, 6050A) Maintain a record of the new password in a secure location. Select the [Utilities] tab on the main navigation bar, then click on the [Password] sub-tab. Enter the current printer password in the [Enter the current printer password:] field.
Page 133: Change Default Language (Print Services On Web, 6030/6050)
Select the required language selection from the pull down list. Click the [Apply] button to save the change, or [Cancel] to undo it. Power the machine off and then on for the change to take effect. 3.16 Change Default Language (Print Services on Web, 6030/6050) Downloaded From ManualsPrinter.com Manuals...
Page 134: Change Default Language (Web Printer Management Tool, 6050A)
3.17 Change Default Language (Web Printer Management Tool, 6050A) Web Printer Management Tool allows the user to change the language displayed when it is started. The language can be changed to English, Italian, French, Spanish, South American Portuguese, German or Russian. Select the [ Configuration] tab on the main navigation bar, then select the [Printer] sub-tab.
Page 135: Chapter 4 Logical Printer Setup And Operation (6030/6050 Only)
Chapter Chapter 0 Logical Printer Setup and Operation (6030/6050 only) Chapter 4 Downloaded From ManualsPrinter.com Manuals...
Page 136: Creating A New Logical Printer
Start the web browser and log in to Print Services on Web. Enter the Administrator mode, and then select the [Print Setup] tab. Chapter 4 Logical Printer Setup and Operation (6030/6050 only) Downloaded From ManualsPrinter.com Manuals...
Page 137 Select the data format for the new logical printer from the [Data format] menu. The selections include [Versatec], [HP-GL], [TIFF], [CALS], and optionally, [PS/PDF]. The logical printers are pre-configured in the factory to their default print settings. These defaults, as well as the options you can select, are defined in the upcoming section "4.2 Defining the Print Settings".
Page 138 To print a list of the logical printer settings, scroll to the bottom of the [Logical printer information] list and click the [Print] button. If required, set up the print parameters following the instructions in section "4.2 Defining the Print Settings". Chapter 4 Logical Printer Setup and Operation (6030/6050 only) Downloaded From ManualsPrinter.com Manuals...
Page 139: Defining The Print Settings
Defining the Print Settings The next step, after creating a logical printer, is to set up the parameters that define how it will process print jobs. These parameters are located at the left side of the screen in the [Print Setup] menus ([Media setting], [Input setting], [Output setting], [Transform], [Pen setting], and [Command setting]).
Page 140: Logical Printer Print Settings
Specifies the media size series for the input and output data, and the media. Size/Media Sets up the input size mapping, and Mapping whether to enable or disable the media mapping. Chapter 4 Logical Printer Setup and Operation (6030/6050 only) Downloaded From ManualsPrinter.com Manuals...
Page 141 [Print Setup] Menu Item Description Format Menu Media setting Media Source Determines whether the paper is to be (continued) fed automatically from a roll or from the (MSI) Multi Sheet Inserter/Manual Feed Unit, and sets up the priority ([Job] or [Controller]).
Page 142 Enables and disables the PS command. HPGL EOP Command Enables and disables the EOP HPGL command. Note Print ranges cannot be set up for TIFF and CALS. Chapter 4 Logical Printer Setup and Operation (6030/6050 only) Downloaded From ManualsPrinter.com Manuals...
Page 143: Media Series
Media Series This parameter sets up the media size series for the input size, output size, and media size. Each item can be set to a different media size series. Settings The settings are as follows. All of the default settings are [ISO A]. Menu Item Description Input size...
Page 144 E30 to A UE30 to UA E30 to B Refer to "9.1 Main Specifications (6030/6050)" for the 6030/6050 and "9.2 Main Specifications (6050A)" for the 6050A for details on the media sizes. Chapter 4 Logical Printer Setup and Operation (6030/6050 only)
Page 145: Size/Media Mapping
Size/Media Mapping Standard size images and user-defined images can be enlarged and reduced to fit standard and user-defined output sizes. This is known as "Size Mapping". It is also possible to specify which roll media is to be used based on the output size.
Page 146 The paper size selected will differ in accordance with the [Media size] parameter set for the Media series. Refer to the section on "Media Series" for further details on paper groups. Chapter 4 Logical Printer Setup and Operation (6030/6050 only) Downloaded From ManualsPrinter.com Manuals...
Page 147 Example When the mapping table is set up as shown below, an image with an input size of A3 will be printed as follows. Media Mapping Input size Output size Media size Size Mapping Size mapping is applied to the image with an input size of A3, which is then enlarged to an A2 output size (enlarged by 141.4%).
Page 148: Media Source
[JOB] The paper tray command in the print data takes priority. [Controller] The setting made on the printer control panel takes priority. The default settings is [JOB]. Chapter 4 Logical Printer Setup and Operation (6030/6050 only) Downloaded From ManualsPrinter.com Manuals...
Page 149: Media Type
Media Type Determines the default media type selection for printing. This setting is valid when a different type of media of the same size is loaded in the printer. [ANY] is set for this under normal circumstances. When the media type specification command is already set up in the job data from the host, the host command has priority.
Page 150: User-Defined Size
Refer to the section on "Media Series" for further details on paper groups. Chapter 4 Logical Printer Setup and Operation (6030/6050 only) Downloaded From ManualsPrinter.com Manuals...
Page 151: Input Option
Input Option Sets up the input image size. Two judgment methods are available for input image size. • Automatic (AUTO) Calculates the coordinates of the input image and automatically determines the nearest media size. • Specify Size Enables the user to manually select the media size of the input image. The media size can be selected from standard sizes and user-defined sizes.
Page 152 [Connect]. For example, in the event of 4A3, 3 will be set for the [Connect]. Refer to the section on "Media Series" for further details on paper groups. Connect = 3 Chapter 4 Logical Printer Setup and Operation (6030/6050 only) Downloaded From ManualsPrinter.com Manuals...
Page 153: Input Size Margin
Input Size Margin Specifies the top, bottom, left, and right margin settings for determining input sizes. Plus (+) values represent margins outside of the media size, and minus (–) values represent margins inside the media size. The size that includes (excludes) these margins is established as the input judgment size.
Page 154 × printing is performed on A2 paper to –10 mm A2: 410 × (420 594), a margin will be located at the top, bottom, left and right. Chapter 4 Logical Printer Setup and Operation (6030/6050 only) Downloaded From ManualsPrinter.com Manuals...
Page 155: Plot Area
Plot Area Enables the print range (the plot area) to be specified based on the input image information. The plot area can be set up so that the image prints in the center of the media (Auto Layout) or is offset (Set Offset Value). If part of the image overlaps the margin when offset is specified, it will be cut off.
Page 156 For example, if the following settings have been made, an image with an A2 output size will be printed with an offset of 20 mm in the X direction and 10 mm Chapter 4 Logical Printer Setup and Operation (6030/6050 only) Downloaded From ManualsPrinter.com Manuals...
Page 157 in the Y direction. OFFSET Size – – 999 to 999) 999 to 999) –10 Descriptions of Area Mode The area modes are described below. ADAPTED The data range of the input image is set as the print range (see Fig.1). FIXED (HP-GL) The range that encloses the maximum coordinate of the input image and the coordinates that represent the starting...
Page 158 Fig.1. (ADAPTED) Input image (0,0) Offset Output image Auto Layout: [YES] Auto Layout: [NO] Fig.2. (FIXED) (+X1,+Y1) Input image Offset (0,0) Output image Auto Layout: [YES] Auto Layout: [NO] Fig.3. (IP AREA and IW AREA) The area specified with the [IP Command] or [IW Command].
Page 159 Fig.4. (FIRST) (0,0) Output image Offset Auto Layout: [YES] Auto Layout: [NO] Fig.5. (FIRST ) (0,0) Input image Output image 4.3 Logical Printer Print Settings Downloaded From ManualsPrinter.com Manuals...
Page 160: Priority
Sets one of the following as the printing priority. The default setting is [NORMAL]. [LOW] Low printing priority [NORMAL] Normal (standard) printing priority [HIGH] High printing priority Chapter 4 Logical Printer Setup and Operation (6030/6050 only) Downloaded From ManualsPrinter.com Manuals...
Page 161: Title Block
Title Block The setting determines whether or not to rotate images 180 degrees. This setting is used to change the image orientation to ensure correct folding. Settings The available settings are as follows. Menu Item Description Media Size Determines whether or not to rotate images for each media size.
Page 162: Split Drawing
Determines whether or not a page number will be printed. printing The page number will be printed in the format [present page number:total number of pages]. The default setting is [Off]. Chapter 4 Logical Printer Setup and Operation (6030/6050 only) Downloaded From ManualsPrinter.com Manuals...
Page 163 Item Description Page margin Determines whether or not the page margin will be present, and sets the margin where the pages are joined within a range of 0 to 90 mm. The default settings is [0 mm]. Alignment mark Determines whether or not to print positioning marks. The printing default setting is [OFF].
Page 164: Message Option
Determines whether or not to print error messages. The default setting is [ON]. Label Message Determines whether or not to print label messages. The default setting is [OFF]. Chapter 4 Logical Printer Setup and Operation (6030/6050 only) Downloaded From ManualsPrinter.com Manuals...
Page 165 Menu Item Description Date Message Determines whether or not to print date messages. The default setting is [OFF]. The date format is [Year/Month/Day Hour:Minutes]. Example: [2006/01/02 14:56] Display Position Sets up the location where the message(s) will be printed. [Upper left] Prints the message(s) at the top left- hand corner of the page.
Page 166: Printed Copy
[JOB] The copy count command in the job data takes priority. [Controller] The setting made on the printer control panel takes priority. The default setting is [JOB]. Chapter 4 Logical Printer Setup and Operation (6030/6050 only) Downloaded From ManualsPrinter.com Manuals...
Page 167: Output Option
Output Option Sets up the output size. The following two judgment methods are available for output image size. • Automatic (AUTO, OTHER, MIX, MIX2) Determines the most suitable output size based on the input size and the size mapping table. It also determines the roll media size to use based on the output size and the media mapping table (or automatically.) •...
Page 168 [Margin] parameter is set to [ALL] or [LONG]. Trail Margin Sets the bottom margin in a range from 0 to 999 mm when the [Margin] parameter is set to [ALL] or [LONG]. Chapter 4 Logical Printer Setup and Operation (6030/6050 only) Downloaded From ManualsPrinter.com Manuals...
Page 169 • Media Size In the case of [AUTO] Output in a size that is the standard shape increased in a multiple of integers. Input image that is longer In the case of [OTHER] than the standard size The same size as the input image is output.
Page 170: Size Recognition
In the case of an input image that increased in a multiple of is longer than the standard size integers (example: 420 × 650mm) (example 2A2: 420 × 1,188mm) Output image Settings Chapter 4 Logical Printer Setup and Operation (6030/6050 only) Downloaded From ManualsPrinter.com Manuals...
Page 171 The settings for this function are as follows. Menu Item Description Size Sets up the size recognition priority mode. Recognition The default value is [Standard long size output]. [Standard long size Outputs images that are within the A0 output] size, but exceed the standard size, on one size larger standard shape paper.
Page 172: Color Option
[DISABLE] Draws all lines with the black pen. Lines are not visible when they are drawn on a black background. The default setting is [ON] for HP-GL; [OFF] for Versatec. Chapter 4 Logical Printer Setup and Operation (6030/6050 only) Downloaded From ManualsPrinter.com Manuals...
Page 173: Transform
Transform Enables or disables the auto scale (automatic enlargement/reduction), mirror image, and 90-degree rotation functions. Auto Scale Input image Output image Mirror Image Input image Output image 4.3 Logical Printer Print Settings Downloaded From ManualsPrinter.com Manuals...
Page 174 Outputs the image in the normal manner. This setting is only valid when the [Media Size] parameter of [Input Option] is set to anything other than [Auto]. Chapter 4 Logical Printer Setup and Operation (6030/6050 only) Downloaded From ManualsPrinter.com Manuals...
Page 175: Define Single Pen
Define Single Pen Defines the width, color, end style, and joint style pen attributes for HP-GL data. Click the [Change] button to edit the attributes of a pen. The screen below will display. Click [Apply] to save your changes. Settings The settings for this function are as follows.
Page 176 Refer to the illustrations on the next page for more details. This setting is only valid for HP-GL and HP-GL/2 EA, EP, ER, FP, RA, RR, and PE. End style Chapter 4 Logical Printer Setup and Operation (6030/6050 only) Downloaded From ManualsPrinter.com Manuals...
Page 177 SQUARE The normal method for ending lines. ROUND Line width Rounds off both ends of the line with a half radius of the line width. Half the line width Half the line width EXTEND Extends both ends by half the line width. Line width Half the line width Half the line width...
Page 178 MITERED/BEVELED Extends the joint by the length calculated from the line width and Miter Limit, and connects the top. Chapter 4 Logical Printer Setup and Operation (6030/6050 only) Downloaded From ManualsPrinter.com Manuals...
Page 179: Define Multi Pen
Define Multi Pen Sets up the line width, color, end style, and joint style pen attributes for HP-GL data for multiple pens. The same parameters will be set for all other pen numbers within the specified range. Settings The settings for this function are as follows. Menu Item Description Pen No.
Page 180: Pen Option
Menu Item Description Enlarge/reduce [ENABLE] Changes the pen width based on the pen width enlargement/reduction ratio. [DISABLE] The pen width remains unchanged. The default setting is [DISABLE]. Chapter 4 Logical Printer Setup and Operation (6030/6050 only) Downloaded From ManualsPrinter.com Manuals...
Page 181: Emulation
Emulation Selects the processing language for the HP-GL format only. Settings The settings for this function are as follows. Menu Item Description Emulation Sets the processing language at either [HP-GL] or [HP-GL/ The default setting is [HP-GL]. 4.3 Logical Printer Print Settings Downloaded From ManualsPrinter.com Manuals...
Page 182: Ps Command
The available settings are as follows. Menu Item Description PS command [DO NOT IGNORE] Enables the PS command. [IGNORE] Disables the PS command. The default setting is [DO NOT IGNORE]. Chapter 4 Logical Printer Setup and Operation (6030/6050 only) Downloaded From ManualsPrinter.com Manuals...
Page 183: Eop Command
EOP Command Enables and disables the EOP command for HP-GL data only. Settings The settings for this function are as follows. The default value for all parameters is [Enable]. Menu Item Description SP:Pen0 Enables or disables the SP:Pen0 command. PG:Adv Page Enables or disables the Adv Page command.
Page 184: Vcgl Pen Style (Vcgl Define Pen)
[SQUARE]. Refer to "End style" for further details. Dashed line Sets broken line processing to [WRAP] or [NO WRAP]. style The default setting is [NO WRAP]. Dashstyle Chapter 4 Logical Printer Setup and Operation (6030/6050 only) Downloaded From ManualsPrinter.com Manuals...
Page 185 Example Broken line style NO WRAP Each dot represents the start of the broken line. Lines printed with the use of the broken line style shown in the example will be printed as a non-broken line, as shown in the illustration on the left. This is due to the fact that the dot appears before the line is broken, and this constitutes the starting point for printing another line.
Page 186: Vcgl Pen Width
1 = 0.0635 mm. The actual width of the line will be n 0.0635, with the line width set to n. The default setting is [2]. Text may not print clearly if the line width is set to [1]. Chapter 4 Logical Printer Setup and Operation (6030/6050 only) Downloaded From ManualsPrinter.com Manuals...
Page 187: Vrf Define Pen (Define Single Pen)
VRF Define Pen (Define Single Pen) Sets the pen attributes for VRF data only. Click the [Change] button to define the attributes for a pen. The VRF Define Pen menus will display on the right side of the screen. Settings The settings for this function are as follows.
Page 188 Although it is also possible to set the [Width] from Print Services on Web, the width data included in the VRF data take priority, and any changes on the Print Services on Web screen will have no effect on the output. Chapter 4 Logical Printer Setup and Operation (6030/6050 only) Downloaded From ManualsPrinter.com Manuals...
Page 189: Vrf Define Multi Pen
VRF Define Multi Pen Sets the pen attributes for multiple pens for VRF data only. The same parameters will be set for all other pen numbers within the specification range. Settings The settings for this function are as follows. Menu Item Description Pen No.
Page 190: Tiff Option
Uses the resolution embedded in the TIFF data. [CONTROLLER]Uses the resolution set here. Controller Sets the resolution within a range of 30 to 3000 (dpi) when Resolution the [CONTROLLER] parameter has been specified. Chapter 4 Logical Printer Setup and Operation (6030/6050 only) Downloaded From ManualsPrinter.com Manuals...
Page 191: Cals Option
CALS Option Determines whether to enable or disable the [Rotate] command for CALS data only. Settings The settings for this function are as follows. Menu Item Description Specify Output [ENABLE] Enables the [Rotate] command. Direction [DISABLE] Disables the [Rotate] command. The default setting is [DISABLE].
Page 192: Ps/Pdf Option
Print data is placed inside the margins. [Extend] No margins are added. Images will be printed to the edge of the page. Chapter 4 Logical Printer Setup and Operation (6030/6050 only) Downloaded From ManualsPrinter.com Manuals...
Page 193: Logical Printer Operations
Logical Printer Operations This section explains the procedures for performing the following using Print Services on Web. • Selecting the Media Type • Using Media Other Than the Default Series • Changing Output Roll Media for an Entire Job • Reduction and Enlargement Using Size Mapping •...
Page 194: Selecting The Media Type
If a media other than the specified type is loaded after this setting is made, a [No Paper] error will be triggered. Refer to "4.3 Logical Printer Print Settings" for details. Chapter 4 Logical Printer Setup and Operation (6030/6050 only) Downloaded From ManualsPrinter.com Manuals...
Page 195: Using Media Other Than The Default Series
• Refer to the "Media Series" section of "4.3 Logical Printer Print Settings" for details on available functions. • Refer to "9.1 Main Specifications (6030/6050)" for the 6030/6050 and "9.2 Main Specifications (6050A)" for the 6050A for details on the media sizes for each media group.
Page 196: Changing Output Roll Media For An Entire Job
A1 roll media. Logical printer [PLT01H] specified Job1 Output on the A2 roll media Logical printer [PLT02H] specified Job2 Output on the A1 roll media Rotated by 90 degrees Chapter 4 Logical Printer Setup and Operation (6030/6050 only) Downloaded From ManualsPrinter.com Manuals...
Page 197: Reduction And Enlargement Using Size Mapping
Reduction and Enlargement Using Size Mapping Reduction and enlargement can be performed using the size mapping table. The size mapping table establishes relationships between input image sizes and output image sizes. It enables users to enlarge or reduce prints automatically. The size mapping table is set up using the logical printer’s [Size/media mapping] selection.
Page 198: Printing Long Documents
• All output is carried out on roll media when [OTHER] has been selected. Cut sheet cannot be used. Chapter 4 Logical Printer Setup and Operation (6030/6050 only) Downloaded From ManualsPrinter.com Manuals...
Page 199: Print Services On Web: Job And Log
Print Services on Web: Job and Log The Print Services on Web [Job and Log] tab enables the user to perform the following. • Display the Print Queue • Cancel and Change the Priority of Jobs • Manage the Job and Error Logs •...
Page 200 Printing in progress. Priority Displays [High], [Normal] or [Low] as the priority. Document Displays the name of the document. Name [---] is displayed when the name is unknown. Chapter 4 Logical Printer Setup and Operation (6030/6050 only) Downloaded From ManualsPrinter.com Manuals...
Page 201 Displayed Description Item Printer Name Displays the name of the destination logical printer. [---] is displayed when the name is unknown. Size Displays the size of the job in KB. Change Job Changes the priority of or cancels a job. (On the Administrator page only) 4.5 Print Services on Web: Job and Log Downloaded From ManualsPrinter.com Manuals...
Page 202: Cancel And Change The Priority Of Jobs
Procedure Start Print Services on Web, log on as Administrator, and select the [Job and Log] tab. Refer to "2.3 Print Services on Web (6030/6050)" for details on starting up Print Services on Web. Select [Job not completed]. A list of all jobs that are printing and queued will display on the right side of the screen.
Page 203 To reduce the size of the list, set up the [Logical printer] and [Logical printer number] fields, and then click the [Update] button. Set the [Update time] to automatically update the list, if desired. Click the [Change] link located on the right side of the job that you want to cancel or change.
Page 204: Manage The Job And Error Logs
It is only possible to display a list of jobs on the User page. All other operations must be carried out on the Administrator page. Job log and error log management also can be performed from the printer control panel. Refer to "5.5 Managing the Job and Error Logs (6030/6050 only)" for more information. Job Log The job log is a record of all completed print jobs.
Page 205 Select [Job Log] from the [Log list] menu. A list of processed jobs will display on the right side of the screen. To display a subset of the logged print jobs: • Enter a range in the [Job number] fields, and then click the [Update] button - or - •...
Page 206 Chapter 4 Logical Printer Setup and Operation (6030/6050 only) Downloaded From ManualsPrinter.com Manuals...
Page 207 Select [Job log] from the [Log list] menu. A list of completed jobs will display on the right side of the screen. To display a subset of the logged print jobs, enter a range in [Job number] or specify the period in the [Print log from:] fields, and then click the [Update] button.
Page 208 Select [Job Log] from the [Log list] menu. A list of log information will display in the right pane. Chapter 4 Logical Printer Setup and Operation (6030/6050 only) Downloaded From ManualsPrinter.com Manuals...
Page 209 Click [Change settings]. The [Job log setup] screen will display. Select [ON] as the [Auto Print Setup] selection, and then click [Apply]. The job log will print automatically whenever sufficient job log entries accumulate. Delete the Job Log Start Print Services on Web, log on as Administrator, and display the [Job and Log] tab.
Page 210 Chapter 4 Logical Printer Setup and Operation (6030/6050 only) Downloaded From ManualsPrinter.com Manuals...
Page 211 Click the [Delete log] button. A confirmation popup will display. Select the [OK] button to delete the job log, or [Cancel] to retain the log. Save the Job Log Start Print Services on Web, log on as Administrator, and display the [Job and Log] tab.
Page 212 Chapter 4 Logical Printer Setup and Operation (6030/6050 only) Downloaded From ManualsPrinter.com Manuals...
Page 213 Further define the job log, if necessary, using the [Print log from], [Job number], [Date], and [Display] selections, and then click the [Save into file] link. The job log will be saved in a comma-separated value (CSV) format, and displayed as in the figure below. Display the Error Log The Error Log is a record of information about the errors that occurred during job processing.
Page 214 The procedures for saving, deleting, and printing the error log(s) are the same as those for managing the job log(s). Refer to the relevant job log procedure when you need to change or save the error log data. Chapter 4 Logical Printer Setup and Operation (6030/6050 only) Downloaded From ManualsPrinter.com Manuals...
Page 215: Print Services On Web: Status
To access Help, click the [?] button in the upper, right corner of the screen. Display Printer Status This function displays the status of the 6030/6050 Wide Format Printer and Copier/Printer. Procedure Start Print Services on Web and display the [Status] tab on either the User page or the Administrator page.
Page 216 • Meter 2: The total length (in feet and meters) of media printed until now • Meter 3: The total number of stamp prints made until now IOT Status Details Chapter 4 Logical Printer Setup and Operation (6030/6050 only) Downloaded From ManualsPrinter.com Manuals...
Page 217 System error A system error has occurred in the printer. Switch off the printer power, and then switch it on again. If the problem does not recover, contact your Xerox Service Representative. 4.6 Print Services on Web: Status Downloaded From ManualsPrinter.com Manuals...
Page 218: Start And Stop Job Reception, Printing, And The Print Service
To start or stop printing, click the [Print] [Start] or [Stop] button. To start or stop the server, click the [Print service] [Start] or [Stop] button. Chapter 4 Logical Printer Setup and Operation (6030/6050 only) Downloaded From ManualsPrinter.com Manuals...
Page 219: Print Services On Web: Tools
These procedures can only be performed from the Administrator mode. Test printing also can be performed from the printer control panel. Refer to "5.4 Test Printing (6030/6050 only)". • The Print Services on Web Help function provides step-by-step instructions for performing the tasks described below. It also provides lists and descriptions of the items and fields that appear on the screen.
Page 220: Print A Diagnostic Report
Specify the inclusive report dates using the [Range (Date: YYMMDD):] field, and then click [Save]. A dialog box will display. You may choose to open and view the report or save it. Chapter 4 Logical Printer Setup and Operation (6030/6050 only) Downloaded From ManualsPrinter.com Manuals...
Page 221: Manual Feed Printing
Procedure Set [Media Source] for the logical printer to [Manual]. Send the print job to the 6030/6050 Wide Format Printer or Copier/ Printer. The following message will display on the printer control panel if there is no media in the (MSI) Multi Sheet Inserter/Manual Feed Unit.
Page 222 Chapter 4 Logical Printer Setup and Operation (6030/6050 only) Downloaded From ManualsPrinter.com Manuals...
Page 223: Chapter 5 Additional Operations From The Printer Menu
Chapter Chapter 0 Additional Operations from the Printer Menu Chapter 5 Downloaded From ManualsPrinter.com Manuals...
Page 224: Introduction
Introduction The printer control panel’s menus enable the user to perform the following major tasks: (On the 6030/6050 Wide Format) • Set up the system parameters using the [SYSTEM PARAMETERS] submenu. • Set up the communication parameters using the [PORT SETTING] submenus.
Page 225: Printer Control Panel Menu (6030/6050)
< > key, after pressing the <Set> key to accept the previous selection. It is recommended that the procedures covered in this chapter be performed using Print Services on Web. 5.2 Printer Control Panel Menu (6030/6050) Downloaded From ManualsPrinter.com Manuals...
Page 226 [Network Port/Set] Menu Level 1 Level 2 Level 3 Level 4 Level 5 Level 6 SYSTEM Set Date Set Date PARAMETER YY/MM/DD hh: mm AUTO ROLL Roll Tray Roll Tray Tray Roll Tray Roll SPA PAPER WIDTH SPA PAPER WIDTH Sp A1 Sp A1 Sp A2...
Page 227 E-Net Address (display only) Dynamic Routing Dynamic Routing Static Routing Static Routing Dest. Address xxx.xxx.xxx.xxx ROUTING TABLE Level 7 Router Address *xxx.xxx.xxx.xxx ROUTING ROUTING TABLE TABLE PRINT SET: to Print 5.2 Printer Control Panel Menu (6030/6050) Downloaded From ManualsPrinter.com Manuals...
Page 228 Level 1 Level 2 Level 3 Level 4 Level 5 Level 6 PORT SERIAL Handshake Handshake SETTING XON/XOFF HARDWARE ENQ-ACK SOFTWARE (ENQ-ACK and SOFTWARE only with HPGL) Default Parser HPGL Baud Rate Baud Rate 1200 2400 4800 9600 19200 Parity Parity NONE EVEN...
Page 229 (display only) The [Starting day to ending day] parameter for log management is specified in the YYMMDD format; (YY: 00 to 99, MM: 01 to 12, DD: 01 to 31) 5.2 Printer Control Panel Menu (6030/6050) Downloaded From ManualsPrinter.com Manuals...
Page 230 [Print Setup] Menu The Print Setup menu should be used immediately after loading new media or changing the type and/or size of media in the media drawers or the bypass (MSI). Level 1 Level 2 Level 3 Level 4 Level 5 Level 6 PRINT MEDIA...
Page 231: Printer Control Panel Menu (6050A)
Printer Control Panel Menu (6050A) The following is a list of the menus and submenus which can be accessed by pressing the <Menu> key and placing the printer in the offline mode. As a reminder, the following buttons are used to navigate the printer control panel menus.
Page 232 [System Settings] Menu *xxx.xxx.xxx.xxx System Settings TCP/IP IP Address IP Subnet Mask *xxx.xxx.xxx.xxx IP Gateway *xxx.xxx.xxx.xxx *Enable DHCP *Disable RARP/BOOTP *Enable *Disable Date/Time *MM/DD/YYYY HH:MM Timers Power *5-240 Min. Management/ Low Power Power *5-240 Min. Management/ Sleep Mode Chapter 5 Additional Operations from the Printer Menu Downloaded From ManualsPrinter.com Manuals...
Page 233 [Utilities] Menu Utilities *Printer Test Print Configuration *Printer Settings *Pen Palettes *All Meter 1 Billing Meters #### Meter 2 #### Shut Down *Shut Down *Restart 5.3 Printer Control Panel Menu (6050A) Downloaded From ManualsPrinter.com Manuals...
Page 234 [Print Setup] Menu The Print Setup menu should be used immediately after loading new media or changing the type and/or size of media in the media drawers or the bypass (MSI). Print Setup Roll *1,2 *Enable Tray Roll *3,4 *Disable Bypass *Enable *Disable...
Page 235: Test Printing (6030/6050 Only)
Press the < > key once it has been set. TEST PLOT Press the <Set> key when [SET: to Print.] is SET : to Print. displayed. The test data will be printed. 5.4 Test Printing (6030/6050 only) Downloaded From ManualsPrinter.com Manuals...
Page 236: Managing The Job And Error Logs (6030/6050 Only)
When [SETTING] is selected SETTING 1. Select [Auto Mode] with the use of the Auto Mode < > and < > keys, and then press the 5.5 Managing the Job and Error Logs (6030/6050 only) Downloaded From ManualsPrinter.com Manuals...
Page 237 The job log will be printed. When [CLEAR] is selected CLEAR Press the <Set> key when [SET: to Clear.] SET : to Clear. is displayed. The job log will be deleted. 5.5 Managing the Job and Error Logs (6030/6050 only) Downloaded From ManualsPrinter.com Manuals...
Page 238: Error Log (6030/6050 Only)
Error Log (6030/6050 only) This section explains the procedures for printing and clearing the error log. Procedure MENU Press the < > key with [JOB LOGGING] JOB LOGGING displayed. JOB LOGGING Display the [ERROR LOG] with the use of ERROR LOG the <...
Page 239 JobNo Data&Time Task Name ErrNo ErrorLevel Error Log Error Data 02/04/17 15:49:30 OUTPUT ERROR PAGE MEMORY OVERFLOW NO-PAGE-MEMORY Status from PrintMgr 02/04/22 20:38:05 HP PARSER WARNING UNRECOGNIZED_COMMAND 5.5 Managing the Job and Error Logs (6030/6050 only) Downloaded From ManualsPrinter.com Manuals...
Page 240: Reprinting (6030/6050 Only)
Reprinting (6030/6050 only) This function reprints the file that was most recently printed. The copy quantity (1 to 99) also can be specified. Reprinting can not be performed if a copy job has been performed after the print job. In order for reprinting to work, a job must be saved in memory.
Page 241: Billing Meter Confirmation (6030/6050)
1], [Meter 2], or [Meter 3]) using the < > and < > keys, and then press the < > key. METER 1 The selected meter and the current reading 986754 will display. 5.7 Billing Meter Confirmation (6030/6050) Downloaded From ManualsPrinter.com Manuals...
Page 242: Billing Meter Confirmation (6050A)
Billing Meter Confirmation (6050A) This feature displays the billing meters on the printer control panel. Quantities of up to nine digits can be displayed. Menu Item Description METER 1 Displays the total area of media printed (in square feet or meters). METER 2 Displays the total length of media printed (in feet and meters).
Page 243: Print Setup Menu
Print Setup Menu This section explains the items which can be set up from the [PRINT SETUP] Menu on the printer control panel. Menu Item Description Media Sets up the type, size, weight, and other parameters for the media that are loaded in the machine.
Page 244 Media Type Roll1 Bond Roll2 Vellum Roll3 Film Roll4 Bypass Weight Light Ordinary Heavy Series Sp. A-1 Sp. A-2 ANSI Arch. Trim The media Size Series and sizes that can be set up are as follows. Size Series Eligible Media ×...
Page 245 Size Series Eligible Media × SP. A-2 series SP. A-1 (620 871 mm) SP. A-1 roll media (620 mm wide) × SP. A-2 (435 620 mm) SP. A-2 roll media (435 mm wide) ARCH 36", 24", 18", 12", 9" ANSI 34", 22", 17", 11", 8.5"...
Page 246 The [PRINT SETUP] menu will display. The [NETWORK/PORT SET] menu screen will display if the < > key is pressed. < > key Press the < > key. The submenu items will display. Print Setup Media < > < > key Press the <...
Page 247 < > key Press the < > key. The specified value will display. Media / Roll1 Type : Bond < > < > key Change the setting with the use of the < > and < > keys. Media / Roll1 Type : Film <Set>...
Page 248: Automatic Cut Using The Printer Control Panel
5.10 Automatic Cut Using the Printer Control Panel This section describes how to cut the lead edge of the roll media. Procedure Select [Media] from the menu displayed on Print Settings the printer control panel. Media < > key Press the < > key. The level from which the desired media is to Media be selected will be displayed.
Page 249 Press the < > key to return to the higher level. 5.10 Automatic Cut Using the Printer Control Panel Downloaded From ManualsPrinter.com Manuals...
Page 250 Tray This normally is set to [Auto] and should not be changed by the user. Consult your Xerox Service Representative before changing this setting. Fuser This normally is set to [Auto] and should not be changed by the user. Consult with your Xerox Service Representative before changing this setting.
Page 251: Chapter 6 Ethernet Print Service (For Unix)
Chapter Chapter 0 Ethernet Print Service (for UNIX) Chapter 6 Downloaded From ManualsPrinter.com Manuals...
Page 252: Overview Of The Ethernet Print Service
This section explains how to set up the ftp and lpr commands and their formats. The file to be printed should be in a data format that the Xerox 6030/6050 Wide Format supports. Sending a file with a data format that is not supported will result in a print error.
Page 253: 6.2 Registering The Xerox 6030/6050 Wide Format Printer System
SunOS 5.X In the case of SunOS 5.X, register the IP address and host name of the Xerox 6030/6050 Wide Format printer in the /etc/hosts file that defines the printers connected to the network.
Page 254: Registering The Remote Printer
Xerox 6030/6050 Wide Format printer system. Refer to the "Main Printing Functions" section in "2.1 Overview of the 6030/ 6050/6050A Wide Format Printer" for logical printer. SunOS 5.X For SunOS 5.X, register the remote printer using the lpadmin command.
Page 255 = /usr/lpd/bsdlong rq = PLT20H device = dplt20hdplt20h: backend = /usr/lpd/rembak Be sure to specify a logical printer prepared in the 6030/6050 Wide Format printer system using rq. • Starting the Print Queue After finishing the settings, start the print queue using the qadm command.
Page 256: Registering The Xerox 6050A Wide Format Printer System
Registering the Xerox 6050A Wide Format Printer System To print from the Xerox 6050A Wide Format printer system, the 6050A should be registered on the TCP/IP network. Host System Registration When the network information is managed by a name service such as NIS or DNS, the IP address and host name must be registered there.
Page 257: Registering The Remote Printer
In the example below, the 6050A with the host name oklahoma is registered. In contrast to the 6030/6050 with its plt00h, etc., the queue names for the 6050A with the Accxes controller are always given the name of [raw]. #lpadmin -p oklahoma -s oklahoma!raw If csh is used, enter "...
Page 258 = /usr/lpd/bsdlong rq = PLT20H device = dplt20hdplt20h: backend = /usr/lpd/rembak Be sure to specify a logical printer prepared in the 6030/6050 Wide Format printer system using rq. • Starting the Print Queue After finishing the settings, start the print queue using the qadm command.
Page 259: Printing Using The Ftp Command (6030/6050 Only)
Connected to 6050WF. 220 6050 Wide Format FTP server ready Name (6050WF:ftpusr): Log on to the Xerox 6030/6050 Wide Format . Enter a user name (example: ftpusr) pre-registered in Xerox 6030/6050 Wide Format . You are prompted to enter a password.
Page 260 Enter the password of the user logged in at Step If the user information registered in the Xerox 6030/6050 Wide Format matches the logged-in user password, the login acceptance message is displayed. Password: 230 User logged in ftp> The password of the user (ftpusr) is ftpusr at shipping.
Page 261 Specify the end. Enter the bye subcommand. A message indicating that ftp command has completed will be displayed. ftp> bye 221 Bye...see you later 6.4 Printing Using the ftp Command (6030/6050 only) Downloaded From ManualsPrinter.com Manuals...
Page 262: Other Subcommands
Displays directory; will display logical printers set from the control panel. If nothing is specified in the Xerox 6030/6050 Wide Format , only the logical printer at address 00 is displayed. Displays directory; will display logical printers set from the console panel.
Page 263: Message List
Control connection read error Status: A control connection error occurred in the FTP command wait status. Therefore, the connection was disconnected. Action: For another transfer, establish the connection again. 6.4 Printing Using the ftp Command (6030/6050 only) Downloaded From ManualsPrinter.com Manuals...
Page 264 Status: Cannot accept data transfer because the system is overloaded. Action: Check the system for a media-out or media jam error. Wait a few moments and try again. If the error occurs frequently, restart the Xerox 6030/6050 Wide Format .
Page 265 Action: Wait a few moments and try again. Local resource failure: please start queuing Status: Cannot accept file transfer because queuing is stopped. Action: Start queuing and execute printing again. 6.4 Printing Using the ftp Command (6030/6050 only) Downloaded From ManualsPrinter.com Manuals...
Page 266 Login failed Status: The user name and password do not match. Action: Log in again with the correct user name and password. No file found or invalid directory or permission problem Status: Failed to open the directory by the LIST command. Action: Wait a few moments and transfer the command again.
Page 267 Status: A user name or password was not specified by the USER or PASS command, or various commands were transferred without login. Action: Log in with a registered user name and password and try again. 6.4 Printing Using the ftp Command (6030/6050 only) Downloaded From ManualsPrinter.com Manuals...
Page 268: Printing Using The Lp/Lpr Command
Specify the number of copies by entering a numeric value from 1 to 99 for the 6030/6050 or 1 to 199 for the 6050A. If more than 100 for the 6030/6050 or more than 1000 for the 6050A is specified, an error message is displayed and the specification is canceled.
Page 269 Usage Examples (6030/6050) The printing procedure using the lpr command is as explained below. Example 1:To print one copy of the file [drawa.hpgl] by logical printer [plt00h]. % lpr -Pplt00h drawa.hpgl Example 2:To print two copies each of the files [drawb.hpgl] and [drawc.hpgl] by logical printer plt00h.
Page 270 Usage Examples (6050A) The printing procedure using the lpr command is as explained below. Example 1:To print one copy of the file [drawa.hpgl] by logical printer [raw]. % lpr -Praw drawa.hpgl Example 2:To print two copies each of the files [drawb.hpgl] and [drawc.hpgl] by logical printer [raw].
Page 271: Printing (Lp Command) (For Sunos 5.X)
Specify the number of copies by entering a numeric value from 1 to 99 for 6030/ 6050 and 1 to 999 for 6050A. If 100 or more is specified for the 6030/6050 or if more than 1000 is specified for the 6050A, an error message is displayed and the specification is canceled.
Page 272: Status Display (Lpq Command)
Example 2:Display the status of a file transferred to logical printer [plt01h] ([lpq -P oklahoma] for 6050A). When the transfer of the [drawd.hpgl] file to the Xerox 6030/6050/6050A Wide Format is completed, the following message will be displayed. % lpq -Pplt01h...
Page 273 Format. cosmos: sending to oklahoma Rank Owner Job Files Total Size indicates the client status. The job ID for the client and the job ID for the Xerox 6030/6050/6050A Wide Forma are assigned separately. 6.5 Printing Using the lp/lpr Command...
Page 274: Cancel (Lprm Command)
Specify the job ID of the job to be canceled. The status display command [ lpq ] displays job IDs. If this is omitted, all print jobs are canceled. Job IDs on the Xerox 6030/6050 Wide Format side and the client side are allocated separately.
Page 275 Example 2:Displays the status of logical printer [plt01h] and the canceling of job ID [123] This print job cannot be canceled because it is already in progress. % lpq -Pplt01h Job ID Sent By Status Prior. Document Name Size(KB) williams Printing Normal drawa.hpgl...
Page 276 Example 4:Displays the status of logical printer [plt01h] and the canceling of job ID [416] in the client queue If the file transfer to the Xerox 6030/6050 Wide Format completes before the job in the client queue is canceled, the print job cannot be canceled. Display the Xerox 6030/6050 Wide Format print status, check the job IDs of the logical printer, and cancel the print job again.
Page 277: Message List (6030/6050 Only)
Message List (6030/6050 only) This section explains messages that may be displayed during printing using the lpr command. These messages depend on the system because they are output from the client workstation. Cannot create /usr/spool/pltXXX/.seq Status: The lpd daemon on the client failed to create a control file.
Page 278 PLTXX can not dequeue Status: Failed to delete a job from logical printer PLTXX on the print service side. Action: Check by the lpq command whether the specified job has already changed from the wait status in the queue to the processing status. connection busy Status: Failed to establish connection for data transfer.
Page 279: Chapter 7 Maintenance
Chapter Chapter 0 Maintenance Chapter 7 Downloaded From ManualsPrinter.com Manuals...
Page 280: Loading Toner
Loading Toner Load no more than one cartridge of toner when the message "Add Black Toner" first appears on the printer control panel. Observe the following precautions when handling the toner. • Handle the toner carefully to avoid spilling it on your clothing or around the machine.
Page 281 Take the toner cartridge out of the package and prepare it for loading. Shake the toner cartridge well to ensure that the toner will dispense properly. Open the lid of the toner supply port. Insert the left side notch, located at the bottom of the toner cartridge, into the end of the toner supply port.
Page 282 Slide the toner supply lever back and remove the cartridge. Close the lid on the toner supply port. • If the toner splashes around the toner supply port, clean the area after the loading is completed. • Toner may adhere to the bottom of t one r c ar tr i dg e.
Page 283: Chapter 8 Problem Solving
Chapter Chapter 0 Problem Solving Chapter 8 Downloaded From ManualsPrinter.com Manuals...
Page 284: Check The Control Panel(S)
Check the Control Panel(s) When a machine failure is suspected, for example, when a print cannot be made or the image quality is defective, first check for error messages or error codes on the printer control panel. When an error code is displayed, press the < > and < > keys on the printer control panel at the same time.
Page 285: Poor Image Quality
Poor Image Quality Perform the following corrective measures if the copies or prints display one of the image quality defects listed below. Image Quality Defect Corrective Measure The print displays Verify that the image density setting is correct. Check the quality of the original. excessive background •...
Page 286: Other Problems
Other Problems Follow the instructions provided in the table to recover from the errors which are listed. Error Recovery Nothing is displayed on the • Verify that the machine is connected to a printer control panel. correctly rated power supply, that the power plug is plugged in, and that the power switches and the circuit breaker switch are in the On positions.
Page 287: Printer Troubleshooting
Refer to the "Input Size Margin" section of "4.3 Logical Printer Print Settings" for details on available functions. No paper error occurs even when paper has been set in place. (6030/6050 only) There is a chance that the paper actually set in place differs from the settings made in either [Media Mapping], [Media Type] or [Media Series].
Page 288 [Disable]. The [White Mode] is valid for HP-GL and Versatec data only. Refer to the "Color Option" section of "4.3 Logical Printer Print Settings" for details on available functions. Chapter 8 Problem Solving Downloaded From ManualsPrinter.com Manuals...
Page 289: Jams In The Feeder (Roll Media)
Jams in the Feeder (Roll Media) Media jams in the roll feeder(s) are caused by incorrect media loading methods and defects in the media feeding mechanism. Reload the media according to the following procedure. Procedure Open the media tray. Rewind the media on the roll from which the jam has occurred by rotating it toward you.
Page 290 Lift the lock lever located in the middle at the back of the scanner document table, and then close the document table (6030/ 6050 only). Chapter 8 Problem Solving Downloaded From ManualsPrinter.com Manuals...
Page 291: Jams In The Printer And Ejection Port
Jams in the Printer and Ejection Port Remove media jams from the printer and ejection port following the instructions below. Procedure Lift up the lever located on the left-hand side of the output unit. Use both hands to lift up the top of the unit. The top of the unit cannot be lifted if the scanner's lock has been released.
Page 292 Pull the green stopper to the front. Grasp the document table (6030/6050 only) with both hands and gently but firmly lower it into place. • Ensure that the weight of the...
Page 293: Chapter 9 Specifications
Chapter Chapter 0 Specifications Chapter 9 Downloaded From ManualsPrinter.com Manuals...
Page 294: Main Specifications (6030/6050)
Main Specifications (6030/6050) Supported data formats • HP-GL formats: HP-GL, HP-GL2, and HP-RTL • Versatec formats: Versatec Random Format (VRF), Versatec Color Graphic Language (VCGL) • TIFF formats: Conforming to TIFF version 6.0 • CALS formats: CALS type 1 •...
Page 295 Versatec Parallel Interface 8-bit parallel Maximum transfer speed:1 Mbps Maximum cable length:300 m Ethernet connection Server function: Data transfer by lpr and FTP Maximum number of sessions:10 each for lpr and FTP 9.1 Main Specifications (6030/6050) Downloaded From ManualsPrinter.com Manuals...
Page 296 Standard sizes and drawing areas Standard Series Dimensions Drawing area (dots) size × × 1,189 mm 19,872 28,064 (33.12 x 46.77") × × 841 mm 14,016 19,872 (23.36 x 33.12") × × ISO A 594 mm 9,920 14,016 series (16.53 x 23.36") ×...
Page 297 18 x 24 inches 10,800 x 14,400 (457 x 609 mm) 12 x 18 inches 7,200 x 10,800 (304 x 457 mm) 9 x 12 inches 5,400 x 7,200 (228 x 304 mm) 9.1 Main Specifications (6030/6050) Downloaded From ManualsPrinter.com Manuals...
Page 298 Print Length • When the PS/PDF option is not in use 1024MB Paper Type Paper Width 512MB (Standard) (Extended) 5,500mm 15,000mm Plain paper 7,500mm 15,000mm 6,000mm 6,000mm 6,000mm 6,000mm 36" 5,000mm 13,500mm 24" 6,900mm 15,000mm 18" 6,000mm 6,000mm 12" 6,000mm 6,000mm Vellum/Film 2,380mm...
Page 299 Frame memory - Maximum number of spools indicates the number of spools that are developed into bit map. The print entry data is spooled in the hard disk separately from the memories. 9.1 Main Specifications (6030/6050) Downloaded From ManualsPrinter.com Manuals...
Page 300: Main Specifications (6050A)
CalComp 906/907/951/PCI • FileNET • NIRS • • VCGL • • Versatec Data Standards • Xerox Emulation 150 • • JPEG • ® ® ™ Optional (Adobe PostScript , PDF (1.6), DWF, BMP, JPEG 2000, PNG, GIF, DGN) Chapter 9 Specifications...
Page 301 Host system interfaces TCP/IP Physical interface: 10-100Base-T (using manual selection) 10-100-1000Base-T (using auto selection with use of Cat6 cable) Maximum transfer speed:10/100/1000 Mbps Data link: Cat6 cable required for gigabit data transfer Ethernet connection Server function: Data transfer by lpr and FTP Maximum number of sessions:10 each for lpr and FTP 9.2 Main Specifications (6050A) Downloaded From ManualsPrinter.com Manuals...
Page 302 Standard sizes and drawing areas Standard Series Dimensions Drawing area (dots) size × × 1,189 mm 19,872 28,064 (33.12 x 46.77") × × 841 mm 14,016 19,872 (23.36 x 33.12") × × ISO A 594 mm 9,920 14,016 series (16.53 x 23.36") ×...
Page 303 Standard Series Dimensions Drawing area (dots) size × 44 inches 20,400 x 26,400 (863.6 x 1117.6 mm) × 34 inches 13,200 x 20,400 (558.8 x 863.6 mm) ANSI × 22 inches 10,200 x 13,200 (431.8 x 558.8 mm) × 17 inches 6,600 x 10,200 (279.4 x 421.8 mm) ×...
Page 304 Print Length Paper Type Paper Width 512MB (Standard) Plain paper/ 3,600mm Vellum/Film 7,272mm 14,544mm 29,088mm 58,176mm Maximum print length = 50,000mm. Chapter 9 Specifications Downloaded From ManualsPrinter.com Manuals...
Page 305: Media Specifications
Media Specifications • For sharp image copying, use the media recommended by Xerox. • To prevent media jams or uneven printing, do not use creased, wrinkled, or curled media. • When using unusually flexible media, support the media as it comes out of the media ejection port so that it will not be pressed against the media table and result in jams.
Page 306: Machine Specifications (6030/6050)
99 sheets maximum Copy speed A0 size: 5 sheets/min or higher (6050 Wide Format) A0 size: 3 sheets/min or higher (6030 Wide Format) Scan length Maximum: 15 m/49.2’ (at 100% scaling) Media feeding Auto paper feed from roll Manual media feed (option)
Page 307 No power is consumed in the output section and printer when the circuit breaker is OFF even if the power plug is connected to the power source. * Maximum length will differ based on the amount of memory installed. 9.4 Machine Specifications (6030/6050) Downloaded From ManualsPrinter.com Manuals...
Page 308 Xerox 6030/6050 Wide Format Amount of A0 size A1 size A2 size A3 size memory installed 512 Mbyte 7.5 m 7.5 m 1024 Mbyte 15 m 15 m Chapter 9 Specifications Downloaded From ManualsPrinter.com Manuals...
Page 309: Machine Specifications (6050A)
999 sheets maximum Copy speed A0 size: 5 sheets/min or higher (6050 Wide Format) A0 size: 3 sheets/min or higher (6030 Wide Format) Scan length Maximum: 15 m/650’ (at 100% scaling) Media feeding Auto paper feed from roll Manual media feed (option) method 9.5 Machine Specifications (6050A)
Page 310 Item Specification Media Maximum width: 914 mm/36" (A0 size) Minimum width: 210 mm/8.27" (A4 size) Maximum length *:Plain media (A0/A1 width) 15 m/ 650’, A2/A3 width 6 m/19.68’ Vellum/Film: Twice standard size Minimum length: 210 mm/8.27" 1,250 (W) × 640 (D) × 1,200 (H) Dimensions Combination type mm (excluding control panel)
Page 311 Appendixes Downloaded From ManualsPrinter.com Manuals...
Page 312 Appendix 1 Connector Specifications RS-232C pin assignment (6030/6050 only) PIN No. Controller side Signal name Wiring Host side Straight cable Cross cable [-] indicates no wiring. Both sides are male pins. Centronics pin assignment Printer Side (36-pin Amphenol half-pitch type)
Page 313 Host Side (36-pin Amphenol type) Terminal Terminal Signal name Signal name Pin connection nStrobe Data 1 Data 2 Data 3 Data 4 Data 5 Data 6 Data 7 Data 8 nAck Busy Perror Select nlnit nAutoFd nFault Logiv GND Chassis GND Peripheral nSelectln Logic High...
Page 314: Command List
Appendix 2 HP-GL/HP-GL2 Command List (6030/6050) This section explains the HP-GL and HP-GL/2 command support status that are unique to the 6030/6050 Wide Format. Command fully supported. Activates different actims from other ordinary commands. (Meaning in [ ]) Command not supported and ignored.
Page 315 X and Y coordinates. Cuts paper. Draws a polygon registered in the polygon buffer. Draws a square determined by the current pen position and relative coordinates from the point. Appendix 2 HP-GL/HP-GL2 Command List (6030/6050) Downloaded From ManualsPrinter.com Manuals...
Page 316 6030/6050 Com- Command Meaning and action HP-GL HP-GL/2 mand Wide Format Specifies the character spacing. Draws a sector. Specifies a font as the primary font. Specifies a font as the secondary font. Fills in a polygon registered in the polygon buffer.
Page 317 Outputs the current position instructed by the last command and the pen up-down information. [6030/6050 Wide Format: Always returns the standard value (0,0,0)] Outputs read coordinates. [Always returns the y* (HP-GL) standard value (0,0,0)] n (HP-GL/2) Outputs an error number.
Page 318 6030/6050 Com- Command Meaning and action HP-GL HP-GL/2 mand Wide Format Feeds the paper forward or backward. y* (HP-GL) y (HP-GL/2) Registers a user-specified polygon in the polygon buffer. Moves the pen by relative coordinates. Specifies the paper size. y (HP-GL) y* (HP-GL/2) Specifies the fill spacing.
Page 319 Defines and fills in a sector polygon. Specifies whether to express the pen width in millimeters or by percentage of the P1/P2 distance. Draws ticks on the X axis. Draws ticks on the Y axis. Appendix 2 HP-GL/HP-GL2 Command List (6030/6050) Downloaded From ManualsPrinter.com Manuals...
Page 320 Appendix 3 HP-RTL Command List (6030/ 6050) Command name Command Command Meaning and function Limit Enter HPGL/2 Mode ESC % # B Starts processing the following data Transfer color palette ignored as an HP-GL2 command. Enter PCL Mode ESC % # A...
Page 321 ESC * p # y|Y Moves the CAP vertically by a specified value in Versatec resolution inch units. Y Offset ESC * b # y|Y Moves the CAP vertically by specified pixel rows. Appendix 3 HP-RTL Command List (6030/6050) Downloaded From ManualsPrinter.com Manuals...
Page 322 Command name Command Command Meaning and function Limit Destination Raster ESC * t # h|H Defines the raster output width for Width succeeding Start Graphic command by decipoint (1/720 inch). Destination Raster ESC * t # v|V Defines the raster output height for Height succeeding Start Graphic command by decipoint (1/720 inch).
Page 323 Appendix 4 TIFF Tag List (6030/6050) Tag ID Revision 6030/6050 Tag Name Wide Format 00FE NewSubfileType Bit 0: Low Resolution Image Bit 1: Multi-Page Image Bit 2: Transparency Mask 00FF SubfileType 1: Full Resolution Image 2: Reduced-Resolution Image 3: Multi-Page Image...
Page 324 Tag ID Revision 6030/6050 Tag Name Wide Format 8: CIELab 0107 Thresholding 1: No Dithering or Halftoning 2: Dithering or Halftoning 3: Randomized-Processed Image 0108 CellWidth 0109 CellWidth 010A FillOrder 1: MGB 2: LSB 010D DocumentName 010E ImageDescriprion 010F Make...
Page 325 1: No absolute unit 2: Inch 3: Centimeter 0129 PageNumber 012D TransferFunction 0131 SoftWare 0132 DateTime 013C HostComputer 013E Predictor 013D WhitePoint 013F PrimaryChromaticties 0140 ColorMap 0141 HalftoneHints 0142 TileWidth 0143 TileLength Appendix 4 TIFF Tag List (6030/6050) Downloaded From ManualsPrinter.com Manuals...
Page 326 Tag ID Revision 6030/6050 Tag Name Wide Format 0144 TileOffsets 0145 TileByteCounts 014C InkSet 014D InkNames 014E NumberOfInks 0150 DotRange 0151 TargetPrinter 0152 ExtraSamples 0153 SampleFormat 1: unsigned integer data 2: 2's complement signed integer data 3: IEEE formatting point...
Page 327 Tag ID Revision 6030/6050 Tag Name Wide Format 8298 33432 Copyright Appendix 4 TIFF Tag List (6030/6050) Downloaded From ManualsPrinter.com Manuals...
Page 328 Appendixes Downloaded From ManualsPrinter.com Manuals...
Page 329 Symbols "1.1 Outline of Xerox 6030/6050 Wide Format Print Service" 41, 146 90-degree rotation administrator top page Alignment mark printing area mode AUTO (Input Option) AUTO (output option) auto layouts auto mapping Auto R/E auto roll auto scale auto-layout automatic mapping...
Page 330 EOP command Error Log error log 136, 137 error message film 224, 231 FTP command help image fragmentation function input image size input media series Input Option 33, 267, 273 interface IOT status IP command IPQ command 224, 240 IPR command IPRM command 47, 176, 208 job log...
Page 331 media size media tray (optional) media tray (standard) 121, 166 media type (Menu) button 188, 213, 214 meter display method of cutting paper 41, 146 mirror image MIX (output option) MIX2 (output option) MSI & manual paper feed unit offline mode 47, 212 offline plot 41, 127...
Page 332 42, 212 reprinting resolution 139, 168 roll media RS232C serial (Set) button 148, 151, 156 sets joint processing for lines 148, 151, 156, 160, 161 sets the end of the line setup screen shaft 40, 117, 169 size mapping size recognition priority mode 123, 139 size specification sleep mode...

This manual is also suitable for:

6050a 6050

Xerox 6030 User Manual

Chapter 2 Printer Overview

Chapter 3 Printer Setup

Chapter 4 Logical Printer Setup and Operation (6030/6050 Only)

Chapter 5 Additional Operations from the Printer Menu

Chapter 6 Ethernet Print Service (for UNIX)

Chapter 7 Maintenance

Chapter 8 Problem Solving

Chapter 9 Specifications

Quick Links

Related Manuals for Xerox 6030

Summary of Contents for Xerox 6030