Download  Print this page

Xerox 6030 User Manual

Wide format printer
Hide thumbs

Advertisement

Xerox 6030/6050/6050A
Wide Format Printer User Guide
701P47273
Version 2.0
August 2007

Advertisement

Table of Contents
loading

  Also See for Xerox 6030

  Related Manuals for Xerox 6030

  Summary of Contents for Xerox 6030

  • Page 1 Xerox 6030/6050/6050A Wide Format Printer User Guide 701P47273 Version 2.0 August 2007...
  • Page 2 Global Knowledge & Language Services 800 Phillips Road Bldg. 845-17S Webster, NY 14580 Copyright © 2007 Xerox Corporation. All rights reserved. Printed in the United States of America. Copyright protection claimed includes all forms and matters of copyrighted material and information now allowed by statutory or...
  • Page 3 Format, has been revised to accomodate the Xerox 6050A Wide Format. The reader should assume that any topic, section, heading, sentence, or bullet not denoted as being related to either the 6030/6050 or 6050A Wide Format is applicable to both products.
  • Page 4 Conventions This User Guide uses the following symbols and conventions: < > key " " Preface Indicates the keys on the keyboard. Press the <Enter> key. Indicates the menus and display items on the screens. Select either the [On] or [Off] buttons to display [Job Name], [Owner], and [Reason] in that order.
  • Page 5: Safety Notes

    Read these safety notes carefully before using this product to ensure you operate the equip- ment safely. Your Xerox product and recommended supplies have been designed and tested to meet strict safety requirements. These include safety agency approval, and compliance with established environmental standards.
  • Page 6 1989 Regulation. Customers wishing to complete safety testing should contact Xerox for advice prior to any test implementation. Xerox equipment should, however, be properly and regularly serviced and maintained at all times.
  • Page 7 MISLEADING RESULTS AND MAY CAUSE DEATH, PERSONAL INJURY AND/OR DAMAGE TO PROPERTY. QUESTION: I would like to carry out my own safety tests on the Xerox equipment in my pre- mises. ANSWER: You may, of course, request such tests as you deem necessary to satisfy yourself that your Xerox equipment is safe.
  • Page 8: Electrical Supply

    PLEASE NOTE: YOU MUST ENSURE THAT YOUR XEROX EQUIPMENT IS SAFE AT ALL TIMES This product shall be operated from the type of electrical supply indicted on the product 's data plate label. If you are not sure that your electrical supply meets the requirements, please consult your local power company for advice.
  • Page 9: Emergency Power Off

    • This equipment is to be used on a dedicated 20A, 208-240 Vac 60Hz circuit or 16A, 220-240 Vac 50Hz circuit. The equipment must be connected to a grounded main outlet. If this machine needs to be moved to a different location, contact a Xerox service representative or your authorized local representative or service support organization.
  • Page 10: Disconnect Device

    • Always follow all warnings and instructions that are marked on or supplied with the equipment. • Always exercise care when moving or relocating equipment. Please contact your local Xerox/ Fuji Xerox Service Department, or your local support organization to arrange relocation of the product to a location outside of your building.
  • Page 11: Maintenance Information

    Contact your Xerox sales representative (1-800-ASK-XEROX) to determine whether this Xerox product is part of the program. For more information about Xerox environmental programs, visit http://www.xerox.com/environment. If you are managing the disposal of your Xerox product, please note that the prod- Safety Notes...
  • Page 12: For Consumables

    Changes and modifications to this equipment not specifically approved by Xerox/ Fuji Xerox may void the user's authority to operate this equipment. Shielded interface cables must be used with this equipment to maintain compli- ance with FCC regulations in the United States and the Radio Communications Act 1992 in Australia/New Zealand as applicable.
  • Page 13: Product Safety Certification

    This Class "A" digital apparatus complies with Canadian ICES-003. Cet appareil numérique de la classe "A" est conforme à la norme NMB-003 du Canada. Product Safety Certification This product is certified by the following Agencies using the Safety standards listed. AgencyStandard TUV Rheinland of North America, Inc.
  • Page 14: Regulatory Information

    Regulatory Information CE Mark The CE mark applied to this product symbolizes Xerox's declaration of conformity with the following applicable Directives of the European Union as of the dates indi- cated: January 1, 1995: Council Directive 72/23/EEC amended by Council directive 93/ 68/EEC, approximation of the laws of the member states related to low voltage equipment.
  • Page 15: Environmental Compliance

    Xerox ENERGY STAR equipment is preset at the factory to enter a ”low power” state and/or shut off completely after a specified period of use. These energy-sav- ing features can reduce product energy consumption in half when compared to conventional equipment.
  • Page 16 Terra Choice Environmental Services, Inc. of Canada has verified that this product conforms to all applicable Environmental Choice EcoLogo requirements for mini- mized impact to the environment. As a participant in the Environmental Choice program, Xerox Corporation has determined that this product meets the Environmental Choice guidelines for energy efficiency.
  • Page 17: Product Recycling And Disposal

    Xerox product is part of the program. For more information about Xerox environmental programs, visit www.xerox.com/environment. If you are managing the disposal of your Xerox product, please note that the prod- uct contains lead, mercury and other materials whose disposal may be regulated due to environmental considerations.
  • Page 18: Illegal Copies And Printouts

    Illegal Copies and Printouts Congress, by statute, has forbidden the reproduction of the following subjects under certain circumstances. Penalties of fine or imprisonment may be imposed on those guilty of making such reproductions. 1. Obligations or Securities of the United States Government, such as: Certificates of Indebtedness Coupons from Bonds Silver Certificates...
  • Page 19 1. Stamps and other representatives of value, of whatever denomination, which have been or may be issued under any Act of Congress. 2. Adjusted Compensation Certificates for Veterans of the World Wars. 3. Obligations or Securities of any Foreign Government, Bank, or Corporation. 4.
  • Page 20 Canada Parliament, by statute, has forbidden the reproduction of the following subjects under certain circumstances. Penalties of fine or imprisonment may be imposed on those guilty of making such reproductions. 1. Current bank notes or current paper money. 2. Obligations or securities of a government or bank. 3.
  • Page 21: Other Countries

    This list is not inclusive and no liability is assumed for either its completeness or accuracy. In case of doubt, contact your legal counsel. Safety Extra Low Voltage Approval These Xerox Digital Copiers/Printers are in compli- ance with various governmental agencies and national safety regulations. All system ports meet...
  • Page 22 xviii Illegal Copies and Printouts...
  • Page 23: Table Of Contents

    1.11 Cutting Roll Media ... 24 Cutting Roll Media Manually... 25 Chapter 2 Printer Overview Overview of the 6030/6050/6050A Wide Format Printer ... 32 What is the 6030/6050/6050A Wide Format Printer?... 32 Print Service Operations ... 36 Main Printing Functions... 38 Printer Control Panel Usage...
  • Page 24 3.12 Software Option (Print Services on Web, 6030/6050)... 101 3.13 Software Option (Web Printer Management Tool, 6050A) ... 102 3.14 Change Password (Print Services on Web, 6030/6050) ... 103 3.15 Change Password (Web Printer Management Tool, 6050A) ... 104 3.16 Change Default Language (Print Services on Web, 6030/6050)... 105 3.17 Change Default Language (Web Printer Management Tool, 6050A) ...
  • Page 25 Split Drawing ... 134 Message Option ... 136 Printed Copy... 138 Output Option ... 139 Size Recognition ... 142 Color Option ... 144 Transform ... 145 Define Single Pen... 147 Define Multi Pen ... 151 Pen Option... 152 Emulation ... 153 PS Command ...
  • Page 26 Printer Control Panel Menu (6030/6050)... 197 Printer Control Panel Menu (6050A) ... 203 Test Printing (6030/6050 only)... 207 Managing the Job and Error Logs (6030/6050 only) ... 208 Job Log... 208 Error Log (6030/6050 only) ... 210 Reprinting (6030/6050 only) ... 212 Billing Meter Confirmation (6030/6050)...
  • Page 27 Message List (6030/6050 only) ... 249 Chapter 7 Maintenance Loading Toner... 252 Chapter 8 Problem Solving Check the Control Panel(s) ... 256 Poor Image Quality ... 257 Other Problems ... 258 Printer Troubleshooting... 259 Jams in the Feeder (Roll Media) ... 261 Jams in the Printer and Ejection Port ...
  • Page 29: Product Overview

    Chapter Chapter 0 Product Overview...
  • Page 30: Product Configurations

    Product Configurations The following product configurations and options are available for the Xerox 6030/6050/6050A Wide Format Printer and the Xerox 6030/6050/6050A Wide Format Copier/Printer. Xerox 6030/6050/6050A Wide Format Printer This unit is a printer only. Refer to the printer sections of this guide for information about its setup, features, and usage.
  • Page 31 Xerox 6030/6050/6050A Wide Format Printer with Scan System This unit features copier and printer functionality, plus the Wide Format Scan System and the FreeFlow Accxes Xerox 6030/6050 Wide Format Printer with Scan System (HFT controller shown is not available with the 6050A) Xerox 6030/6050/6050A Wide Format Options You may acquire additional hardware and software options for all units.
  • Page 32: Major Components

    Major Components Major Components: Front ( *6030/6050 Copier/Printer only ) Document table Setup screen (touch screen) Control panel Document insertion guide Printer control panel MSI*/Manual Feed Unit (*Multi Sheet Inserter) (optional) Feeder LED Media tray (6050 only) Media tray (Standard) Name Documents to be scanned are inserted here.
  • Page 33 *10 Scanner power switch Toner supply port Major Components: Rear ( *6030/6050 Copier/Printer only ) *1 Document ejection port *2 Power outlet socket Print ejection port 1.2 Major Components Name Switches the power to the scanner on and off. Name The toner is refilled through this port.
  • Page 34 *4 Remote switch *5 Interface connector *6 Serial port connector Circuit Breaker Switch Paper Heater Switch Main Power Switch Connections to the host computer and other necessary connections will be taken care of by your service representative. Name A selector switch that enables the user to switch the power to both the scanner and the printer on and off from the Main Power Switch.
  • Page 35: Power On/Off

    Breaker Switch must be in the ON position to switch the printer and scanner power on and off. No power is consumed when the Circuit Breaker Switch is in the OFF position, even though the power plug is connected to the power source. Powering On 6030/6050 Scanner Power Switch...
  • Page 36 Powering Off 6030/6050 Switch off the power following the steps below. Never switch off the power while the machine is printing. Failure to observe this precaution may result in paper jams in the high-temperature areas of the printer. Main Power...
  • Page 37 Powering Off 6050A Switch off the power following the steps below. Never attempt to switch off the power while the machine is printing. Failure to observe this precaution may result in paper jams in the high-temperature areas of the printer. 1.3 Power On/Off Press the <Menu>...
  • Page 38: Power Save Mode

    This mode reduces the temperature of the fuser more than Low power mode 1. The parameters that can be set up are only [ON] and [OFF] on the 6030/ 6050, and the time that must elapse before the mode activates is 5 to 120 minutes;...
  • Page 39 Refer to "3.8 System Parameter Setup (Print Services on Web, 6030/6050)" for changing the power save mode settings from the printer control panel. 1.4 Power Save Mode...
  • Page 40: Printer Control Panel Overview

    Refer to section "2.2 Printer Control Panel Usage" and Chapter 5 for detailed explanations of the use of the printer control panel. It is seldom necessary to use the printer control panel on the 6030/6050 Wide Format Copier/Printer because the same settings usually can be made using either the copier control panel or Print Services on Web, the built-in web interface.
  • Page 41: Print Services On Web Overview (6030/6050)

    Print Services on Web Overview (6030/ 6050) Print Services on Web is web server software which is pre-installed in the 6030/ 6050 Wide Format Printer and Copier/Printer. Print Services on Web provides a user-friendly way to perform printer setup, communication (port) setup, job and error log management, and other procedures via a web browser.
  • Page 42: Operating Modes

    [Job and Log] tab [Status tab] [Print Setup] tab Refer to section "1.7 Logical Printers Overview (6030/6050)" to learn more about logical printers. Check the status of a print job. View and print a job log.
  • Page 43 [Print Setup] tab [Properties] tab [Tools] tab 1.6 Print Services on Web Overview (6030/6050) • Check the status of jobs in the print queue. • View and print the job log and the error log. • Cancel a print job.
  • Page 44: Logical Printers Overview (6030/6050)

    Stored Jobs are to copying, that is, both reduce setup time and increase efficiency by using previously saved job settings. A maximum of one hundred logical printers can be set up within one 6030/6050 Wide Format Printer or Copier/Printer for each supported data format.
  • Page 45: Loading Roll Media

    Loading Roll Media The message ‘Replace xxx media." will display when there is no media loaded or when the roll in use runs out. The media size displayed on the control panel will turn off when there is no media in the machine. Two rolls of media can be loaded in each of the media trays.
  • Page 46 While pulling on the lever located in the end of the roll paper shaft, remove the paper core in the direction of the arrow. Pulling the lever releases the lock and allows the roll to be removed from the shaft. There is an area at the front of the tray on which the roll paper can be placed.
  • Page 47 Set up the media parameters on the copier control panel. For the 6050A and 6030/6050 Printers without copiers, the media parameters also may be set up on the printer control panel. "Chapter 5 Additional Operations from the Printer Menu"...
  • Page 48: Drawer Media Size Indicators

    Drawer Media Size Indicators The media size indictors help the user identify the media that is loaded in each of the drawers. These indicators are visible on the right hand side of the drawers. Usage instructions begin on the next page. The following types are available.
  • Page 49: Inserting Media Size Sheets

    Inserting media size sheets 1.9 Drawer Media Size Indicators Open the tray. Remove the media size sheet. Fold the sheet so that the size loaded is displayed. Insert the media size sheet.
  • Page 50 Gently but firmly close the media tray.
  • Page 51: Loading Media For Manual Feeding

    1.10 Loading Media for Manual Feeding Make the required media settings on the copier control panel. 1.10 Loading Media for Manual Feeding Adjust the (MSI) Multi Sheet Inserter/ Manual Feed Unit's side guides to fit the size of the media that is to be printed. Set the correct media series for the manual feed sheet.
  • Page 52: Cutting Roll Media

    There are two methods for cutting the lead edge of the roll media: • Automatic cut: Refer to the section "5.7 Billing Meter Confirmation (6030/6050)" for the 6030/6050 and "5.8 Billing Meter Confirmation (6050A)" for the 6050A in "Chapter 5 Additional Operations from the Printer Menu" for details about automatic cutting.
  • Page 53: Cutting Roll Media Manually

    Cutting Roll Media Manually Cutting the Front Roll Lever 1.11 Cutting Roll Media Open the media tray. Pull the lever to open the tray cover. Rotate the roll media until the lead edge is gripped by the roller.
  • Page 54 Window Rotate the knob until the media's lead edge protrudes from the tray outlet. Grasp the cutter by the handle and slide it to the opposite side of the tray to cut the paper. CAUTION: Use the cutter handle to prevent personal injury which may result from sliding your fingers along the sharp, metal cutting bar.
  • Page 55 Cutting the Rear Roll 1.11 Cutting Roll Media Close the media tray. Open the media tray. Rotate the roll paper until the lead edge is gripped by the roller.
  • Page 56 Rotate the knob until the media's lead edge protrudes from the tray outlet. Pull the lever to open the tray cover. Rotate the knob until the paper passes through the tray outlet. Grasping the cutter by the handle, slide the cutter to the opposite side of the tray to cut the paper.
  • Page 57 Return the media to its original location by rotating the knob until the lead edge can be seen in the window. Close the media tray. 1.11 Cutting Roll Media...
  • Page 59: Chapter 2 Printer Overview

    Chapter Chapter 0 Printer Overview Chapter 2...
  • Page 60: Overview Of The 6030/6050/6050A Wide Format Printer

    What is the 6030/6050/6050A Wide Format Printer? The 6030/6050/6050 Wide Format printer processes print jobs that it receives from a client. The 6030/6050/6050A Wide Format printer enables all types of image data to be printed in the supported formats, including standard and non- standard size documents, enlarged and reduced images, and split (fragmented) images.
  • Page 61 • VPI (optional) Communication Interfaces (6050A) The following communication interfaces are supported. • TCP/IP 10/100/1000 • • TFTP 2.1 Overview of the 6030/6050/6050A Wide Format Printer ® ® ™ PostScript , PDF (1.6), DWF, BMP, JPEG 2000, PNG, GIF, DGN)
  • Page 62 Printing Methods (6030/6050) Documents may be submitted from a client to the 6030/6050 Wide Format Printer using any of the following. • Ethernet (Direct) Printing This capability is for UNIX systems. Printing takes place over TCP/IP networks using the ftp and lpr commands.
  • Page 63 Accxes Client Tools is printer support software that runs on Windows Solaris operating systems. Using the Accxes Client Tools simple user interface, the user can submit documents to the 6050A Wide Format printer. Refer to the Xerox 6050A Accxes Client Tools User Guide for details on available functions. •...
  • Page 64: Print Service Operations

    • job log and error log management • reprinting of the most recent print job (6030/6050 only) • displaying billing meter information Refer to "2.2 Printer Control Panel Usage" for more details on the printer control panel and its usage.
  • Page 65 Print Services on Web (6030/6050 only) Print Services on Web is web server software which is pre-installed in the 6030/ 6050 Wide Format. Print Services on Web provides a user-friendly way to perform printer setup, communication (port) setup, log management, and other procedures via a web browser.
  • Page 66: Main Printing Functions

    Stored Jobs are to copying, that is, both reduce setup time and increase efficiency by using previously saved settings. A maximum of one hundred logical printers can be set up within one 6030/6050 Wide Format Printer or Copier/ Printer for each supported data format.
  • Page 67 • Refer to "3.8 System Parameter Setup (Print Services on Web, 6030/6050)" for details on setting up the logical printer extensions. • Refer to "4.1 Creating a New Logical Printer" for help in setting up logical printers. Document Size Input...
  • Page 68 Size Mapping Size mapping is the process of setting up a table that establishes relationships between input document sizes and output image sizes. When size mapping is finished (must be done prior to printing), documents can be enlarged or reduced automatically based on the table entries.
  • Page 69 These functions perform mirroring (Mirror Image) or 90-degree rotation processing on the output image. Refer to the "Transform" section of "4.3 Logical Printer Print Settings" for details on available functions. Input document 2.1 Overview of the 6030/6050/6050A Wide Format Printer Plot area Output images Output images Auto-layout...
  • Page 70 The most recently printed document can be reprinted. The print quantity also can be specified. Reprinting is not possible with the Xerox 6030 WF or Xerox 6050 WF if a copy job is performed after the print operation. Refer to "5.6 Reprinting (6030/6050 only)" for details on available functions.
  • Page 71: Canceling Jobs

    "4.5 Print Services on Web: Job and Log" for details on Print Service on Web operations. Meter Display The billing meters can be checked from both Print Services on Web (6030/6050 only) and the printer control panel. Refer to "4.6 Print Services on Web: Status" for details on web operations, and "5.7 Billing Meter Confirmation (6030/6050)"...
  • Page 72: Printer Control Panel Usage

    Printer Control Panel Usage This section describes the names and functions of the printer control panel components. [Processing] lamp (green) Indicates the printing status. Printing in process Blinking Receiving print data Not printing Printer display Used for setting up the various functions.
  • Page 73: Basic Printer Control Panel Operations

    Basic Printer Control Panel Operations The printer must be in the offline mode before settings can be changed. Pressing the <Menu> key switches the printer to the offline mode and displays the menu screen. Button Functions The following buttons are used to navigate the menu screen. <Menu>...
  • Page 74: Overview Of The Operation Menu

    Sets up the system management information, such as the system date and power save mode settings. Refer to "3.2 Communication Parameter Setup (Printer Control Panel, 6030/ 6050)" for the 6030/6050 and "3.3 Communication Parameter Setup (Printer Control Panel, 6050A)" for the 6050A for setup procedures.
  • Page 75 Refer to "5.4 Test Printing (6030/6050 only)" for logical printer details and operations. JOB LOGGING MENU Prints job and error logs. Refer to "5.5 Managing the Job and Error Logs (6030/6050 only)" for logical printer details and operations. OFFLINE PLOT MENU Reprints the most recently printed job.
  • Page 76 Operation Examples This section provides examples of how to select menu items. <Menu> key Ready to print MENU NETWORK/PORT SET < > key MENU SYSTEM PARAMETER < > key MENU PORT SETTING < > key PORT SETTING TCP/IP < >< >...
  • Page 77 Setting Up a Value This section provides an example of setting up a value. SYSTEM PARAMETER Smoothing < > key Smoothing < >< > key Smoothing <Set> key Smoothing < > key SYSTEM PARAMETER Smoothing 2.2 Printer Control Panel Usage Select the menu item that you want to set up so that it displays on the screen.
  • Page 78 Entering Numbers and Characters This section provides examples of how to enter numbers and characters. SYSTEM PARAMETER Low power mode1 < > key Timer Value < >< > key Timer Value < > key Timer Value < >< > key Timer Value <Set>...
  • Page 79: Print Services On Web (6030/6050)

    Print Services on Web (6030/6050) Print Services on Web is web server software which is pre-installed in the 6030/ 6050 Wide Format. Print Services on Web enables the user to perform the following procedures from a workstation using a web browser.
  • Page 80: Starting And Exiting Print Services On Web

    This section explains how to start and exit Print Services on Web. Start Print Services on Web Start the browser. Enter the URL for the 6030/6050 Wide Format (http://Home name or IP address) in the browser's address field, and then press the <Enter> key.
  • Page 81: Print Services On Web Organization

    The administrator page (see next page) displays after the user selects the [Administrator page] button on the user page, and then enters the user name and password in the logon dialog box. 2.3 Print Services on Web (6030/6050) Check the status of a print job. View and print a job log.
  • Page 82 The administrator page permits the following. [Job and Log] tab [Status tab] [Print Setup] tab [Properties] tab [Tools] tab • Check the status of jobs in the print queue. • View and print the job log and the error log. •...
  • Page 83 Click the Help [?] button displayed at the top, right corner of the window to display the online help. The online help enables you to answer many questions related to using Print Services on Web. 2.3 Print Services on Web (6030/6050)
  • Page 84: Freeflow Accxes Web Print Management Tool (6050A)

    • Network bandwidth and speed • Amount of data being transmitted to or from the printer’s Controller • Network traffic The Web Printer Management Tool provides the following services to users of Xerox Wide Format Printers. Chapter 2 Printer Overview...
  • Page 85: Users

    Users • View printer status (including media inventory) and the print queue • View the printer defaults • View the Job Accounting mode for remote print jobs • Generate test prints showing configuration data (such as the Controller’s TCP/ IP address) System Administrators with the Password •...
  • Page 86: Using Web Print Management Tool Main Menu

    Using Web Print Management Tool Main Menu The Main Menu contains six selections in hypertext form allowing you to jump to other web pages. P r i n t e r Configuration Queue Printer Queue This selection contains 3 tabs for viewing the Job Queue, Mismatched Job Queue and the Active Job Queue.
  • Page 87: Chapter 3 Printer Setup

    Chapter Chapter 0 Printer Setup Chapter 3...
  • Page 88: Communication Parameters

    Copier/Printer is connected to the network, the communication parameters must be set up. The communication parameters can be set up from the printer control panel or from Print Services on Web (6030/6050). This section explains how to use both methods to perform the setup procedures. Explained, too, is the procedure for printing a list of the communication parameters.
  • Page 89 TCP/IP The communication parameter nomenclature on the printer control panel will sometimes differ from the nomenclature on Print Services on Web (6030/ 6050) or Web Printer Management Tool (6050A). The Print Service on Web and Web Printer Management Tool nomenclature appears in bold type in the table below.
  • Page 90 \*The ROUTING TABLE can be edited if [Static Routing] is set to [Enable]. A maximum of 512 items can be saved in the routing table. The [Registration Not Possible] screen will display if the number of items exceeds 512. Menu Item ROUTING TABLE Dest.
  • Page 91 The following TCP/IP communication parameters can be set up for the 6050A using using the printer control panel on the device itself or using the Web Printer Management Tool. Menu Item Ethernet Setting IP Address MASK Value Gateway *E-Net Address DHCP RARP/BOOTP (UNIX) 3.1 Communication Parameters...
  • Page 92 Serial (6030/6050 Only) The serial communication parameters are listed below. The communication parameter nomenclature on the printer control panel will sometimes differ from the nomenclature on Print Services on Web. The Print Service on Web nomenclature appears in bold type in the table below.
  • Page 93 Menu Item Job Separation (Page limit) 3.1 Communication Parameters Description Sets up the job separation option. The default setting is [NO]. [YES] Starts data conversion once the command that recognizes the end of the data is received, even if it occurs midway through the file.
  • Page 94 Centronics (optional, 6030/6050 Only) The Centronics communication parameters are presented below. Menu Item Ack Mode DMA Timeout EOP Timeout Job Separation • If a value higher than [255] is entered for the DMA Timeout value, [255] will be set as the value.
  • Page 95 VPI (optional, 6030/6050 Only) The following VPI communication parameters must be set up. Menu Item REPORT OFFLINE EOP Timeout Job Separation *If a value higher than [255] is entered for the timeout value, [255] will be set as the value.
  • Page 96 SNMP (6030/6050 Only) The communication parameters listed below must be set up. SNMP must be set up in Print Services on Web. The communication parameter nomenclature on the printer control panel will sometimes differ from the nomenclature on Print Services on Web. The Print Service on Web nomenclature appears in bold type in the table below.
  • Page 97: Communication Parameter Setup (Printer Control Panel, 6030/6050)

    Ethernet Setting Ethernet Setting AUTO TCP/IP Setup 3.2 Communication Parameter Setup (Printer Control Panel, 6030/6050) Press the < displayed. Select the interface that is to be set up with the use of the < > and < > keys, and then press the <...
  • Page 98 PORT SETTING TCP/IP TCP/IP Default Parser Default Parser HPGL IP Address 100. 000. 000. 000 IP Address 120. 000. 000. 000 IP Address 123. 123. 123. 001 Display [TCP/IP] on the selection screen, and then press the < Select the item that is to be set up with the use of the <...
  • Page 99: Serial Setup

    Serial Setup PORT SETTING SERIAL SERIAL Baud Rate 3.2 Communication Parameter Setup (Printer Control Panel, 6030/6050) Adding items to the routing table 1. Select [ON] for [Static Routing], and then press the <Set> key. Now press the < 2. Select [ADD] for the [ROUTING TABLE], and then press the <...
  • Page 100 Baud Rate Centronics (optional) Setup PORT SETTING CENTRO CENTRO DMA Timeout DMA Timeout 005 sec VPI (optional) Setup PORT SETTING Job Separation Select the parameters with the use of the < > and < > keys, and then press the <Set>...
  • Page 101 Select the parameters with the use of the < > and < > keys, and then press the <Set> key. An asterisk [*] will display on the right side of the parameters once they have been set. 3.2 Communication Parameter Setup (Printer Control Panel, 6030/6050)
  • Page 102: Communication Parameter Setup (Printer Control Panel, 6050A)

    • Refer to the section TCP/IP Setup in "3.2 Communication Parameter Setup (Printer Control Panel, 6030/6050)" for information on how to set the [IP ADDRESS], [IP SUBNET MASK], and [IP GATEWAY] IP addresses..
  • Page 103: Communication Parameter Setup (Print Services On Web, 6030/6050)

    [Properties] tab. 3.4 Communication Parameter Setup (Print Services on Web, 6030/6050) Refer to "2.3 Print Services on Web (6030/6050)" for details about starting Print Services on Web and logging on as Administrator. The displayed [Print settings] were set up earlier using the selections on the [Print Setup] and the [Properties] tabs.
  • Page 104 Select the interface or protocol ([TCP/IP], [Serial], [Centro], [VPI], [SNMP]) to be set up from the [System parameters] menu. The setup selections will display in the right-hand pane of the window. In the example below, [Serial] has been selected. Set up each of the parameters as required, and then select the [Apply] button.
  • Page 105 To print a list of the settings, drag the right scroll bar to the bottom, and then select the [Print] button. After setting up all of the parameters, switch the Main Power Switch off and then on to enable the changes to take effect. 3.4 Communication Parameter Setup (Print Services on Web, 6030/6050)
  • Page 106: Communication Parameter Setup (Web Printer Management Tool, 6050A)

    Communication Parameter Setup (Web Printer Management Tool, 6050A) • Consult Web Printer Management Tool help system for details on communication parameter setup of the 6050A. Chapter 3 Printer Setup...
  • Page 107: System Parameter Setup (Printer Control Panel, 6030/6050)

    Control Panel, 6030/6050) The following system parameters can be set up from the printer control panel. These parameters can be set up on the copier control panel on the Xerox 6030/6050 Copier/Printers. If the parameters are set up on both the printer control panel and the copier control panel, the most recent settings will take precedence.
  • Page 108 Menu Item Sleep Mode Attention Light Buzzer Print Density Job Recovery Net Cont. Time 6030/6050 Printer Control Panel Example Procedure MENU SYSTEM PARAMETER SYSTEM PARAMETER Job Recovery Description Sets the sleep mode to [ON] or [OFF] and sets the time...
  • Page 109 Job Recovery 3.6 System Parameter Setup (Printer Control Panel, 6030/6050) [Sleep Mode], [Attention Light], [Print Density], [Job Recovery], and [Net Cont. Time] will display, in that order.. Press the < > key to select the item. Select the parameters using the < > and <...
  • Page 110: System Settings Setup (Printer Control Panel, 6050A)

    System Settings Setup (Printer Control Panel, 6050A) The following system parameters can be set up from the printer control panel. • Refer to "2.2 Printer Control Panel Usage" for detailed instructions on printer control panel operations. Menu Item TCP/IP Date/Time Timers Description Allows the entering of an IP Address, IP Subnet Mask...
  • Page 111 6050A Printer Control Panel Example Procedure MENU SYSTEM SETTINGS SYSTEM SETTINGS TCP/IP DHCP Enable* 3.7 System Settings Setup (Printer Control Panel, 6050A) Press the < > key with [MENU]/[SYSTEM SETTINGS] displayed. Scroll to the item you wish to set up using the <...
  • Page 112: System Parameter Setup (Print Services On Web, 6030/6050)

    The system parameters listed below can be set up from Print Services on Web. These procedures are performed on the Administrator page. Refer to "3.4 Communication Parameter Setup (Print Services on Web, 6030/6050)" for information about setting up the [TCP/IP], [Serial], [Centro], [VPI], and [SNMP] selections in the [System Parameters] menu on the Properties tab.
  • Page 113 Procedure Start Print Services on Web, log in as Administrator, and display the [Properties] tab. 3.8 System Parameter Setup (Print Services on Web, 6030/6050) Description Determines how the jobs that were in the print queue when the printer power was shut off will be processed when the printer is switched back on.
  • Page 114 Select the item that is to be set up from the [System parameter menu], for example, [Priority], [Replot], [Print density], [Paper Width for Special A], [Job Recovery], [Exclusive access time out], [Extension], and [Set date]. Setting Up [Priority] Select [Priority] from the [System parameters] menu. The [Priority] selections will display in the right pane.
  • Page 115 [Reset to default] to return to the factory default setting. Setting Up [Print Density] Select [Print density] from the [System parameters] menu. The Print density selections will display in the right pane. 3.8 System Parameter Setup (Print Services on Web, 6030/6050)
  • Page 116 Enter a positive or a negative number between -99 and +99 to set up the default print density. Larger negative numbers lighten the prints. Higher positive numbers darken the prints. The factory default setting is [0]. Press the [Apply] button to save the new setting, [Cancel] to revert to the existing setting, or [Reset to default] to return to the factory default setting.
  • Page 117 [Reset to default] to return to the factory default setting. Setting Up [Extension] Select [Extension] from the [System parameters] menu. The Extension selections will display in the right pane. 3.8 System Parameter Setup (Print Services on Web, 6030/6050)
  • Page 118 Select the required format from [Data format]. As required, add or delete an extension: Add an extension To add a new extension, enter an extension name of eight characters or less in the text field, and then click the [Add] button. Delete an extension To delete an extension, click the [Delete] button.
  • Page 119 Press the [Apply] button to save the new setting, or press [Cancel] to revert to the existing setting. 3.8 System Parameter Setup (Print Services on Web, 6030/6050) If the time selections are not displayed, drag the bottom scroll bar to the...
  • Page 120: System Parameter Setup (Web Printer Management Tool, 6050A)

    System Parameter Setup (Web Printer Management Tool, 6050A) • Consult Web Printer Management Tool help system for details on setting up system parameters for the 6050A. Chapter 3 Printer Setup...
  • Page 121: Printing A Configuration List (6030/6050)

    SET: to Print. From Print Services on Web Start Print Services on Web, log in as Administrator, and select the [Properties] tab. 3.10 Printing a Configuration List (6030/6050) Press the < > key with [PORT SETTING] displayed. Select [PRINT CONFIG] with the < > key, and then press the <...
  • Page 122 Select [Print Settings] in the System parameters menu. The current print settings will display in the right pane. Using the scrollbar on the right side of the window, scroll to the bottom of the Print Settings list, and then select the [Print] button. The printer will print a configuration list that is identical to the list from the printer control panel.
  • Page 123 An example of the configuration list (settings printout) is shown below. 3.10 Printing a Configuration List (6030/6050)
  • Page 124 Description of the Configuration List Contents The contents of configuration list are explained below. Displayed Item H/W CONFIG Model Software Version RAM Total Segment Memory Work Memory Frame Memory Harddisk Option H/W Finisher Model S/W CONFIG PostScript Network Scan Key Install Key PORT SETTING ETHERNET TCP/IP...
  • Page 125: Printing A Configuration List (6050A)

    3.11 Printing a Configuration List (6050A) The procedures below explain how to print a configuration list that shows the hardware and software configuration, communication parameter (port) settings, and system parameter settings of the printer. This list may be printed from either the printer control panel or Web Printer Management Tool.
  • Page 126 Select the [Test Print] sub-tab that appears. Depending upon your information requirements, click on the [Minimal], [Normal], [Full], or if PostScript is available, [PostScript] test print buttons. Explanations of each of these options are available from the Web Printer Management Tool interface. Chapter 3 Printer Setup...
  • Page 127 An example of the configuration list (settings printout) is shown below. 3.11 Printing a Configuration List (6050A)
  • Page 128 Description of the Configuration List Contents The contents of the configuration list are explained below. Category Controller Configuration Displays data such as controller date/time, firmware version, size of hard disk, etc. Optional Controller Displays which optional features of the 6050A have been activated. Features Print Engine Displays data such as the set resolution of the 6050A, power saver...
  • Page 129: Software Option (Print Services On Web, 6030/6050)

    Web, 6030/6050) The [Software Option] selection on the Print Services on Web [Properties] tab displays all installed optional software and related Feature Key (Key Install Key) information, for example, for the PostScript Driver. 3.12 Software Option (Print Services on Web, 6030/6050)
  • Page 130: Software Option (Web Printer Management Tool, 6050A)

    3.13 Software Option (Web Printer Management Tool, 6050A) Similar to the [Software Option] selection under the Print Services on Web [Properties] tab, the the [Features] selection under the [Configuration] tab in Web Print Management Tool allows for the display of what features are currently installed on the 6050A.
  • Page 131: Change Password (Print Services On Web, 6030/6050)

    Enter the new password in the [New password:] field. Enter the new password again in the [Confirm New Password:] field. Click the [Apply] button to save the change, or [Cancel] to undo it. 3.14 Change Password (Print Services on Web, 6030/6050)
  • Page 132: Change Password (Web Printer Management Tool, 6050A)

    3.15 Change Password (Web Printer Management Tool, 6050A) Maintain a record of the new password in a secure location. Select the [Utilities] tab on the main navigation bar, then click on the [Password] sub-tab. Enter the current printer password in the [Enter the current printer password:] field.
  • Page 133: Change Default Language (Print Services On Web, 6030/6050)

    Select the required language selection from the pull down list. Click the [Apply] button to save the change, or [Cancel] to undo it. Power the machine off and then on for the change to take effect. 3.16 Change Default Language (Print Services on Web, 6030/6050)
  • Page 134: Change Default Language (Web Printer Management Tool, 6050A)

    3.17 Change Default Language (Web Printer Management Tool, 6050A) Web Printer Management Tool allows the user to change the language displayed when it is started. The language can be changed to English, Italian, French, Spanish, South American Portuguese, German or Russian. Select the [ Configuration] tab on the main navigation bar, then select the [Printer] sub-tab.
  • Page 135: Chapter 4 Logical Printer Setup And Operation (6030/6050 Only)

    Chapter Chapter 0 Logical Printer Setup and Operation (6030/6050 only) Chapter 4...
  • Page 136: Creating A New Logical Printer

    Start the web browser and log in to Print Services on Web. Enter the Administrator mode, and then select the [Print Setup] tab. Chapter 4 Logical Printer Setup and Operation (6030/6050 only)
  • Page 137 Select the data format for the new logical printer from the [Data format] menu. The selections include [Versatec], [HP-GL], [TIFF], [CALS], and optionally, [PS/PDF]. 4.1 Creating a New Logical Printer The logical printers are pre-configured in the factory to their default print settings.
  • Page 138 Use the scrollbar on the right side of the window to scroll through the [Logical printer information] list. To print a list of the logical printer settings, scroll to the bottom of the [Logical printer information] list and click the [Print] button. Chapter 4 Logical Printer Setup and Operation (6030/6050 only)
  • Page 139: Defining The Print Settings

    Defining the Print Settings The next step, after creating a logical printer, is to set up the parameters that define how it will process print jobs. These parameters are located at the left side of the screen in the [Print Setup] menus ([Media setting], [Input setting], [Output setting], [Transform], [Pen setting], and [Command setting]).
  • Page 140: Logical Printer Print Settings

    Specifies the media size series for the input and output data, and the media. Sets up the input size mapping, and whether to enable or disable the media mapping. Chapter 4 Logical Printer Setup and Operation (6030/6050 only) PS/PDF Media Series Size/media Mapping Media Source...
  • Page 141 [Print Setup] Menu Item Menu Media setting Media Source (continued) Media Type User-Defined Size Sets up the user defined size. Input setting Input Option Input Size Margin Output setting Priority Title Block Split Drawing Message Option Printed Copy Output Option Size Recognition Transform Transform...
  • Page 142 Selects the processing language (HP-GL/ HP-GL2) for the HP-GL data. Enables and disables the PS command. Enables and disables the EOP command. Chapter 4 Logical Printer Setup and Operation (6030/6050 only) Data Format All (see Note) HPGL, Versatec TIFF CALS...
  • Page 143: Media Series

    Media Series This parameter sets up the media size series for the input size, output size, and media size. Each item can be set to a different media size series. Settings The settings are as follows. All of the default settings are [ISO A]. Menu Item Input size Output size...
  • Page 144 Special A ARCH ANSI ARCH-30 Refer to "9.1 Main Specifications (6030/6050)" for the 6030/6050 and "9.2 Main Specifications (6050A)" for the 6050A for details on the media sizes. Standard Size A0 to A4, U0 to U4, A0L to A4L Input size: B0 to B4, BU0 to BU4, B0L to B4L...
  • Page 145: Size/Media Mapping

    Size/Media Mapping Standard size images and user-defined images can be enlarged and reduced to fit standard and user-defined output sizes. This is known as "Size Mapping". It is also possible to specify which roll media is to be used based on the output size.
  • Page 146 The paper size selected will differ in accordance with the [Media size] parameter set for the Media series. Chapter 4 Logical Printer Setup and Operation (6030/6050 only) Output on the A3 roll media Output on the A2...
  • Page 147 Example When the mapping table is set up as shown below, an image with an input size of A3 will be printed as follows. Media Mapping Input size Size Mapping Size mapping is applied to the image with an input size of A3, which is then enlarged to an A2 output size (enlarged by 141.4%).
  • Page 148: Media Source

    The default setting is [AUTO]. [JOB] The paper tray command in the print data takes priority. [Controller] The setting made on the printer control panel takes priority. The default settings is [JOB]. Chapter 4 Logical Printer Setup and Operation (6030/6050 only)
  • Page 149: Media Type

    Media Type Determines the default media type selection for printing. This setting is valid when a different type of media of the same size is loaded in the printer. [ANY] is set for this under normal circumstances. When the media type specification command is already set up in the job data from the host, the host command has priority.
  • Page 150: User-Defined Size

    Sets up the length of the user-defined media. Refer to the table on the following page for the range in which the sizes can be set. Chapter 4 Logical Printer Setup and Operation (6030/6050 only)
  • Page 151: Input Option

    Input Option Sets up the input image size. Two judgment methods are available for input image size. • Automatic (AUTO) Calculates the coordinates of the input image and automatically determines the nearest media size. • Specify Size Enables the user to manually select the media size of the input image. The media size can be selected from standard sizes and user-defined sizes.
  • Page 152 A value that subtracts 1 from the length of the standard size will be set for [Connect]. For example, in the event of 4A3, 3 will be set for the [Connect]. Connect = 3 Chapter 4 Logical Printer Setup and Operation (6030/6050 only)
  • Page 153: Input Size Margin

    Input Size Margin Specifies the top, bottom, left, and right margin settings for determining input sizes. Plus (+) values represent margins outside of the media size, and minus (–) values represent margins inside the media size. The size that includes (excludes) these margins is established as the input judgment size.
  • Page 154 A3, the A2 size is determined. When printing is performed on A2 paper × A2: 410 × (420 594), a margin will be located at the top, bottom, left and right. Chapter 4 Logical Printer Setup and Operation (6030/6050 only) Description...
  • Page 155: Plot Area

    Plot Area Enables the print range (the plot area) to be specified based on the input image information. The plot area can be set up so that the image prints in the center of the media (Auto Layout) or is offset (Set Offset Value). If part of the image overlaps the margin when offset is specified, it will be cut off.
  • Page 156 The offset value can be set within a range of –999 to 999 Sets the amount of offset up and down. The offset value can be set within a range of –999 to 999 Chapter 4 Logical Printer Setup and Operation (6030/6050 only)
  • Page 157 in the Y direction. Size Descriptions of Area Mode The area modes are described below. ADAPTED FIXED (HP-GL) FIXED (HP-GL/2) IP AREA IW AREA RASTER FIRST 4.3 Logical Printer Print Settings OFFSET – – 999 to 999) 999 to 999) –10 The data range of the input image is set as the print range (see Fig.1).
  • Page 158 Fig.1. (ADAPTED) Input image (0,0) Fig.2. (FIXED) (+X1,+Y1) Input image (0,0) Fig.3. (IP AREA and IW AREA) Input image (0,0) Output image Auto Layout: [YES] Output image Auto Layout: [YES] The area specified with the [IP Command] or [IW Command]. Output image Auto Layout: [YES] Offset...
  • Page 159 Fig.4. (FIRST) (0,0) Output image Offset Auto Layout: [YES] Auto Layout: [NO] Fig.5. (FIRST ) (0,0) Input image Output image 4.3 Logical Printer Print Settings...
  • Page 160: Priority

    Menu Item PRIORITY Description Sets one of the following as the printing priority. The default setting is [NORMAL]. [LOW] Low printing priority [NORMAL] Normal (standard) printing priority [HIGH] High printing priority Chapter 4 Logical Printer Setup and Operation (6030/6050 only)
  • Page 161: Title Block

    Title Block The setting determines whether or not to rotate images 180 degrees. This setting is used to change the image orientation to ensure correct folding. Settings The available settings are as follows. Menu Item Media Size Title Block 4.3 Logical Printer Print Settings Description Determines whether or not to rotate images for each media size.
  • Page 162: Split Drawing

    The default settings is [1,189 mm]. Determines whether or not a page number will be printed. The page number will be printed in the format [present page number:total number of pages]. The default setting is [Off]. Chapter 4 Logical Printer Setup and Operation (6030/6050 only)
  • Page 163 Item Page margin Alignment mark printing 4.3 Logical Printer Print Settings Description Determines whether or not the page margin will be present, and sets the margin where the pages are joined within a range of 0 to 90 mm. The default settings is [0 mm]. Determines whether or not to print positioning marks.
  • Page 164: Message Option

    Determines whether or not to print error messages. The default setting is [ON]. Determines whether or not to print label messages. The default setting is [OFF]. Chapter 4 Logical Printer Setup and Operation (6030/6050 only) Top right 5 mm Bottom right...
  • Page 165 Menu Item Date Message Display Position 4.3 Logical Printer Print Settings Description Determines whether or not to print date messages. The default setting is [OFF]. The date format is [Year/Month/Day Hour:Minutes]. Example: [2006/01/02 14:56] Sets up the location where the message(s) will be printed.
  • Page 166: Printed Copy

    The default setting is [1]. [JOB] The copy count command in the job data takes priority. [Controller] The setting made on the printer control panel takes priority. The default setting is [JOB]. Chapter 4 Logical Printer Setup and Operation (6030/6050 only)
  • Page 167: Output Option

    Output Option Sets up the output size. The following two judgment methods are available for output image size. • Automatic (AUTO, OTHER, MIX, MIX2) Determines the most suitable output size based on the input size and the size mapping table. It also determines the roll media size to use based on the output size and the media mapping table (or automatically.) •...
  • Page 168 Sets the top margin in a range from 0 to 999 mm when the [Margin] parameter is set to [ALL] or [LONG]. Sets the bottom margin in a range from 0 to 999 mm when the [Margin] parameter is set to [ALL] or [LONG]. Chapter 4 Logical Printer Setup and Operation (6030/6050 only)
  • Page 169 • Media Size Input image that is longer than the standard size • Connect Connect = 3 4.3 Logical Printer Print Settings Output image • Margin Paper feed direction In the case of [AUTO] Output in a size that is the standard shape increased in a multiple of integers.
  • Page 170: Size Recognition

    In the case of an input image that is longer than the standard size (example: 420 × 650mm) Settings Output image Chapter 4 Logical Printer Setup and Operation (6030/6050 only) Standard shape priority Output on the standard size (example A1: 594 × 841mm) Increased standard shape...
  • Page 171 The settings for this function are as follows. Menu Item Size Recognition 4.3 Logical Printer Print Settings Description Sets up the size recognition priority mode. The default value is [Standard long size output]. [Standard long size Outputs images that are within the A0 output] size, but exceed the standard size, on one size larger standard shape paper.
  • Page 172: Color Option

    Can draw visible lines on a black background. [DISABLE] Draws all lines with the black pen. Lines are not visible when they are drawn on a black background. The default setting is [ON] for HP-GL; [OFF] for Versatec. Chapter 4 Logical Printer Setup and Operation (6030/6050 only)
  • Page 173: Transform

    Transform Enables or disables the auto scale (automatic enlargement/reduction), mirror image, and 90-degree rotation functions. Auto Scale Input image Mirror Image Input image 4.3 Logical Printer Print Settings Output image Output image...
  • Page 174 Rotates the output image by 90 degrees. [DISABLE] Outputs the image in the normal manner. This setting is only valid when the [Media Size] parameter of [Input Option] is set to anything other than [Auto]. Chapter 4 Logical Printer Setup and Operation (6030/6050 only)
  • Page 175: Define Single Pen

    Define Single Pen Defines the width, color, end style, and joint style pen attributes for HP-GL data. Click the [Change] button to edit the attributes of a pen. The screen below will display. Click [Apply] to save your changes. Settings The settings for this function are as follows.
  • Page 176 The default setting is [MITER]. Refer to the illustrations on the next page for more details. This setting is only valid for HP-GL and HP-GL/2 EA, EP, ER, FP, RA, RR, and PE. Chapter 4 Logical Printer Setup and Operation (6030/6050 only) ×...
  • Page 177 Line width Half the line width Half the line width Line width Half the line width Half the line width Line width Half the line width Half the line width Joint style 4.3 Logical Printer Print Settings SQUARE The normal method for ending lines. ROUND Rounds off both ends of the line with a half radius of the line width.
  • Page 178 Extends the joint by half the line width, and connects the top and outer edges of both lines. MITERED/BEVELED Extends the joint by the length calculated from the line width and Miter Limit, and connects the top. Chapter 4 Logical Printer Setup and Operation (6030/6050 only)
  • Page 179: Define Multi Pen

    Define Multi Pen Sets up the line width, color, end style, and joint style pen attributes for HP-GL data for multiple pens. The same parameters will be set for all other pen numbers within the specified range. Settings The settings for this function are as follows. Menu Item Pen No.
  • Page 180: Pen Option

    The setting for this function is as follows. Menu Item Enlarge/reduce pen width Description [ENABLE] Changes the pen width based on the enlargement/reduction ratio. [DISABLE] The pen width remains unchanged. The default setting is [DISABLE]. Chapter 4 Logical Printer Setup and Operation (6030/6050 only)
  • Page 181: Emulation

    Emulation Selects the processing language for the HP-GL format only. Settings The settings for this function are as follows. Menu Item Emulation 4.3 Logical Printer Print Settings Description Sets the processing language at either [HP-GL] or [HP-GL/ The default setting is [HP-GL].
  • Page 182: Ps Command

    Settings The available settings are as follows. Menu Item PS command Description [DO NOT IGNORE] Enables the PS command. [IGNORE] Disables the PS command. The default setting is [DO NOT IGNORE]. Chapter 4 Logical Printer Setup and Operation (6030/6050 only)
  • Page 183: Eop Command

    EOP Command Enables and disables the EOP command for HP-GL data only. Settings The settings for this function are as follows. The default value for all parameters is [Enable]. Menu Item SP:Pen0 PG:Adv Page 4.3 Logical Printer Print Settings Description Enables or disables the SP:Pen0 command.
  • Page 184: Vcgl Pen Style (Vcgl Define Pen)

    Sets the end of the line to [SQUARE], [ROUND], [EXTEND], or [TRIANGLE]. The default setting is [SQUARE]. Refer to "End style" for further details. Sets broken line processing to [WRAP] or [NO WRAP]. The default setting is [NO WRAP]. Chapter 4 Logical Printer Setup and Operation (6030/6050 only)
  • Page 185 Example Broken line style NO WRAP Each dot represents the start of the broken line. Lines printed with the use of the broken line style shown in the example will be printed as a non-broken line, as shown in the illustration on the left. This is due to the fact that the dot appears before the line is broken, and this constitutes the starting point for printing another line.
  • Page 186: Vcgl Pen Width

    1 = 0.0635 mm. The actual width of the line will be n 0.0635, with the line width set to n. The default setting is [2]. Text may not print clearly if the line width is set to [1]. Chapter 4 Logical Printer Setup and Operation (6030/6050 only) ×...
  • Page 187: Vrf Define Pen (Define Single Pen)

    VRF Define Pen (Define Single Pen) Sets the pen attributes for VRF data only. Click the [Change] button to define the attributes for a pen. The VRF Define Pen menus will display on the right side of the screen. Settings The settings for this function are as follows.
  • Page 188 Sets the end of the line to [SQUARE], [ROUND], [EXTEND], or [TRIANGLE]. The default setting is [SQUARE]. Refer to "End style" for further details. Sets the line color to [BLACK] or [WHITE]. The default setting is [BLACK]. Chapter 4 Logical Printer Setup and Operation (6030/6050 only)
  • Page 189: Vrf Define Multi Pen

    VRF Define Multi Pen Sets the pen attributes for multiple pens for VRF data only. The same parameters will be set for all other pen numbers within the specification range. Settings The settings for this function are as follows. Menu Item Pen No.
  • Page 190: Tiff Option

    Uses the resolution embedded in the TIFF data. [CONTROLLER]Uses the resolution set here. Sets the resolution within a range of 30 to 3000 (dpi) when the [CONTROLLER] parameter has been specified. Chapter 4 Logical Printer Setup and Operation (6030/6050 only)
  • Page 191: Cals Option

    CALS Option Determines whether to enable or disable the [Rotate] command for CALS data only. Settings The settings for this function are as follows. Menu Item Specify Output Direction 4.3 Logical Printer Print Settings Description [ENABLE] Enables the [Rotate] command. [DISABLE] Disables the [Rotate] command.
  • Page 192: Ps/Pdf Option

    [Normal] Adds 4 mm margins to the top, bottom, left, and right sides of the media. Print data is placed inside the margins. [Extend] No margins are added. Images will be printed to the edge of the page. Chapter 4 Logical Printer Setup and Operation (6030/6050 only)
  • Page 193: Logical Printer Operations

    Logical Printer Operations This section explains the procedures for performing the following using Print Services on Web. • Selecting the Media Type • Using Media Other Than the Default Series • Changing Output Roll Media for an Entire Job • Reduction and Enlargement Using Size Mapping •...
  • Page 194: Selecting The Media Type

    If a media other than the specified type is loaded after this setting is made, a [No Paper] error will be triggered. Refer to "4.3 Logical Printer Print Settings" for details. Chapter 4 Logical Printer Setup and Operation (6030/6050 only)
  • Page 195: Using Media Other Than The Default Series

    • Refer to the "Media Series" section of "4.3 Logical Printer Print Settings" for details on available functions. • Refer to "9.1 Main Specifications (6030/6050)" for the 6030/6050 and "9.2 Main Specifications (6050A)" for the 6050A for details on the media sizes for each media group.
  • Page 196: Changing Output Roll Media For An Entire Job

    [PLT02H] logical printer settings Media Size Image Size Logical printer [PLT01H] specified Logical printer [PLT02H] specified Rotated by 90 degrees Chapter 4 Logical Printer Setup and Operation (6030/6050 only) Media Size Output on the A2 roll media Output on the A1 roll media...
  • Page 197: Reduction And Enlargement Using Size Mapping

    Reduction and Enlargement Using Size Mapping Reduction and enlargement can be performed using the size mapping table. The size mapping table establishes relationships between input image sizes and output image sizes. It enables users to enlarge or reduce prints automatically. The size mapping table is set up using the logical printer’s [Size/media mapping] selection.
  • Page 198: Printing Long Documents

    • All output is carried out on roll media when [OTHER] has been selected. Cut sheet cannot be used. Output image Chapter 4 Logical Printer Setup and Operation (6030/6050 only) In the case of [AUTO] Output in a size that is the standard shape increased in integers.
  • Page 199: Print Services On Web: Job And Log

    Print Services on Web: Job and Log The Print Services on Web [Job and Log] tab enables the user to perform the following. • Display the Print Queue • Cancel and Change the Priority of Jobs • Manage the Job and Error Logs •...
  • Page 200 On standby for job processing. [Printing] Printing in progress. Displays [High], [Normal] or [Low] as the priority. Displays the name of the document. [---] is displayed when the name is unknown. Chapter 4 Logical Printer Setup and Operation (6030/6050 only)
  • Page 201 Displayed Item Printer Name Size Change Job 4.5 Print Services on Web: Job and Log Description Displays the name of the destination logical printer. [---] is displayed when the name is unknown. Displays the size of the job in KB. Changes the priority of or cancels a job.
  • Page 202: Cancel And Change The Priority Of Jobs

    A list of all jobs that are printing and queued will display on the right side of the screen. Refer to "2.3 Print Services on Web (6030/6050)" for details on starting up Print Services on Web. Chapter 4 Logical Printer Setup and Operation (6030/6050 only)
  • Page 203 Click the [Change] link located on the right side of the job that you want to cancel or change. The [Change job] page will display. To cancel the job, click the [Execute] button. To change the priority of the job, select either [High], [Normal], or [Low] from the [Priority] menu, and then click the [Apply] button.
  • Page 204: Manage The Job And Error Logs

    It is only possible to display a list of jobs on the User page. All other operations must be carried out on the Administrator page. Job log and error log management also can be performed from the printer control panel. Refer to "5.5 Managing the Job and Error Logs (6030/6050 only)" for more information. Job Log The job log is a record of all completed print jobs.
  • Page 205 Select [Job Log] from the [Log list] menu. A list of processed jobs will display on the right side of the screen. To display a subset of the logged print jobs: • Enter a range in the [Job number] fields, and then click the [Update] button - or - •...
  • Page 206 Chapter 4 Logical Printer Setup and Operation (6030/6050 only)
  • Page 207 Select [Job log] from the [Log list] menu. A list of completed jobs will display on the right side of the screen. To display a subset of the logged print jobs, enter a range in [Job number] or specify the period in the [Print log from:] fields, and then click the [Update] button.
  • Page 208 Select [Job Log] from the [Log list] menu. A list of log information will display in the right pane. Chapter 4 Logical Printer Setup and Operation (6030/6050 only)
  • Page 209 Click [Change settings]. The [Job log setup] screen will display. Select [ON] as the [Auto Print Setup] selection, and then click [Apply]. The job log will print automatically whenever sufficient job log entries accumulate. Delete the Job Log Start Print Services on Web, log on as Administrator, and display the [Job and Log] tab.
  • Page 210 Chapter 4 Logical Printer Setup and Operation (6030/6050 only)
  • Page 211 Click the [Delete log] button. A confirmation popup will display. Select the [OK] button to delete the job log, or [Cancel] to retain the log. Save the Job Log Start Print Services on Web, log on as Administrator, and display the [Job and Log] tab.
  • Page 212 Chapter 4 Logical Printer Setup and Operation (6030/6050 only)
  • Page 213 Further define the job log, if necessary, using the [Print log from], [Job number], [Date], and [Display] selections, and then click the [Save into file] link. The job log will be saved in a comma-separated value (CSV) format, and displayed as in the figure below. Display the Error Log The Error Log is a record of information about the errors that occurred during job processing.
  • Page 214 The procedures for saving, deleting, and printing the error log(s) are the same as those for managing the job log(s). Refer to the relevant job log procedure when you need to change or save the error log data. Chapter 4 Logical Printer Setup and Operation (6030/6050 only)
  • Page 215: Print Services On Web: Status

    To access Help, click the [?] button in the upper, right corner of the screen. Display Printer Status This function displays the status of the 6030/6050 Wide Format Printer and Copier/Printer. Procedure Start Print Services on Web and display the [Status] tab on either the User page or the Administrator page.
  • Page 216 • Meter 2: The total length (in feet and meters) of media printed until now • Meter 3: The total number of stamp prints made until now Chapter 4 Logical Printer Setup and Operation (6030/6050 only) Description...
  • Page 217 The printer is out of media. Load the required media. A system error has occurred in the printer. Switch off the printer power, and then switch it on again. If the problem does not recover, contact your Xerox Service Representative.
  • Page 218: Start And Stop Job Reception, Printing, And The Print Service

    Jobs received from clients are placed in a [Queued] status and are spooled on the hard disk. Starts the printing process. Suspends both job reception and printing. Starts both job reception and printing. Chapter 4 Logical Printer Setup and Operation (6030/6050 only)
  • Page 219: Print Services On Web: Tools

    These procedures can only be performed from the Administrator mode. Test printing also can be performed from the printer control panel. Refer to "5.4 Test Printing (6030/6050 only)". • The Print Services on Web Help function provides step-by-step instructions for performing the tasks described below. It also provides lists and descriptions of the items and fields that appear on the screen.
  • Page 220: Print A Diagnostic Report

    Specify the inclusive report dates using the [Range (Date: YYMMDD):] field, and then click [Save]. A dialog box will display. You may choose to open and view the report or save it. Chapter 4 Logical Printer Setup and Operation (6030/6050 only)
  • Page 221: Manual Feed Printing

    Procedure Set [Media Source] for the logical printer to [Manual]. Send the print job to the 6030/6050 Wide Format Printer or Copier/ Printer. The following message will display on the printer control panel if there is no media in the (MSI) Multi Sheet Inserter/Manual Feed Unit.
  • Page 222 Chapter 4 Logical Printer Setup and Operation (6030/6050 only)
  • Page 223: Chapter 5 Additional Operations From The Printer Menu

    Chapter Chapter 0 Additional Operations from the Printer Menu Chapter 5...
  • Page 224: Introduction

    Introduction The printer control panel’s menus enable the user to perform the following major tasks: (On the 6030/6050 Wide Format) • Set up the system parameters using the [SYSTEM PARAMETERS] submenu. • Set up the communication parameters using the [PORT SETTING] submenus.
  • Page 225: Printer Control Panel Menu (6030/6050)

    <Set> key to accept the previous selection. It is recommended that the procedures covered in this chapter be performed using Print Services on Web. 5.2 Printer Control Panel Menu (6030/6050) Displays the previous menu item or value on the same menu level.
  • Page 226 [Network Port/Set] Menu Level 1 Level 2 SYSTEM Set Date PARAMETER AUTO ROLL SPA PAPER WIDTH Smoothing Low power mode1 Low power mode2 Sleep Mode Attention Light Print Density Job Recovery Net Cont. Time Level 3 Level 4 Set Date YY/MM/DD hh: mm Roll Tray Roll Tray...
  • Page 227 Level 1 Level 2 PORT TCP/IP SETTING 5.2 Printer Control Panel Menu (6030/6050) Level 3 Level 4 Ethernet Setting Ethernet Setting AUTO 10BASE_T 100BASE_T Default Parser Default Parser HPGL TIFF CALS VERSATEC *PS/PDF IP Address IP Address xxx.xxx.xxx.xxx MASK Value MASK Value xxx.xxx.xxx.xxx...
  • Page 228 Level 1 Level 2 PORT SERIAL SETTING CENTRO (optional) Level 3 Level 4 Handshake Handshake XON/XOFF HARDWARE ENQ-ACK SOFTWARE (ENQ-ACK and SOFTWARE only with HPGL) Default Parser HPGL Baud Rate Baud Rate 1200 2400 4800 9600 19200 Parity Parity NONE EVEN Data Bit Data Bit...
  • Page 229 VIEW The [Starting day to ending day] parameter for log management is specified in the YYMMDD format; (YY: 00 to 99, MM: 01 to 12, DD: 01 to 31) 5.2 Printer Control Panel Menu (6030/6050) Level 3 Level 4 Report Offline...
  • Page 230 [Print Setup] Menu The Print Setup menu should be used immediately after loading new media or changing the type and/or size of media in the media drawers or the bypass (MSI). Level 1 Level 2 PRINT MEDIA SETUP *Roll1 *Roll2 *Roll3 *Roll4 *Bypass...
  • Page 231: Printer Control Panel Menu (6050A)

    Printer Control Panel Menu (6050A) The following is a list of the menus and submenus which can be accessed by pressing the <Menu> key and placing the printer in the offline mode. As a reminder, the following buttons are used to navigate the printer control panel menus.
  • Page 232 [System Settings] Menu TCP/IP System Settings Date/Time Timers *xxx.xxx.xxx.xxx IP Address IP Subnet Mask *xxx.xxx.xxx.xxx IP Gateway *xxx.xxx.xxx.xxx *Enable DHCP *Disable *Enable RARP/BOOTP *Disable *MM/DD/YYYY HH:MM Power *5-240 Min. Management/ Low Power Power *5-240 Min. Management/ Sleep Mode Chapter 5 Additional Operations from the Printer Menu...
  • Page 233 [Utilities] Menu Utilities Test Print Billing Meters Shut Down 5.3 Printer Control Panel Menu (6050A) *Printer Configuration *Printer Settings *Pen Palettes *All Meter 1 #### Meter 2 #### *Shut Down *Restart...
  • Page 234 [Print Setup] Menu The Print Setup menu should be used immediately after loading new media or changing the type and/or size of media in the media drawers or the bypass (MSI). Print Setup Tray Fuser Media Roll *1,2 *Enable Roll *3,4 *Disable Bypass *Enable...
  • Page 235: Test Printing (6030/6050 Only)

    MENU TEST PLOT TEST PLOT Plot Size Plot Size TEST PLOT SET : to Print. 5.4 Test Printing (6030/6050 only) Press the < > key with [TEST PLOT] displayed on the parameter selection screen. Press the < > key. Select the size of the media to print with the use of the <...
  • Page 236: Managing The Job And Error Logs (6030/6050 Only)

    JOB LOGGING JOB LOGGING JOB LOG JOB LOG SETTING SETTING Auto Mode 5.5 Managing the Job and Error Logs (6030/6050 only) Press the < > key with [JOB LOGGING] displayed. Press the < > key with [JOB LOG] displayed. Select the relevant operations with the use of the <...
  • Page 237 PRINT SET : to Print. CLEAR SET : to Clear. 5.5 Managing the Job and Error Logs (6030/6050 only) < > key. 2. Select either [ON] or [OFF] with the use of the < > and < > keys when [Auto Mode] has been specified, and then press the <Set>...
  • Page 238: Error Log (6030/6050 Only)

    Error Log (6030/6050 only) This section explains the procedures for printing and clearing the error log. Procedure MENU JOB LOGGING JOB LOGGING ERROR LOG ERROR LOG PRINT PRINT LOG 020423 – 020605 PRINT SET : to Print. Press the <...
  • Page 239 JobNo Data&Time Task Name 02/04/17 15:49:30 OUTPUT 02/04/22 20:38:05 HP PARSER 5.5 Managing the Job and Error Logs (6030/6050 only) When [CLEAR] is selected Press the <Set> key when [SET: to Clear.] is displayed. The error log will be deleted. ErrNo...
  • Page 240: Reprinting (6030/6050 Only)

    Reprinting (6030/6050 only) This function reprints the file that was most recently printed. The copy quantity (1 to 99) also can be specified. Reprinting can not be performed if a copy job has been performed after the print job. In order for reprinting to work, a job must be saved in memory.
  • Page 241: Billing Meter Confirmation (6030/6050)

    VIEW METER 1 METER 1 986754 5.7 Billing Meter Confirmation (6030/6050) Description Displays the total area of media printed (in square feet or meters). Displays the total length of media printed (in feet and meters). Displays the total number of stamp prints.
  • Page 242: Billing Meter Confirmation (6050A)

    Billing Meter Confirmation (6050A) This feature displays the billing meters on the printer control panel. Quantities of up to nine digits can be displayed. Menu Item METER 1 METER 2 Procedure MENU UTILITIES UTILITIES Billing Meters VIEW Meter 1 Meter 1 9867 Description Displays the total area of media printed (in square feet or meters).
  • Page 243: Print Setup Menu

    Print Setup Menu This section explains the items which can be set up from the [PRINT SETUP] Menu on the printer control panel. Menu Item Media Tray Fuser Setting Up Media The media type, weight, and size series must be set up whenever you load new media in the machine or change the type and/or size of the media in the trays or in the MSI/(Multi Sheet Inserter/Manual Feed Bypass).
  • Page 244 Media The media Size Series and sizes that can be set up are as follows. Size Series ISO A series SP. A-1 series Type Roll1 Bond Roll2 Vellum Roll3 Film Roll4 Bypass Weight Light Ordinary Heavy Series Sp. A-1 Sp. A-2 Trim Eligible Media ×...
  • Page 245 Size Series SP. A-2 series ARCH ANSI The media [Weight] can been specified as follows: Media set to [Light] Media set to Ordinary [Ord.] Media set to [Heavy] Bond (20-29lb./ Procedure <Menu> key Ready to print MENU NETWORK/PORT SET < >...
  • Page 246 The [NETWORK/PORT SET] menu screen will display if the < pressed. < > key Print Setup Media < > < > key Media Roll1 < > key Media / Roll1 Type < > key Media Roll1 < > key Print Setup Media Selecting Values This section provides an example of setting up a media value.
  • Page 247 < > key Media / Roll1 Type : Bond < > < > key Media / Roll1 Type : Film <Set> key Media / Roll1 Type : Film < > key Media Roll1 5.9 Print Setup Menu Press the < > key. The specified value will display.
  • Page 248: Automatic Cut Using The Printer Control Panel

    5.10 Automatic Cut Using the Printer Control Panel This section describes how to cut the lead edge of the roll media. Procedure Print Settings Media < > key Media Roll1 < > key Media Roll2 < > key Media / Roll2 Type <...
  • Page 249 Press the < > key to return to the higher level. 5.10 Automatic Cut Using the Printer Control Panel...
  • Page 250 Tray This normally is set to [Auto] and should not be changed by the user. Consult your Xerox Service Representative before changing this setting. Fuser This normally is set to [Auto] and should not be changed by the user. Consult with your Xerox Service Representative before changing this setting.
  • Page 251: Chapter 6 Ethernet Print Service (For Unix)

    Chapter Chapter 0 Ethernet Print Service (for UNIX) Chapter 6...
  • Page 252: Overview Of The Ethernet Print Service

    This section explains how to set up the ftp and lpr commands and their formats. The file to be printed should be in a data format that the Xerox 6030/6050 Wide Format supports. Sending a file with a data format that is not supported will result in a print error.
  • Page 253: 6.2 Registering The Xerox 6030/6050 Wide Format Printer System

    SunOS 5.X In the case of SunOS 5.X, register the IP address and host name of the Xerox 6030/6050 Wide Format printer in the connected to the network.
  • Page 254: Registering The Remote Printer

    Xerox 6030/6050 Wide Format printer system. Refer to the "Main Printing Functions" section in "2.1 Overview of the 6030/ 6050/6050A Wide Format Printer" for logical printer. SunOS 5.X For SunOS 5.X, register the remote printer using the lpadmin command.
  • Page 255 = /usr/lpd/bsdlong rq = PLT20H device = dplt20hdplt20h: backend = /usr/lpd/rembak Be sure to specify a logical printer prepared in the 6030/6050 Wide Format printer system using rq. • Starting the Print Queue After finishing the settings, start the print queue using the qadm command.
  • Page 256: Registering The Xerox 6050A Wide Format Printer System

    Registering the Xerox 6050A Wide Format Printer System To print from the Xerox 6050A Wide Format printer system, the 6050A should be registered on the TCP/IP network. Host System Registration When the network information is managed by a name service such as NIS or DNS, the IP address and host name must be registered there.
  • Page 257: Registering The Remote Printer

    Executing the lpadmin command In the example below, the 6050A with the host name In contrast to the 6030/6050 with its plt00h, etc., the queue names for the 6050A with the Accxes controller are always given the name of [raw].
  • Page 258 = /usr/lpd/bsdlong rq = PLT20H device = dplt20hdplt20h: backend = /usr/lpd/rembak Be sure to specify a logical printer prepared in the 6030/6050 Wide Format printer system using rq. • Starting the Print Queue After finishing the settings, start the print queue using the qadm command.
  • Page 259: Printing Using The Ftp Command (6030/6050 Only)

    Connected to 6050WF. 220 6050 Wide Format FTP server ready Name (6050WF:ftpusr): Log on to the Xerox 6030/6050 Wide Format . Enter a user name (example: ftpusr) pre-registered in Xerox 6030/6050 Wide Format . You are prompted to enter a password.
  • Page 260 Enter the password of the user logged in at Step If the user information registered in the Xerox 6030/6050 Wide Format matches the logged-in user password, the login acceptance message is displayed. Password: 230 User logged in ftp> Specify a logical printer (example: plt00h). Enter the logical printer name using the cd subcommand.
  • Page 261 Specify the end. Enter the bye subcommand. A message indicating that ftp command has completed will be displayed. ftp> bye 221 Bye...see you later 6.4 Printing Using the ftp Command (6030/6050 only)
  • Page 262: Other Subcommands

    Displays directory; will display logical printers set from the control panel. If nothing is specified in the Xerox 6030/6050 Wide Format , only the logical printer at address 00 is displayed. Displays directory; will display logical printers set from the console panel.
  • Page 263: Message List

    Action: Enter the correct command. Control connection read error Status: A control connection error occurred in the FTP command wait status. Therefore, the connection was disconnected. Action: For another transfer, establish the connection again. 6.4 Printing Using the ftp Command (6030/6050 only)
  • Page 264 Status: Cannot accept data transfer because the system is overloaded. Action: Check the system for a media-out or media jam error. Wait a few moments and try again. If the error occurs frequently, restart the Xerox 6030/6050 Wide Format .
  • Page 265 Status: Failed to send the file transfer start message. Action: Wait a few moments and try again. Local resource failure: please start queuing Status: Cannot accept file transfer because queuing is stopped. Action: Start queuing and execute printing again. 6.4 Printing Using the ftp Command (6030/6050 only)
  • Page 266 Login failed Status: The user name and password do not match. Action: Log in again with the correct user name and password. No file found or invalid directory or permission problem Status: Failed to open the directory by the LIST command. Action: Wait a few moments and transfer the command again.
  • Page 267 Status: A user name or password was not specified by the USER or PASS command, or various commands were transferred without login. Action: Log in with a registered user name and password and try again. 6.4 Printing Using the ftp Command (6030/6050 only) [ ftpusr ] is registered...
  • Page 268: Printing Using The Lp/Lpr Command

    Specify the number of copies by entering a numeric value from 1 to 99 for the 6030/6050 or 1 to 199 for the 6050A. If more than 100 for the 6030/6050 or more than 1000 for the 6050A is specified, an error message is displayed and the specification is canceled.
  • Page 269 Usage Examples (6030/6050) The printing procedure using the lpr command is as explained below. Example 1:To print one copy of the file [drawa.hpgl] by logical printer [plt00h]. % lpr -Pplt00h drawa.hpgl Example 2:To print two copies each of the files [drawb.hpgl] and [drawc.hpgl] by logical printer plt00h.
  • Page 270 Usage Examples (6050A) The printing procedure using the lpr command is as explained below. Example 1:To print one copy of the file [drawa.hpgl] by logical printer [raw]. % lpr -Praw drawa.hpgl Example 2:To print two copies each of the files [drawb.hpgl] and [drawc.hpgl] by logical printer [raw].
  • Page 271: Printing (Lp Command) (For Sunos 5.X)

    Specify the number of copies by entering a numeric value from 1 to 99 for 6030/ 6050 and 1 to 999 for 6050A. If 100 or more is specified for the 6030/6050 or if more than 1000 is specified for the 6050A, an error message is displayed and the specification is canceled.
  • Page 272: Status Display (Lpq Command)

    Example 2:Display the status of a file transferred to logical printer [plt01h] ([lpq -P oklahoma] for 6050A). When the transfer of the [drawd.hpgl] file to the Xerox 6030/6050/6050A Wide Format is completed, the following message will be displayed. % lpq -Pplt01h...
  • Page 273 The information starting with Prt Size (KB) Format. cosmos: sending to oklahoma indicates the client status. The job ID for the client and the job ID for the Xerox 6030/6050/6050A Wide Forma 6.5 Printing Using the lp/lpr Command Status Prior.
  • Page 274: Cancel (Lprm Command)

    Specify the job ID of the job to be canceled. The status display command [ lpq ] displays job IDs. If this is omitted, all print jobs are canceled. Job IDs on the Xerox 6030/6050 Wide Format side and the client side are allocated separately.
  • Page 275 Example 2:Displays the status of logical printer [plt01h] and the canceling of job ID [123] This print job cannot be canceled because it is already in progress. % lpq -Pplt01h Job ID Sent By williams smith cosmos: sending to oklahoma Rank Owner smith...
  • Page 276 Example 4:Displays the status of logical printer [plt01h] and the canceling of job ID [416] in the client queue If the file transfer to the Xerox 6030/6050 Wide Format completes before the job in the client queue is canceled, the print job cannot be canceled. Display the Xerox 6030/6050 Wide Format print status, check the job IDs of the logical printer, and cancel the print job again.
  • Page 277: Message List (6030/6050 Only)

    Message List (6030/6050 only) This section explains messages that may be displayed during printing using the lpr command. These messages depend on the system because they are output from the client workstation. Cannot create /usr/spool/pltXXX/.seq Status: The lpd daemon on the client failed to create a control file.
  • Page 278 PLTXX can not dequeue Status: Failed to delete a job from logical printer PLTXX on the print service side. Action: Check by the lpq command whether the specified job has already changed from the wait status in the queue to the processing status. connection busy Status: Failed to establish connection for data transfer.
  • Page 279: Chapter 7 Maintenance

    Chapter Chapter 0 Maintenance Chapter 7...
  • Page 280: Loading Toner

    Loading Toner Load no more than one cartridge of toner when the message "Add Black Toner" first appears on the printer control panel. Observe the following precautions when handling the toner. • Handle the toner carefully to avoid spilling it on your clothing or around the machine.
  • Page 281 Toner supply lever 7.1 Loading Toner Take the toner cartridge out of the package and prepare it for loading. Shake the toner cartridge well to ensure that the toner will dispense properly. Open the lid of the toner supply port. Insert the left side notch, located at the bottom of the toner cartridge, into the end of the toner supply port.
  • Page 282 Slide the toner supply lever back and remove the cartridge. Close the lid on the toner supply port. • If the toner splashes around the toner supply port, clean the area after the loading is completed. • Toner may adhere to the bottom of t one r c ar tr i dg e.
  • Page 283: Chapter 8 Problem Solving

    Chapter Chapter 0 Problem Solving Chapter 8...
  • Page 284: Check The Control Panel(S)

    Check the Control Panel(s) When a machine failure is suspected, for example, when a print cannot be made or the image quality is defective, first check for error messages or error codes on the printer control panel. When an error code is displayed, press the < > and < > keys on the printer control panel at the same time.
  • Page 285: Poor Image Quality

    Poor Image Quality Perform the following corrective measures if the copies or prints display one of the image quality defects listed below. Image Quality Defect The print displays excessive background Some parts of the image did not print or are blurred The print is wrinkled 8.2 Poor Image Quality...
  • Page 286: Other Problems

    Other Problems Follow the instructions provided in the table to recover from the errors which are listed. Nothing is displayed on the printer control panel. It is not possible to insert documents Media jams occur frequently Error • Verify that the machine is connected to a correctly rated power supply, that the power plug is plugged in, and that the power switches and the circuit breaker switch are in the On...
  • Page 287: Printer Troubleshooting

    Refer to the "Input Size Margin" section of "4.3 Logical Printer Print Settings" for details on available functions. No paper error occurs even when paper has been set in place. (6030/6050 only) There is a chance that the paper actually set in place differs from the settings made in either [Media Mapping], [Media Type] or [Media Series].
  • Page 288 [Disable]. The [White Mode] is valid for HP-GL and Versatec data only. Refer to the "Color Option" section of "4.3 Logical Printer Print Settings" for details on available functions. Chapter 8 Problem Solving...
  • Page 289: Jams In The Feeder (Roll Media)

    Jams in the Feeder (Roll Media) Media jams in the roll feeder(s) are caused by incorrect media loading methods and defects in the media feeding mechanism. Reload the media according to the following procedure. Procedure 8.4 Printer Troubleshooting Open the media tray. Rewind the media on the roll from which the jam has occurred by rotating it toward you.
  • Page 290 The LED on the front of the media tray will illuminate, and the roll paper will be automatically positioned. Lift the lock lever located in the middle at the back of the scanner document table, and then close the document table (6030/ 6050 only). Chapter 8 Problem Solving...
  • Page 291: Jams In The Printer And Ejection Port

    Jams in the Printer and Ejection Port Remove media jams from the printer and ejection port following the instructions below. Procedure 8.4 Printer Troubleshooting Lift up the lever located on the left-hand side of the output unit. Use both hands to lift up the top of the unit. The top of the unit cannot be lifted if the scanner's lock has been released.
  • Page 292 Pull the green stopper to the front. Grasp the document table (6030/6050 only) with both hands and gently but firmly lower it into place. • Ensure that the weight of the...
  • Page 293: Chapter 9 Specifications

    Chapter Chapter 0 Specifications Chapter 9...
  • Page 294: Main Specifications (6030/6050)

    Main Specifications (6030/6050) Supported data formats • HP-GL formats: • Versatec formats: Versatec Random Format (VRF), Versatec Color Graphic • TIFF formats: • CALS formats: • PS/PDF formats: PostScript 3, PDF Version 1.3 (optional) Relationship between data formats and interfaces Some data types cannot be processed, based on the interface type.
  • Page 295 Maximum transfer speed:1 Mbps Maximum cable length:300 m Ethernet connection Server function: Maximum number of sessions:10 each for lpr and FTP 9.1 Main Specifications (6030/6050) 100Base-TX and 10Base-T (Transfer speed Manual selection, automatic selection) Ethernet version 2 EIA-232-E conformant to RS-232C serial...
  • Page 296 Standard sizes and drawing areas Standard Series size ISO A series ISO B series SP. A0 SP. A1 SP. A SP. A2 SP. A3 Dimensions × 1,189 mm (33.12 x 46.77") × 841 mm (23.36 x 33.12") × 594 mm (16.53 x 23.36") ×...
  • Page 297 Standard Series size ARCH ANSI ARCH 30 9.1 Main Specifications (6030/6050) Dimensions 36 x 48 inches (914.4 x 1219.2 mm) 24 x 36 inches (609.6 x 914.4 mm) 18 x 24 inches (457.2 x 609.6 mm) 12 x 18 inches (304.8 x 457.2 mm)
  • Page 298 Print Length • When the PS/PDF option is not in use Paper Type Paper Width Plain paper 36" 24" 18" 12" Vellum/Film • When the PS/PDF option is in use Paper Type Paper Width Plain paper 36" 24" 18" 12" Vellum/Film 512MB (Standard) 5,500mm...
  • Page 299 Frame memory - Maximum number of spools indicates the number of spools that are developed into bit map. The print entry data is spooled in the hard disk separately from the memories. 9.1 Main Specifications (6030/6050) Configuration 6030 Extended/ 6050 Standard...
  • Page 300: Main Specifications (6050A)

    CalComp 906/907/951/PCI • FileNET • NIRS • • VCGL • • Versatec Data Standards • Xerox Emulation 150 • • JPEG • Optional (Adobe ® ® ™ PostScript , PDF (1.6), DWF, BMP, JPEG 2000, PNG, GIF, DGN) Chapter 9 Specifications...
  • Page 301 Host system interfaces TCP/IP Physical interface: Maximum transfer speed:10/100/1000 Mbps Data link: Ethernet connection Server function: Maximum number of sessions:10 each for lpr and FTP 9.2 Main Specifications (6050A) 10-100Base-T (using manual selection) 10-100-1000Base-T (using auto selection with use of Cat6 cable) Cat6 cable required for gigabit data transfer Data transfer by lpr and FTP...
  • Page 302 Standard sizes and drawing areas Standard Series size ISO A series SP. A0 SP. A1 SP. A SP. A2 SP. A3 ARCH Dimensions × 1,189 mm (33.12 x 46.77") × 841 mm (23.36 x 33.12") × 594 mm (16.53 x 23.36") ×...
  • Page 303 Standard Series size ANSI 9.2 Main Specifications (6050A) Dimensions × 44 inches (863.6 x 1117.6 mm) × 34 inches (558.8 x 863.6 mm) × 22 inches (431.8 x 558.8 mm) × 17 inches (279.4 x 421.8 mm) × 11 inches (215.9 x 279.4 mm) Drawing area (dots) 20,400 x 26,400...
  • Page 304 Print Length Paper Type Paper Width Plain paper/ Vellum/Film Maximum print length = 50,000mm. 512MB (Standard) 3,600mm 7,272mm 14,544mm 29,088mm 58,176mm Chapter 9 Specifications...
  • Page 305: Media Specifications

    Media Specifications • For sharp image copying, use the media recommended by Xerox. • To prevent media jams or uneven printing, do not use creased, wrinkled, or curled media. • When using unusually flexible media, support the media as it comes out of the media ejection port so that it will not be pressed against the media table and result in jams.
  • Page 306: Machine Specifications (6030/6050)

    Less than 31 seconds (with A0 size) 99 sheets maximum A0 size: 5 sheets/min or higher (6050 Wide Format) A0 size: 3 sheets/min or higher (6030 Wide Format) Maximum: 15 m/49.2’ (at 100% scaling) Auto paper feed from roll Manual media feed (option) Chapter 9 Specifications...
  • Page 307 No power is consumed in the output section and printer when the circuit breaker is OFF even if the power plug is connected to the power source. * Maximum length will differ based on the amount of memory installed. 9.4 Machine Specifications (6030/6050) Specification Maximum width: 914 mm/36"...
  • Page 308 Xerox 6030/6050 Wide Format Amount of memory installed 512 Mbyte 1024 Mbyte A0 size A1 size A2 size 7.5 m 7.5 m 15 m 15 m A3 size Chapter 9 Specifications...
  • Page 309: Machine Specifications (6050A)

    Less than 19 seconds (with Architectural D size) 999 sheets maximum A0 size: 5 sheets/min or higher (6050 Wide Format) A0 size: 3 sheets/min or higher (6030 Wide Format) Maximum: 15 m/650’ (at 100% scaling) Auto paper feed from roll Manual media feed (option)
  • Page 310 Item Media Dimensions Weight Maximum power consumption Power consumption when main power switch is OFF Heat dissipation No power is consumed in the output section and printer when the circuit breaker is OFF even if the power plug is connected to the power source. Specification Maximum width: 914 mm/36"...
  • Page 311 Appendixes...
  • Page 312 Appendix 1 Connector Specifications RS-232C pin assignment (6030/6050 only) PIN No. Host side Straight cable [-] indicates no wiring. Both sides are male pins. Centronics pin assignment Printer Side (36-pin Amphenol half-pitch type) Terminal Signal name Busy Select nAck nFault...
  • Page 313 Host Side (36-pin Amphenol type) Terminal Terminal Signal name nStrobe Data 1 Data 2 Data 3 Data 4 Data 5 Data 6 Data 7 Data 8 nAck Busy Perror Select nAutoFd Logiv GND Chassis GND Peripheral Logic High Host Side (25-pin D-subconnector type) Terminal Terminal Signal name...
  • Page 314: Command List

    Appendix 2 HP-GL/HP-GL2 Command List This section explains the HP-GL and HP-GL/2 command support status that are unique to the 6030/6050 Wide Format. Command fully supported. Activates different actims from other ordinary commands. (Meaning in [ ]) Command not supported and ignored.
  • Page 315 X and Y coordinates. Cuts paper. Draws a polygon registered in the polygon buffer. Draws a square determined by the current pen position and relative coordinates from the point. Appendix 2 HP-GL/HP-GL2 Command List (6030/6050) 6030/6050 HP-GL HP-GL/2 Wide Format...
  • Page 316 Controls the pixel color when two or more graphics intersect. Displays a message on the control panel of the printer. Indicates the type of paper loaded on the printer. HP-GL 7 to +6) for line plotting. – 6030/6050 HP-GL/2 Wide Format Appendixes...
  • Page 317 Outputs the current position instructed by the last command and the pen up-down information. [6030/6050 Wide Format: Always returns the standard value (0,0,0)] Outputs read coordinates. [Always returns the standard value (0,0,0)] Outputs an error number.
  • Page 318 Specifies the character size by absolute values. Specifies the slant for the characters. Draws a specified character after moving the pen. Specifies a pen type. Specifies the character size by relative values. 6030/6050 HP-GL HP-GL/2 Wide Format y* (HP-GL) y (HP-GL/2)
  • Page 319 Defines and fills in a sector polygon. Specifies whether to express the pen width in millimeters or by percentage of the P1/P2 distance. Draws ticks on the X axis. Draws ticks on the Y axis. Appendix 2 HP-GL/HP-GL2 Command List (6030/6050) 6030/6050 HP-GL HP-GL/2 Wide Format...
  • Page 320 Appendix 3 HP-RTL Command List (6030/ 6050) Command name Command Enter HPGL/2 Mode ESC % # B Enter PCL Mode ESC % # A Reset ESC E Universal Exit ESC % #x|X Language/Start of Apple Talk Config ESC & B #...
  • Page 321 Move CAP Vertical ESC * p # y|Y Y Offset ESC * b # y|Y Appendix 3 HP-RTL Command List (6030/6050) Command Meaning and function Defines the blue color configuration of the color palette. Assigns a defined RGB parameter to an index number.
  • Page 322 Command name Command Destination Raster ESC * t # h|H Width Destination Raster ESC * t # v|V Height Raster Line Path ESC * b # l/L Negative Motion ESC & a # n|N Set Graphics ESC * t # r|R Resolution Simele Color ESC * r # U...
  • Page 323 Appendix 4 TIFF Tag List (6030/6050) Tag ID 00FE NewSubfileType Bit 0: Low Resolution Image Bit 1: Multi-Page Image Bit 2: Transparency Mask 00FF SubfileType 1: Full Resolution Image 2: Reduced-Resolution Image 3: Multi-Page Image 0100 ImageWidth 0101 ImageLength 0102...
  • Page 324 3: RGB 4: CMYK 0116 RowsPerStrip 0117 StripByteCounts 0118 MinSampleValue 0119 MaxSampleValue 011A XResolution 011B YResolution 011C PlanarConfiguration 1: Chunky Format (RGBRGB) 2: Planar Format (RRGGBB) Tag Name Revision 6030/6050 Wide Format y (Black/ white binary value only) Appendixes...
  • Page 325 2: Inch 3: Centimeter 0129 PageNumber 012D TransferFunction 0131 SoftWare 0132 DateTime 013C HostComputer 013E Predictor 013D WhitePoint 013F PrimaryChromaticties 0140 ColorMap 0141 HalftoneHints 0142 TileWidth 0143 TileLength Appendix 4 TIFF Tag List (6030/6050) Tag Name Revision 6030/6050 Wide Format...
  • Page 326 0156 TransferRange 0200 JPEGProc 1: Baseline sequential 14: Lossless 0201 JPEGInterchangeFormat 0202 JPEGInterchangeFormatLngth 0203 JPEGRestartInterval 0205 JPEGLossLessPredictors 0206 JPEGPointTransforms 0207 JPEGQTables 0208 JPEGDCTables 0209 JPEGACTables 0211 YCbCrCoefficients 0212 YCbCrSubSampling 0213 YCbCrPositioning 0214 ReferenceBlackWhite Tag Name Revision 6030/6050 Wide Format Appendixes...
  • Page 327 Tag ID Revision 6030/6050 Tag Name Wide Format 8298 33432 Copyright Appendix 4 TIFF Tag List (6030/6050)
  • Page 328 Appendixes...
  • Page 329 Symbols "1.1 Outline of Xerox 6030/6050 Wide Format Print Service" 41, 146 90-degree rotation administrator top page Alignment mark printing area mode AUTO (Input Option) AUTO (output option) auto layouts auto mapping Auto R/E auto roll auto scale auto-layout automatic mapping...
  • Page 330 EOP command Error Log error log 136, 137 error message film 224, 231 FTP command help image fragmentation function input image size input media series Input Option 33, 267, 273 interface IOT status IP command IPQ command 224, 240 IPR command IPRM command 47, 176, 208 job log...
  • Page 331 media size media tray (optional) media tray (standard) 121, 166 media type (Menu) button 188, 213, 214 meter display method of cutting paper 41, 146 mirror image MIX (output option) MIX2 (output option) MSI & manual paper feed unit offline mode 47, 212 offline plot 41, 127...
  • Page 332 42, 212 reprinting resolution 139, 168 roll media RS232C serial (Set) button 148, 151, 156 sets joint processing for lines 148, 151, 156, 160, 161 sets the end of the line setup screen shaft 40, 117, 169 size mapping size recognition priority mode 123, 139 size specification sleep mode...

This manual is also suitable for:

60506050a