Setting A Media; Setting Feeding And Take-Up Unit - MIMAKI tx300p Operation Manual

Color inkjet printer
Table of Contents

Advertisement

Chapter 2 Basic Operation

Setting a Media

This machine can be used with a roll media and leaf
media.
For usable medias, refer to P.1-14 "Usable sizes of
media".
• Take care not to drop the media on your foot when
setting the media.It may cause an injury due to the
media.
• When setting a roll media, work by two or more
people. Otherwise, you may hurt your back by the
weight of the roll media.
• Adjust the head height prior to setting the media.If
the head height is adjusted after the media is set,
this may cause a media jamming, deterioration of
the print quality or head damage.
• With this machine, you can set media on the right
side or in the center. When setting media, be sure
to set it so that it covers one of the two media
sensors on the back of this machine.
• If setting the media in the center, use the take-up
extension cable.
• The head height is adjustable according to the
purpose of use.

Setting Feeding and Take-up unit

For the "Feeding and Take-up unit" settings, set the
following items:
• Use feeding unit and take-up unit/ Do not use feeding unit or
take-up unit.
• Use/Do not use tension bar.
• Operation when the ON/OFF switch for feeding/ take-up unit
is pressed.
In this machine, by selecting how to use the tension bar in
the feeding/take-up unit setting, you can print by any of
the following four methods.
Tension bar
Use feeding and
Set the media refer to P.2-8.
take-up tension bar
Use on the feeding
In P.2-8 "Using the tension bar to set
side only
the roll media", configure the settings
by excluding all the operations for the
Use on the take-up
tension bar on the unused side.
side only
Do not use tension
Set the media refer to P.2-13.
bar
Press
1
in LOCAL.
• MACHINE SETUP MENU will be displayed.
Press
2
UP UNIT", and pressthe
Press the
3
• "FEEDING UNIT" will be selected.
Press
4
press the
• Set Value : ON/ OFF
2-4
How to set the media
(MENU)
(twice)
to select "FEEDING/TAKE-
key.
key.
to select a set value, and
key.
Press
, and press teh
5
• "FEEDING TENSION BAR" will be selected.
Press
to select a set value, and
6
pressthe
• Set Value : ON/ OFF
Press
, and pressthe
7
• "TAKE-UP UNIT" will be selected.
Press
to select a set value, and
8
press the
• Set Value : ON/ OFF
Press
, and press the
9
• "TAKE-UP TENSION BAR" will be selected.
Press
to select a set value, and
10
press the
• Set Value : ON/ OFF
Press
, and press the
11
• "Feeding/ Take-up SW" will be selected.
Press
to select a set value, and
12
press the
• Set Value : Continuance/ Temporary
Continuance :
Switching ON / OFF the winding operation when
pressing the switch each time. (Take-up unit in
operation does not stop until press again ON /
OFF switch.)
Temporary :
Do the winding operation only while holding
down the switch. (When release the switch,
winding operation is stopped. )
• If you are using the direct-connection unit, the
winding operation will be carried out with the
"TEMPORARY" setting even if you select
"CONTINUANCE".
Press the
13
end the setting.
• Set feeding/take-up tension bar in "FEEDING/
TAKE-UP" before setting media. Even if you try
after detecting the media width (
cannot set feeding/take-up tension bar.
• You can change the ON/OFF settings of Feeding/
Take-up unit after detecting the media width.
When turning OFF from ON
Feeding/take-up unit does not operate.
When turning ON from OFF
If torque limiter is attached, only take-up
operation without using tension bar is
performed.
If direct-connection unit is attached, take-up
operation is not performed.
• If you want to change the feeding/ take-up method
while setting media, remove the set media and
carry out the operations from step 1 again.
key.
key.
key.
key.
key.
key.
key.
key.
key several times to
P.2-11), you

Advertisement

Table of Contents
loading

Table of Contents