Download Print this page

Advertisement

4020024 Rev B
Encoder Model D9040
User and Service Manual
Software Version 1.0

Advertisement

   Related Manuals for Cisco D9040

   Summary of Contents for Cisco D9040

  • Page 1

    4020024 Rev B Encoder Model D9040 User and Service Manual Software Version 1.0...

  • Page 3

    Copyright © 2007-2011, 2012 Cisco and/or its affiliates. All rights reserved. Printed in the United States of America. Information in this publication is subject to change without notice. No part of this...

  • Page 4

    THIS PRODUCT IS LICENSED UNDER THE AVC PATENT PORTFOLIO LICENSE FOR THE PERSONAL AND NON-COMMERCIAL USE OF A CONSUMER TO (i) ENCODE VIDEO IN COMPLIANCE WITH THE AVC STANDARD ("AVC VIDEO") AND/OR (ii) DECODE AVC VIDEO THAT WAS ENCODED BY A CONSUMER ENGAGED IN A PERSONAL AND NON-COMMERCIAL ACTIVITY AND/OR WAS OBTAINED FROM A VIDEO PROVIDER LICENSED TO PROVIDE AVC VIDEO.

  • Page 5

    Please Read This Entire Guide Veuillez lire entièrement ce guide Bitte das gesamte Handbuch durchlesen Sírvase leer completamente la presente guía Si prega di leggere completamente questa guida Important: Please read this entire guide before you install or operate this product. Give particular attention to all safety statements.

  • Page 7: Safety Precautions

    Safety Precautions Protect yourself from electric shock and your system from damage! • This product complies with international safety and design standards. Observe all safety procedures that appear throughout this guide, and the safety symbols that are affixed to this product. •...

  • Page 8: Règles De Sécurité

    Règles de sécurité Protégez-vous des risques d'électrocution et protégez votre système contre les endommagements éventuels. • Ce produit respecte les standards internationaux de sécurité et de conception. Veuillez observer toutes les procédures de sécurité qui apparaissent dans ce guide, ainsi que les symboles de sécurité...

  • Page 9: Sicherheitsvorkehrungen

    Sicherheitsvorkehrungen Schützen Sie sich gegen elektrischen Schlag, und Ihr Gerät gegen Beschädigung! • Dieses Gerät entspricht internationalen Sicherheits-und Ausführungsnormen. Beachten Sie alle in diesem Handbuch enthaltenen Sicherheitshinweise sowie die am Gerät angebrachten Warnzeichen. • Sollten örtliche Umstände den sicheren Betrieb dieses Gerätes beeinträchtigen, schalten Sie es ab und sichern es gegen weitere Benutzung.

  • Page 10: Precauciones De Seguridad

    Precauciones de seguridad ¡Protéjase contra la electrocución y proteja su sistema contra los daños! • Este producto cumple con los criterios internacionales de seguridad y diseño. Observe todas los procedimientos de seguridad que aparecen en esta guía, y los símbolos de seguridad adheridos a este producto.

  • Page 11: Precauzioni Di Sicurezza

    Precauzioni di sicurezza Proteggetevi da scosse elettriche e proteggete il vostro sistema da possibili danni! • Questo prodotto soddisfa le norme internazionali per la sicurezza ed il design. Seguite tutte le procedure di sicurezza contenute in questa guida e i simboli di sicurezza applicati al prodotto.

  • Page 12: Important Safety Instructions

    Important Safety Instructions Read and Retain Instructions Carefully read all safety and operating instructions before operating this equipment, and retain them for future reference. Follow Instructions and Heed Warnings Follow all operating and use instructions. Pay attention to all warnings and cautions in the operating instructions, as well as those that are affixed to this equipment.

  • Page 13

    Important Safety Instructions, Continued Installation Site When selecting the installation site, comply with the following: • Protective Ground - The protective ground lead of the building's electrical installation should comply with national and local requirements. • Environmental Condition - The installation site should be dry, clean, and ventilated. Do not use this equipment where it could be at risk of contact with water.

  • Page 14

    Important Safety Instructions, Continued Rack Mounting Safety Precautions Mechanical Loading Make sure that the rack is placed on a stable surface. If the rack has stabilizing devices, install these stabilizing devices before mounting any equipment in the rack. WARNING: Avoid personal injury and damage to this equipment. Mounting this equipment in the rack should be such that a hazardous condition is not caused due to uneven mechanical loading.

  • Page 15

    Depending on the type and application of this equipment (Safety Class I or Safety Class II), Cisco supplies a mains cord with either a 3-terminal (grounding-type) safety plug or a 2-terminal (polarized) safety plug. The wide blade or the third terminal is provided for safety.

  • Page 16

    Important Safety Instructions, Continued AC Power Important: If this equipment is a Class I equipment, it must be grounded. • If this equipment plugs into an outlet, the outlet must be near this equipment, and must be easily accessible. • Connect this equipment only to the power sources that are identified on the equipment- rating label normally located close to the power inlet connector(s).

  • Page 17

    The batteries may contain substances that could be harmful to the environment. • Replace batteries with the same or equivalent type recommended by Cisco. • Insert batteries correctly. There may be a risk of explosion if the batteries are incorrectly inserted.

  • Page 18

    Important Safety Instructions, Continued Where this equipment is subject to USA FCC and/or Industry Canada rules, the following statements apply: FCC Statement This equipment has been tested and found to comply with the limits for a Class A digital device according to Part 15 of FCC Rules. These limits are designed to provide reasonable protection against harmful interference when this equipment is operated in a commercial environment.

  • Page 19: Compliance

    Compliance Electromagnetic Compatibility FCC Part 15 Subpart B: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. CE marked: according to EMC directive 89/336/EEC and 93/68/EEC (European standards EN 55 022, EN 55 024, EN 61000-3-2 and EN 61000-3-3).

  • Page 20: Warranty And Disclaimer

    Warranty and Disclaimer The terms "we", "us", and "our" are used to refer to Cisco Systems, Inc. The term "Item" is used to refer to our products (including software) provided hereunder. We make no representations that our product is fully compatible with similarly represented equipment from other vendors due to the wide range of implementation possibilities of the applicable standards.

  • Page 21

    Warranty and Disclaimer, Continued THIS WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESS, IMPLIED OR STATUTORY, INCLUDING ANY WARRANTY OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE OR NONINFRINGEMENT. PURCHASER'S SOLE REMEDY FOR ANY BREACH OF WARRANTY FOR HARDWARE ITEMS MANUFACTURED BY OR FOR US AND SOFTWARE ITEMS LICENSED BY US IS THE REPAIR OR REPLACEMENT, AT OUR OPTION, OF THE FAILED ITEM.

  • Page 22

    4020024 Rev C xviii...

  • Page 23: Table Of Contents

    Chapter 3 Installation Overview..........................3-1 Section A - Rack Installation ....................3-2 General..........................3-2 Installing the D9040 Encoder ..................3-3 Section B - Connector Panel....................3-5 Overview ..........................3-5 Section C - Connecting the Input/Output Signals ..............3-7 Connecting the Video and Reference Signal Inputs ............3-7 Connecting the Audio Inputs..................3-8...

  • Page 24

    Connecting to the Contact Closure or Cue Tone Interfaces........3-12 Connecting the Statmux Interface ................3-13 Connecting an External Alarm System................3-14 Connecting the Ethernet Management Interface............3-15 Connecting the ASI Outputs and the ASI Monitor Decoder ........3-16 Chapter 4 Front Panel Operation Overview..........................4-1 About the Front Panel ......................4-2 Keypad Convention......................4-4 Startup Screen........................4-5...

  • Page 25

    Section E - Control and Management Interfaces..............A-18 Section F - Power and General Specifications ..............A-20 Power ..........................A-20 Appendix B Equipment and Accessories Overview........................... B-1 Accessory Kits for the D9040 Encoder ................B-2 Options and Accessories ....................B-3 Appendix C References Applicable Documents ....................C-1 Glossary ............................

  • Page 26

    4020024 Rev C xxii...

  • Page 27: About This Manual

    About This Manual Objective This manual describes how to install, use and maintain the Encoder Model D9040. Note: The manual describes all available options for the D9040 Encoder. Your D9040 Encoder may only have some of the features described in this manual.

  • Page 28

    4020024 Rev C xxiv...

  • Page 29: Chapter 1 Quick Setup - Read Me First

    For further information, see Connecting the Audio Inputs, page 3-8. 4. Connect the statmux interface connector of each of the D9040 Encoders to one of the 16 statmux channel connectors of the Regulus Controller.

  • Page 30

    11. Connect the power sources of all the units. For further information, see the specific product manuals in question. When connecting the power source to the D9040 Encoder it takes up to 120 seconds for the unit to initialize. The front panel display shows the startup display.

  • Page 31: Front Panel Setup

    PNC control system. Also do as follows when a D9040 Encoder is added to or reinserted in the installation. Proceed as follows to set the IP settings of the D9040 Encoder, and if necessary change them: 1.

  • Page 32

    4020024 Rev C Quick Setup - Read Me First!

  • Page 33: Chapter 2 Introduction

    Chapter 2 Introduction Overview Introduction This chapter is a general introduction to the Encoder Model D9040. It describes the most common applications and interfaces of the D9040 Encoder. In This Chapter This chapter contains the following topics. Topic See Page...

  • Page 34: Encoder Model D9040

    Encoder Model D9040 General Description The design of the Encoder Model D9040 is compact. The D9040 Encoder is a 1U encoder that fits into a 19-inch rack. It features single-channel High-Definition high-quality SDI and/or composite video processing. It is targeted at uplink...

  • Page 35

    Audio Channels The D9040 Encoder is equipped with an SDI input and two composite inputs. You may order the D9040 Encoder with either two or four stereo audio channels. The audio channels may be part of the video service. 4020024 Rev C...

  • Page 36

    525 Lines 625 Lines VITC VITC VITC VITC VITC NABTS Neilsen/ AMOL Gemstar Transparent Reference Input The D9040 Encoder provides a reference input for internal frame synchronization of the video input to an external studio reference. 4020024 Rev C Introduction...

  • Page 37

    It is possible to adjust the filter manually during operation without service interruption. The PreSightPlus video noise reduction and pre-analysis features are options that may be ordered with the D9040 Encoder or added later. Sub-sampling The D9040 Encoder supports subsambling. Sub-sampling decreases the resolution of the source material in order to lower the amount of data to be encoded.

  • Page 38: Application Example

    In addition to the PNC, a PowerVu system can also support a number of IRDs to meet specific customer needs. The Regulus™ Statistical Multiplex Controller is an add-on unit for the D9040 Encoder. You may connect the Regulus Controller to a number of encoders so that they together may participate in statistical multiplexing.

  • Page 39: Video Interfaces

    The SDI input interface accepts a 270 Mbit/s SDI formatted video input (D-1). The SDI module extracts embedded audio for further processing by an audio encoder module. VBI and Related Signals The D9040 Encoder supports teletext B, DVB-VBI Teletext, Transparent Lines, VPS, WSS, VII and Closed Captioning. Encoding The video encoding includes: •...

  • Page 40: Audio And Data Interfaces

    Audio and Data Interfaces Audio Input Four audio stereo channels can be input at the D9040 Encoder. Each of the audio channels can be sourced from analog, digital AES-3id or embedded SDI audio sources. You can assign the encoded audio channels to the video program or to independent audio only programs.

  • Page 41

    The D9040 Encoder supports passthrough of up to four pre-encoded AAC channels. Audio Only The D9040 Encoder supports up to eight mono or four stereo audio only programs. One or more audio sources can be combined to make up a program.

  • Page 42: Transport Stream Outputs

    Transport Stream Outputs DVB-ASI Transport Stream Output The D9040 Encoder has three DVB-ASI outputs. These outputs can be used as an input for a satellite modem or a multiplexer. One of the outputs is an ASI monitor output for monitoring of the outgoing data stream. Unlike the two other ASI outputs the monitor output cannot be muted.

  • Page 43: Control And Management Interfaces

    Numeric Keypad Ethernet The main control interface for the D9040 Encoder is the 10/100 BaseT Ethernet interface. You can set up and control the D9040 Encoder via the Ethernet connection using SNMP and the PNC control system. 4020024 Rev C Introduction...

  • Page 44

    Alarm connector on the rear panel of the D9040 Encoder. Furthermore, the alarm status is signalled by Alarm LEDs on the front of the D9040 Encoder and by messages sent via the PNC control system. Refer to Connecting an External Alarm System, page 3-14 for more information.

  • Page 45: Chapter 3 Installation

    Chapter 3 Installation Overview Introduction This chapter describes how to install the Encoder Model D9040. Before installing the D9040 Encoder, read all safety precautions and guidelines thoroughly. Qualified Personnel Only appropriately qualified and trained service personnel or operators should attempt to install, operate or maintain the D9040 Encoder.

  • Page 46: Section A - Rack Installation

    Section A - Rack Installation General Power Connection As Cisco units are designed for 24-hour operation, some products do not have a power switch. In this case, the mains cord serves as the mains disconnect device. WARNING: Make sure that at least one end of the power cables remains easily accessible for unplugging, if you need to switch off the unit.

  • Page 47: Installing The D9040 Encoder

    The D9040 Encoder is a 1U unit with connector access at the rear panel. The D9040 Encoder is intended for mounting in a standard 19" rack. Cooling The D9040 Encoder is cooled by the use of fans. The air intake is from the front panel and the air outlet is on the rear. CAUTION: The inlet air temperature must not exceed 50 °C/122 °F at any time.

  • Page 48

    To Connect AC Power To connect AC power to the D9040 Encoder do the following: 1. Connect the power cords(supplied with the D9040 Encoder) between the rear panel power receptacles and an 100 to 240 V AC power outlet. 2. Make sure that the power cables are connected to protective ground.

  • Page 49: Section B - Connector Panel

    Section B - Connector Panel Overview D9040 Encoder Connector Panel The following drawing shows the rear connector panel of the D9040 Encoder. Contact Analog Audio Reference Unused Closure ASI Monitor AC Power Management SDI In In, 1 + 2 Tone...

  • Page 50

    ALARM Alarm relays 9-pin sub-D female 10/100 BASE-T For control and management of local RJ45 MANAGEMENT and remote D9040 Encoder units. STATMUX Connection to the Regulus Statistical 9-pin sub-D female Multiplex Controller ETHERNET 100 Transport stream encapsulated in IP RJ45 BASE-T AUX packets.

  • Page 51: Section C - Connecting The Input/output Signals

    Section C - Connecting the Input/Output Signals Connecting the Video and Reference Signal Inputs Connectors for the Video and Reference Signal Inputs Both the SDI, composite video input and reference input connectors are of the BNC type and are internally terminated. The following video and reference input signals are supported: •...

  • Page 52: Connecting The Audio Inputs

    3 and 4 is input at the bottom row of pins on the terminal block connector. On the PNC, you can set up the D9040 Encoder to use either the analog or the digital stereo channels. The D9040 Encoder also supports encoding of audio embedded in the SDI video signal.

  • Page 53

    Connecting the Audio Inputs, Continued The pinout for the analog part of the terminal block connector is as follows: Channel Analog Numbering Layer Dolby Type Signal Number Digital Analog Left + Left - Shield Analog Right + Right - Shield Analog Left + Left -...

  • Page 54

    Connecting the Audio Inputs, Continued The pinout for the digital part of the terminal block connector is as follows: Channel AES/EBU AES-3id Numbering Layer Dolby Type Signal Type Signal Number Digital 1 to 12 5 & 6 Digital Digital In Signal Ground Shield Shield...

  • Page 55

    AES/EBU digital audio or a coaxial cable designed for 75-ohm AES-3id. Use a high-quality balanced audio cable for the analog inputs. If you have many or heavy audio cables connected to the D9040 Encoder, you may need to suspend the cables in your rack to prevent unnecessary mechanical stress on the audio connector.

  • Page 56: Connecting To The Contact Closure Or Cue Tone Interfaces

    Connecting to the Contact Closure or Cue Tone Interfaces Contact Closure and Cue Tone Connector The D9040 Encoder has a contact closure and a cue tone interface (not used), which can be used to trigger digital program insertion (DPI). The contact closure interface has 8 inputs.

  • Page 57: Connecting The Statmux Interface

    Connecting the Statmux Interface Connector for the Statmux Input The D9040 Encoder has one bidirectional RS-232 data channel for connection to the Regulus Statistical Multiplex Controller. The following table shows the female Statmux connector and the pin allocation for the RS-232 input.

  • Page 58: Connecting An External Alarm System

    A-alarm is active and the A-alarm LED lights on the front panel. Note: The A-alarm relay is always activated when the power is off or the D9040 Encoder is booting, whereas the other alarm relays maintain their status.

  • Page 59: Connecting The Ethernet Management Interface

    D9040 Encoder directly to another Ethernet device without using a hub or switch. You need to set up the IP address on both the D9040 Encoder (via the front panel display). For information on setting up the IP address via the front panel, see Front Panel Setup, page 1-3.

  • Page 60: Connecting The Asi Outputs And The Asi Monitor Decoder

    To Connect the ASI Outputs Do as follows to connect to the ASI output: 1. Connect the output signals from the D9040 Encoder connectors ASI OUT 1 and/ or ASI OUT2 to the ASI input connectors of the equipment after the D9040 Encoder.

  • Page 61: Chapter 4 Front Panel Operation

    Chapter 4 Front Panel Operation Overview Introduction This chapter describes how to set up the D9040 Encoder using the front panel keys and display. In This Chapter This chapter contains the following topics. Topic See Page About the Front Panel...

  • Page 62: About The Front Panel

    About the Front Panel Introduction The D9040 Encoder is operated using controls and indicators on the front panel. These include the numeric keypad, the Navigation/Selection keypad, the LCD, the ALARM and POWER indicators. These are shown in the following illustration:...

  • Page 63

    About the Front Panel, Continued Navigation/Selection Keypad The navigation keys (LEFT, RIGHT, UP and DOWN) and the SELECT key on this keypad are the primary controllers. Each navigation key performs various functions, depending on the current state of the menu system (i.e. sometimes the left navigation key backspaces over an entry and sometimes moves the cursor to a different menu item).

  • Page 64: Keypad Convention

    Keypad Convention Overview Throughout this manual, there are references to parts of a keypad on the front of the encoder. This is the Navigation/Selection keypad (see diagram at right), which changes its function, depending on the current state of the menu. For clarity, the following table shows which parts of this integral interface are being referenced by which term.

  • Page 65: Startup Screen

    It is used for uniquely identifying the D9040 Encoder. IP Addr. Description: The IP address of the D9040 Encoder. The IP address is set up from the System menu, see IP, Management, IP Address, page 4-7. 4020024 Rev C...

  • Page 66: Main Menu

    Main Menu Structure Operation of the Encoder Model D9040 begins at the Main menu. From the startup screen press the MENU or SELECT key to view the Main menu. Main Menu System Lock Menu Selection Select the desired function by moving the cursor left or right by pressing the LEFT or RIGHT key.

  • Page 67: System Menu

    Any inconsistencies will be shown in the display. Important: For the changes to take effect, you must reset the D9040 Encoder after you have finished setting or changing the IP address, subnet mask and default gateway. The D9040 Encoder will display a reminder.

  • Page 68

    <0 to 255>.<0 to 255>.<0 to 255>.<0 to 255> Description: The default gateway of the management interface to D9040 Encoder. The D9040 Encoder uses this gateway to route IP traffic across the network. Setup similar to IP, Management, IP Address, page 4-7, above.

  • Page 69

    System Menu, Continued Option License, PNC Management Parameters: Enabled, Disabled Description: The status of the license signifies the following: Status Explanation Enabled The option is present and enabled. Disabled The option is either disabled or uninstalled. In this case you have to enable or install the option to make it work.

  • Page 70

    Disabled The option is either disabled or uninstalled. In this case you have to enable or install the option to make it work. Please contact your local Cisco sales representative if you want to buy an option. 4020024 Rev C...

  • Page 71

    The option is either disabled or uninstalled. In this case you have to enable or install the option to make it work. Please contact your local Cisco sales representative if you want to buy an option. Option License, VBI Parameters:...

  • Page 72

    • you have set or changed the IP address, subnet mask or gateway of one of the IP interfaces of the D9040 Encoder via the front panel display. Note: The reset may take up to 120 seconds.

  • Page 73

    UP or PREV to leave the menu without making any changes. Use the default settings if you have set up the D9040 Encoder with illegal and incompatible settings to get the encoder back in a functional state.

  • Page 74: Lock Menu

    Lock Menu Structure To see the Lock menu from the Main menu press the RIGHT Arrow key five times and the SELECT key. Each parameter is described in the following. For instructions on how to select and store settings, see About the Front Panel, page 4-2. The menu has the following structure: Lock Unlocked...

  • Page 75: Chapter 5 Service And Maintenance

    Overview Introduction This chapter gives information to assist you in replacing the fan and fuses. It also describes how the status of the D9040 Encoder is communicated via front panel LEDs and messages. In This Chapter This chapter contains the following topics.

  • Page 76: Section A - Replacing Fans And Fuses

    Adjustment and Calibration The D9040 Encoder does not require regular adjustments or calibrations, however to ensure proper cooling it is recommended that the fan be replaced every four years. In addition the fan can be replaced if the installed fan is not functioning correctly.

  • Page 77: Replacing The Fan

    Replacing the Fan General To ensure proper cooling of the D9040 Encoder replace the fan every fourth year. WARNING: Allow only qualified service personnel to open the unit. Otherwise, personal injury or equipment damage may occur. Before You Start You need the following tools and accessory:...

  • Page 78

    Replacing the Fan, Continued 3. Unscrew and remove the nuts and washers. Two in front of the fan unit, and one at each side. Use an internal hex 5 mm screwdriver. 4. Unplug the fan connector at the main board. 4020024 Rev C Service and Maintenance...

  • Page 79

    Replacing the Fan, Continued 5. Unplug the front panel connector from the main board. 6. Pull out the cable through the opening in the fan unit. 7. Replace the fan. 8. Mount in reverse order. Important: Make sure that the cable with the front panel connector goes through the opening in the fan unit and not below it.

  • Page 80: Replacing An Ac Fuse In The Power Supply

    98-017 5. Remove the blown fuse(s). 6. Insert a new fuse with the same rating. The fuse rating for the D9040 Encoder is 2 AT. CAUTION: For continued protection against risk of fire replace only with same type and rating of fuse.

  • Page 81: Section B - Status Signaling

    Front Panel LEDs Overview To help signal the status of operation or the presence of an alarm the D9040 Encoder makes use of front panel LEDs. The drawing below shows the LEDs on the front panel of the D9040 Encoder.

  • Page 82: Messages

    Messages General The status of the D9040 Encoder and its immediate surroundings is reported to the PNC in the form of messages and alarms. In the PNC, you can enable or disable messages and attach an alarm category to each message.

  • Page 83

    Description: The installed license file Information None option as it is not doesn’t contain information about the installed. enabled license. Remedy: Order the needed license through your local Cisco technical support center. Clock Description: The device failed to fetch the Warning None synchronization clock from the time server.

  • Page 84

    Message Description and Remedy Severity Default Enable alarm category Dolby Digital: Description: The audio delay setup on the Minor None DSP Delay high Audio DSP is too high. Remedy: Decrease error. the audio delay. Dolby Digital: Description: The audio delay setup on the Major DSP Delay low Audio DSP is too low.

  • Page 85

    The encoding will restart. Remedy: Check the settings. Change the audio encoding rate or increase the TS rate. If a FIFO error occurs recurrently, contact your Cisco technical support center. DPI Cancel Description: An external control signal...

  • Page 86

    The encoding will restart. Remedy: Check your settings for parameter violations. Observe the limitations in the manual. If persistent, contact your Cisco technical support center for further assistance. Fan malfunction. Description: The system has detected a Critical fan malfunction.

  • Page 87

    The encoding will restart. Remedy: Check the settings. Change the audio encoding rate or increase the TS rate. If a FIFO error occurs recurrently, contact your Cisco technical support center. 4020024 Rev C Service and Maintenance...

  • Page 88

    Power supply Description: Power supply defective or Major failure. external power line broken Remedy: Check power cable. If persistent, contact your Cisco technical support center for repair. Power-up self- Description: The internal power-up self- Critical test failed. test failed. Remedy: When persistent, contact your Cisco technical support center for further assistance.

  • Page 89

    Message Description and Remedy Severity Default Enable alarm category Subcarrier Description: The input is not able to lock Major unlock. to the subcarrier. Remedy: The frequency offset is likely too high. Color reproduction may suffer. Check your video source. Sync unstable. Description: The composite video Major synchronization signal is unstable.

  • Page 90

    TS rate. In a statmux set-up, the TS rate of an encoder must have room for the maximum instantaneous encoding rate. If a FIFO error occurs recurrently, contact your Cisco technical support center. VII error. Description: The encoder has detected an Major None error in the VII signal.

  • Page 91: Chapter 6 Customer Information

    Chapter 6 Customer Information If You Have Questions If you have technical questions, call Cisco Services for assistance. Follow the menu options to speak with a service engineer. Access your company's extranet site to view or order additional technical publications. For accessing instructions, contact the representative who handles your account.

  • Page 93: Appendix A Technical Specifications

    Appendix A Technical Specifications Overview Introduction This appendix contains the technical specifications for the Encoder Model D9040. Note: The technical specifications are subject to change without prior notice. In This Appendix This appendix contains the following topics. Topic See Page...

  • Page 94: Section A - Video Input And Processing

    Section A - Video Input and Processing MPEG-2 Encoder Specifications General Item Specification Number of channels Encoding engine According to MPEG-2, MP@ML Frame types I, P, and B frames Encoding control Adaptive coding parameters and GOP controlled by pre-analysis PreSightPlus pre-analysis Look-ahead for improved statistical multiplexing and normal fixed rate encoding.

  • Page 95: Composite Video Input

    Composite Video Input Video Formats Item Specification Composite video PAL systems B, D, G, H, I, K, M, N and NTSC system M, and J-NTSC acc. to BT 470-6 Input Characteristics Item Specification Number of inputs Type of connector BNC female Nominal internal termination, 75 ohm impedance...

  • Page 96

    Composite Video Input, Continued Frame Synchronizer Item Specification Frame locking To an internal nominal 27 MHz reference or an external reference via the analog REF IN connector Tolerance of the internal reference 10 ppm Audio wandering upon frame skip/ ± 1 frame repeat (when frame synchronizer is enabled) VBI behavior upon frame skip/...

  • Page 97

    Composite Video Input, Continued Composite Video Performance Item Specification, Advanced Specification, Onboard Video Input Module Composite module Gain Insertion gain ± 0.2 dB Level stability ± 0.10 dB / 1 hour ± 0.15 dB/ 24 hour Noise Quantization Noise, unified ≤...

  • Page 98: Vbi Specifications In Composite Video

    VBI Specifications in Composite Video VBI Processing Item Specification Teletext B General Teletext B acc. to ITU-R BT.653-3 Lines in 625 lines systems 7 to 22, 320 to 335, maximum 16 lines per field for DVB Inverted Teletext Applicable for EBU and DVB teletext Output formats According to EN 301 775 V1.1.1 (DVB-VBI Teletext) and/or...

  • Page 99: Vbi Specifications In Composite Video

    VBI Specifications in Composite Video, Continued DVB Compliant Transparent VBI Item Specification Lines in 625/50 7 to 23, 319 to 335 Lines in 525/60 10 to 22 field 1 and 10 to 22 field 2 (273 to 284) ≤ 2 VBI lines per field are transferred Number of lines transparently if no other DVB VBI is present.

  • Page 100: Sdi Input

    SDI Input System Item Specification Video Formats Signal form Y, CR, CB Sampling structure 4:2:2 Line numbers/field rates 525/29.97 Hz, 625/25 Hz Bit rate 270 Mbit/s ± 10 ppm Video data word size 8 bit and 10 bit Input Characteristics Item Specification Number of inputs...

  • Page 101: Embedded Data In Sdi

    Embedded Data in SDI VBI Processing Item Specification General According to SMPTE RP 165. Alarms Gives an error message if there is a checksum error in the EDH or no EDH on the incoming SDI signal. Teletext B General Teletext B acc. to ITU-R BT.653-3 Lines system 625 lines SDI Lines in 625 lines systems...

  • Page 102

    Embedded Data in SDI, Continued DVB Compliant Transparent VBI General Acc. to ETS 300 294 (ETSI) or Vistek Data Sheet 1649 (AFD) Lines in 625 lines systems First half of line 23 Output format According to EN 301 775 V1.1.1. VITC General According to ISO13818-2...

  • Page 103

    Embedded Data in SDI, Continued Embedded Audio Item Specification Location of audio The encoder accepts audio transmitted in any ancillary data space. Formatting According to SMPTE 272M Audio sampling frequency 48 kHz locked to the video. According to SMPTE 272M Resolution 20 bits Number of channels...

  • Page 104: Section B - Audio Input And Processing

    Section B - Audio Input and Processing Audio Input General Item Specification Inputs Analog, Digital AES/EBU or AES-3id and embedded. AES/EBU is not supported for channels 1 and 2. Connectors Digital Audio In, Ch. 1 + 2 2 BNC connectors Analog Audio In, Ch.

  • Page 105

    Audio Input, Continued AES-3id Digital Audio Input, Channels 1 and 2 in BNC and 3 and 4 in Terminal Block Item Specification Encoding According to SMPTE 276M Input impedance 75 ohm single-ended ≥ 15 dB, 0.1 to 6.0 MHz Return loss Input level 0.5 to 2 Vpp nominal AES-3id Reference Output, Channels 3 and 4 in Terminal Block Connector...

  • Page 106: Audio Processing

    Audio Processing Audio Performance Item Specification Insertion gain ±0.5 dB Pass-band frequency response ±0.25 dB, rel. 1 kHz 32 kHz sample rate 20 to 14,500 Hz 44.1 and 48 kHz sample rate 20 to 20,000 Hz Crosstalk < -80 dB, 20 Hz to 20 kHz Gain difference between channels ±0.5 dB, 20 Hz to 20 kHz Phase difference between channels...

  • Page 107

    Audio Processing, Continued Dolby Digital Encoding Item Specification Encoding According to ATSC Standard: Digital Audio Compression (AC-3) Rev. A, August 2001. Audio Coding Modes Dual Mono 1+1, Mono 1/0, Stereo 2/0 Audio data rate 56, 64, 80, 96, 112, 128, 160, 192, 224, 256, 320, 384, 448, 512, 576 and 640 kbit/s Sample frequency 32, 44.1 and 48 kHz...

  • Page 108: Section C - Data Interfaces

    Section C - Data Interfaces Statmux Interface Item Specification Number of inputs Type of connector 9-pin sub-D female (DCE) Type of input Bi-directional, asynchronous RS-232-E Baud rates as data interface 38400 Data format 8N1, no parity 4020024 Rev C A-16 Technical Specifications...

  • Page 109: Section D - Transport Stream Output

    Section D - Transport Stream Output ASI Output Item Specification Number of outputs 3, one is designated ASI Monitor Type of connector 75 ohm BNC Output impedance 75 ohm according to EN 50083-9 Data amplitude 800 mV peak-peak ± 10% according to EN 50083-9 Return loss >15 dB, 27 to 270 MHz...

  • Page 110: Section E - Control And Management Interfaces

    Section E - Control and Management Interfaces Ethernet Management Interface Item Specification Number of connectors Type of connector Eight-pin RJ-45, MDI Ethernet type 10/100 Base-T Required setup IP address, default gateway and subnet mask Alarm Interface Item Specification Number of outputs 3, each having one set of contacts closed and one set open during normal operation.

  • Page 111

    Control and Management Interfaces, Continued Front Panel Interface Item Specification 2 lines of 40 characters backlit LCD. Keypad Arrow keys, 0 to 9, Select, Menu Prevand F1 to F4 keys. LEDs Green LED for power on. Red LED for Alarm indication. 4020024 Rev C Technical Specifications A-19...

  • Page 112: Section F - Power And General Specifications

    ≤ 95 W fully equipped Input power consumption Input frequency 47 to 63 Hz Fuse 2.0 AT fuse in both line and neutral conductor Mechanics, D9040 Encoder Item Specification Sub-rack According to IEC 297-3 Height 1 U (44.5 mm) (1.75”) Width 482 mm (19”)

  • Page 113

    Power, Continued Environment Item Specification Storage/Transportation General The product is within the original packaging. Humidity 95% Relative Humidity at +50°C/122°F according to IEC 60068-2-78. Test: Cab Temperature -20 to +70°C (-4 to 158°F) Vibration, transportation According to MIL-STD-810E, Method 514.4, Category 1, Basic transportation Fall, transportation According to ETS 300 019 part 1-2.

  • Page 114

    4020024 Rev C A-22 Technical Specifications...

  • Page 115: Appendix B Equipment And Accessories

    This appendix contains names and part numbers of equipment and accessories for the D9040 Encoder. In This Appendix This appendix contains the following topics. Topic See Page Accessory Kits for the D9040 Encoder Options and Accessories 4020024 Rev C Equipment and Accessories...

  • Page 116: Accessory Kits For The D9040 Encoder

    Accessory Kits for the D9040 Encoder Accessory Kit, AC Version The accessory kit for the AC version of the D9040 Encoder is included in the delivery. It has the part number 4013357 and contains the following items: Part number Description...

  • Page 117: Options And Accessories

    Ready , US power cord 1. DPI for the D9040 Encoder in PNC systems requires a valid PNC DPI Option license. 2. “AVC Ready” indicates that the D9040 Encoder will ship with the necessary hardware to accommodate AVC encoding. AVC encoding requires 4018041.010. It will be available in the future as a software upgrade with an additional license option at a commercially reasonable price.

  • Page 118

    4013737 Audio Channels 3 and 4, uncludes MPEG-1 Layer II 1) Please contact your local Cisco sales representative if you want to buy an option. 2) Please contact your local Cisco sales representative if you want to buy an option.

  • Page 119

    Options and Accessories, Continued Optional Accessories, D9040 Encoder The following optional accessories are available. • Part Description To be used/Comment number 4013724 Fan kit The fan lifetime is at least 4 years at 45°C ambient temperature. 4013127 Kit, AC Power Supply Unit Spare part.

  • Page 120

    4020024 Rev C Equipment and Accessories...

  • Page 121: Appendix C References

    Appendix C References Applicable Documents AES3-1992 Serial transmission format for two-channel linearly represented digital audio data. ANSI/SMPTE 12M-1995 Television, Audio and Film ---- Time and Control Code AS/NZS, 2002 Limits and methods of measurements of radio disturbance characteristics of information technology equipment. ATSC Standard, Digital Audio Compression (AC-3) Rev.

  • Page 122

    Applicable Documents, Continued ETSI EN 300 468 Digital Video Broadcasting (DVB); Specification for Service Information V1.4.1, 2000-11 (SI) in DVB systems. ETSI TR 102 154 v1.1.1, Digital Video Broadcasting (DVB); Implementation guidelines for the 2001-04 use of MPEG-2 Systems, Video and Audio in Contribution and Primary Distribution Applications.

  • Page 123

    Applicable Documents, Continued ITU-R Rec. 647, 1986 A digital audio interface for broadcasting studios. RFC 791, 1981 Internet protocol, protocol specification. RFC 867, 1985 Daytime Protocol. RFC 1904, 1996 Conformance Statements for Version 2 of the Simple Network Management Protocol (SNMPv2). SMPTE 272M, 1994 Proposed edition, “Formatting AES/EBU Audio and Auxiliary Data into Digital Video Ancillary Data Space.”...

  • Page 124

    4020024 Rev C...

  • Page 125: Glossary

    Glossary List of Terms and Abbreviations AES/EBU Audio Engineering Society/European Broadcasting Union. AES/EBU is the name of a digital audio transfer standard. The AES and EBU developed the specifications for the standard. AES/EBU is an alternative to the AES-3id standard. Asynchronous Serial Interface.

  • Page 126: Index

    Index AC fuse data input 3-13 rating connector A-20 3-13 AES/EBU input data interfaces 3-13 AES-3id specification A-16 specifications digital audio A-13 alarm AES/EBU specifications A-12 connector AES-3id output specifications 3-14 A-14 interface connector 3-14 specifications specifications A-18 A-13 system connectors Dolby Digital 3-14 alarm relay...

  • Page 127

    Index, Continued PreSightPlus noise reduction ground specifications sub-sampling product support IP address setting from front panel rate ASI bit rate A-17 specifications, audio A-14 A-15 layer II encoding statmux A-16 overview TS bit rate A-17 specifications video data bit rate A-14 A-15 LEDs...

  • Page 129

    This document includes various trademarks of Cisco Systems, Inc. Please see the Notices section of this document for a list of the Cisco Systems, Inc. trademarks used in this document. Product and service availability are subject to change without notice.

Comments to this Manuals

Symbols: 0
Latest comments: