System settings Appendices Table of contents Thank you for choosing Cisco! Your Cisco product has been designed to give you many years of safe, reliable operation. Introduction ........................4 User documentation and software ..................5 This part of the product documentation is aimed at administrators What’s new in CE8 ........................
► User documentation on the Cisco web site Refer to the appendix for more information about the guides for this endpoint. Downloading the user documentation We recommend you visit the Cisco web site regularly for updated versions of the guides: ► http://www.cisco.com/go/mx-docs Software Download software for the endpoint from the Cisco web site: ► ...
MX200 G2 and MX300 G2 at a glance (page 1 of 3) Cisco TelePresence® MX200 G2 and MX300 G2 are part of the MX200 G2 and MX300 G2 systems are easy to install, so you can second generation of MX Series multipurpose endpoints.
15 dB, in steps of 0.5 dB). If set to 0 the audio is switched off. it is turned off. You can use this value if you are only using Cisco microphones, because the video system automatically detects if such a microphone is connected.
Active control is a feature that allows conference participants to administer a conference Define if the microphone shall be muted when an incoming call is automatically answered. on Cisco TelePresence Server using the video system's interfaces. Each user can see Requires that AutoAnswer Mode is switched on.
BestEffort: The system will use encryption whenever possible. H320: All calls are set up as H.320 calls (only applicable if connected to Cisco > In Point to point calls: If the far end system supports encryption (AES-128), the call will TelePresence ISDN Link).
If registered to a Cisco TelePresence Video Communication Server (VCS), the video system Conference IncomingMultisiteCall Mode can use its own built-in MultiSite feature. If registered to a Cisco Unified Communications Manager (CUCM) version 8.6.2 or newer, the video system can use either the CUCM Select whether or not to allow incoming calls when already in a call/conference.
Define the Peap (Protected Extensible Authentication Protocol) mode. Authenticates LAN Define the static IPv4 network address for the system. Applicable only when Network IPv4 clients without the need for client certificates. Developed by Microsoft, Cisco and RSA Assignment is set to Static.
Default value: Auto Value space: Auto/Manual/Off Auto: The Cisco Discovery Protocol (CDP), if available, assigns an id to the voice VLAN. If CDP is not available, VLAN is not enabled. Manual: The VLAN ID is set manually using the Network VLAN Voice VlanId setting. If CDP is available, the manually set value will be overruled by the value assigned by CDP.
NetworkServices CDP Mode NetworkServices HTTP Mode Enable or disable the CDP (Cisco Discovery Protocol) daemon. Enabling CDP will make the Define whether or not to allow access to the video system using the HTTP or HTTPS (HTTP endpoint report certain statistics and device identifiers to a CDP-enabled switch. If CDP is Secure) protocols.
These password is "public". If you have the Cisco TelePresence Management Suite (TMS) you variables can then be queried (set to ReadOnly) and sometimes set (set to ReadWrite) by must make sure the same SNMP Community is configured there too.
Peripherals Pairing CiscoTouchPanels RemotePairing Peripherals Pairing Ultrasound Volume MaxLevel In order to use Cisco Touch 10 (touch panel) as user interface for the video system, Touch This setting applies to the Intelligent Proximity feature. Set the maximum volume of the 10 must be either directly connected to the video system or paired to the video system via ultrasound pairing message.
Off: Do not use a phonebook. VCS: The phonebook is located on the Cisco TelePresence Video Communication Server. TMS: The phonebook is located on the Cisco TelePresence Management Suite server. CUCM: The phonebook is located on the Cisco Unified Communications Manager. Phonebook Server  URL Define the address (URL) to the external phone book server.
TMS: Push configurations to the video system from TMS (Cisco TelePresence Management System). GET: Select GET when the provisioning server supports GET. VCS: Push configurations to the video system from VCS (Cisco TelePresence Video POST: Select POST when the provisioning server supports POST. Communication Server).
External Manager address. Only applicable when the endpoint is provisioned by Cisco Unified Communication Manager Requires user role: ADMIN (CUCM) and an alternate CUCM is available for redundancy. Define the address of the alternate CUCM.
In order to use a client, at least one of the Proximity services must be must be On for this setting to take any effect. enabled (refer to the Proximity Services settings). In general, Cisco recommends enabling all the Proximity services.
ICE (Interactive Connectivity Establishment, RFC 5245) is a NAT traversal solution that the When registered to a Cisco Unified Communications Manager (CUCM) the endpoint may be endpoints can use to discover the optimized media path. Thus the shortest route for audio part of a shared line.
Experimental settings The Experimental settings are for testing only and should not be used unless agreed with Cisco. These settings are not documented and WILL change in later releases. D15332.01 MX200 G2 and MX300 G2 Administrator Guide CE8.0, NOVEMBER 2015.
All images in these materials are for representational purposes only, actual products may differ. Cisco and the Cisco Logo are trademarks of Cisco Systems, Inc. and/or its affiliates in the U.S. and other countries. A listing of Cisco’s trademarks can be found at www.cisco.com/go/trademarks. Third party trademarks mentioned are the property of their respective owners.
Cisco and the Cisco logo are trademarks or registered trademarks of Cisco and/or its affiliates in the U.S. and other countries. To view a list of Cisco trademarks, go to this URL: www.cisco.com/go/ trademarks. Third-party trademarks mentioned are the property of their respective owners. The use of the word partner does not imply a partnership relationship between Cisco and any other company.