Upgrading the system software..........48 Our main objective with this Administrator guide is to address Cisco TelePresence MX200 G2 and MX300 G2 at a glance ..7 Adding option keys ..............49 your goals and needs. Please let us know how well we How to use Touch 10 ...............10...
• Cisco TelePresence MX300 G2 • Administering TC Endpoints on CUCM: Tasks to perform to start using the product with the Cisco Unified Communications Manager (CUCM) Note that the first generation of MX series products (MX300 • Administrator guide (this guide): and MX200) are covered in a separate guide.
System settings Setting passwords Appendices Cisco TelePresence MX200 G2 and MX300 G2 at a glance Cisco TelePresence® MX200 G2 and MX300 G2 are part of MX200 G2 and MX300 G2 systems are easy to install, so you the second generation of MX Series multipurpose endpoints.
Reverting to the previously used software version should only be done by a system administrator or in contact with Cisco technical support. We strongly recommend that you backup your system’s log files and configuration before you swap to the other software image.
Set the auto answer mode. Use the Conference AutoAnswer Delay setting if you want the Cisco TelePresence Server using the video system's interfaces (not available from the TRC5 system to wait a number of seconds before answering the call, and use the Conference remote control and on-screen display).
Conference 1 MaxReceiveCallRate: 6000 Example: Sip: All calls are set up as SIP calls. H320: All calls are set up as H.320 calls (only applicable if connected to a Cisco Conference [1..1] MaxTotalTransmitCallRate TelePresence ISDN Link gateway). This configuration applies when using a video system's built-in MultiSite feature (optional) to...
Allow: You will be notified when someone calls you while you are already in a call. You can If registered to a Cisco Unified Communications Manager (CUCM) version 8.6.2 or newer, the accept the incoming call or not. The ongoing call may be put on hold while answering the video system can use either the CUCM conference bridge, or the video system's own built-in incoming call;...
Network [1..1] DHCP RequestTFTPServerAddress Enter the static IPv6 network address for the system. This setting is only applicable when the This setting is used only for video systems that are registered to a Cisco Unified Network IPv6 Assignment is set to Static.
Set the network traffic control mode to decide how to control the video packets transmission Set the Peap (Protected Extensible Authentication Protocol) mode. Authenticates LAN clients speed. without the need for client certificates. Developed by Microsoft, Cisco and RSA Security. Requires user role: ADMIN Requires user role: ADMIN Value space: <Off/On>...
Requires user role: ADMIN Value space: <Auto/Manual/Off> Auto: The Cisco Discovery Protocol (CDP), if available, assigns an id to the voice VLAN. If CDP is not available, VLAN is not enabled. Manual: The VLAN ID is set manually using the Network VLAN Voice VlanId setting. If CDP is available, the manually set value will be overruled by the value assigned by CDP.
NetworkServices CDP Mode NetworkServices SIP Mode Enable or disable the CDP (Cisco Discovery Protocol) daemon. Enabling CDP will make the Determine whether the system should be able to place and receive SIP calls or not. endpoint report certain statistics and device identifiers to a CDP-enabled switch. If CDP is Requires user role: ADMIN disabled, the Network VLAN Voice Mode: Auto setting will not work.
Example: NetworkServices Medianet Metadata NetworkServices SNMP Mode Switch On or Off the capability to tag media flows with metadata related to the Cisco Medianet deployment. SNMP (Simple Network Management Protocol) is used in network management systems to monitor network-attached devices (routers, servers, switches, projectors, etc) for conditions Requires user role: ADMIN that warrant administrative attention.
SNMP Agent in the codec. The default password is "public". Requires user role: ADMIN If you have the Cisco TelePresence Management Suite (TMS) you must make sure the same SNMP Community is configured there too. NOTE: The SNMP Community password is case Value space: <Off/On>...
NetworkServices CTMS Encryption This setting indicates whether or not the video system supports encryption when participating in a multiparty meeting controlled by a Cisco TelePresence Multipoint Switch (CTMS). CTMS allows three security settings for meetings: non-secure (not encrypted), best effort (encrypted if all participants support encryption, otherwise not encrypted) and secure (always encrypted).
Peripherals settings Peripherals Pairing CiscoTouchPanels RemotePairing In order to use Cisco Touch 10 (touch panel) as user interface for the video system, Touch 10 must be either directly connected to the video system or paired to the video system via LAN.
VCS: Select VCS if the phonebook is located on the Cisco TelePresence Video Communication Server. TMS: Select TMS if the phonebook is located on the Cisco TelePresence Management Suite server. Callway: Select Callway if the phonebook is to be provided by the WebEx TelePresence subscription service (formerly called CallWay).
Select the HTTP method to be used for the provisioning. Auto: The provisioning server will automatically be selected by the video system. Requires user role: ADMIN TMS: The video system will be configured using TMS (Cisco TelePresence Management System). Value space: <GET/POST>...
Value space: <S: 0, 64> Format: String with a maximum of 64 characters. Only applicable when the endpoint is provisioned by Cisco Unified Communication Manager (CUCM) and an alternate CUCM is available for redundancy. Enter the address of the alternate Provisioning ExternalManager Domain: "any.domain.com"...
Requires user role: ADMIN Value space: <Standard/Cisco> Value space: <Off/On> Standard: Use this when registering to standard SIP Proxy (tested with Cisco TelePresence Off: Connect to the single proxy configured first in Proxy Address list. VCS and Broadsoft) On: Set up multiple outbound connections to servers in the Proxy Address list.
LocalDeviceOnly: Snapshots can only be captured and displayed on devices running the Video Input Connector [1..4] Name experimental Cisco Proximity feature. The devices must be in the same room as the video system. It will not be possible to take and see snapshots on the web interface or by using Enter a name for the video input connector.
Appendices Experimental settings The Experimental settings are for testing only and should not be used unless agreed with Cisco. These settings are not documented and WILL change in later releases. D15078.04 MX200 G2 and MX300 G2 Administrator Guide TC7.3, DECEMBER 2014.
Read the Cisco TMS Provisioning Deployment Guide to find this guide. Examples showing either the default value or an how to upload the file to Cisco TMS, and how to set the example value are included. desired values for the parameters to be provisioned. If not set by Cisco TMS, the default values will be used.
In an error situation it may be required to factory reset Factory resetting Touch 10 the Touch 10 user interface to recover connectivity. This should be done only when in contact with the Cisco support 1. Locate the Mute Volume down buttons.
All images in these materials are for representational purposes only, actual products may differ. Cisco and the Cisco Logo are trademarks of Cisco Systems, Inc. and/or its affiliates in the U.S. and other countries. A listing of Cisco’s trademarks can be found at www.cisco.com/go/trademarks. Third party trademarks mentioned are the property of their respective owners.
Setting passwords Appendices Appendices User documentation on the Cisco web site In general, user documentation for the Cisco TelePresence products is available here: The documents are organized in the following categories: http://www.cisco.com/go/telepresence/docs Installation guides: Install and Upgrade > Install and Upgrade Guides You have to choose your product category in the right pane until you find your product.
Tandberg ASA. Cisco and the Cisco logo are trademarks or registered trademarks of Cisco and/or its affiliates in the U.S. and other countries. To view a list of Cisco trademarks, go to this URL: www.cisco.com/go/trademarks. Third- party trademarks mentioned are the property of their respective owners.