Page 1 HP StorageWorks Director 2/140 installation guide FW 07.00.00/HAFM SW 08.06.00 Part number: AA–RTDSD–TE/958-000275-003 Fourth edition: March 2005...
Page 2 Hewlett-Packard. The information is provided “as is” without warranty of any kind and is subject to change without notice. The only warranties for HP products and services are set forth in the express warranty statements accompanying such products and services.
Page 3: Table Of Contents
HP-authorized reseller ........
Page 4 Installing the shelf brackets in HP 9000, HP 10000, and HP 11000 Series racks ..33 Installing shelf brackets in an HP Rack system/e or 19-inch EIA rack ....35 Attaching the mounting hardware to the director .
Page 5 R_A_TOV ............56 E_D_TOV .
Page 6 Carton contents for a Director 2/64......... . 31 Carton contents for an HP 9000, HP 10000, and HP 11000 Series rack ....31 10 Carton contents for a HP system/e or industry-standard 19-in rack installation.
Page 7 16 Mounting anti-tip feet for a HP system/e rack ....... .
Page 8 Shipping carton contents for an HP 9000, HP 10000, and HP 11000 Series rack ..32 Parts for Installing in an HP System/e and industry-standard 19-inch rack ... . . 33 Director operational states and symbols .
Page 9: About This Guide
This guide provides information about installing, configuring, managing, and verifying operation of the HP StorageWorks Director 2/140. The director switch connects storage devices, hosts, and servers in a SAN. The director is easily managed and configured to optimize the performance of your SAN.
Page 10: Document Conventions And Symbols
Convention Element Medium blue text: Figure 1 Cross-reference links and e-mail addresses Medium blue, underlined text Web site addresses (http://www.hp.com) Bold font • Key names • Text typed into a GUI element, such as into a box • GUI elements that are clicked or selected, such as menu and...
Page 11: Rack Stability
Extend only one rack component at a time. Racks may become unstable if more than one component is extended. HP technical support Telephone numbers for worldwide technical support are listed on the HP support web site: http://www.hp.com/support/ Collect the following information before calling: Technical support registration number (if applicable) •...
Page 12 • http://www.hp.com • http://www.hp.com/go/storage • http://www.hp.com/support/ • http://www.docs.hp.com...
Page 13: Overview
Overview This chapter contains the following HP StorageWorks Director 2/140 information: • Director description, page 13 • Features, page 13 • Hardware components, page 17 • Tools and test equipment, page 22 • Optional kits, page 24 Director description The director is a second-generation, 140-port product that provides dynamic switched connections between Fibre Channel servers and devices in a SAN environment.
Page 14: Error-Detection, Reporting, And Serviceability
The CLI is not an interactive interface; no checking is done for pre-existing conditions and no prompts display to guide users through tasks. Refer to the HP StorageWorks CLI reference guide for directors and edge switches for more information.
Page 15 Element Manager on the HAFM appliance to receive unsolicited SNMP trap messages. The trap messages indicate operational state changes and failure conditions. NOTE: For more information about SNMP support provided by HP products, refer to the HP StorageWorks SNMP reference guide for directors and edge switches. Director 2/140 installation guide...
Page 16: Zoning
Zoning The director supports a name server zoning feature that partitions attached devices into restricted-access groups called zones. Devices in the same zone can recognize and communicate with each other through switched port-to-port connections. Devices in separate zones cannot communicate with each other. Zoning is configured by authorizing or restricting access to name server information associated with device N_Ports that attach to director fabric ports (F_Ports).
Page 17: Hardware Components
• Fabric A unzoned and Fabric B unzoned—The fabrics join successfully, and the resulting fabric remains unzoned. • Fabric A zoned and Fabric B unzoned—The fabrics join successfully, and fabric B automatically inherits the zoning configuration from fabric A. • Fabric A unzoned and Fabric B zoned—The fabrics join successfully, and fabric A automatically inherits the zoning configuration from fabric B.
Page 18: Front View
Front view Figure 1 shows Director 2/140 components accessible from the front of the director. Component descriptions follow the figure. Front bezel UPM cards (32) Power and system error LEDs CTP cards Figure 1 Director components—front CTP card The Director 2/140 ships with two Control Processor (CTP) cards. The active CTP card initializes and configures the director after power on, and contains the microprocessor and associated logic that coordinate director operation.
Page 19: Power/System Led Assembly
Each card faceplate contains a green light emitting diode (LED) that turns O if the card is operational and active, and an amber LED that turns O if the card fails. The LEDs are O on the backup CTP. The amber LED F if beaconing is enabled.
Page 20: Upm Card Leds And Connectors
(2 to 500 meters) through 50-μm (500 meters) or 62.5-μm (200 meters) multi-mode fiber. NOTE: HP recommends 50-μm fiber-optic cable for any new installation requiring multi-mode fiber. • Long-wave laser—Long-wave laser transceivers provide connections for transferring data over long distances (up to 10 kilometers) through 9-μm single-mode fiber.
Page 21: Rear View
Rear view Figure 3 shows the components accessible from the rear of the Director 2/140 . Fan modules SBAR assemblies UPM cards (3) AC modules Maintenance port Power supplies Figure 3 Director components—rear Fan modules Three fan modules, each containing one system fan (three system fans total), provide cooling for director FRUs, as well as provide redundancy for continued operation if a fan fails.
Page 22: Ac Module
Do not use an Allen wrench or torque tool designed for use with another HP product. Use of the wrong tool may overtighten and damage logic cards.
Page 23: Loopback Plug
• Loopback plug—An SFP multi-mode (short-wave laser) or single-mode (long-wave laser) loopback plug (Figure 5), is required to perform port loopback diagnostic tests. One loopback plug is shipped with the director, depending on the type of port transceivers installed. Both plugs are shipped if short-wave laser and long-wave laser transceivers are installed.
Page 24: Tools Supplied By Service Personnel
Fiber-optic cleaning kit—The kit contains tools and instructions to clean fiber-optic cable, connectors, loopback plugs, and protective plugs. Optional kits Contact your HP authorized service provider to purchase the following optional director kits. See Table 2 for descriptions of Director 2/140 optional kits.
Page 25 Table 2 Director optional kits (continued) Supporting kit Description 35km Extended Reach Optical Provides 35km long-wave optical transceiver for the Transceiver Kit, director. Part Number: 300836-B21 2Gb UPM Port Module Kit, Provides 4 additional short-wave ports for the Part Number: 316094-B21 Director 2/140.
Page 26 Overview...
Page 27: Installing And Configuring The Director
LAN addressing issues must be considered. Review installation requirements The director is delivered stand-alone and ready to be mounted in an HP 9000, HP 10000, HP 11000, HP system/e, or industry-standard 19-in rack. Ethernet cabling, distance, and LAN addressing issues must be considered.
Page 28: Items Required For Installation
Lift device (recommended). • Director 2/140. • An HP 9000, HP 10000, HP 11000, HP system/e, or industry-standard 19-in rack, or any rack with the following specifications: • A minimum depth of 24.5 in. • 19 in wide. • A minimum opening size of 13U available (12U for the director and 1U for space recommended for routing of cables).
Page 29: Select An Operating Location
• Maintenance terminal (desktop or notebook computer)—required to configure director network addresses and acquire event log information through the maintenance port. Computer requirements include: • Microsoft Windows 98, Windows Millennium Edition, Windows NT 4.0, Windows 2000, or Windows XP operating system installed. •...
Page 30: Install The Director On A Desktop
AC power connections (director) WARNING! An HP-supplied power cord is provided for each director power supply. To prevent electric shock when connecting the director to primary facility power, use only the supplied power cord(s), and ensure the facility power receptacle is the correct type, supplies the required voltage, and is properly grounded.
Page 31: Install The Director In A Rack
After successful POST completion, the green power LED on the front bezel, green LED on the active CTP card, and green PWR OK LEDs on both power supplies remain illuminated. If a POST error or other malfunction occurs, refer to the HP StorageWorks Director 2/140 service manual to isolate the problem.
Page 32: Required Items
Consider leaving a space of 1U open above and below each director to allow easier cabling access. • HP recommends installing an optional power distribution unit (PDU) in the bottom of the rack. HP ships two PDU power cords with the Director 2/140. •...
Page 33: Installing The Shelf Brackets In The Rack
”Installing shelf brackets in an HP Rack system/e or 19-inch EIA rack” on page 35. Installing the shelf brackets in HP 9000, HP 10000, and HP 11000 Series racks Use these steps to install the two shelf brackets in an HP 9000, HP 10000, or HP 11000 Series rack.
Page 34 Figure 10 Angle brackets mounted on cabinet rails in HP 9000, HP 10000, and HP 11000 Series rack Attach two shelf brackets to the angle brackets on each side of the cabinet using eight (8) pan...
Page 35: Installing Shelf Brackets In An Hp Rack System/E Or 19-Inch Eia Rack
”Attaching the mounting hardware to the director” on page Installing shelf brackets in an HP Rack system/e or 19-inch EIA rack The shelf brackets mount directly to the interior vertical rails of the HP rack system/e or 19-inch EIA rack using cage nuts and Phillips panhead screws.
Page 36: Attaching The Mounting Hardware To The Director
Repeat step 4 for each of the three remaining interior vertical rails. Secure a shelf bracket to the interior vertical rails using four (4) Phillips panhead screws with split lock and flat washers. Repeat step 6 to secure the second shelf bracket on the opposite side of the rack. Continue to ”Attaching the mounting hardware to the director”...
Page 37: Inserting The Rear Cage Nuts In The Rack
Select one of the exterior vertical rails at the front of the cabinet. From the bottom of the shelf bracket, count up 3U (9 holes) and insert the first of three cage nuts. Count up 3U (9 holes) from the cage nut you just installed and insert the next cage nut. Count up 3U (9 holes) from the second cage nut and insert the third cage nut.
Page 38: Connecting The Director To A Power Source
NOTE: The 110-volt AC power cords provided in the kit are not for use with the Director 2/140. For more information, see the HP StorageWorks director power cord advisory. WARNING! To prevent electric shock, use only the supplied PDU power cord(s). Also, verify that the facility power receptacle is the correct type, supplies the required voltage, and is properly grounded.
Page 39: Power-On Self Test
After successful POST completion, the green power LED on the front bezel, green LED on the active CTP card, and green PWR OK LEDs on both power supplies remain If a POST error or other malfunction occurs, refer to the HP StorageWorks Director 2/140 service manual.
Page 40: Changing The Director's Ip Address
NOTE: If multiple directors and the HAFM appliance are delivered in an HP-supplied equipment cabinet, all devices are configured with unique IP addresses that do not require change. The addresses require change only if multiple equipment cabinets are LAN-connected.
Page 41: Ac Power Connections
Remove the protective cap from the 9-pin maintenance port at the rear of the director (a flat-tip screwdriver may be required). See Figure 14 Maintenance port Null Modem cable RS-232 port Figure 14 Connecting the null modem cable between the director and a workstation Connect the 9-pin end of the RS-232 modem cable to the maintenance port.
Page 42: Connection Description Dialog Box
The Connection Description dialog box appears (Figure 15). Figure 15 Connection Description dialog box Enter 2140 in the Name box and click OK. The Connect To dialog box appears (Figure 16). Figure 16 Connect To dialog box Ensure the Connect using box displays COM1 or COM2 (depending on the serial communication port connection to the director) and click OK.
Page 43: Hyperterminal Window
• Bits per second: 115200 • Data bits: 8 • Parity: None • Stop bits: 1 • Flow control: Hardware Click OK. The HyperTerminal window appears. At the > prompt, enter the user-level password (the default is password) and press Enter. The password is case-sensitive.
Page 44: Lan-Connect The Director
When the new network addresses are configured at the director, the message Request completed OK appears at the bottom of the HyperTerminal window. 13.Select Exit from the File menu. A HyperTerminal dialog box appears (Figure 19). Figure 19 HyperTerminal dialog box (1) 14.Click Yes.
Page 45: Hafm Appliance
If an HAFM appliance is not available, use the Embedded Web Server (EWS) interface. Attach the Ethernet LAN segment to an Internet connection. HAFM appliance To run HAFM software, you must set up and configure the HAFM appliance. Refer to the HP StorageWorks HA-Fabric Manager appliance installation guide for instructions on: •...
Page 46: Record Or Verify Hafm Appliance Restore Information
The Windows 2000 operating system and the HAFM and director Element Manager must also be restored. Refer to the HP StorageWorks Director 2/140 service manual for instructions. To record or verify HAFM appliance configuration information, refer to the HP StorageWorks HA-Fabric Manager appliance installation guide for instructions.
Page 47: Verify Communication Between The Director And Hafm Appliance
71. • If director operation is displayed as degraded or a director failure is indicated (FRU alert symbols and a yellow triangle or red diamond at the alert panel), refer to the HP StorageWorks Director 2/140 service manual.
Page 48: Set Director Date And Time
In the example, the director’s status is operational as indicated by the green circle in the alert panel. Figure 24 Hardware View page Set director date and time The Director Element Manager log entries are stamped with the date and time received from the director.
Page 49: Set Date And Time Manually
• Synchronize date and time, page 49 Figure 25 Configure Date and Time dialog box Set date and time manually Use these steps to set the director date and time manually: At the Configure Date and Time dialog box, select the Periodic Date/Time Synchronization box to deselect the option (no check in the box).
Page 50: Frequently Used Hafm Settings
Frequently used HAFM settings This section summarizes the most common HAFM tasks including: NOTE: For a complete reference on HAFM functionality, refer to the HAFM user guide. • Setting the director online, page 50 • Setting the director offline, page 51 •...
Page 51: Setting The Director Offline
If the director is offline, the Set Online State dialog box appears, indicating the status is Offline. Click Set Online. A Warning dialog box appears, indicating status is online. Click OK. The Status table appears Online. Setting the director offline When the director is set offline, all ports are set offline.
Page 52: Configuring Director Management Style
LAN, the name should reflect the director’s Ethernet network DNS host name. For example, if the DNS host name is SAN140.hp.com, the name entered in this dialog box is SAN140. Enter a director description of 255 or fewer alphanumeric characters in the Description box.
Page 53: Switch Parameters
CAUTION: Setting the director offline terminates all Fibre Channel connections. Select Configure > Operating Parameters > Switch Parameters. The Configure Switch Parameters dialog box appears (Figure 28). Figure 28 Configure Switch Parameters dialog box Ordinarily, you do not need to change values in this dialog box from their defaults. The only exception is the Preferred Domain ID.
Page 54: Insistent
domain ID is already allocated, an unused domain ID is assigned. Note that you must set the director offline before you can change to the preferred domain ID. The preferred domain ID must be unique for each director and switch in a fabric. If two switches or directors have the same preferred domain ID, the E_Ports segment, causing the fabric to segment.
Page 55: Suppress Rscns On Zone Set Activations
and storage device vendor to determine if enabling Domain RSCNs will cause problems with your HBA or storage products. NOTE: This option is required if Enterprise Fabric Mode (optional SANtegrity Binding feature) is enabled. The default state is enabled. Suppress RSCNs on zone set activations Fabric format domain register for state change notifications (RSCNs) are sent to ports on the switch following any change to the fabric's active zone set.
Page 56: Fabric Parameters
After you change settings, click Activate. Back up the configuration data when you are finished configuring the switch. Set the director online. For instructions, see ”Setting the director online” on page 50. Fabric parameters Configure the following parameters as required by your fabric. BB_Credit Configure the director to support buffer-to-buffer credit (BB_Credit) from 1 through 60.
Page 57: Interop Mode
ISLs will segment. NOTE: HP recommends you leave the switch priority setting as Default. If you are considering setting this value to something other than default, refer to the section on principal switch selection for multi-switch fabrics in the HP StorageWorks SAN high availability planning guide for details.
Page 58: Configuring Switch Binding
This provides security in environments that include a large number of devices by ensuring that only the intended set of devices attach to a switch or director. For complete procedures on configuring this optional feature, refer to HP StorageWorks Director Element Manager user guide.
Page 59 NOTE: If the director supports BB_Credits by port, the 10-100 Km column is replaced by an RX BB Credit column. d. If the director supports BB_Credits by port, right-click the RX BB Credit column. The RX BB Credits dialog box appears. NOTE: The port must be offline to change the BB_Credit field.
Page 60: Configuring Port Addresses (Ficon)
If the director is set to FICON management style, perform this procedure to access the director matrix and define Fibre Channel port names, configure ports as blocked or unblocked, and define the CUP name. For instructions on configuring port addresses, refer to HP StorageWorks Director Element Manager user guide for details.
Page 61: Configuring And Enabling E-Mail Notification
Enter the IP address or DNS host name of the trap recipient (SNMP management workstation) in the associated Trap Recipient box. Use 64 or fewer alphanumeric characters. HP recommends using the IP address. d. Enter a decimal user datagram protocol (UDP) port number in the associated UDP Port Number box.
Page 62 The Email Event Notification Setup dialog box appears (Figure 32). Figure 32 Email Event Notification Setup dialog box To enable e-mail transmission of configured addresses, select Enable Email Event Notification. A check appears in the box when transmission is enabled. NOTE: The enable function must be activated for each director or switch through the Element Manager.
Page 63: Define Filter Dialog Box
The HAFM 8.6 Server Users dialog box appears (Figure 33). Figure 33 HAFM 8.6 Server Users dialog box To enable e-mail notification for a user, select the box in the Email column. An unchecked box indicates e-mail notification is not enabled. To configure event types for which e-mail notification is sent, select the Filter link adjacent to the check box.
Page 64: Configuring And Enabling Call-Home Features
Configuring and enabling call-home features There are two call-home features available, and one is installed with the HAFM application. To learn more about configuring call-home features, refer to the HP StorageWorks HA-Fabric Manager appliance installation guide. Configuring and enabling Ethernet events Perform this procedure to configure and enable Ethernet events.
Page 65: Creating New Alerts
• A yellow triangle appears by the Threshold Alerts box in the Port Properties dialog box. • Detailed threshold alert data is recorded in the Threshold Alert Log. Use the Threshold Alerts option on the Configure menu to configure the following: •...
Page 66: New Threshold Alerts Dialog Box—First Screen
The New Threshold Alert dialog box appears (Figure 37). Figure 37 New Threshold Alerts dialog box—first screen Enter a name from one to 64 characters in length. All characters in the ISO Latin-1 character set, excluding control characters, are allowed. Select one of the following from the Threshold Type list: •...
Page 67: New Threshold Alerts Dialog Box—Second Screen
NOTE: Click Previous if you need to return to the previous screen. Figure 38 New Threshold Alerts dialog box—second screen Enter a percentage from 1 through 100 for % utilization. When throughput reaches this percentage of port capacity, a threshold alert will occur. Enter the amount of cumulative minutes in which the % utilization should exist during the notification interval before an alert is generated.
Page 68: New Threshold Alerts Dialog Box—Third Screen
A new screen appears for selecting ports for the alerts (Figure 39). Figure 39 New Threshold Alerts dialog box—third screen 10.Select either Port Type or Port List. • If you select Port Type, selecting either E_Ports or F_Ports to cause an alert to generate for all ports configured as E_Ports or F_Ports, respectively.
Page 69: Modifying Alerts
Figure 40 New Threshold Alerts dialog box—summary screen 12.Click Finish. The Configure Threshold Alerts dialog box appears (Figure 41). Figure 41 Configure Threshold Alerts dialog box 13.At this point, the alert is not active. To activate the alert, select the alert information that appears in the Configure Threshold Alerts list and then click Activate.
Page 70: Activating Or Deactivating Alerts
At the summary screen, click Finish. Activating or deactivating alerts Use the following steps to activate or deactivate existing threshold alerts. In the active state, notifications are generated for the alert. In the inactive state, notifications do not occur. At the Hardware View page, select Configure > Threshold Alerts. The Configure Threshold Alerts dialog box appears.
Page 71: Configuring Open Systems Management Server
Refer to the HP StorageWorks HA-Fabric Manager Appliance installation guide for instructions on backing up the HAFM configuration data. Configuring Open Systems Management Server For complete procedures on configuring this optional feature, refer to the HP StorageWorks Director Element Manager user guide. Configuring FICON Management Server For complete procedures on configuring this optional feature, refer to the HP StorageWorks Director Element Manager user guide.
Page 72: Enabling Embedded Web Server
Select Enable Web Server again to remove the check and disable the EWS interface. When disabled, remote users cannot access the interface. For complete procedures on using EWS, refer to the HP StorageWorks Embedded Web Server user guide. Enabling Telnet Use the following steps to enable Telnet: At the Hardware View, select Configure >...
Page 73: Unpacking, Inspecting, And Installing The Ethernet Hub (Optional)
10/100 Mbps LAN segment. One hub port is required to connect the HAFM appliance, and one hub port is required to connect each director. A combination of up to 48 HP directors or switches can be configured and managed by a single HAFM appliance, therefore multiple hubs may be required to provide sufficient port connections.
Page 74: Remote Workstation Minimum Requirements
• Linux-based system using an Intel Pentium III processor with a 1 gigahertz (GHz) or greater clock speed, using the Red Hat® 7.3 or higher operating system. • HP PA-RISC processor with a 400 MHz or greater clock speed, using the HP-UX 11 or higher operating system.
Page 75: Launching Hafm From The Remote Client
b. Download SNMP MIB files—The Management Information Base (MIB) files are provided in standard ASN.1 syntax and may be installed into the MIB database of any SNMPv2 compliant Network Management Station. Figure 44 HAFM remote client install If you selected Install HAFM remote client application, follow the instructions provided that pertains to your platform.
Page 76: Hafm 8.6 Log In Dialog Box
NOTE: The default Windows 2000 user name is Administrator and the default password is password. The user name and password are case-sensitive. Figure 45 HAFM 8.6 Log In dialog box Enter the HAFM appliance IP address in the Network Address box. •...
Page 77 The View All - HAFM 8.6 window appears (Figure 46). Figure 46 View All - HAFM 8.6 window Director 2/140 installation guide...
Page 78 Installing and configuring the director...
Page 79: Managing Firmware Versions
Managing firmware versions The director 2/140 internal operating code is downloaded from the HAFM appliance and stored on a CTP card. Up to eight (8) versions can be stored on the HAFM appliance hard drive and made available for download to a director. This chapter contains information on the following firmware management tasks: •...
Page 80: Adding A Firmware Version
Adding a firmware version The firmware version shipped with the director is provided on the director documentation CD. Subsequent firmware versions to upgrade the director are provided to customers through the HP website. NOTE: When adding firmware, follow procedural information in the release notes that accompany the firmware version.
Page 81: Modifying A Firmware Version Description
New Firmware Description dialog box Enter a description (up to 24 characters in length) for the new firmware version and click OK. HP recommends the description include the installation date and text that uniquely identifies the firmware version. A Transfer Complete message box appears indicating the new firmware version is stored on the HAFM appliance hard drive.
Page 82: Deleting A Firmware Version
The Modify Firmware Description dialog box appears. Enter a modified description (up to 24 characters in length) for the firmware version and click HP recommends that you include the installation date and text that uniquely identifies the firmware version in the description.
Page 83 Use these steps to download a firmware version to a director: Open the HAFM application. The View All - HAFM 8.6 main window appears. Before downloading firmware to a director, ensure the required, compatible version of the HAFM application is running on the HAFM appliance. Refer to the release notes that shipped with HAFM.
Page 84: Backing Up The Director's Configuration
If a problem occurs and a corresponding message appears, refer to the HP StorageWorks Director 2/140 service manual for specific information on isolating the problem. If no error occurs, the Send Firmware confirmation box appears. Click Yes. The Send Firmware dialog box appears.
Page 85: A Regulatory Compliance And Safety
Regulatory compliance and safety Regulatory compliance Federal Communications Commission notice Part 15 of the Federal Communications Commission (FCC) Rules and Regulations has established Radio Frequency (RF) emission limits to provide an interference-free radio frequency spectrum. Many electronic devices, including computers, generate RF energy incidental to their intended function and are, therefore, covered by these rules.
Page 86: Declaration Of Conformity For Products Marked With The Fcc Logo, United States Only
Laser device All HP systems equipped with a laser device comply with safety standards, including International Electrotechnical Commission (IEC) 825. With specific regard to the laser, the equipment complies with laser product performance standards set by government agencies as a Class 1 laser product.
Page 87: Laser Safety Warning
Laser product label The optional label in Figure 51 or equivalent may be located on the surface of the HP supplied laser device. This optional label indicates that the product is classified as a CLASS 1 LASER PRODUCT. This label may appear on the laser device installed in your product.
Page 88: Class B Equipment
Class B equipment This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations. Cet appareil numérique de la classe B respecte toutes les exigences du Règlement sur le matériel brouilleur du Canada. European Union notice Products bearing the CE marking comply with the EMC Directive (89/336/EEC) and the Low Voltage Directive (73/23/EEC) issued by the Commission of the European Community and if this product has telecommunication functionality, the R&TTE Directive (1999/5/EC).
Page 89: Japanese Notice
There is a danger of explosion and risk of personal injury if the battery is incorrectly replaced or mistreated. Replacement is to be done by an HP authorized service provider using the HP spare part designated for this product. For more information about battery replacement or proper disposal, contact an HP authorized reseller or HP authorized service provider.
Page 90: Taiwan Battery Recycling Notice
1.00 mm or 18 AWG, and the length of the cord must be between 1.8 m (6 ft) and 3.6 m (12 ft). If you have questions about the type of power cord to use, contact an HP authorized service provider.
Page 91: Japanese Power Cord Notice
Use conductive field service tools. • Use a portable field service kit with a folding static-dissipating work mat. If you do not have any of the suggested equipment for proper grounding, have an HP authorized reseller install the part. NOTE: For more information on static electricity, or assistance with product installation, contact your HP authorized reseller.
Page 92 Regulatory compliance and safety...
Page 93: B Technical Specifications
61.0 cm (24.2 in) Weight 75.9 kg (167 lb) Shipping Weight 102.1 kg (225 lb) Environmental specifications Table 5 lists environmental ranges for shipping, storing, and operating the HP StorageWorks Director 2/140. Table 5 Environmental specifications Specification Shipping Storage Operating Weight 102.1 kg (225 lb)
Page 94: Power Requirements
Power requirements Table 6 lists Director 2/140 power requirements. Table 6 Power requirements Specification Value Input voltage 180 to 264 VAC Input current 4.66 amps at 180 VAC Input power 842 watts Input frequency 47/63 Hz Operating tolerances Table 7 lists heating and cooling specifications, shock and vibration tolerances, acoustical noise, and inclination.
Page 95: Laser Information
Laser information Three configurations of cards with fixed optics will be provided for each of the connector types: four extended long-wave ports, four long-wave ports, and four short-wave ports. Table 8 lists the 2 Gb laser specifications. Table 8 Laser specs - 2 Gb Part number Transceivers on Wave...
Page 96 Technical specifications...
Page 97: Index
COMn properties dialog box asynchronous RS-232 components of the director null modem cable configuration data, backing up authorized reseller, HP configure director network information Avis Canadien, regulatory compliance configure fabric parameters dialog box notice configure feature key dialog box...
Page 98 degraded fabric performance, causes of rerouting delay diagnostic software, introduction E_port segmentation dialog boxes preferred domain ID configure fabric parameters e_port segmentation configure feature key causes of procedure e_ports configure switch parameters 52, electrostatic damage prevention director electrostatic discharge. See ESD AC module e-mail notification connecting to power...
Page 99 AC module storage web site FRUs, CTP card Subscriber’s choice web site technical support telephone number FCC questions g_ports HP-UX operating system UPM card HyperTerminal 24, German noise declaration ground strap specifications grounding methods IEC EMC, worldwide regulatory compliance notice...
Page 100 installation tasks single-mode backing-up configuration data director unpacking, inspecting, installing MAC address recording and verifying HAFM appliance maintenance port 15, restoration information management server unpacking, inspecting, and installing FICON Ethernet hub open systems Intel Pentium processor management style Internet Explorer FICON interop mode open systems...
Page 101 BSMI OSI devices, communication Canada Class A Class B European Union parts HP series number proper handling IEC EMC statement, worldwide storing Japan transporting Korean password lasers default Windows 2000 modifications...
Page 102 UltraSPARC-II processor heel UNIX workstation, specifications UPM cards Subscriber’s choice, HP user name SunOS operating system default Windows 2000 suppress RSCNs on zone set activations switch error-detection, reporting, and serviceability versions features...
Page 103 HP storage HP Subscriber’s choice weight, director caution Windows 2000 default password default user name Windows operating systems, versions 24, work mat, static-dissipating workstation, UNIX wrist straps specifications using...

HP StorageWorks Director 2/140 Installation Manual

About this Guide

Tables

Overview

Figures

Installing and Configuring the Director

Managing Firmware Versions

A Regulatory Compliance and Safety

B Technical Specifications

Index

Quick Links

Related Manuals for HP StorageWorks Director 2/140

Summary of Contents for HP StorageWorks Director 2/140

Table of Contents