Dodge dakota 2002 Service Manual page 1484

DR
ENGINE - 5.9L (Continued)
(19) Install the distributor cap and wiring.
(20) Install the intake manifold (Refer to 9 -
ENGINE/MANIFOLDS/INTAKE
INSTALLATION).
(21) Using a new gasket, install throttle body
(Refer to 14 - FUEL SYSTEM/FUEL INJECTION/
THROTTLE BODY - INSTALLATION).
(22) Connect the throttle linkage (Refer to 14 -
FUEL SYSTEM/FUEL
CONTROL CABLE - INSTALLATION).
(23) Install the air cleaner resonator and duct
work..
(24) Install the generator and wire connections
(Refer to 8 - ELECTRICAL/CHARGING/GENERA-
TOR - INSTALLATION).
(25) Install a/c compressor and lines (Refer to 24 -
HEATING & AIR CONDITIONING/PLUMBING/A/C
COMPRESSOR - INSTALLATION).
(26) Install the accessory drive belt (Refer to 7 -
COOLING/ACCESSORY DRIVE/DRIVE BELTS -
INSTALLATION).
(27) Install upper radiator support crossmember.
(28) Install radiator (Refer to 7 - COOLING/EN-
GINE/RADIATOR - INSTALLATION).
(29) Connect the radiator lower hose.
(30) Connect the transmission oil cooler lines to
the radiator.
(31) Install the fan shroud.
(32) Install the fan (Refer to 7 - COOLING/EN-
GINE/RADIATOR FAN - INSTALLATION).
(33) Connect the radiator upper hose.
(34) Install the washer bottle.
(35) Install the transmission oil cooler (Refer to 7 -
COOLING/TRANSMISSION/TRANS
INSTALLATION).
(36) Connect the transmission cooler lines.
(37) If equipped, install the condenser (Refer to 24
- HEATING & AIR CONDITIONING/PLUMBING/
A/C CONDENSER - INSTALLATION).
(38) Evacuate and charge the air conditioning sys-
tem, if equipped (Refer to 24 - HEATING & AIR
CONDITIONING/PLUMBING - STANDARD PRO-
CEDURE).
(39) Add engine oil to crankcase (Refer to LUBRI-
CATION & MAINTENANCE/FLUID TYPES - SPEC-
IFICATIONS).
(40) Fill cooling system (Refer to 7 - COOLING -
STANDARD PROCEDURE).
(41) Connect battery negative cable.
(42) Start engine and inspect for leaks.
(43) Road test vehicle.
MANIFOLD
INJECTION/THROTTLE
COOLER
SPECIFICATIONS
-
5.9L ENGINE
ENGINE SPECIFICATIONS
DESCRIPTION
GENERAL SPECIFICATIONS
Engine Type
Bore and Stroke
Displacement
Compression Ratio
Firing Order
Lubrication
Cooling System
Cylinder Block
Cylinder Head
Crankshaft
Camshaft
-
Pistons
Connecting Rods
Compression Pressure
Bearing Diameter
ENGINE - 5.9L
SPECIFICATION
90° V-8 OHV
101.6 x 90.9 mm
(4.00 x 3.58 in.)
5.9L (360 c.i.)
9.1:1
1–8–4–3–6–5–7–2
Pressure Feed – Full
Flow
Filtration
Liquid Cooled – Forced
Circulation
Cast Iron
Cast Iron
Nodular Iron
Nodular Cast Iron
Aluminum Alloy w/strut
Forged Steel
689.5 kPa (100 psi)
(Min.)
CAMSHAFT
No. 1 50.800 – 50.825 mm
(2.000 – 2.001 in.)
No. 2 50.394 – 50.419 mm
(1.984 – 1.985 in.)
No. 3 50.013 – 50.038 mm
(1.969 – 1.970 in.)
No. 4 49.606 – 49.632 mm
(1.953 – 1.954 in.)
No. 5 39.688 – 39.713 mm
(1.5625 – 1.5635 in.)
9 - 235