Parameter List; Primary Motor Settings - Danfoss mcd-500 Operating Instruction

MCD 500 Operating Instruction

7.4.3 Parameter List

1 Primary Mtr Set
1-1 Motor FLC
1-2 Locked Rotor Time
1-3 Start Mode
1-4 Current Limit
1-5 Initial Current
1-6 Start Ramp Time
1-7 Kickstart Level
1-8 Kickstart Time
1-9 Excess Start Time
1-10 Stop Mode
1-11 Stop Time
1-12 Adaptv Control Gain
1-13 Adaptv Start Profile
1-14 Adaptv Stop Profile
1-15 Brake Torque
1-16 Brake Time
2 Protection
2-1 Phase Sequence
2-2 Current Imbalance
2-3 Current Imbal Dly
2-4 Undercurrent
2-5 Undercurrent Dly
2-6 Inst Overcurrent
2-7 Inst Ocrnt Dly
2-8 Frequency Check
2-9 Freq Variation
2-10 Frequency Delay
2-11 Restart Delay
2-12 Motor Temp Check
3 Inputs
3-1 Local/Remote
3-2 Comms in Remote
3-3 Input A Function
3-4 Input A Name
3-5 Input A Trip
3-6 Input A Trip Dly
3-7 Input A Initial Dly
3-8 Remote Reset Logic

7.5 Primary Motor Settings

NB!
Default settings are marked with *.
The parameters in Primary Motors Settings configure the soft starter to match the connected motor. These parameters describe the motor's operating
characteristics and allow the soft starter to model the motor's temperature.
4 Outputs
4-1 Relay A Function
4-2 Relay A On Delay
4-3 Relay A Off Delay
4-4 Relay B Function
4-5 Relay B On Delay
4-6 Relay B Off Delay
4-7 Relay C Function
4-8 Relay C On Delay
4-9 Relay C Off Delay
4-10 Low Current Flag
4-11 High Current FLag
4-12 Motor Temp Flag
4-13 Analog Output A
4-14 Analog A Scale
4-15 Analog A Max Adj
4-16 Analog A Min Adj
5 Start/Stop Timers
5-1 Auto-Start Type
5-2 Auto-Start Time
5-3 Auto-Stop Type
5-4 Auto-Stop Time
6 Auto-Reset
6-1 Auto-Reset Action
6-2 Maximum Resets
6-3 Reset Dly Grp A & B
6-4 Reset Delay Grp C
7 Secondary Mtr Set
7-1 Motor FLC-2
7-2 Lock Rotor Time-2
7-3 Start Mode-2
7-4 Current Limit-2
7-5 Initial Crnt-2
7-6 Start Ramp-2
7-7 Kickstart Lvl-2
7-8 Kickstart Time-2
7-9 Excess Strt Time-2
7-10 Stop Mode-2
MG.17.K2.02 - VLT ® is a registered Danfoss trademark
7-11 Stop Time-2
7-12 Adaptv Ctrl Gain-2
7-13 Adaptv Start Prof-2
7-14 Adaptv Stop Prof-2
7-15 Brake Torque-2
7-16 Brake Time-2
8 Display
8-1 Language
8-2 User Scrn Top L
8-3 User Scrn Top R
8-4 User Scrn Btm L
8-5 User Scrn Btm R
8-6 Graph Timebase
8-7 Graph Max Adj
8-8 Graph Min Adj
8-9 Mains Ref Volt
15 Restrict Paramtr
15-1 Access Code
15-2 Adjustment Lock
15-3 Emergency Run
15-4 Current Calibrat
15-5 Main Cont Time
15-6 Bypass Cont Time
15-7 Motor Connection
15-8 Jog Torque
16 Protection Action
16-1 Motor Overload
16-2 Current Imbalance
16-3 Undercurrent
16-4 Inst Overcurrent
16-5 Frequency
16-6 Heatsink Overtemp
16-7 Excess Start Time
16-8 Input A Trip
16-9 Motor Thermistor
16-10 Starter Comms
16-11 Network Comms
16-12 Battery/Clock
7 Programming
7
59