Instructions For The Installer - eka ekf 711 p Use And Instruction Manual

Electric Oven rev. 0 _____________________________________________________________EKF 711 P – EKF 664 P

4. 4. 4. 4. Instructions for the installer

Instructions for the installer Instructions for the installer Instructions for the installer
The following instructions are aimed at the qualified installer, to ensure that he carries out the
installation, adjustment and maintenance operations as correctly as possible and according to
current legal regulations. Any operation must be performed with electrical power cut to the
appliance. Before using the appliance, carefully remove the special adhesive film protecting the
parts in stainless steel. Do not leave any glue residues on the surfaces. If necessary, remove
them at once, with an appropriate solvent.
Positioning - Position the appliance perfectly horizontally on a table or similar support (the table Positioning
Positioning Positioning
or support must be at least 85 cm above the floor). Position it at a distance of not less than 10
cm from the side and rear walls, to enable natural ventilating air to circulate freely around it.
The appliance is ventilated through specific openings on the metal walls of the outer housing ,
and ensures efficiency and long-life. For this reason it is strictly forbidden to obstruct these
ventilation openings, even partially or for short periods. Failure to observe this specific
prohibition releases the manufacturer of the appliance from all responsibility and immediately prohibition releases the manufacturer of the appliance from all responsibility and immediately prohibition releases the manufacturer of the appliance from all responsibility and immediately prohibition releases the manufacturer of the appliance from all responsibility and immediately
voids any guarantee rights for the said appliance, because its constructive conformity has been voids any guarantee rights for the said appliance,
voids any guarantee rights for the said appliance, voids any guarantee rights for the said appliance,
voluntarily compromised. Furthermore, the appliance is not suitable for embedding and for
grouped positioning with other identical appliances.
Electrical connection - The appliance must be connected to the electrical mains according to Electrical connection
Electrical connection Electrical connection
current legal regulations. Before making the connection, make sure of the following:
- the voltage and frequency values of the power supply system match the values on the
"technical data" plate affixed on the appliance;
- the limiting valve and the system are able to support the appliance's load (see the
"technical data" plate);
- the power supply system has an adequate earth connection according to current legal the power supply system has an adequate earth connection according to current legal the power supply system has an adequate earth connection according to current legal the power supply system has an adequate earth connection according to current legal
regulations; regulations;
regulations; regulations;
- a omnipolar switch with minimum between-contacts aperture of the overvoltage
category III (4000 V), sized to the load and conforming to current legal regulations, is
fitted between the appliance and the mains in the direct connection to the mains;
- the omnipolar switch used for connection is easy to reach when the appliance is
installed;
- the yellow/green earth wire is not interrupted by the switch; the yellow/green e
the yellow/green e the yellow/green e
- the power supply, when the appliance is operating, must not deviate from the rated
voltage value by ±10%.
- make sure that after inserting the power supply cord into the terminal block it does not
come into contact with any of the cooking range's hot parts.
- if the supply cable is damaged then it must be replaced by the manufacturer or by your if the supply cable is damaged then it must be replaced by the manufacturer or by your
if the supply cable is damaged then it must be replaced by the manufacturer or by your if the supply cable is damaged then it must be replaced by the manufacturer or by your
technical support or by a qualified person to avoid any risk technical support or by a qualified person to avoid any risk technical support or by a qualified person to avoid any risk technical support or by a qualified person to avoid any risk
Connecting the power cable - To reach the power terminal board remove the left side of the Connecting the power cable Connecting the power cable Connecting the power cable
appliance. Loosen the cable-clamp on the back (at the bottom) of the appliance and pass the
cable through up to near to the terminal board. Locate the leads against the terminal board so
that the earth lead is the last to detach from its terminal in the event of reverse pulling. Connect
the 3 phase phase phase phase leads to the terminals marked "1" "2"
marked "4" "4" or "5" "4" "4" "5" "5" and the earth "5"
layout:
___________________________________________________________________________________________ page 5
arth wire is not interrupted by the switch;
arth wire is not interrupted by the switch; arth wire is not interrupted by the switch;
"1" "2" and "3" "1" "2" "1" "2"
earth lead to the terminal marked earth earth
Failure to observe this specific
Failure to observe this specific Failure to observe this specific
"3", the neutral "3" "3" neutral lead to the terminal neutral neutral
as shown in the following