Table of Contents
Related Manuals for eka EKF 464 TC
Summary of Contents for eka EKF 464 TC
- Page 1 ORIGINAL OPERATING AND INSTRUCTION MANUAL MODELS EKF 464 TC – EKF 511 TC rev. 5 TECNOEKA S.r.l. Via Marco Polo, n.11 - 35010 Borgoricco (Padova) Italy Tel. +39.049.9300344 – +39.049.5791479 Fax +39.049.5794387 www.tecnoeka.com E-mail: info@tecnoeka.com...
- Page 2 _________________________________ Borgoricco, 06/07/2016. Board Representative Signature (Lora Cristina) X:\Sgq\PRODOTTI\1 - FORNI\FORNO ELETTRICO\LEka\MANUALI D'USO - Forno Elettrico 40 60 90 - LEka\Lingua Inglese\NUOVA GAMMA EF\Instruction manual EKF 464 TC - EKF 511 TC - GB - rev. 5.doc page 2 _____________________________________________________________________________________________...
-
Page 3: Table Of Contents
Electronic convection oven rev. 5 _________________________________________MODELS EKF 464 TC – EKF 511 TC Contents Technical service General information Instructions for the installer Instructions for the user Settings menu Accessories menu Oven-user communication Cleaning Maintenance Possible faults Possible alarms Electrical diagrams... -
Page 4: Technical Service
TECNOEKA Srl ___________________________________________________________ operating and instruction manual 1. Technical service For periodic maintenance checks and repairs, contact your nearest Support Centre and only use original spare parts. Failure to comply with this provision shall forfeit the warranty right. 2. General information It is essential for this instruction manual to be stored together with the appliance for future referencing;... -
Page 5: Instructions For The Installer
Electronic convection oven rev. 5 _________________________________________MODELS EKF 464 TC – EKF 511 TC 2.1 Technical data plate (example) CERTIFICATION EKF 464 TC 8 kW 5214010500 SERIAL NUMBER 400V 3N 50/60 Hz IPX5 400V 3N 50/60 kPa 100 - 200 The “technical data”... - Page 6 TECNOEKA Srl ___________________________________________________________ operating and instruction manual 3.3 Unpacking the appliance Remove packaging before installation. It consists of a wooden pallet supporting the appliance and a cardboard casing protecting it. Ensure the appliance has not undergone any damage during transport; otherwise immediately alert your dealer and/or carrier. 3.4 Removal of the protecting film Before using the appliance accurately remove the special film protecting the stainless steel components, avoiding to leave glue residues on the surfaces;...
- Page 7 Electronic convection oven rev. 5 _________________________________________MODELS EKF 464 TC – EKF 511 TC the limiting valve and the system are able to withstand the appliance's load (see "technical data" plate); the power supply system is fitted with effective earthing connection according to the regulations in force;...
- Page 8 TECNOEKA Srl ___________________________________________________________ operating and instruction manual 3.8 Power supply cable connection Remove the back and left side of the appliance to access the power supply terminal board. Loosen the cable retainer at the rear (bottom) of the appliance (see Fig.1) and run the cable through it until reaching the terminal board.
- Page 9 Electronic convection oven rev. 5 _________________________________________MODELS EKF 464 TC – EKF 511 TC In any case, for reasons of compliance with health regulations in force, the piping connected to the drain pipe of the appliance must not be in direct contact with the drain point.
-
Page 10: Instructions For The User
TECNOEKA Srl ___________________________________________________________ operating and instruction manual 4. Instructions for the user 4.1 General information Use the appliance at room temperature between +5°C and +25°C. 35°C may be reached occasionally. The temperature of the appliance's external surfaces may exceed 60°C, only touch control elements. - Page 11 Electronic convection oven rev. 5 _________________________________________MODELS EKF 464 TC – EKF 511 TC 4.2 Control panel LCD DISPLAY INCREASE PARAMETER VALUE DECREASE PARAMETER VALUE CONFIRM PARAMETER VALUE STEP/PARAMETER SELECTION AIR FLOW SPEED SETTING "PRE-HEATING" SETTING GENERAL SETTINGS MENU PROGRAMMING ACCESSORIES...
-
Page 12: Manual Operation
Keep your finger on the “START/STOP” key for a few seconds and the display will show the screen with the “EKA” logo, DATE/TIME. After 5’’ the screen dissolves and the oven automatically readies for programming the cooking cycle: the “TIME”... - Page 13 Electronic convection oven rev. 5 _________________________________________MODELS EKF 464 TC – EKF 511 TC 4.3.2.2 Selection of cooking parameters The following parameters may be set for each step of the cooking cycle (up to 9 steps): 1. Cooking time 2. Cooking chamber temperature 3.
- Page 14 TECNOEKA Srl ___________________________________________________________ operating and instruction manual The PARAMETER SCREEN reads: “OFF” use the key to enable this option (the display then reads ”ON”) which is confirmed with the “SELECT” key; use the key to disable this option (the display reads “OFF” again) which is confirmed with the “SELECT”...
- Page 15 Electronic convection oven rev. 5 _________________________________________MODELS EKF 464 TC – EKF 511 TC When the OVERVIEW SCREEN shows the TEMPERATURE IN CHAMBER parameter and the CORE TEMPERATURE parameter , to go back to setting the TIME parameter - Use the “STEP”...
- Page 16 TECNOEKA Srl ___________________________________________________________ operating and instruction manual 4.3.3.4 “PREHEATING” setting (Overview screen) Use the key and the display shows the relevant PARAMETER SCREEN. Use the key (“ON”) to activate the function or the key (“OFF”) to deactivate it. In both cases use the “SELECT”...
- Page 17 Electronic convection oven rev. 5 _________________________________________MODELS EKF 464 TC – EKF 511 TC Touch the key “SELECT” to confirm the selection: “ST” is displayed in the overview screen in the direction of the icon indicating motor speed. Fan speed may be modified also while baking in “semi-static” mode.
- Page 18 TECNOEKA Srl ___________________________________________________________ operating and instruction manual The 30’’ “cooking completed” buzzer may be interrupted at any time by touching the “STEP” key or the “START/STOP” key. The OVERVIEW SCREEN of the cooking cycle just ended is displayed again. 4.3.6 Cooking cycle setting 4.3.6.1 Cooking cycle with time and temperature in chamber From "TIME"...
- Page 19 Electronic convection oven rev. 5 _________________________________________MODELS EKF 464 TC – EKF 511 TC From OVERVIEW SCREEN Touch key “STEP” to select the TIME parameter then touch keys to set the desired value. The value is automatically confirmed after 5”. Use the “START/STOP”...
- Page 20 TECNOEKA Srl ___________________________________________________________ operating and instruction manual From PARAMETER SCREEN “% HUMIDITY/STEAM” (optional function) After setting the value of the parameter “CORE TEMPERATURE”, use the “SELECT” key: the parameter screen “% HUMIDITY/STEAM” is displayed. Use the keys to set the desired value. Touch the “SELECT” key to confirm the set value.
- Page 21 Electronic convection oven rev. 5 _________________________________________MODELS EKF 464 TC – EKF 511 TC Important The “DELTA T” parameter makes it possible to maintain constant, throughout the cooking stage, the difference ( ) between the temperature inside the food (temperature detected by the needle-shaped thermal probe) and the temperature inside the cooking chamber.
- Page 22 The user is able to delete a program (recipe) set and stored in the “CHEF RECIPE BOOK” at any time. Use the key with symbol to bring up the “EKA RECIPE BOOK” screen. Touch the “STEP” key to select the word “CHEF” (word highlighted on dark background). Use the “SELECT”...
- Page 23 Electronic convection oven rev. 5 _________________________________________MODELS EKF 464 TC – EKF 511 TC 4.3.7.3 “Download” programs from oven (onto “USB pen drive”) With the oven's “USB port” the user is able to “download” into the “USB pen drive” the programs (recipes) stored in the “CHEF RECIPE BOOK”.
- Page 24 “EKA RECIPE BOOK” and the same cooking programs in the “CHEF RECIPE BOOK”, modifiable. By referencing these recipe books you are able to execute the recipes from the “EKA RECIPE BOOK” (see paragraph 4.3.7.7.1) or to run and/or modify the parameters of the cooking cycles from the “CHEF RECIPE BOOK”...
- Page 25 Electronic convection oven rev. 5 _________________________________________MODELS EKF 464 TC – EKF 511 TC 4.3.7.7.1 Using programs stored in the “EKA RECIPE BOOK” To use a program/recipe ( see paragraph 15 “RECIPE BOOK” ): Use the key with symbol to bring up the “EKA RECIPE BOOK” screen. Use the “SELECT”...
-
Page 26: Standard Functions
It lets you select the last ended cooking cycle: whether it has been executed in “manual” or programmed mode. Use the key to bring up the “EKA RECIPE BOOK” screen. Use the “STEP” key and select “LAST” (word highlighted on dark background). - Page 27 Electronic convection oven rev. 5 _________________________________________MODELS EKF 464 TC – EKF 511 TC 4.3.8.3 “HACCP” function The “HACCP” function has the purpose of recording the operative data of cooking cycles performed, constantly monitoring their progress. The “HACCP” data are recorded into a “USB pen drive” which must be connected into the suitable “USB port”...
- Page 28 TECNOEKA Srl ___________________________________________________________ operating and instruction manual START OF COOKING COOKING CORRECTLY ENDED COOKING INTERRUPTED WITH START/STOP KEY OR DUE TO AN ALARM ALARM: OPEN DOOR ALARM: THE CORE PROBE HAS BROKEN DOWN DURING COOKING ALARM: THE TEMPERATURE PROBE IS FAULTY ALARM: MOTOR ALARM: SAFETY THERMOSTAT ALARM: RESISTORS ARE NOT CONNECTED...
-
Page 29: Settings Menu
Electronic convection oven rev. 5 _________________________________________MODELS EKF 464 TC – EKF 511 TC 5 . Settings menu This function lets you view the various available settings. Use the key to bring up the “SETTINGS” screen. Use the “STEP” key to select the desired setting. -
Page 30: Oven-User Communication
TECNOEKA Srl ___________________________________________________________ operating and instruction manual Use the “STEP” key to choose the name (type) of accessory to be activated, in case it is already available and connected to the oven. Touch key “SELECT” to confirm the selection. If no choice is made, after 20” the overview screen of the cooking cycle is displayed automatically. - Page 31 Electronic convection oven rev. 5 _________________________________________MODELS EKF 464 TC – EKF 511 TC 8.2.2 Semi-automatic cleaning spray specific degreaser for stainless steel on the internal walls of the cooking chamber, on the side grilles, on the fan covers (do not spray onto the fans through the grille) and on the internal door glass;...
-
Page 32: Maintenance
TECNOEKA Srl ___________________________________________________________ operating and instruction manual 8.5 Door cleaning The internal glass of the cooking chamber door may be cleaned using the same type of degreaser used for manually cleaning the cooking chamber; otherwise, a normal (non toxic) glass cleaning product may be used. -
Page 33: Possible Faults
Electronic convection oven rev. 5 _________________________________________MODELS EKF 464 TC – EKF 511 TC 10 Possible faults Type of fault Cause of the fault Corrective action Non conforming connection to the power mains Check connection to the mains Control panel totally off... -
Page 34: Technical Support
TECNOEKA Srl ___________________________________________________________ operating and instruction manual 12 Wiring diagrams Power supply terminal board LED Bar Power Supply Unit B1-B2-B3-B4 Contactor coils LED Bar Relay coil Door microswitch Circular resistors Water solenoid valves Safety thermostat Cooking chamber probes Capacitors Food “core” probe Radial motorfans Microprocessor board Cooling motorfans... -
Page 35: Information To Users
Electronic convection oven rev. 5 _________________________________________MODELS EKF 464 TC – EKF 511 TC 14. Information to users Pursuant to Directive 2012/19/UE the crossed out bin symbol on the appliance indicates that at the end of its life the product must be collected separately from other waste. -
Page 36: The Warranty
TECNOEKA Srl ___________________________________________________________ operating and instruction manual 16. The Warranty Your appliance is covered by warranty. The seller will replace or repair (and his decision will be final), free of charge for the customer, only those parts that are defective due to a manufacturing fault on condition that, under penalty of forfeiture: ...