Table of Contents
Advertisement
_ Electric Ovens _ rev. 5 ________________________________________ KF 610 – KF 620 – KF 622 – KF 622 GRILL _
4. 4. 4. 4. Instructions for the installer
Instructions for the installer
Instructions for the installer
Instructions for the installer
The following instructions are aimed at the qualified installer, to ensure that he carries out
the installation, adjustment and maintenance operations as correctly as possible and according
to current legal regulations. Any operation must be performed with electrical power cut to the
appliance.
Before using the appliance, carefully remove the special adhesive film protecting the parts in
stainless steel. Do not leave any glue residues on the surfaces. If necessary, remove them at
once, with an appropriate solvent.
Fitting the feet
Fitting the feet
Fitting the feet
Fitting the feet - The feet are inside the appliance and must be secured on the four threaded
holes on the base. If necessary, the height of the feet can be adjusted by screwing or
unscrewing.
Positioning
Positioning
Positioning - Position the appliance perfectly horizontally on a table or similar support (the
Positioning
table or support must be at least 85 cm above the floor). Position it at a distance of not less
than 10 cm from the side and rear walls, to enable natural ventilating air to circulate freely
around it. The appliance is ventilated through specific openings on the metal walls of the outer
housing , and ensures efficiency and long-life. For this reason it is strictly forbidden to obstruct
these ventilation openings, even partially or for short periods. Failure to observe th
prohibition releases the manufacturer of the appliance from all responsibility and immediately
prohibition releases the manufacturer of the appliance from all responsibility and immediately
prohibition releases the manufacturer of the appliance from all responsibility and immediately
prohibition releases the manufacturer of the appliance from all responsibility and immediately
voids any guarantee rights for the said appliance, because its constructive conformity has been
voids any guarantee rights for the said appliance,
voids any guarantee rights for the said appliance,
voids any guarantee rights for the said appliance,
voluntarily compromised. Furthermore, the appliance is not suitable for embedding and for
grouped positioning with other identical appliances.
Electrical connection
Electrical connection - The appliance must be connected to the electrical mains according to
Electrical connection
Electrical connection
current legal regulations. Before making the connection, make sure of the following:
-
the voltage and frequency values of the power supply system match the values on the
"technical data" plate affixed on the appliance;
-
the limiting valve and the system are able to support the appliance's load (see the
"technical data" plate);
-
th th th the power supply system has an adequate earth connection according to current legal
e power supply system has an adequate earth connection according to current legal
e power supply system has an adequate earth connection according to current legal
e power supply system has an adequate earth connection according to current legal
regulations;
regulations;
regulations;
regulations;
-
a single-pole switch with minimum between-contacts aperture of 3 mm, sized to the
load and conforming to current legal regulations, is fitted between the appliance and the
mains in the direct connection to the mains;
-
the single-pole switch used for connection is easy to reach when the appliance is
installed;
-
the yellow/green earth wire is not interrupted by the switch;
the yellow/green earth wire is not interrupted by the switch;
the yellow/green earth wire is not interrupted by the switch;
the yellow/green earth wire is not interrupted by the switch;
-
the power supply, when the appliance is operating, must not deviate from the rated
voltage value by ±10%;
-
make sure that after inserting the power supply cord into the terminal block it does not
come into contact with any of the cooking range's hot parts.
Connection of power cable
Connection of power cable - The terminal board is on the rear panel of the appliance. Open
Connection of power cable
Connection of power cable
the terminal board cover by obtaining leverage with a screwdriver on the two side fins. Loosen
the cable gripper screw and allow the cable to pass through it. Arrange the conductors so that
the earth conductor is the last to detach from its terminal if the cable goes into a state of faulty
traction. Connect the phase conductor to the terminal marked with the letter "L", the neutral
conductor to the terminal marked with the letter "N" and the earth conductor to the terminal
marked with the symbol
board cover. The appliance must be connected to an equipotential system
must first be checked according to current legal regulations. This connection must be made
between different appliances by using the appropriate terminal marked with the symbol
equipotential conductor must have a minimum diameter of 10 mm
is at the rear of the appliance.
_________________________________________________________________________________________ page 5 _
. Tighten the ring-nut of the cable gripper and close the terminal
Failure to observe this specific
Failure to observe th
Failure to observe th
equipotential system whose efficiency
equipotential system
equipotential system
2
The equipotential terminal
is specific
is specific
is specific
. The
Hide quick links:
Advertisement
Table of Contents
