Fixing For Operation; Limits Regarding The Workpiece Size; General Instructions For Use - stayer SC300W Operating Instructions Manual

2.Place the new cutting disk in such a manner that
the direction of the stationary lower guard
coincides with the arrow engraved in the
disk and with the direction of the disk teeth
as such.
3.Place the flange 17, washed 19 and the Allen
screw 18 making sure the perfect fitting of
the whole group.
4.Block flange 17 with the flange wrench as
delivered together with the equipment.
5.Tighten screw 18 counter clockwise by means of
the tubular key as delivered together with
the equipment.
6.Place tiltable guard 6 in its original protective
position by pulling it downwards.
7.Revise the operation simulating a cutting
operation with no load.

10.Fixing for operation

Whenever possible, the workpiece must be fixed in
such a manner that the hand does not intervene.
During the cut, keep the workpiece fixed to the
support. All models are prepared for mounting
horizontal and vertical clamps allowing fastening
the profile in a safe manner.
To avoid deformations of the workpieces during
fixing thereof, the use of wooden profiles being
easily applicable to the movable jaws of the clamps
is advised. Clamps can be easily extracted and
leave the working surface totally clear.
For cutting long workpieces under safe conditions it
is essential to hold them with additional supports.
11.Limits regarding the workpiece
size
Limits for all models as included in the
present manual
Information!
Models SC310W, SC390W and SLL390W lack an
upper table so that the limit regarding the workpiece
size for cutting operations on the upper table is not
applicable to this model.
ENGLISH
45
Model
SC300W SC310W SC311W SCE311W
185x85 163x95
90º
45º 125x85 112x95
Inclined
180x60 163x65
45º
65x65
Composed
100x65
45º- 45º
95x15
Straight cut
60x105 40x103
0º
Straight cut
40x105 40x103
right 45º
Straight cut
40x105 25x103
left 45º
Diameter
120 95
PVC tube
0-53 No aplica
Table

12.General instructions for use

Warning!
1.Do NOT use the machine if it is in a bad condition
or lacks parts including the prescribed
upper guards (the illustrations of the
present manual may be used as an
orientative guide). Unplug it, remove it from
the working area and immediately send it to
an authorized technical service.
2.Know and comply with all safety measures before
you start the machine.
Starting and stopping the machine
IMAGES
Information:
1.The machine is provided with a locking button 2
for starting allowing the motor to run without
needing to push switch 1 permanently.
2.The equipment is provided with a safety module
protecting it against unexpected starts. If,
whilst the machine is running, the supply of
electrical power should cease, the machine
will not start after reestablishment thereof.
To release the protection push the button 2
twice.
3.Except for SCE311W all models are single
speed.
45
SC390W SC391W
SLL390W SLL391W
163x95 163x95 163x80 163x80
112x95 112x95 112x80 112x80
163x65 163x65 163x65 163x65
65x65 65x65 65x65 65x65
95x15 95x15 95x15 95x15
40x103 40x103 40x100 40x100
40x103 40x103 32x100 32x95
25x103 25x103 25x100 25x100
95 9 80
0-52 0-52 No aplica 0-52
N M
SC3000W
163x80
112x80
163x65
65x65
95x15
40x100
32x100
25x100
80 80
0-52