Changing Tools; Fixing For Operation; Limits Regarding The Workpiece Size - stayer SC 210 BW Operating Instructions Manual

When lowering the head (F) make sure that the tab on
the guard (2) fits into the lower part of the head, thus
engaging the upper table safety system button (16), and
is not bent or wedged elsewhere.
5 Press the lower locking pin (5) to lock the tool in the down
position.
Adjusting the vertical mitre angle to 90º/45º
Checking
1
Release vertical adjustment of the head by loosening
control element or nut 8.
2
Move head to the right stopper (90º/45º).
Y
3
Check the angle by means of a duly calibrated angle
chart or a goniometer (minimum precision +- 5º) applying
one of the surfaces thereof on cutting table and the other
on cutting disk.
4
Should the side of the angle chart not adjust exactly to
the disk or if the direct measurement of the goniometer
reached a deviation of more than +- 20º, proceed to
adjusting.
Adjusting
1 Place a goniometer (minimum precision +- 5º) applying
Y
one of its sides on cutting table and the other on cutting
disk.
2 Act on adjusting screw 7 until obtaining a measurement
of 90º/45º.
Adjusting the riving knife
The riving knife is the piece that holds the blade guard on the
upper table (15) in place.
Its function is to separate and divert the debris produced
when cutting on the upper table so that the debris does not
impact the user.
To check and adjust it, lock your machine in the down position
Y
and check the alignment of the knife with the blade and
ensure that the distance between the blade teeth and the
knife surface is 2 mm.
If not, adjust it using the knobs that hold the knife in place
(10).Removing the cutting blade

CHANGING TOOLS

8.
Attention!
This operation must be carried out with the machine
unplugged and with the disk still. Use protective gloves.
- Use obligatorily disk according to normative EN 847-1
- Use obligatorily the regulatory push stick and save it away
if not use it.
- Use of fast steel disks prohibited (HSS)
- Use of defective or deformed prohibited
- Replace the table insert when worn
Removing the cutting blade
1 1. Lock the head in the up position by turning the head
upwards until it stops.
2 Remove the casing lock screw (11).
3 Pull up on the guard to remove it.
4 Keep the cutting blade still by pressing it against a wood
block and loosen the blade screw by turning it clockwise.
5 Remove the blade to be replaced
Changing the cutting blade
1 Carefully clean all sawdust and dirt from the brackets,
X
X
X
ENGLISH
16
flanges and inside of the guards.
2 Place the new cutting blade so that the direction of
the arrow on the front of the casing matches the arrow
engraved on the blade and the tilt of the blade's teeth.
3 Attach the flange and its screw
4
Turn the screw counter-clockwise while the blade is kept
still using a wood block.
5
Return the guard to its original protective position by
pulling it downward. Once the guard is set, put the locking
screw back in its place (11). Once in place, make sure
that the protective casing only opens when the head is
lowered.
6
Check the correct operation by simulating a cutting
operation at idle speed.

FIXING FOR OPERATION

9.
Whenever possible, the workpiece must be fixed in such a
manner that the hand does not intervene.
During the cut, keep the workpiece fixed to the support. ALL
MACHINES ARE PREPARED FOR MOUNTING CLAMPS
ALLOWING FASTENING THE PROFILE IN A SAFE
MANNER.
To avoid deformations of the workpieces during fixing thereof,
the use of wooden profiles being easily applicable to the
movable jaws of the clamps is advised. Clamps can be easily
extracted and leave the working surface totally clear.
For cutting long workpieces under safe conditions it is
essential to hold them with additional supports.

LIMITS REGARDING THE WORKPIECE SIZE

10.
Limits for all models as included in the present manual on
page 3
GENERAL INSTRUCTIONS FOR USE
11.
Warning!
1 Do NOT use the machine if it is in a bad condition or
lacks parts including the prescribed upper guards (the
illustrations of the present manual may be used as an
orientative guide). Unplug it, remove it from the working
area and immediately send it to an authorized technical
service.
2 Know and comply with all safety measures before you
start the machine.
- Obligatory used of aspiration particle system when cutting
the wood.
Starting and stopping the machine
Information
1 The tool has a single start-up/shut-off interlocking
mechanism.
This mechanism will not work when the machine is set up as
a cutting table if the lower protective casing (2) is not correctly
in place with the safety lock button (16) engaged.
2 The equipment is provided with a safety module protecting
it against unexpected starts. If, whilst the machine is
running, the supply of electrical power should cease, the
machine will not start after reestablishment thereof. To
release the protection push the starting button 2 twice.
Warnings!
1
Never leave running machine unattended.
2
Never start the machine with locked disk and, before
starting a cut, always wait until the cutting disk has
reached its maximum speed.
3
Before stopping the machine the disk must be clear and
be rotating freely.
Start-up/shut-down
Switches (13)
Start-up: Press the green button I.
Shut-off: Press the red button O
16
(with automatic interlocking).