Stokke XPLORY User Manual page 16

16
eN
Folding. (1-3) SEAT Dissasembly (7)
STOKKE® XPLORY® back wheels: Press the service handles in on each side
1. All four wheels must touch the of the seat simultaneously and lift the
ground. Do NOT start by lifting the seat off the seat arms. The child should
unit/back wheels to fold them in. not be in the seat during this procedure.
(See Figure 1).
2. Push bottom part (B) of the han-
Adjusting the seat height (8)
dle on the spine UP, then – while Release the handle (F), move the seat
holding this – press the top part (A) arm to the desired height and lock the
of handle in – and at the same time – handle by pressing it back into place.
lift this handle UP. (See Figure 2) Please make sure that you always hold
3. Now, push with your foot on the the seat arm by the centre sleeve that
lower part of footpeddle (C) located
attaches it to the centre column, the seat
at top of the arch. Continue to push arm will then be easy to move. Adjustable
with your foot, while pulling the height is 50 to 70 cm from the bottom of
steering handle towards you. (See the seat.
Figure 3)
Mounting and adjusting the foot rest
Unfolding (2) (9)
STOKKE® XPLORY® back wheels: Push the footrest up the tracks. Check
Pull the bottom part (B) of the han- to make sure that the footrest is locked
dle on the spine UP, then – while in position. Dismounting and adjusting the
holding this in position – press the footrest downwards is done by pushing
top part (A) of the handle in – and at
the handles (J) on both sides up and mov-
the same time – lift the main steering ing the footrest in the tracks. To provide
handle UP and forward. The legs will the best comfort possible, adjust the
release. (See Figure 2) footrest to support your child's feet.
If the unit's wheels are locked in
a folded position and difficult to Seat rail (10)
release, give the foot-peddle a slight
Release seat rail on both sides and pull
push – with either your hand or foot the rail up. Insert the seat rail into place.
- while you unfold the back wheels. A click will be heard when the rail is
placed correctly. Warning! Do not use the
Adjusting the handle, height and rail for carrying.
angle (4)
Lift the trigger (D) and hold it up Brake (11)
while you adjust the handle to the Always remember to engage the brakes
desired height. The handle height can when you park the stroller. Do this by
be adjusted to any position in a range pressing the lower part of the brake
between 67 and 116 cm/26,4 and pedal. To release the brake, press the
45,7 inch. The handle can be adjusted
upper part of the brake pedal.
to 4 different angles by pressing the
trigger (E) down and rotating the Removing and attaching the back
handle. wheels (12)
Release the locking device and pull the
Seat Assembly (5) wheel off the axle. To attach push the
Push the seat down on the seat arm wheel onto the axle until you hear a click.
until a click is heard on each side. Check to make sure that the wheel is
The seat may be mounted in a posi- locked on to the axle.
tion facing forwards or backwards.
Check that the seat is properly Use on stairs (13)
mounted on the seat arms by
Stokke Xplory's unique design enables
ensuring that the indicators found on it to negotate obstacles such as thresh-
each side of the seat have changed olds and kerbs with ease. Stokke Xplory
colour from red to green. is especially easy to transport up/down
stairs using the two-wheel
Adjusting the seat angle (6) function. The child must not be sitting
The seat angle is adjusted by means
in the stroller while it is going up/down
of the handle (G) on the seat arm. stairs because transporting a child in a
Note! Always keep your hand on the stroller on stairs is generally dangerous.
seat when you adjust the angle. The
seat has 3 positions facing back-
wards, and 2 positions facing for-
ward.
WARNING!
Never assemble, remove or turn the
seat while your child is in it.
STOKKe XPLORY
® ®
Baby insert (14)
To ensure the best possible sitting
comfort for your child make sure that
the depth of the seat corresponds to
the length of the child's thigh. The
edge of the seat should fit to the back
of the child's knee. The padded baby
insert is attached by putting the safety
harness through the opening that best
fits the child's shoulder height. The
baby insert is recommended up to the
age of about 15 months.
Assemble hood on seat (15)
Position and push the hood plastic
fasteners in on each side of the seat.
Attach the hood to the seat fabric with
the zipper. Attach the push buttons on
each side.
Dismounting hood from seat (16)
Unbutton on each side of the hood.
Unzip to release the hood. Release
plastic fasteners from seat by pressing
the two taps on the inside of the seat.
Use both tombs and press.
Hood visor (17)
Attach and detach the visor from the
hood with the zip. Fold in and out.
Ventilation in hot weather (18)
Unzip the zip on the hood. Fold the
cover over the edge.
Adjusting the harness (19)
Your child should always use the
harness. Tighten the harness straps
so that the harness fits your child.
The harness is opened by pressing the
release mechanisms together. As the
child grows, adjust the harness
fasteners at the back so that they
correspond to the child's
shoulder height, see table. Thread the
strap through the fabric parts again.
STOKKE is not responsible if you
choose to use a harness other than
the one supplied! Nonetheless there
are D-rings on the waist belt for fitting
your own harness.
WARNING
Always use the crotch strap in
combination with the waist belt
Disassembling the fabric Assembling the fabric components after
components for washing: washing:
Disassembling the hood (20) Assembling the Seat cover (25)
Unzip to release the hood. Unbutton Insert the rails on the seat cover into
on each side of the hood. Pull up the
the slot on each side. Pull the seat cover
fabric on the side and the front to down. Position the harness. Crotch, waist
reveal the hood fastener. Press the and shoulder straps. Make sure that
notch on the hood fastener and pull shoulder straps
up the hood. Repeat at the other side. correspond to the child's shoulder height.
Remove the main rib before washing. Fasten the orange tag on each side of the
bottom rear of the back. Conceal the end
Disassembling the back cover (21) of the orange tag in the seat. Pull the fab-
Loosen the fabric from the push ric over the back.
buttons on each side and from the two
in front. Pull the fabric off the Velcro. Assembling the fabric on the seat guard
(26)
Disassembling the fabric on the seat Release the rib by pressing a thin pin or
guard (22) screwdriver into the little hole on each
Release the rib by pressing a thin pin side. Fasten the beginning of the zipper
or screwdriver into the little hole on around the bar with Velcro facing out.
each side. Open textile tab and unzip. Make sure that the tap goes through the
Loosen the fabric from the hook on fabric. Pull up the zip with tap through
both side of the rib. center and end. Fasten the rib by pressing
it into place.
Disassembling Seat rail cover Note! The rib can be mounted wrong!
Remove by pulling off.
Assembling the back cover (27)
Disassembling Harness covering Line up the center mark on the fabric to
Remove by pulling off. the corresponding center mark on the
seat guard. Attach the cover edge-to-
Disassembling Seat cover (23) edge on the Velcro. Attach the cover with
Loosen the orange tag on each side of the push buttons, 2 on each side, and with
the bottom rear of the back. Remove
the two on each side of the front.
the safety harness. Gently pull the
seat fabric up until it is completely off. Assembling the hood (28)
Insert the main rib after washing. Make
sure the notch on the main rib is facing
MAINTENANCE – WASHING front. Insert the main rib into both sides
INSTRUCTIONS of the hood fastener. A click will be heard
when the rib is placed correctly. Fasten
the hood with the push buttons on each
Hard parts
The stroller should be cleaned using side. Zip the hood onto the seat fabric.
a mild mixture of soap and water.
Make sure that any sand/mud/grit is Assembling the harness covering
removed prior to cleaning. No part of Enter the harness covering with the soft
side facing the child.
the stroller is to be lubricated. If any
function of the stroller is not working
properly, contact your Assembling the seat rail cover
nearest STOKKE retailer. Enter the cover by pulling it on.
Textiles must be washed separately
Basic mosquito net (29)
(24) Pull the mosquito net over the handle and
• When washing the baby insert, the footrest. Pull the mosquito net over
please remove the inside cushion the main rib of the hood. Snap on the
before washing the cover.
mosquito net using the push
• Remove the ribs before washing
buttons on each side. Pull the net until
the canopy. Release the main rib by the seat is completely covered. Pull up
pressing, e.g., a screwdriver into the zippers on each side of the central
the small holes in the canopy bar.
fasteners. Afterwards, thread all
the ribs out of the fabric.
Basic rain cover(30)
Pull the rain cover over the handle and
the footrest. Pull the rain cover over the
hood. Fasten using the Velcro around the
central bar and footrest. Pull up the
zippers on each side of the central bar.
STOKKe XPLORY
® ®
Basic shopping bag(31)
Place the shopping bag on the board.
Fasten around the central bar using
the attached hook.
Changing bag
Attach the changing bag to the seat
arm.
Stokke® Warranty card / Product
registration card:
See description of where to find the
products serial number/date clock on
your product. Use this information
when filling out the Stokke warranty
card / Product registration card. We
recommend that you fill in this
information at www.stokke.com.
17