Oki Teriostar LP-1030 User Manual page 133

In some cases micro-vectors may be printed clearly only with the parameters below:
z
Line End to Round; and
Line Join to Round
When the Micro-Vector Rounding is set to On, the micro-vector is processed with the
settings below:
Line End to Round; and
Line Join to Round
so that the micro-vector is printed clearly.
n
Pen N
z
Width (mm)
The parameter specifies the Printer's pen width. When it is set to 0.00, the Printer
prints lines with a 1-dot width.
<Parameter by entering numbers>
0.00 to 16.00
Specified Values
0.00 to 0.06 mm (0.0000 to 0.0024 inches)
0.07 to 0. 1 0 mm (0.0027 to 0.0039 inches)
0. 1 1 to 0. 1 4 mm (0.0043 to 0.0055 inches)
0. 1 5 to 0. 1 9 mm (0.0059 to 0.0075 inches)
0.20 to 0.23 mm (0.0079 to 0.0091 inches)
0.24 to 0.27 mm (0.0094 to 0.0106 inches)
0.28 to 0.31 mm (0.0110 to 0.0122 inches)
0.32 to 0.35 mm (0.0126 to 0.0138 inches)
0.36 to 0.40 mm (0.0142 to 0.0157 inches)
0.41 to 0.44 mm (0.0161 to 0.0173 inches)
0.45 to 0.48 mm (0.0177 to 0.0189 inches)
0.49 to 0.52 mm (0.0193 to 0.0205 inches)
z
Density (%)
Sets the density of the printer's pens.
<Parameter by entering numbers>
0 to 100
T
Default values:
Pen 0 = 0.20 mm (0.008 inches)* Pen 1 = 0.30 mm (0.012 inches)
Pen 2 = 0.40 mm (0.016 inches)
Pen 4 = 0.60 mm (0.024 inches)
Pen 6 = 0.80 mm (0.031 inches)
Pen 8 = 1.00 mm (0.039 inches)
* HP-GL only
Pen 15 = 1.00 mm (0.039 inches) *For HP-GL
Pen 32 = 1.00 mm (0.039 inches) *For D-SCAN
No. of Dots Specified Values
1 0.53 to 0.57 mm (0.0209 to 0.0224 inches)
2 0.58 to 0.61 mm (0.0228 to 0.0240 inches)
3 0.62 to 0.65 mm (0.0244 to 0.0256 inches)
4 0.66 to 0.69 mm (0.0260 to 0.0272 inches)
5 0.70 to 0.74 mm (0.0276 to 0.0291 inches)
6 0.75 to 0.78 mm (0.0295 to 0.0307 inches)
7 0.79 to 0.82 mm (0.0311 to 0.0323 inches)
8 0.83 to 0.86 mm (0.0327 to 0.0339 inches)
9 0.87 to 0.91 mm (0.0343 to 0.0358 inches)
10 0.92 to 0.95 mm (0.0362 to 0.0374 inches)
11 0.96 to 0.99 mm (0.0378 to 0.0390 inches)
12 1.00 to 1.03 mm (0.0394 to 0.0406 inches)
Default values:
Pen 0 = 0, Pens 1 to 15 (32) = 100
LP-1030/LP-1030-MF User's Manual for Basic Printer Operation
Setup Items in PDL Settings Menu
Pen 3 = 0.50 mm (0.020 inches)
Pen 5 = 0.70 mm (0.028 inches)
Pen 7 = 0.90 mm (0.035 inches)
Pen 9 = 1.00 mm (0.039 inches)
No. of Dots
Chapter
1
Chapter
2
Chapter
3
Chapter
4
Chapter
5
13
14
15
16
17
18
19
20
21
22
23
24
133