Vr Information Setting; How To Change The Modulation Mode - Ko Propo EX-2 Instruction Manual

● VR information setting
Adjust the steering and throttle resistance
information. ※ Please perform the VR information
configuration to calibrate your system.
○ When using EX-2 for the first time.
○ When changing a steering unit for a different
product or when putting it back together.
○ When changing a grip unit for a different product
or when putting it back together.
○ When using and confusion has occurred in the
positional information.
1.Select [FUNCTION] on the initial screen and push
the ENTER key.
2.Select [SYSTEM] on the function screen and push
the ENTER key.
3.Select [VR INFO] on the system screen and push
the ENTER key.
4.Move the wheel slowly to the full left and right lock
(numbers will change as the steering is moved) and
release the wheel back to neutral.
5.Move the trigger slowly to the full throttle and full
brake positions (numbers will change as the
throttle is moved) and release the trigger back to
neutral.
6.Then select YES (press ENTER) to adjust and save
the settings.
3.Example before setting
VR INFOMATION VRｲﾝﾌｫﾒｰｼｮﾝ
ﾋﾀﾞﾘ
ST- LEFT
ｾﾝﾀｰ
NUT
ﾐｷﾞ
RIGHT
ｾﾞﾝｼﾝ
TH- HI
ｾﾝﾀｰ
NUT
ﾌﾞﾚｰｷ
LOW
4,5, Move slowly to full stroke, then release.
Left MAX Right MAX
6, Small window [Yes] comes active.
VR INFOMATION VRｲﾝﾌｫﾒｰｼｮﾝ
ﾋﾀﾞﾘ
ST- LEFT
ｾﾝﾀｰ
NUT
ﾐｷﾞ
RIGHT
ｾﾞﾝｼﾝ
TH- HI
ｾﾝﾀｰ
NUT
ﾌﾞﾚｰｷ
LOW
※ When operating the VR INFORMATION and
pressing the BACK key will cancel the operation.
2204
2198
2
2194
OK?
2078
YES
2075
2072
Hold
Hold
Full Throttle
Full Brake
3949
2198 2
487
OK?
3313
YES
2075
1463
● How to change the Modulation mode
EX-2 has two Modulation modes.
※ When disassembling the Xpansion unit, this
operation is the same.
《Functions》
● General RC models FHSS mode： LED Solid
Operating the general receivers such as KR-211FH/KR-
241FH Only receivers using FHSS will work.
The receiver of other methods (DSSS/27/40MHz)
do not work.
● Mini-Z MHS mode ：LED Flashing slowly
Operating Kyosho Mini-Z MHS mode. (MR-03 VE
PRO)
※ Functions that are in Mini-Z will be lit up at initial
screen.
Only MiniZ using MHS will work. Does not work with
ASF, FHS, general RC cars.
① Turn off EX-2 switch.
② Push the ET1 lever to the left and power on.
③ Hold ET1 lever until the buzzer sounds and the
LED of EX-2 turns on (approximately two seconds).
PowerON
If the pilot LED is blinking fast, this is a warning
that the battery voltage is low. Please change to
new batteries or for a battery pack which has been
charged.
Model selection changes and modulation mode
changes are not linked.
19
ET1
A p p r o x i m a t e l y t w o
seconds, LED turns on.