1. Manuals
  2. Brands
  3. Ko Propo Manuals
  4. Remote Control
  5. EX-10 HELIOS
  6. Instruction manual

Ko Propo EX-10 HELIOS Instruction Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Advertisement

Table of Contents
loading

Related Manuals for Ko Propo EX-10 HELIOS

Summary of Contents for Ko Propo EX-10 HELIOS

  • Page 3: Read First

    IRST Read First Thank you for purchasing the EX-10 Helios. Read this manual carefully in order to obtain maximum performance from the unit. Keep this manual handy. How to fi nd information in this manual Please understand the basic uses of "How to use the transmitter".

  • Page 4: Table Of Contents

    ONTENTS Read first 04 05 Contents 06 07 08 Notes on safe usage Usage of the transmitter Names of parts of the transmitter LCD Screen table Main menu LCD Screen table F u n c t i o n m e n u 12 13 How to insert batteries and such How to use transmitter...

  • Page 5: Contents 04

    ONTENTS Function Menu Model select ET Position auto display Sub trim A.B.S (Acrive Brake System) 35 36 Throttle speed 37 38 Throttle punch Throttle curve Throttle brake Throttle high point Throttle preset Throttle acceleration 44 45 46 47 Steering speed Steering punch Steering curve Steering balance...
  • Page 6 Meaning of picture indications Warning Meaning of picture indications Be certain to use only KO Propo genuine crystal sets (transmitter and receiver). Warning! Other crystals may vary in frequency, which could lead to misoperation or loss of control.
  • Page 7 Be careful not to reverse the polarity of the transmitter and the receiver. Caution! Reverse polarity could damage the unit. Be sure to use genuine KO Propo products e.g. transmitter, receiver, ESC and Caution! other optional parts. We cannot assume any responsibility for the use of other companies’...
  • Page 8 Never incinerate the batteries. Danger! It is very dangerous because they may explode. Be sure to use KO Propo charger and to use correct charging current. (1A) Danger! Avoid over charging the battery. Over charging does not only damage the battery, but can cause excess heat build-up and possibly fire, which results in serious accidents.

  • Page 9: Names Of Parts Of The Transmitter

    AMES OF ARTS OF THE RANSMITTER Antenna Throttle A.B.S. indicator Throttle acceleration indicator Hook ET1 Lever Throttle speed indicator (-) Minus key Steering Wheel (+)Plus key Jog Dial 12x4 LCD Display Et3 Lever Enter Key Power indicator ET2 Lever Back key Power Switch Mode Change Switch Throttle trigger...

  • Page 10: Change Menu

    CREEN ABLE These screens are displayed when the main menu is opened. Please see each reference page about a detailed operation method after each screen is opened. Initial screen Plus Key Minus Key Jog Dial Enter Key Change menu Back Key Add menu The menu is displayed when ’Enter’...
  • Page 11 CREEN ABLE UNCTION These screens are displayed when the function menu is opened. Please see each reference page about a detailed operation method, after each screen is opened The function menu opens when Jog Dial or (+), (-) keys are operated Model Select ET Position from an initial screen.
  • Page 12 Please attach included sponge to the battery lid when the battery pack is used. About Charging (only for battery packs) Connect AC Mains charger or DC 12V charger (KO Propo products) as shown in figure. The charging time from flat condition is 14-16 hrs for AC Mains charger.
  • Page 13 When changing the crystals, be sure to use genuine FM-type transceiver crystals from KO Propo. Crystals from other manufacturers may operate at slightly different frequencies, resulting in loss of control. Only the RF Module for EX-10 Helios can be used. DRAFT...
  • Page 14 How to Use Transmitter-1 Preparation Insert dry cells or battery pack into the transmitter (P12) Be sure to charge battery pack before use. advice The battery will last long if crystal is pulled out or the RF module is detached when only the transmitter is operated. Moreover, when only the transmitter is operated when the management of the band is done in the course etc.
  • Page 15 How to Use Transmitter-2 Operation concerning memory. Reset a specific model memory to factory default setting. Select MEM.RESET from function menu and press enter. (Current model memory will be initialized.) Reference page Transferring model memory setting to other model memory. Select MODEL.COPY from function menu and press enter.
  • Page 16 SCREEN BOUT THE OPERATION OF THE n this machine, assume most settings to be an operation system thirdly, that is, Jogdial and the "Enter", "Back" key possible to enable an intuitive operation. Moreover, the change menu system that can efficiently use it with more set screen is newly adopted. Name of key Names on Initial Screen Plus Key...
  • Page 17 Change Manu In this unit, to use a lot of functions, Change Menu System is developed, and installed newly. This is the one that it is made to be able to do by quickly calling practicing more operation by switching Menu List that registers only the function to often use. About Change Menu By registering the content squeezed to CUSTOM1 or CUSTOM2 from a lot of function menu items, the switch is ..function item..
  • Page 18 Indicator warning About the display of each indicator. Throttle Speed Indicator Throttle A.B.S Indicator Throttle Acceleration When Throttle Speed (P37) is effective, it Indicator flashes. Moreover, the function of On/Off of Throttle Speed Throttle Speed is allocated in ET and the button, Indicator it flashes too.
  • Page 19 Movement mode (Responce mode) This Unit can select from 3 mode. to change the mode adjust the switch below of the RF module. and adjust the channel select in function mode. DRAFT...
  • Page 20 DRAFT...
  • Page 21 DRAFT...
  • Page 22 DRAFT...
  • Page 23 DRAFT...
  • Page 24 DRAFT...
  • Page 25 Response Mode Compatibility Table Response Mode Compatibility Table Compatible Advanced High Normal Super High Speed Incompatible Speed Receiver KR-297FZ (Discontinued) KR-301F KR-302F Analog Servo PS-401 PS-712FET PS-713FET PS-2173FET PS-2174FET PS-2113FET Digital Servo PDS-947FET PDS-2123FET PDS-2143FET PDS-2144FET PDS-2343FET PDS-2344FET EZ-1000 KSC-1000FR KSC-1100FR KSC-1200F VFS-2000...
  • Page 26 Main menu (1) Back Key Back Key Enter Key Enter Key JogDial JogDial It is the menu displayed when "Enter" is pushed from the initial screen. +/- Key +/- Key Reset Reset Change menu system The first screen of the main menu becomes a selection of the change menu system.

Table of Contents