5Way（5Way; Analog (Analog Mixing Menu); Gyro (Gyro Mixing Menu) - Ko Propo EX-2 Instruction Manual

3・4CH 3・4ch Menu
▶ 5WAY MODE
Modify the 5-interval output settings.
【Example】
May be used for gear changing operations or when
you wish to set a 5-interval control scheme for the
servo.
3CH MODE : 5WAY
START : POS1
KEY : ET3
SET
+
【Setting Range】
START：POS 1、POS 2、POS 3、POS 4、POS 5
Sets the starting position.
KEY：OFF、ET1 〜 5、BT1（Default：OFF）
Assigns a key to use for switching positions.
POS 1：-100 〜 100（Default：-100）
Sets Position 1's output position.
POS 2：-100 〜 100（Default：-50）
Sets Position 2's output position.
POS 3：-100 〜 100（Default：0）
Sets Position 3's output position.
POS 4：-100 〜 100（Default：50）
Sets Position 4's output position.
POS 5：-100 〜 100（Default：100）
Sets Position 5's output position.
▶ ANALOG MODE
These settings are to enable continuous output for
channels 3 or 4.
3CH MODE : ANALOG
KEY : ET3
REVERSE : NORM
STEP : 5
+
【Setting Range】
KEY：OFF、ET1 〜 5、BT1（Default：OFF）
Assigns a key to use for switching positions.
REVERSE：NOR
（通常）
Sets operation direction.
STEP：1 〜 25（Default：5）
Sets the amount of change for the operation.
POS1 : -100
POS2 : - 50
POS3 : 0
POS4 : 50
POS5 : 100
（Default：POS 3）
LOW : -100
CEN : 0
HIGH : 100
、REV （Default：NORM）
（逆向き）
LOW
（Low Position）
Sets the lowest value for the operation range.
CEN
（Center Position）
Sets the neutral position for the operation range.
HIGH
（High Position）
Sets the highest value for the operation range.
【How to Use Analog Settings】
Low Position Side:：
Between LOW and CEN are 100 steps within which the
intervals can be adjusted.
High Position Side:：
Between CEN and HIGH are 100 steps within which the
intervals can be adjusted.
ー
Example）When STEP value is 2
When LOW side is set to 5 intervals.
When HIGH side is set to 4 intervals.
High Position
Maximum
High Angle
P
Center position is the staring position.
Low/High positions cannot be exceeded. Operations
P
which try to do so will stop just before the Low/High
positions.
▶ GYRO MODE
This function modifies the setting for using gyro receiver.
【Example】
When using KR-212FHG Gyro receiver, this function
allows for an easy setting.
【How to set Gyro mode】
GYRO is configurated to channels 3/4 control modes.
ET3 : 3ch control （Steering gyro gain control)
ET5 : 4ch control (Throttle gyro gain control)
Adjust it to moderate gyro gain while running.
Specification of channel 3 and 4 of the gyro mode
P
memory (storage) is memorized.
To use (ET4, ET5), No,10526 Expert grip is required.
P
ー
The functions which may be set are both 3CH and 4CH.
When the 3ch/4ch mode is changed from GYRO mode
to another mode or OFF, the 3ch mode will return to the
setting for (OFF).
Please prepare the gyro system (ex. KR-212FHG)
separately. The gyro effect is not provided only in the
main system of transmitter.
29
：-100 〜 0（Default：-100）
：LOW 〜 HIGH（Default：0）
：0 〜 100（Default：100）
Center
2 Steps
100 Steps 100 Steps
Movement Range
Interval Position
Low Position
2 Steps
Maximum
Low Angle