Amp (Amp Mixing Menu) - Ko Propo EX-2 Instruction Manual

3・4CH 3・4ch Menu
▶ AMP Mixing MODE
Used when the front and rear wheels are controlled
by separate ESCs and motors. If 3CH or 4CH is set
to the front-wheel drive function, it will operate in
conjunction with 2CH's throttle operations.
3CH MODE ： AMP
MODE NORMAL
TH HOLD
HIPOINT 100
BRAKE 100
TRIM
REVERSE NORM
【Setting Range】
MODE （Default: NORMAL）
NORMAL(drives both front and rear wheels)
BURN(drives rear wheels only)
DIG(drives front wheels only)
F HOLD(drives front wheels at a set speed)
R HOLD(drives rear wheels at a set speed)
TH HOLD : -100 〜 100（Default: 0）
This function adjusts the set speed used for (F HOLD) and (R
HOLD) selected in Amp Mixing Mode.[F HOLD] adjusts the
front wheel drive while [R HOLD] adjusts the rear wheel drive.
※ This setting is activated when F HOLD or R HOLD mode
is selected.
【Example】 May be used for rock crawlers, etc.
HIPOINT : 0 〜 150（Default : 100）
Adjusts the maximum amount of throttle to be
applied to the front wheels. Equivalent to the
[Throttle High Point] function.
※ This setting is activated when NORMAL, DIG, or R
HOLD mode is selected.
This makes it easy to adjust the amount of maximum
P
throttle, particularly on a glow engine car.
If the amp mixing high point is set low and the amp
P
mixing trim is set to a high value toward acceleration,
the resulting throttle movement may be extraordinarily
small.
On glow engine cars, an overly high setting value will
increase load on the servo and lead to it being damaged.
Check carefully while adjusting.
On electric cars, a setting value that is too small
may cause problems with the ESC settings. Make
adjustments starting from the default setting (100).
Brake will not operate if the value is set to 0.
BRAKE : 0 〜 150（Default: 100）
Modify the maximum amount of reverse (brake) to
be applied to the front wheels.
Equivalent to [Throttle Brake] function.
※ This setting is activated when NORMAL, DIG, or R
HOLD mode is selected.
->KEY:OFF
0 ->KEY:OFF
->KEY:OFF
->KEY:OFF
0
->KEY:OFF >>>
On glow engine cars, an overly high setting value will
increase load on the servo and lead to it being damaged.
Check carefully while adjusting.
On electric cars, a setting value that is too small
may cause problems with the ESC settings. Make
adjustments starting from the default setting (100).
Brake will not operate if the value is set to 0.
TRIM : -50 〜 50（Default : 0）
Adjusts the neutral position of the front wheels.
The setting position cannot exceed what is set by [High
P
Point] or [Brake].
REVERSE : NORM（Normal） 、REVS（Reverse）
Changes the movement direction of the front
wheels.（Default: MORM)
For electric cars, the throttle is set by the ESC so there is
P
no need to set this function. However, some older ESCs
will not function properly unless reverse is also set.
MODE → KEY : OFF、ET1 〜 5（Default : OFF）
Assigns ET or BT keys to activate the various front
wheel drive modes.
TH HOLD → KEY : OFF、ET1 〜 5（Default : OFF）
Assigns ET keys to be used for the set speed used
for TH HOLD.
HIPOINT → KEY : OFF、ET1 〜 5（Default : OFF）
Assigns ET or BT keys to adjust HIPOINT value.
BRAKE → KEY : OFF、ET1 〜 5（ Default : OFF）
Assigns ET or BT keys to adjust BRAKE value.
REVERSE → KEY : OFF、ET1 〜 5（Default : OFF）
Assigns ET or BT keys to changes the movement
direction of the front wheels.
【Setting Range】
ET MODE SET
Assigns ET or BT keys to activate the various front
wheel drive modes.
3CH MODE:AMP
ET MODE SET
NORMAL :
BURN ：ON
DIG ：ON
F HOLD：ON
R HOLD：ON
＜＜＜
NORMAL : ON、OFF（Default : ON）
BURN : ON、OFF（Default : ON）
DIG : ON、OFF（Default : ON）
F HOLD : ON、OFF（Default : ON）
R HOLD : ON、OFF（初期値 : ON）
Assigning these keys may be convenient for rock
P
crawlers or when you need to adjust Amp Mixing
settings.
31
ON