Twin Servo (Twin Servo Mixing Menu); 4Ws (4Ws Mixing Menu) - Ko Propo EX-2 Instruction Manual

3・4CH 3・4ch Menu
▶ TWIN SERVO MODE
This function modifies the setting for using 2 steering
servo. Using left steering servo 1ch, and right steering
servo 3ch or 4ch.
【Example】
Ackerman control is possible when using for drift cars
using twin servos.
3CH MODE ： TWIN SERVO
LEFT −ST
（１CH）
L・LEFT 70％
L・RIGHT 70％
L・SPEED 100％
L・TRIM 0
【Setting Range】
LEFT-ST（1CH）
L-LEFT : 30 〜 100%（Default: 70%）
Sets the highest value for the 1CH servo left operation.
L-RIGHT : 30 〜 100%（Default: 70%）
Sets the highest value for the 1CH servo right operation.
L-SPEED : 1 〜 100%（Default: 100%）
Sets the steering speed for the 1CH servo operation.
L-TRIM : -50 〜 50（Default: 0）
Sets the neutral position for the 1CH servo operation
range.
RIGHT-ST
NORM（Nomal） 、REVS（Reverse） （Default: NORM）
Sets operation direction of 3CH or 4CH servo.
R-LEFT : 30 〜 100%（Default: 70%）
Sets the highest value for the 3(4)CH servo left operation.
R-RIGHT : 30 〜 100%（Default: 70%）
Sets the highest value for the 3(4)CH servo right operation.
R-SPEED : 1 〜 100%（Default: 100%）
Sets the steering speed for the 3(4)CH servo operation.
R-TRIM : -50 〜 50（Default: 0）
Sets the neutral position for the 3(4)CH servo
operation range.
RIGHT ー ST
NORM
R・LEFT 70％
R・RIGHT 70％
R・SPEED 100％
R・TRIM 0
▶ 4WS
This function is related to an R/C car's 4-wheel
steering feature. If 3CH or 4CH is assigned to control
the rear axle, it will operate in conjunction with 1CH
(steering). The direction of the rear axle steering may
also be changed.
3CH MODE ： ４WS
MODE NORMAL
LEFT 70
CENTER 0
RIGHT 70
TRVL 100
REVERSE NORM
【Setting Range】
MODE （Default: NORMAL）
NORMAL (front and rear axles turn in the same direction)
REVERSE (front and rear axles turn in opposite directions)
F STEER (steer front axle only)
R STEER(steer rear axle only)
LEFT : 0 〜 100（Default: 70）
Adjusts the rear axle servo movement range when
steering is turned to the left.
CENTER : -50 〜 50（Default: 0）
Adjust the rear axle servo's neutral position.
RIGHT : 0 〜 100（Default: 70）
Adjusts the rear axle servo movement range when
steering is turned to the right.
TRAVEL : 0 〜 150（Default: 100）
Adjusts the overall amount of movement of the rear
axle servo when the steering is at full lock.
REVERSE : NORM（Normal） 、REVS（Reverse）
（Default: NORM）
Sets operation direction of 3CH or 4CH servo.
MODE → KEY : OFF、ET1 〜 5（Default: OFF）
Assigns ET keys to be used for 4WS Mixing MODE.
CENTER → KEY : OFF、ET1 〜 5（Default: OFF）
Assigns ET keys to be used for 4WS Mixing CENTER.
TRVEL → KEY : OFF、ET1 〜 5（Default: OFF）
Assigns ET keys to be used for 4WS Mixing TRAVEL.
30
->KEY:OFF
->KEY:OFF
->KEY:OFF