Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for AngelTrax ATCF460 MDVR
Summary of Contents for AngelTrax ATCF460 MDVR
- Page 1 ATCF460 MDVR AngelTrax Mobile Digital Video Recorder Includes Quick Setup Guide Lists all the key features and settings for the ATCF460 MDVR Unit Installation User Menus and Settings Servicing Procedures Mobile DVR Installation, Setup and User Manual...
-
Page 2: Contact Information
| Mobile Video Surveillance Solutions IVS, Inc, dba AngelTrax AngelTrax designs, manufactures and supports mobile video surveillance for the school bus, mass transit, waste management and rail industries. AngelTrax drives the market with patented products, including distinctive DVR systems and Virtual Synchronized Mapping™... -
Page 3: About This Manual
Hybrid Quest™ User Manual Revision This is the June 2013 revision for this User Manual and is copyright, June 2013 of IVS, Inc. dba AngelTrax™ all rights reserved. Exclusion of Liability IVS, Inc.: This software is provided by the copyright and trademark holders and contributors “as is”, and any express or implied warranties, including, but not limited to, the implied warranties of merchantability and fitness for a particular purpose are disclaimed. - Page 4 The stability of the electrical system in the vehicle is critical to the performance and reliability of certain electronics installed onboard. These electronics rely on the vehicle’s power in order to be fully operational. AngelTrax components require stable voltage in order to function properly.
-
Page 5: Table Of Contents
Section 5: ATCF460 Menu and Setup ATCF460 Menu Outline ........................... 15 On-Screen Display Diagram ........................17 Using the ATCF460 Menu Section ......................19 Date/Time Setup Section ........................20 Vehicle ID Type and Number Section ....................23 Formatting the HDD Section ......................... 24 AngelTrax | iv... - Page 6 PTZ Section ............................... 41 DVR ID Section ............................41 Factory Default Section ..........................41 Update Code Section ..........................42 Audio Section ............................. 42 Key Lock Setup Section .......................... 43 Section 7: Recommended Preventative Maintenance Firmware Upgrade Section ........................45 AngelTrax | v...
- Page 7 Replacing the Compact Flash (CF) Card ....................47 Upgrading to VSM™ Section ......................... 48 Returning Product for Service Instructions ..................49 Section 9: Troubleshooting Guide Troubleshooting Guide for the ATCF460 .................... 50 Acronym Guide Acronym Guide ............................51 AngelTrax | vi...
-
Page 8: Section 1: Introduction
Panic ‘PANIC’ button for HDD event mark Delay Shutdown Previous versions have up to a 1 hour delay. Current versions have up to a 4 hour delay. Speed/GPS/Direction Data Optional G-Force Sensor Optional External VSM™ Module Optional AngelTrax | 1... -
Page 9: Parts List (General)
Other items may be included with your system based on your order. Please check the contents of your order carefully. If any items in your order are missing or damaged, please contact AngelTrax immediately by phone at 1.800.673.1788 or by email at support@angeltrax.com for further assistance. -
Page 10: Parts List (Accessory Box)
Wire ties • Stepper drill bit • Portable monitor with audio • Split loom • Fish tape • Various screwdrivers and nut • Connectors for signal inputs drivers (0.3125 in) • Various wire connectors • Rubber grommets AngelTrax | 3... -
Page 11: Section 2: Atcf460 Dvr Quick Setup Guide
Please refer to the following sections for information on the NOTICE: Use the arrow buttons located around the ENTER ATCF460 MDVR parts and functions: button near the top of the remote to navigate up, down, left or right on each menu list. Use the plus or minus buttons located Page 2 - Parts List (General) under the arrow buttons to adjust values. -
Page 12: Factory Default Settings
Menu again if you wish to return to the live camera view. NOTICE: When the vehicle type is changed, the signal wire labels will change. Please refer to the Driver Action-detecting per Vehicle Table, page 13, for more information. AngelTrax | 5... -
Page 13: Atcf460 Parts And Functions Diagram
Protects cable connections G-FORCE SENSOR (OPTIONAL FEATURE) GPS ANTENNA (OPTIONAL FEATURE) G Sensor Box EXTERNAL VSM™ (OPTIONAL FEATURE) • SD Data card slot (mapping) Power 0.5G 1.5G 2.5G • LED indicator • Signal input/output connection Signal I/O SIGNAL DATA AngelTrax | 6... -
Page 14: Installation Best Practices Section
CF card and USB port. Allow • Contact the AngelTrax technical support staff sufficient clearance behind the DVR for camera cables, mounting at 1.800.673.1788 before attaching the DVR to cables, Ethernet cables and power cables. -
Page 15: Post-Installation Checklist
Check all switches on vehicle control panel (fans, lights, etc) Make sure dip (delay time) switches are in the correct position Check for missing screws. Make sure panels are installed properly with no cracks in plastic Make sure camera grommets/wire loom are in place AngelTrax | 8... -
Page 16: Atcf460 Hardware Installation
Using the screws provided, attach the DVR to the bulkhead (see Figure 3). Connect the power cable to the power source, then connect the power cable and ignition to the MDVR (see Figure 4). Power-up the MDVR by turning on the vehicle’s ignition. AngelTrax | 9... - Page 17 (see Figure 9), to set the correct time (Refer to the Date/Time Setup Section, page 20, for detailed instructions). REWIND PLAY PAUSE STOP 14. Turn the vehicle ignition off and confirm the shut down delay is working properly. AUDIO QUAD AngelTrax | 10...
-
Page 18: Panic Button Connection Section
Event Marker Button Event Marker Button Event Marker Button GPS Signal Indicator Power Indicator Power Indicator (red) (red) GPS Signal Indicator Power Indicator GPS Signal Indicator Recording Indicator (green) (green) (*all indicators red) Recording Indicator Recording Indicator (amber) (amber) AngelTrax | 11... -
Page 19: Section 4: Atcf460 Connections, Ports And Controls
Alarm expansion: up to four (4) inputs and POWER CONNECTION one (1) output • Connects the key on the connection wire (yellow) to vehicle ignition ON position • Plugs the power cord to the battery (red) • Connects to the common vehicle ground (black) AngelTrax | 12... -
Page 20: Driver Action-Detecting Per Vehicle Table
DR - Door Open PE2 - Panic Event 2 MR - Microphone D:2 - Door 2 D:2 - Door 2 D:2 - Not used PE3 - Panic Event 3 Reception PANIC PANIC PANIC PANIC PE1 - Panic Event 1 AngelTrax | 13... -
Page 21: Dvr Remote Control Diagram
CAM2 CAM3 AUDIO CAM4 QUAD larger view CAM5 CAM6 CAM7 CAM8 CAM5 CAM6 CAM7 CAM8 CAM5 CAM6 CAM7 CAM8 CAM5 CAM6 CAM7 CAM1 CAM8 CAM2 CAM3 CAM4 Select the Video Channel to View CAM5 CAM6 CAM7 CAM8 AngelTrax | 14... -
Page 22: Section 5: Atcf460 Menu And Setup
Pre Record (on/off) (1*) These features are not applicable to the ATCF460 DVR. (2*) These features should be adjusted by AngelTrax personnel only. Please DO NOT adjust. (3*) These features are not used in the transportation industry. (4*) The PTZ feature is for future applications. Please DO NOT adjust. - Page 23 Alarm Out Factory Default Status (on/off) Time Load (yes/no) Sequence Setup Update Code (5)* Full Screen Format USB (yes/no) Firmware Upgrade USB (yes/no) Password Setup Load PC Player (yes/no) Firmware Upgrade CF (yes/no) Audio Input Volume Output Volume AngelTrax | 16...
-
Page 24: On-Screen Display Diagram
If both doors are open, D:12 will display. If there are no signal wires connected with the doors, D:-- will continue to display. The door signal is marked on the CF card, and will display in playback. AngelTrax | 17... - Page 25 If a GPS-E1 antenna is installed, the vehicle’s latitude and longitude is displayed on the (Available only with local monitor. When your recorded video data is reviewed with AngelTrax playback software, use of GPS-E1 each channel is marked with your vehicle’s tracking information.
-
Page 26: Using The Atcf460 Menu Section
DVR using the supplied cables (see Figure 1). You should now see a live view of your cameras. Please refer to the On-Screen Display Diagram, page 17, for an explanation of live camera view features (see Figure 2). AngelTrax | 19... -
Page 27: Date/Time Setup Section
NOTICE - TIME FORMAT SETTING: ENTER COPY Always program the hour as 24-hour (13:00) so the MDVR can distinguish between AM and PM, and display it accordingly. REWIND PLAY PAUSE STOP AUDIO QUAD CAM1 CAM2 CAM3 CAM4 AngelTrax | 20... - Page 28 As you scroll through the selections, different time zone regions will appear for reference. Press the Menu button to save the settings, and return to the Date/Time Setup menu. Press Menu again to return to the Main Menu. AngelTrax | 21...
- Page 29 If your unit has a GPS antenna, use plus/ minus buttons on the remote to turn ON, and the unit will automatically adjust. If no antenna is present, use plus/minus buttons on the remote to select your preferred Time Zone. AngelTrax | 22...
-
Page 30: Vehicle Id Type And Number Section
Press Menu again if you wish to return to the live camera view. NOTICE - CHANGING VEHICLE ID TYPE: When the vehicle type is changed, the signal wire labels will change. Please refer to the Driver Action- detecting per Vehicle Table, page more information. AngelTrax | 23... -
Page 31: Formatting The Hdd Section
Figure 3). After the CF card is formatted, a Format OK message will appear at the bottom of the HDD Format screen (see Figure 4). The CF card is now reset and enabled for recording. The system will return to live camera view, and record (REC) mode. AngelTrax | 24... -
Page 32: Camera Setup Section
CAUTION: The following section describes how factory default settings can be adjusted. However, it is NOT RECOMMENDED that these settings be altered. Please contact technical support at the AngelTrax corporate office regarding any questions or concerns you might have at 1.800.673.1788. -
Page 33: Color Setup Section
When turned ON, an alarm will sound if the camera is concealed by an object (i.e. a hand or ON / OFF article of clothing). If the system uses wireless technology, a notification can be sent via text message or email AngelTrax | 26... -
Page 34: Motion Detection Section
If you press the ENTER button on the remote while in the grid view, all the squares will activate. Press the ENTER button again, and all the squares will deactivate. Press the Menu button on the remote to save your changes and return to the Motion Detection screen. AngelTrax | 27... - Page 35 11. The Relay Out feature is used for connecting an external alarm. 12. After adjusting the Motion Detection settings, press the Menu button on the remote to save your changes, and return to the Camera Setup menu. Press Menu again to return to the Main Menu. AngelTrax | 28...
-
Page 36: Status Select Section
OFF the cameras (see Figure 12). Press the Menu button on the remote to save your changes and return to the Camera Setup menu. Press Menu again to return to the Main Menu. AngelTrax | 29... -
Page 37: Hdd Rec Mode Section
Press the plus or minus buttons on the remote again to change the record mode back to Recycle. 10. To save your changes and return to the HDD Setup menu, press the Menu button on the remote. AngelTrax | 30... -
Page 38: Hdd Format Section
The Auto Format feature under the HDD Setup menu should be ON. Disabling of this feature will result in the hard disk drive requiring manual formatting (when necessary). To save your changes and return to the Main Menu, press the Menu button on the remote. AngelTrax | 31... -
Page 39: Record Setup
Depending on your application, you can alternate or combine any of the three settings (Motion, Alarm and Continuous), throughout the day. To save your changes and return to the Record Setup menu, press the Menu button on the remote. AngelTrax | 32... -
Page 40: Continuous Record Section
Press the plus or minus buttons on the remote to turn the Record Select features (Camera Record and Camera Priority) ON or OFF (see Figure 7). To save your changes and return to the Record Setup menu, press the Menu button on the remote. AngelTrax | 33... -
Page 41: Alarm Record Section
Press the plus or minus buttons on your remote again to turn the Pre Record feature back to ON. To save your changes and return to the Record Setup menu, press the Menu button on the remote. AngelTrax | 34... -
Page 42: Motion Record Section
Press the plus or minus buttons on your remote again to turn the Pre Record feature back to ON. To save your changes and return to the Record Setup menu, press the Menu button on the remote. AngelTrax | 35... -
Page 43: Backup Setup Section
From the Main Menu, use the arrow buttons on the remote to select Peripheral Setup (see Figure 1), and press ENTER. There are four settings under the Peripheral Setup feature. Settings include: Buzzer Setup, Alarm Setup, Sequence Setup and Password Setup (see Figure 2). AngelTrax | 36... -
Page 44: Buzzer Setup Section
The length of time for the buzzer to sound may be adjusted from one to 60 seconds. To save your changes and return to the Peripheral Setup menu, press the Menu button on the remote. Alarm Setup THIS FEATURE IS NOT USED IN THE TRANSPORTATION/ MOBILE INDUSTRY . AngelTrax | 37... -
Page 45: Sequence Setup Section
To save your changes and return to the Peripheral Setup REWIND PLAY PAUSE STOP AUDIO QUAD menu, press the Menu button on the remote. AUDIO QUAD CAM1 CAM2 CAM3 CAM4 CAM1 CAM2 CAM3 CAM4 CAM5 CAM6 CAM7 CAM8 AngelTrax | 38... -
Page 46: Password Setup Section
Under the Confirm option, enter your password again and press ENTER. You will automatically be returned to the camera view screen. Contact the AngelTrax corporate office if you lose your password at 1.800.673.1788. AngelTrax | 39... -
Page 47: Sub Menu
Speed” event. This event will display on the playback software. To save your changes and return to the Sub Menu, press the Menu button on the remote. Press the Menu button again to return to the Main Menu. AngelTrax | 40... -
Page 48: G Sensor Menu Section
Load Factory Default option from NO to YES (see Figure 8). Press ENTER on the remote to reset all DVR settings back to the factory default settings. To save your changes and return to the Sub Menu, press the Menu button on the remote. AngelTrax | 41... -
Page 49: Update Code Section
Sub Menu (Cont.) Update Code CAUTION: THE UPDATE CODE FEATURE IS FOR ANGELTRAX PERSONNEL ONLY. DO NOT ADJUST. Audio Users may select one audio channel at a time (by pressing the Audio button on the remote), in order to hear audio for each camera separately. -
Page 50: Key Lock Setup Section
You may notice there is no password prompt after you initially set the Key Lock mode. You will need to turn the DVR off and restart the system before you receive a password prompt to access the Menu Selection mode. AngelTrax | 43... -
Page 51: Section 7: Recommended Preventative Maintenance
Section 7: Recommended Preventative Maintenance Performing the following preventative maintenance tasks on a regular schedule will help to keep your AngelTrax mobile DVR in the best condition and functioning correctly. Maintenance What to Do Make sure the ‘panic’ After the ignition is on for approximately 20 seconds, the amber (yellow) light should begin button LEDs are working flashing rapidly, indicating the DVR is recording. -
Page 52: Firmware Upgrade Section
Firmware Upgrade The upgrade will be on a Compact Flash (CF) card provided by AngelTrax™. Place the card into the CF port (see Figure 1). ATCF Use the black/gray remote provided, and press Menu. CF Port Use the arrow buttons on the remote to scroll down to Sub Menu (see Figure 2). - Page 53 The CF card will format and return to recording when finished. NOTICE - FORMATTING THE MDVR’S CF CARD: Formatting will ERASE ALL INFORMATION ON THE COMPACT FLASH CARD. If you have any information you need off the card, be sure to retrieve it first. AngelTrax | 46...
-
Page 54: Section 8: Servicing Your Atcf460 Dvr
ATCF460 DVRs are some of the most advanced mobile recording devices available. These rugged devices are based on our patented technology and ensure worry-free service for years to come. However, should you have any questions or concerns, please contact technical support at the AngelTrax corporate office at 1.800.673.1788. Replacing the Compact Flash (CF) Card... -
Page 55: Upgrading To Vsm™ Section
(connected to Number 2 on the ATCF460 Connections, Ports and Controls, page 12) - see Figure 5). With the supplied Allen screwdriver, replace the two screws on the DVRs back cover (see Figure 6). Camera 3 connection AngelTrax | 48... -
Page 56: Returning Product For Service Instructions
You will receive a copy of the RMA and a Call Tag with the replacement unit, allowing you to ship the defective product back at no cost. Once you receive the replacement unit, you have 30 days to ship the defective unit back to AngelTrax or you will be charged for the replacement product. -
Page 57: Troubleshooting Guide For The Atcf460
The camera connection is loose on one of the camera inputs. • There is a problem with the Compact Flash card. If your problem requires additional assistance not covered in this guide, please contact technical support at the AngelTrax corporate office at 1.800.673.1788. AngelTrax | 50... -
Page 58: Acronym Guide
Millimeters External MPEG Motion Picture Experts Group file containing Federal Communications Commission the compression of audio and visual data Frames Per Second NAND Not And (used as a logical operator in computing) Gigabyte AngelTrax | 51... - Page 59 Thin Film Transistor Technical Specifications Underwriters Laboratory Universal Serial Bus Coordinated Universal Time Volts, Direct Current Virtual Synchronized Mapping™ Watt(s) Wi-Fi Wireless Fidelity WiMAX Worldwide Interoperability for Microwave Access, Inc. WLAN Wireless Local Area Network Windows Media Video AngelTrax | 52...
Need help?
Do you have a question about the ATCF460 MDVR and is the answer not in the manual?
Questions and answers