Yamaha FZ1-N 2007 Service Manual page 95

Manuals by Motomatrix / www.motomatrix.co.uk / The Solution For Lost Motorcycle Coded Keys
FZ1-N(W)/FZ1-S(W)
1. Throttle cables
2. Right handlebar switch lead
3. Wire harness
4. Throttle cable (pull side)
5. Throttle cable (return side)
6. Radiator fan motor lead (Right)
7. Coolant reservoir tank hose
8. Radiator inlet hose
9. Air filter drain hose
10.Crankshaft position sensor lead
11.Direct ignition coil lead coupler
12.Immobilizer anti-theft alarm coupler
13.Engine ground lead
14.Neutral switch lead
15.Rear brake light switch lead
16.EXUP cable
17.EXUP servo motor
18.Main fuse
19.Atmospheric pressure sensor
20.Battery positive lead
21.Radiator fan motor relay
22.Starting circuit cut-off relay
23.Fuse box
24.Lean angle sensor
25.Turn signal light lead (right)
26.License plate light lead
27.Turn signal relay
28.Turn signal light lead (left)
29.Seat lock cable
30.Tail/brake light lead
31.Tail/brake light lead coupler
32.Headlight relay
33.Turn signal light lead coupler (left)
34.Starter relay
35.Fuel tank breather hose
36.Battery negative lead
37.AC magneto lead
38.Starter motor lead
39.Coolant reservoir tank drain hose
40.Fuel hose bend R section
41.Idle adjust screw wire
42.Throttle body lead
43.Air cut-off valve hose
44.ECU (engine control unit)
45.Water pump breather hose
46.Radiator fan motor lead (left)
47.Clutch cable
48.Left handlebar switch lead
49.Immobilizer lead
50.Main switch lead
51.Frame
52.Cover
email: info@motomatrix.co.uk
53.Direct ignition coil lead
54.Speed sensor lead
55.Lean angle sensor lead
56.Battery box
57.Turn signal light relay lead
58.Rear frame
59.Battery
60.Sidestand switch lead
61.Oil level switch lead
62.O sensor lead
2
63.Velcro
64.Protector
65.Mad guard
66.Fender
67.Fuel hose
A. Check that it is secured with the guide of
the radiator stay.
B. 10–30 mm (0.39 to 1.18 in)
C. To the direct ignition coil lead
D. Make sure to install the air filter after
checking that the leads are positioned out-
side of the vehicle from the throttle body
side cover.
E. To the engine
F. Direct ignition coil lead protector edge
G. Bind the left handle bar switch leads, main
switch leads, right handle bar switch leads,
immobilizer leads, radiator fan motor leads
(right), wire harness and direct ignition
leads (in random order). Make sure to set
the clamping position to be ahead of the
immobilizer anti-theft alarm coupler and
rear brake switch leads branch position,
and to be within a range of 0 to 30 mm (0
to 1.18 inches) away from the protector
end of the direct ignition coil lead. Install
the band pointing its tip end downward
inside the vehicle.
H. Route the pickup coil lead below the fuel
hose, throttle body hoses and air filter drain
hose.
I. 0–30 mm (0 to 1.18 in)
J. Route the wire harness below the clutch
cable and route the coupler branched from
the wire harness below the clutch cable
and then connect it.
K. Insert the wire harness wrapping clamp to
the hole of the frame.
L. To the rear brake light switch
M. Open to the air
N. Insert the main fuse to the battery band.
Soapy water can be spread.
O. Route the battery positive lead under the
relays.
P. Route the fuse box lead under the radiator
fan motor relay.
Q. Route the battery positive lead under the
fuse box lead.
2-52
CABLE ROUTING