Yamaha FZ1-N 2007 Service Manual page 101

Manuals by Motomatrix / www.motomatrix.co.uk / The Solution For Lost Motorcycle Coded Keys
N. Route the battery positive lead under the
fuse box lead.
O. Pass the license plate light lead and turn
signal light lead under the turn signal relay.
P. Pass the turn signal light lead (right) and
license plate light lead under the rear
fender bracket and route between the ribs
of the battery box.
Q. Pass the turn signal light lead (left) and tail/
brake light lead under the rear fender
bracket and route between the ribs of the
battery box.
R. Route the battery positive lead from the
inner side of the vehicle to the down side of
the wire harness. It is not allowed to route
the lead over the wire harness.
S. Route it so that the branch connection of
the main fuse lead is placed in the upper
side.
T. Route the rear wheel sensor lead under
the rear brake fluid reservoir tank .
U. To the speed sensor
V. To the fuel pump
W. Fit so that the engine ground lead is posi-
tioned below and the battery negative lead
above. Fit the leads so that each projection
of lead is positioned on the upper side of
the vehicle.
X. To the starter motor
Y. Route the intake air temperature sensor by
the upper side of the air filter drain hose.
Z. Route the leads under the throttle bodies.
AA.To the air filter case
AB.Positioning tape (shaded area)
AC.Fit the protector by aligning the positioning
tape end and protector end for the main
switch lead, immobilizer lead and left han-
dlebar switch lead. The misalignment toler-
ance of ends is 0 to 5 mm (0 to 0.20 in).
AD.Paste wire harness aligning with the mark-
ing-off on the front upper body so that the
opening points toward the upper side of the
vehicle.
AE.Place clamp along with the lower side
clamp and paste with the clamp width
shifted by half to the rear side of the vehi-
cle. Point the opening section of the clamp
is upward on the vehicle.
AF.Insert the ABS check coupler to the stay so
that the attaching section points to the out-
side of the vehicle.
AG.Attach the ground lead at 45° or less.
AH.Point the ground lead to the direction in
parallel to the bracket end face.
AI. 15 × 20 mm (0.59 × 0.79 in) (shaded area)
email: info@motomatrix.co.uk
AJ.Installation procedure 1. Secure the main
switch lead and immobilizer lead with Vel-
cro strap. 2. Secure the left handlebar
switch lead with Velcro strap. The main
switch lead and immobilizer lead shall not
be twisted in the protector. The installation
position is where the protector end and
lead positioning tape end align.
AK.The inside of the vehicle.
AL.20 × 58 mm (0.79 × 2.28 in) (shaded area)
AM.The upper side of the vehicle.
AN.Clamp each lead at the positioning taping
section (white) and then insert it to the
cover. (In random order)
AO.Cut clamp leaving 2 to 4 mm (0.08 to
0.16in) of the tip.
AP.Can be routed in random order.
AQ.Clamp each lead at the positioning taping
section (blue) and then insert it to the
cover. For routing leads, the wire harness
shall be downside but others can be in ran-
dom order. Positioning tape is only used for
the handlebar switch lead and ABS sensor
lead.
AR.Clamp the fuel hose and direct ignition coil
lead. Point the latch and the opening sec-
tions of the clamp to the front side of the
vehicle and install it at the position as
shown in the illustration.
Clamp it tightly until the last (the third) latch
is hooked.
AS.The front side of the vehicle.
AT. 0 to 90 angle
AU.Secure the leads with a clamp. The cut
position of the tip of the clamp shall be on
the upper side of the vehicle. (Cut it leaving
2 to 4 mm (0.08 to 0.16in) of the tip). Route
the leads over the frame plate and insert
them through the hole into the inside of the
vehicle. Route the wire harness at the posi-
tion shown in the illustration and other
leads can be in random order. Inserting the
band can be in any direction.
AV.Attach so that the outer groove of the cap
is to be positioned at the corner of the nut.
AW.Push the wire harness securely in as far
as it will go.
AX.Route the ABS fuse lead at the uppermost
side of the vehicle. Also, it must not be pro-
truded from the battery box ribs toward the
upper side.
AY.Route it between the battery box ribs in the
order indicated in the illustration.
AZ.Route the two headlight leads under the
cap nut.
2-58
CABLE ROUTING