Page 1 HX3 Wearable Computer User’s Guide...
Page 2 Disclaimer Honeywell International Inc. (“HII”) reserves the right to make changes in specifications and other information contained in this document without prior notice, and the reader should in all cases consult HII to determine whether any such changes have been made.
Page 3: Table Of Contents
Ring Scanner and Ring Imager Extended Cable................. 2-4 Audio Connector and Battery Connection Cable ................. 2-4 Li-Ion Battery ..........................2-5 Assembling the HX3 Voice Computer and Accessories ..............2-6 Assembling the Headset Cable ....................2-6 Adjusting Headset / Microphone and Securing Cable ..............2-7 Connecting the Cable to the Battery....................
Page 4 Chapter 5 - Software Configuration Using ActiveSync..........................5-1 Initial Setup ............................5-1 Connect via USB..........................5-1 Cable for USB ActiveSync Connection..................5-2 Synchronizing from the HX3 ......................5-2 Explore ............................5-2 Backup Data Files using ActiveSync....................5-2 Connect ..........................5-3 Disconnect ..........................5-3 Cold Boot and Loss of Host Re-connection .................5-3...
Page 5 Configuring the HX3 with LXEConnect ..................5-4 Install LXEConnect ........................5-4 Using LXEConnect ........................5-6 Operating System and Software Load....................5-7 Windows CE Operating System....................5-7 General Windows CE Keyboard Shortcuts ..................5-7 Reboot............................5-7 Warmboot ..........................5-7 Coldboot ..........................5-8 Clearing Persistent Storage / Reset to Default Settings ..............5-8 Folders Copied at Startup ......................5-8...
Page 6 HX3 OS Upgrade..........................5-17 Preparation..........................5-17 Procedure...........................5-17 Battery State and OS Upgrade ....................5-17 Control Panel............................5-18 About............................5-19 Version Tab and the Registry ....................5-19 Languages ...........................5-19 Identifying Software Versions ....................5-19 MAC Address ........................5-19 Battery............................5-20 Backup Battery Maintenance....................5-20 Certificates ..........................5-21 Date / Time..........................5-22 Device Management ........................5-22 Dialing ............................5-23...
Page 7 Netlog ..........................5-41 Command ........................5-41 Options .........................5-41 Run cmd ........................5-41 NDISLog ..........................5-42 Command ........................5-42 file ..........................5-42 Save File ........................5-42 Run cmd ........................5-42 Owner............................5-43 Password ...........................5-44 PC Connection ...........................5-45 Power ............................5-46 Regional and Language Settings ....................5-48 Remove Programs ........................5-49 System ............................5-50 General Tab.........................5-50 Memory Tab ........................5-50 Device Name Tab ........................5-51 Copyrights Tab ........................5-51...
Page 8 Bluetooth Printer Setup ......................6-15 Easy Pairing and Auto-Reconnect .....................6-15 Using OPP ............................6-16 Pairing with an OPP Device .......................6-16 Remote Device Pushes File to HX3...................6-16 HX3 Pushes File to Remote Device...................6-17 LXEZ Pairing and External Application.....................6-17 Chapter 7 - Bar Code Scanner Wedge Introduction ............................7-1...
Page 9 Add ..........................7-6 Insert ..........................7-6 Edit ..........................7-6 Clear All ..........................7-6 Remove ..........................7-7 Control Code Replacement Examples...................7-7 Bar Code Processing Examples ....................7-7 Bar Code - Ctrl Char Mapping......................7-9 Translate All...........................7-9 Character ..........................7-9 Replacement .........................7-9 List Box ..........................7-10 Assign Button ........................7-10 Delete Button ........................7-10 Bar Code - Symbology Settings ....................7-10 Enable ..........................7-11 Min ............................7-11...
Page 10 Server Contact........................8-8 ...............................8-8 Data ............................8-9 Preferences .........................8-10 Display ..........................8-11 Taskbar..........................8-12 Execution ..........................8-13 Scan Config .........................8-14 Shortcuts ..........................8-15 SaaS ............................8-16 Adapters ..........................8-17 Status ..........................8-20 Startup/Shutdown ........................8-21 Exit............................8-22 Using Remote Management ......................8-22 Using eXpress Scan .........................8-22 Step 1: Create Bar Codes ......................8-22 Step 2: Scan Bar Codes......................8-23 Step 3: Process Completion.......................8-24 Chapter 9 - Wireless Network Configuration...
Page 11 USB Cable ..........................11-5 Serial Cable..........................11-6 Indicators ............................11-6 Cradle PWR LED ........................11-7 B1 and B2 LED ..........................11-7 Docking and Undocking the HX3......................11-7 Docking the HX3 ........................11-8 Undocking the HX3 ........................11-8 Docked HX3 Mode States ........................11-8 Ring Scanner Storage ........................11-8 Inserting and Removing a Tethered Battery ..................11-9 Inserting a Tethered Battery into the Charging Bay ..............11-9...
Page 12 Charger Cleaning, Storage and Service ..................12-10 Battery Cleaning, Storage and Service ..................12-10 Chapter 13 - Specifications and Reference Material Technical Specifications ........................13-1 HX3 Voice Computer .........................13-1 Dimensions and Weight ......................13-1 Environmental Specifications .....................13-1 Network Card Specifications ......................13-2 Summit 802.11 b/g CF 2.4GHz....................13-2 Summit 802.11 a/b/g CF 2.4/5.0GHz...................13-2...
Page 13: Chapter 1 - Hx3 Agency Compliance
HX3 Agency Compliance HX3 mobile voice computers meet or exceed the requirements of all applicable standards organizations for safe operation. However, as with any electrical equipment, the best way to ensure safe operation is to operate them according to the agency guidelines that follow.
Page 14: Laser Warnings
• Do not remove the laser caution labels from the tethered ring bar code decoder. • Do not connect the laser bar code aperture to any other device. The laser bar code aperture is certified for use with the HX3 only.
Page 15: Beam Divergence
Beam Divergence See dimension of field below Width of Field 20” 50.8 cm 15” 38.1 cm 10” 31.6 cm 5” 12.7 cm 0” 0 cm 5” 12.7 cm 10” 31.6 cm 15” 38.1 cm 20” 50.8 cm 0” 5” 10” 15”...
Page 16: Fcc Part 15 Statement
“Something About Interference.” This is available at FCC local regional offices. Honeywell is not responsible for any radio or television interference caused by unauthorized modifications of this equipment or the substitution or attachment of connecting cables and equipment other than those specified by Honeywell. The correction is the responsibility of the user.
Page 17: Ce Mark
5627 BT Eindhoven The Netherlands Honeywell shall not be liable for use of our product with equipment (i.e., power supplies, personal computers, etc.) that is not CE marked and does not comply with the Low Voltage Directive. RF Safety Notices This device contains transmitter Module FCC ID: KDZLXE4830P.
Page 18: China Rohs
China RoHS HX3 佩戴式数据终端 (Wearable Computer) 有毒有害物质名称及含量的标识 (Names and Content of Hazardous Substances or Elements) 部件名称 (Parts Name) 有毒有害物质或元素 (Toxic and Hazardous Substances or Elements) 铅 (Pb) 汞 (Hg) 镉 (Cd) 六价铬 (Cr6+) 多溴联苯 (PBB) 多溴二苯醚 (PBDE) 印刷电路部件 (PCA) 无綫通信设备 (Wireless Communication Device) 备份电池...
Page 19: Chapter 2 - Getting Started
The HX3 can be docked in a desktop cradle. The HX3 batteries can be re-charged while the HX3 is in the desktop cradle. The batteries are also re-charged in a Battery Charger. When the HX3 is docked in a powered desktop cradle, connection is broken between the tethered battery and the HX3.
Page 20: Components
9. Blue Modifier Key 10. Microphone 11. Power Button Back View HX3 Worn on Left Side, Ring on Left Hand HX3 Worn on Right Side, Ring on Right Hand 1. Ring Scanner Tether cable channel 1. Tethered Battery Cable channel 1.
Page 21: Ring Scanner / Audio / Battery Connectors
• Tethered Battery Cradle Connector Connector 3 is at the base of the HX3. It connects to the Cradle. When the HX3 is in a powered desktop cradle, the HX3 receives external power through the cradle connector. USB Keyboard or USB Mouse input is received by the HX3 through the cradle connector when the HX3 is in a powered desktop cradle.
Page 22: Laser Imager
2. Scan Window 3. Trigger 4. Ring Strap 5. Connector (Connect to HX3) Ring Scanner and Ring Imager Extended Cable Clips are used to secure the cable to clothing. Wristband is used to secure the cable to the user's wrist.
Page 23: Li-Ion Battery
Li-Ion Battery The HX3 cannot function unless a battery is securely tethered. Be sure to place the HX3 in Suspend mode before disconnecting a battery, or all unsaved data may be lost Standard Battery Extended Battery 1. Battery Charge/Connect Terminals 2.
Page 24: Assembling The Hx3 Voice Computer And Accessories
1. Connect the HX3 voice cable I/O connector to the I/O port on the HX3. The HX3 internal microphone and speaker are automatically disabled. click! 2. Slide the voice cable ends together until they click and lock in place. Do not twist or bend the connectors. The HX3 is ready for voice-enabled applications. 2 - 6...
Page 25: Adjusting Headset / Microphone And Securing Cable
The headset consists of an earpiece, a microphone, a clothing clip and a cable. The headset attaches to the audio cable end of the voice cable which attaches to the HX3. Do not twist the microphone boom when adjusting the microphone. The microphone should be adjusted to be about two finger widths from your mouth.
Page 26: Connecting The Battery Cable To The Hx3
When you want to switch connectors from left to right, or vice versa, first gently press downward on the Retaining Clip, then pinch and pull the cable connector (not the cable!) straight up and away from the HX3. Do not use a metal object, or extreme force, to remove the cable connector from the HX3.
Page 27: Attaching The Ring To Your Finger
Attaching the Ring to your Finger The ring finger loop is located under the ring assembly. 1. Slide finger into opened loop 2. Remove shipping film on scan aperture before first bar code scan 3. Tighten the finger loop strap 4.
Page 28: Assembling The Voice Case
If the voice case is damaged, it should be removed from service. 10. An HX3 with a voice case does not fit in the desktop cradle. Remove the voice case before placing the HX3 in the desktop cradle.
Page 29: Setting Up The Software On The Hx3
HX3. If the first screen displayed on the host computer is the HX3 End User Licensing Agreement, click the Accept button to accept the EULA. The HX3 proceeds to start up and the System LEDs begin to flash.
Page 30: Set Date And Time Zone
You can also select / deselect sounds for key clicks and screen taps and whether each is loud or soft. As the volume scrollbar is moved between Loud and Soft, the HX3 emits a tone each time the volume increases or decreases.
Page 31: Connecting Bluetooth Devices
• The system administrator has also assigned a Computer Friendly Name using LXEZ Pairing Control Panel for the HX3. To connect Bluetooth devices, the HX3 should be as close as possible and in direct line of sight (distances up to 32.8 feet or 10 meters) with the targeted Bluetooth device during the discovery and pairing process.
Page 32: Reboot
New batteries must be fully charged prior to first use. Li-Ion batteries (like all batteries) gradually lose their capacity over time (in a linear fashion) and never just stop working. This is important to remember – the HX3 is always ‘on’ even when in the Suspend state and draws battery power at all times.
Page 33: Chapter 3 - Hardware Configuration
HX3. The main battery is either the 2000 mAh (Standard) or the 4000 mAh (Extended) battery. Only one main battery can be tethered to the HX3 at a time. The batteries can be hot-swapped after the HX3 is placed in Suspend mode.
Page 34: Bluetooth
Docked HX3 -- An uninterrupted external power source (wall AC/DC adapter connected to the HX2 cradle) transfers signals from the USB ports in the front of the cradle and the serial port on the back of the cradle, to the HX3. HX3 frequent connection to a fully charged tethered battery, is recommended to maintain backup battery charge status, as the backup battery cannot be recharged by a dead or missing tethered battery.
Page 35: Audio Support
The internal speaker supplies audible verification signals normally used by the Windows CE operating system. The speaker is located on the front of the HX3, above the [ 2 ] key. The mobile device emits a Sound Pressure Level (loudness) of at least 102 dB measured as follows: Frequency: 2650 + 100 Hz Distance: 10 cm on axis in front of Speaker opening in front of unit.
Page 36 3 - 4...
Page 37: Chapter 4 - Power Modes And Batteries
A suspended HX3 maintains the date and time for a minimum of two days while tethered to a battery that has reached the Low Warning point and a fully charged backup battery. The HX3 retains data, during a battery hot swap, for at least 5 minutes.
Page 38: Checking Battery Status
HX3 in a powered docking cradle before replacing the battery pack. When the main battery power level is low, the HX3 will signal the user with the low battery warning indicator (the Status LED remains a steady red) that continues until the main battery is replaced, the battery completely depletes, or external power is applied to the HX3 using a powered cradle.
Page 39: Backup Battery
Though data is retained, the HX3 cannot be used until a charged main battery pack is connected. After tethering the full battery, press the Power key.
Page 40 4 - 4...
Page 41: Chapter 5 - Software Configuration
Tap the Change button. From the popup list, choose USB Client. This will set up the HX3 to use the USB port. Tap OK and ensure the check box for “Allow connection with desktop computer when device is attached” is checked.
Page 42: Cable For Usb Activesync Connection
When a cradle is used: HX2312DSKCRDL or HX2313DSKCRDL - HX2-labeled desktop cradle Use with standard USB cable with type A plug for PC/Laptop USB port and type B plug for HX3 cradle USB type B cli- ent port. • Plug the type B end of the standard USB cable plug into the USB type B port on the desktop cradle (port #2).
Page 43: Connect
Solution: One or more control lines are not connected. This is usually a cable problem. If the HX3 is connected to a host computer by a cable, disconnect the cable from the HX3 and reconnect it again. Issue: ActiveSync indicator on the host (disc in the toolbar tray) turns green and spins as soon as you connect the cable, before tapping the Connect icon (or REPLLOG.EXE in the Windows directory).
Page 44: Configuring The Hx3 With Lxeconnect
HX3 and the PC. If the HX3 uses a serial port for ActiveSync, it will be necessary to configure the HX3 to use the serial port. Complete details on the proper cables and port configuration are included in Initial Setup (page 5-1).
Page 45 (page 14-1) for the necessary files if this folder is not present . 7. Select and copy the LXEConnect.msi and Setup.exe files from the HX3 to the host computer. Note the location chosen for the files. 8. Close the ActiveSync explorer dialog box. Do not disconnect the HX3 ActiveSync connection.
Page 46: Using Lxeconnect
Connect window on the host computer desktop. The dialog box automatically times out and disappears after approximately 20 seconds. 5. The HX3 can now be configured from the host computer LXEConnect window. Input from the PC’s mouse and keyboard are recognized as if they were attached to the HX3.
Page 47: Operating System And Software Load
The examples found in this section are to be used as examples only, the configuration of your specific HX3 computer may vary. The following sections provide a general reference for the configuration of the HX3 and some of its optional features.
Page 48: Coldboot
A cold boot is initiated by running the Coldboot application in the Windows folder. This application automatically cold boots the HX3, erasing any customer applied registry changes and returning the HX3 to its factory settings. Clearing Persistent Storage / Reset to Default Settings The coldboot utility sets all registry settings back to factory defaults.
Page 49: Software Applications
Access Files on the Flash Card Click the My Device icon on the Desktop then click the System icon. A flash card is used for permanent storage of the HX3 drivers, CAB files and utilities. It is also used for registry content back up.
Page 50: Launch.exe And Persistent Storage
(*.REG), or sound files (*.WAV). The mechanism is the same as listed above, but the appropriate CE application is called, depending on file type. Note: Registry entries may vary depending on software revision level and options ordered with the HX3. LAUNCH.EXE and Persistent Storage...
Page 51: Regload.exe
The REG.TXT file is not saved in persistent storage. To use the REG.TXT file as a reference in the event of a , copy the file to the System folder on the HX3 or store a copy of the REG.TXT file on a PC.
Page 52: Desktop
Wavelink® Avalanche Mobility Center™ (Avalanche MC) is a remote client management system that is de- signed to distribute software and configuration updates to monitored devices. The enabler for Wavelink Ava- lanche is loaded on the HX3 but not installed. When the enabler is installed this icon is displayed on the desktop.
Page 53: My Device Folders
Refer to Start > Help for an explanation of standard Windows CE taskbar icons. Following are a few of the HX3 unique taskbar icons that may appear in the Taskbar. These icons are in addition to the Windows CE taskbar icons.
Page 54: Internet Explorer
Transfer files between a HX3 and a host computer. ActiveSync is pre-loaded on the HX3. Using Microsoft ActiveSync you can copy files from your HX3 to your desktop computer , and vice versa. Once an ActiveSync relationship (part- nership) has been established with Connect (on a host computer), ActiveSync will synchronize using the wireless link, serial port, or USB to the HX3.
Page 55: Remote Desktop Connection
Windows PC Microsoft Remote Desktop Connection options. If installed, Remote Desktop Connection on the HX3 can be accessed by Start > Programs > Remote Desktop Connection. Select a computer from the drop down list or enter a host name and tap the Connect button. Tap the Options >> button to access the General, Display, Local Resources, Programs and Experience tabs.
Page 56: Taskbar
Clicking the Taskbar option on the Settings menu displays the Taskbar General tab and the Taskbar Advanced tab. Note: HX3 applications, operating system settings and control panels can be viewed and edited / updated using LXEConnect and ActiveSync on a host computer cabled to the HX3.
Page 57: Hx3 Os Upgrade
4. Maintain an uninterrupted AC/DC power source to the HX3 throughout this process. The SD / CF card with the OS and system files must be present for the HX3 to boot. Removal or installation of SD or CF cards must be performed on a clean, well-lit surface.
Page 58: Control Panel
Control Panel Note: Although the HX3 has no display or alphanumeric keypad, HX3 control panels can be viewed and settings manipulated using LXEConnect and ActiveSync on a connected host computer. Tap the ? button for Help when changing HX3 Control Panel options.
Page 59: About
The Versions tab displays the versions of many of the software programs installed. Not all installed software is included in this list and the list varies depending on the applications loaded on the HX3. The Image line displays the revision of the system software installed. Refer to the last three digits to determine the revision level.
Page 60: Battery
Jacked is shown in the Status box when the Main battery is receiving external power. The main battery is charged/recharged when the HX3 is docked in a powered cradle or directly cabled to an external power source.
Page 61: Certificates
Certificates Start > Settings > Control Panel > Certificates Manage digital certificates used for secure communication. Digital certificates are date sensitive. If the date on the HX3 is incorrect, wireless authentication will fail. The Certificates stores lists the certificates trusted by the HX3 mobile device user.
Page 62: Date / Time
Date / Time Start > Settings > Control Panel > Date/Time - or - Time in Desktop Taskbar Use this HX3 panel to set Date, Time, Time Zone, and assign a Daylight Savings location. Setting Default Current Time Midnight Time Zone...
Page 63: Dialing
Dialing Start > Settings > Control Panel > Dialing Set dialup properties for internal modems (not supplied or supported on the HX3). Setting Default Location Work Area Code Tone Dialing Enabled Country/Region Disable Call Waiting Disabled (blank) 5 - 23...
Page 64: Display
The display might also called the touch screen. Select the desktop background image and appearance scheme for the HX3. Using the options on the Backlight tab, set the display backlight and keypad backlight timers when running on battery or external power.
Page 65: Appearance
Appearance There is very little change from general desktop PC Appearance options. Select a scheme from the dropdown list and make changes to the parameters. The default is High Contrast White for monochrome displays and Windows Stan- dard for color displays. Tap the Save button to save any changes, renaming the scheme if desired. Tap the Delete but- ton to delete schemes.
Page 66: Hx2-3 Options
Start > Settings > Control Panel > HX2-3 Options Set options such as IP V6 and time sync. It may be necessary to warmboot the HX3 after making desired changes. A pop up window indicates if a warmboot is required.
Page 67: Misc
Misc Options on this tab configure device specific options. Note that options not available on the HX3 are dimmed or grayed out. Enable Auto Launch IP Wait When enabled, this feature works as follows: 1. After the radio .CAB file is unpacked, the Launch program waits for the radio driver to load and for the radio to connect and obtain an IP address.
Page 68: Installed Programs
Installed Programs Start > Settings > Control Panel > Installed Programs Note: This panel shows the programs installed in RAM. View the list of installed programs. No user interaction is required or allowed. In some OS versions, this panel replaces Remove Programs. Note: Contact Customer Support (page 14-1) if installed programs must be deleted.
Page 69: Keyboard
Keyboard Start > Settings > Control Panel > Keyboard Set keypad key map, keypad key repeat delay, and key repeat rate. Setting Default Key map Default (or Default HX3) Repeat charac- Enable Repeat Delay Short Repeat Rate Slow Select a key map using the drop-down list. Adjust the character repeat settings and tap the OK button to save the changes.
Page 70: Keypad
KeyPad Start > Settings > Control Panel > KeyPad Icon Use this control panel option to assign key functions to mappable keys available on your HX3, determine application launch sequences and program command Run sequences. Setting Default KeyMap Modifier Mode...
Page 71: Remap A Key To A Single Key
Assign settings by clicking radio buttons and selecting keys from the drop down boxes. Tap the OK button when fin- ished. The changes take effect immediately. Remap a Key to a Single Key 1. Select the modifier key from the Modifier Mode options. 2.
Page 72: Remap A Key To A Key To A Sequence Of Unicode Values
Remap a Key to a Key to a Sequence of Unicode Values Up to 16 Unicode values may be specified for the key sequence. The sequence can consist of keys and Unicode values. 1. Select the modifier key from the Modifier Mode options. 2.
Page 73: Launchapp Tab
The default for all text boxes is Null or “ ”. The text boxes accept string values only. Note that executables and parameters are not checked for accuracy by the keyboard driver. If the launch fails, the HX3 emits a single beep, if the launch is successful, it is silent.
Page 74: Runcmd Tab
The default for all text boxes is Empty, Null or “ ”. The text boxes accept string values only. Note that executables and parameters are not checked for accuracy by the keyboard driver. If the launch fails, the HX3 emits a single beep, if the launch is successful, the mobile device is silent.
Page 75: License Viewer
License Viewer Start > Settings > Control Panel > License Viewer Use this option to view software license registration details, and service contract length for an HX3. Information on the License Viewer tabs is unique for each HX3. Note: Following image is a sample screen.
Page 76: Mixer
Start > Settings > Control Panel > Mixer The HX3 has a speaker and a microphone. They are active when a headset is not connected to the device. The microphone is located to the right of the oval logo at the top of the unit.
Page 77: Input Panel
Input Panel Option Function Input Determines the audio input used (options available depend on the state of the Mic and Audio Out- put parameter): • None - No microphone is enabled. • Auto Ext Mic - (default) Automatically switch between internal microphone (when no cable is attached) and external microphone (when cable is attached) depending on presence of audio cable.
Page 78: Mouse
Mouse Start > Settings > Control Panel > Mouse Note: The HX3 does not have a touch screen. If the host computer has a touch screen, instructions using “tap” and “stylus” instead of “click” and “mouse” apply. Note: Use this option to set the double-tap sensitivity for stylus taps on the HX3 touch screen.
Page 79: Network And Dialup Options
Network and Dialup Options Start > Settings > Control Panel > Network and Dialup Connections Set HX3 network driver properties and network access properties. Select a connection to use, or create a new connection. Create a New Connection 1. On the mobile device, select Start > Settings > Control Panel > Network and Dialup Connections. A window is displayed showing the existing connections.
Page 80: Network Capture
Network Capture Start > Settings > Control Panel > Network Capture Verify the date and time are correct before using the logging utilities to ensure meaningful data. The Network Capture panels provide configuration options for logging utilities. Two types of logging are configurable: Netlog is a Windows CE utility that monitors network traffic.
Page 81: Netlog
Netlog Use this control panel to configure the Netlog utility. By configuring Netlog using the control panel, Netlog remains run- ning across a warmboot. However, note that: • Netlog first stores data to a file named netlog0.cap, then netlog1.cap. Any time the current file reaches maximum size, Netlog switches to the other file.
Page 82: Ndislog
NDISLog NDISLog creates a .TXT file that can be viewed with any text editor program that supports .TXT files. Command Command Function start Starts logging the network traffic. stop Stops logging network traffic. file Specifies the name of the file to which NDISLog information is stored. Save File Stores the file name.
Page 83: Owner
Owner Start > Settings > Control Panel > Owner Set the HX3 owner details. The Network ID is used when logging into a remote network. Setting Default Identification tab Name Blank Company Blank Address Blank Telephones Blank Display owner ID at power-on...
Page 84: Password
Password Start > Settings > Control Panel > Password Use this panel to set HX3 user access to control panels and power up password properties. Important: This password must be entered before performing a cold boot or cold reset. If entering a power-on or screen saver password does not allow you to disable this password protection or perform a cold boot, contact Customer Support.
Page 85: Pc Connection
• Tap the Change Connection button to change the direct connect setting. • Tap the drop-down box to view a list of pre-configured connection settings. Note: The HX3 only supports the USB connection. Do not change the connection type or the ability to connect with the HX3 may be lost.
Page 86: Power
Power Start > Settings > Control Panel > Power The HX3 power mode timers are cumulative. Because of the cumulative effect, if the Battery Power Scheme timers are set to 3 seconds, 15 seconds and 5 minutes: • The backlight turns off after 3 seconds of no activity, •...
Page 87 5 - 47...
Page 88: Regional And Language Settings
Regional and Language Settings Start > Settings > Control Panel > Regional Settings Set the appearance of numbers, currency, time and date based on regional and language settings. Set the HX3 user inter- face language and the default input language.
Page 89: Remove Programs
In some OS versions, this panel is replaced by the Installed Programs panel. The Installed Programs panel does not allow any user interaction. Select a program and tap Remove. Follow the prompts on the screen to uninstall HX3 user-installed only programs. The change takes effect immediately.
Page 90: System
System Start > Settings > Control Panel > System Use these HX3 panels to: • Review System and mobile device data and revision levels. • Adjust Storage and Program memory settings. • Assign a device name and device descriptor. Setting...
Page 91: Device Name Tab
The device name and description can be changed by the user. Enter the name and description using either the keypad or the Input Panel and tap OK to save the changes. This information is used to identify the HX3 to other computers and devices.
Page 92: Volume And Sounds
As the volume scrollbar is moved between Loud and Soft, the HX3 emits a tone each time the volume increases or decreases. Volume must be enabled when you want to adjust volume settings using keypad keys.
Page 93: Chapter 6 - Bluetooth Configuration
LXEConnect. The dialog pop-ups may be enabled for viewing with a remote management tool such as LXECon- nect. However, to preserve battery life, the dialog pop-ups should be turned off when the HX3 is not being viewed with a remote management utility.
Page 94 • It is not necessary to disconnect a paired scanner and printer before a different scanner or printer is paired with the HX3. • The target Bluetooth device should be as close as possible (up to 32.8 ft (10 meters) Line of Sight) to the HX3 during the pairing process.
Page 95: Bluetooth Devices Panel
Bluetooth Devices Panel Note: The HX3 does not have a touch screen. If the host computer has a touch screen, instructions using “tap” and “stylus” instead of “click” and “mouse” apply. Note: The Bluetooth Devices tab displays any device previously discovered and paired with the HX3.
Page 96: Bluetooth Device List
An icon with a red background indicates the device's Bluetooth connection is inactive. An icon with a white background indicates the device is connected to the HX3 and the device's Bluetooth connection is active. Double-tap a device in the list to open the device properties menu. The target device does not need to be active.
Page 97: Right Click Menu Options
Stop the connection between the HX3 and the highlighted paired Bluetooth device. Delete Remove an unpaired device from the Bluetooth device list. The highlighted device name and identifier is removed from the HX3 Bluetooth Devices panel after the user taps OK. Properties More information on the highlighted Bluetooth device.
Page 98: Bluetooth Properties Panel
Settings Panel Due to the headless design of the HX3, all Bluetooth dialog pop-up boxes are suppressed by default, even when the HX3 is viewed with LXEConnect. The dialog pop-ups may be enabled for viewing with a remote management tool such as LXE- Connect.
Page 99: Settings
Prompt if devices request to pair This option is Disabled by default. A dialog box appears on the HX3 screen notifying the user a Bluetooth device requests to pair with the HX3. The requesting Bluetooth device does not need to have been Discovered by the HX3 before the pairing request is received.
Page 100: Reconnect Panel
Reconnect Panel Due to the headless design of the HX3, all Bluetooth dialog pop-up boxes are suppressed by default, even when the HX3 is viewed with LXEConnect. The dialog pop-ups may be enabled for viewing with a remote management tool such as LXE- Connect.
Page 101: Auto Reconnect
This is an alphanumeric field displaying the currently selected Inbox. The Inbox is the location where files pushed to the HX3 from a remote client are stored. Use the browse button ... to browse to and select the Inbox folder.
Page 102: Enable Notifications
Enable Notifications When checked, the user is notified and may be prompted for a response when files are received by the HX3. When unchecked, inbound files are received with no notification to and no required action from the user. This option is enabled (checked) by default.
Page 103: About Panel
Bluetooth MAC address, and software version levels. The data cannot be edited by the user. Using Bluetooth ® The HX3 default Bluetooth setting is Enabled. The HX3 Bluetooth module is designed to Discover and pair with nearby Blue- tooth devices.
Page 104: Initial Configuration
LED on the device, or a dialog box is placed on the HX3 display. 14. Whenever the HX3 is turned On, all previously paired, live, Bluetooth devices in the vicinity are paired, one at a time, with the HX3.
Page 105: Bluetooth Indicators
• The mobile Bluetooth laser scanner / laser imager battery is fully charged. • The HX3 main battery is fully charged. Alternatively, the HX3 may be in a powered cradle or cabled to AC/DC power. • Important: The bar code numbering examples in this segment are not real and should not be created or scanned with a Bluetooth scanner.
Page 106: Hx3 With Label
7. The devices are paired. The Bluetooth mobile bar code reader responds with a series of beeps and an LED flashes. 8. After scanning the HX3 Bluetooth label, if there is no beep and no LED flash from the Bluetooth mobile device, the devices are currently paired.
Page 107: Bluetooth Beep And Led Indications
(page 14-1) for help with external Bluetooth devices. Bluetooth Printer Setup The Bluetooth managed device should be as close as possible, in direct line of sight, with the HX3 during the pairing pro- cess. 1. Open the LXEZ Pairing Panel.
Page 108: Using Opp
If a duplicate filename is received, LXEZ Pairing writes the file in the specified location, with an incremental number appended to the file name. For example, if a file named file.jpg is pushed to the HX3 and that filename already exists in the Inbox, LXEZ Pairing saves the new file as file001.jpg.
Page 109: Hx3 Pushes File To Remote Device
The file is pushed to the remote device and the user of the HX3 is notified of the completion of the push. Notifications disabled The file is pushed to the remote device and the user of the HX3 is not notified of the completion of the push. LXEZ Pairing and External Application...
Page 110 6 - 18...
Page 111: Chapter 7 - Bar Code Scanner Wedge
Return to Factory Default Settings When using any bar code reader to scan the Reset All (or equivalent) bar code with the HX3’s ring decoder, the next step is to open the Scanner applet on the HX3, click the OK button and then close it. This action will synchronize all scanner formats.
Page 112: Main Tab
Main Tab Port The ports are disabled until the HX3 auto-detects a device tethered to the port. Port 1 defaults to Bluetooth and Port 2 defaults to Ring when a Bluetooth enabled HX3 with ring scanner/imager is powered On. Output Default: Disabled.
Page 113: Enable Internal Scanner Sound
HX3 on the same data.
Page 114: Barcode Tab
Note: Do not scan decoder engine configuration bar codes in this guide when Continuous scan mode is on. Configuration bar codes do not decode when scanned while the HX3 is in Continuous Mode. Set the Timeout between same symbol to a value sufficient to prevent the beeper from continuously beeping when a sym- bol is left in the scanner’s field of view.
Page 115: Enable Code Id
If scan mode, power mode, or timeout between same symbol parameters are changed using external configuration bar codes in the later chapters of this guide the HX3 operating system automatically restores the parameters to their pro- grammed settings upon a warm or cold boot and/or any change made in the control panel.
Page 116: Name Text Box
When Enable Code ID is set to None, custom code IDs are ignored. Note: Custom symbologies will appear at the end of the list in the Symbology dialog, and are processed at the beginning of the list in the scanner driver itself. This allows custom IDs based on actual code IDs to be processed before the code ID itself.
Page 117: Remove
Remove The Clear All button text changes to a Remove button when an item in the Custom IDs list is selected. Click the desired line item and then click the Remove button to delete it. Line items are removed one at a time. Contents of the text box fields are cleared at the same time.
Page 118 Provided that the wedge is configured with the above table, below are examples of scanned bar code data and results of these manipulations. Bar Code Symbology Raw Scanner Data Resulting Data EAN-128 ]C11234567890123 bbb1234567890xxx EAN-128 ]C111234567890123 bbb11234567890xxx EAN-128 ]C1123 < rejected > (too short) EAN-13 ]E01234567890987 ccc]E04567890yyy...
Page 119: Bar Code - Ctrl Char Mapping
Bar Code - Ctrl Char Mapping The Ctrl Char Mapping button (Control Character Mapping) activates a dialog to define the operations the Wedge performs on control characters (values less than 0x20) embedded in bar codes. Control characters can be replaced with user- defined text which can include hat encoded or hex encoded values.
Page 120: List Box
(based on configurable Barcode Data) add a prefix or suffix to a bar code. The Symbology drop-down box contains all symbologies supported on the HX3. An asterisk appears in front of symbolo- gies that have already been configured or have been modified from the default value.
Page 121: Enable
Note: When All is selected in the Symbology field and the settings are changed, the settings in this dialog become the defaults, used unless overwritten by the settings for individual symbologies. This is also true for Custom IDs, where the code IDs to be stripped are specified by the user. Note: In Custom mode on the Barcode tab, any Code IDs not specified by the user will not be stripped, because they will not be recognized as Code IDs.
Page 122: Leading
If the total number of characters being stripped is greater than the number of characters in the bar code data, it becomes a zero byte data string. If, in addition, Strip Code ID is enabled, and no prefix or suffix is configured, the pro- cessing will return a zero-byte data packet, which will be rejected.
Page 123: Notes
Edit Double tap on the item to edit. Its values are copied to the text boxes for editing. The Add button changes to Replace. When Replace is tapped, the values for the current item in the list are updated. Clear All When no item in the Custom IDs list is selected, tapping the Clear All button clears the Custom ID list and any text written (and not yet added or inserted) in the Name and ID Code text boxes.
Page 124: Add Suffix
If ‘All’ is selected, the prefix is added for any symbology that has not been specifically configured. Add Suffix To enable a suffix, check the Suffix check box and enter the desired string in the text box. The default is disabled (unchecked) with a blank text string. When bar code data is processed, the Suffix string is sent to the output buffer after the bar code data.
Page 125 • c4 min length = 20, max length = 20, strip leading 0, strip trailing 4, Code ID enabled, Barcode Data = “00” Add the AIM custom symbologies. Refer to the previous section Bar Code – Symbology Settings for instruction. Click the Barcode Data button.
Page 126: Hat Encoding
Hat Encoding 7 - 16...
Page 127 7 - 17...
Page 128 7 - 18...
Page 129: Chapter 8 - Enabler Installation And Configuration
Although the HX3 has no display or alphanumeric keypad, HX3 control panels can be viewed and parameters manipulated using LXEConnect and ActiveSync on a connected host computer. The HX3 does not have a touch screen. If the host computer has a touch screen, instructions using “tap” and “stylus” instead of “click” and “mouse” apply.
Page 130: Enabler Uninstall Process
7. Reboot the HX3 if necessary. Update Monitoring Overview There are three methods by which the Enabler on the HX3 can communicate with the Mobile Device Server running on the host machine. • Wired via a serial cable between the Mobile Device Server PC and the HX3.
Page 131: Preparing A Device For Remote Management
RAM adjustment, real-time updates and Avalanche Enabler properties. If the RMU is not already installed on the HX3, see Using Wavelink Avalanche to Upgrade System Baseline. If in doubt, verify RMU.CE.CAB exists in the \Sys- tem folder. If the RMU.CE.CAB file is present when the Enabler is installed, the RMU is also installed. Important: If the OS package includes double-byte Asian fonts, the storage RAM property of the RMU must be higher than the default value (40MB).
Page 132: Version Information On Mobile Devices
Enabler Configuration Depending on the version of the Enabler running on the HX3, the desktop Enabler icon may look like one of the following: The available configuration options and tabs may vary by Enabler version. The examples shown in this section assume the latest version of the Enabler is installed on the HX3.
Page 133: File Menu Options
The default Settings password is system. The password is not case-sensitive. Avalanche Update using File > Settings Use these menu options to setup the Avalanche Enabler on the HX3. Change the settings and save them by rebooting before connecting to the network.
Page 134: Menu Options
Menu Options Note: Your HX3 screen display may not be exactly as shown in the following menu options. Connection (page 8-7) Enter the IP Address or host name of the Mobile Device Server. Set the order in which serial ports or RF connections are used to check for the presence of the Mobile Device Server.
Page 135: Connection
Connection Avalanche Server Address Enter the IP Address or host name of the Mobile Device Server assigned to the HX3. Check Serial Connection Indicates whether the Enabler should first check for serial port connection to the Mobile Device Server before checking for a wireless connection to the Mobile Device Server.
Page 136: Server Contact
On Resume – Connect to the Mobile Device Server when resuming from Suspend mode. On IP Change – Connect to the Mobile Device Server when the IP address of the HX3 changes. On Ext. Power – Initiate connection to the Mobile Device Server when the device is connected to an external power source, such as based on a docking event.
Page 137: Data
Specifies if the device sends statistics to the Mobile Device Server immediately following a connection to the server. Restrict Bandwidth to User Idle Time When enabled, periodic updates from the Mobile Device Server are postponed until the HX3 has been idle for the specified period of time. The default is disabled.
Page 138: Preferences
Preferences For best results, use AppLock for this function. AppLock is not available for the HX3. If the Preferences tab is not present on the Enabler installed on your device, see the equivalent options on the Startup/ Shutdown (page 8-21) tab.
Page 139: Display
• Info - Operational information is displayed in addition to those above. • Debug - The most detailed list is displayed. Display The user interface for the Enabler can be configured to dynamically change based on the status of the HX3 connection with the Mobile Device Server. At startup Default is Half Screen.
Page 140: Taskbar
Taskbar For best results, use AppLock for this function. AppLock is not available for the HX3. If the Taskbar tab is not present on the Enabler installed on your device, see the equivalent options on the Startup/ Shutdown (page 8-21) tab.
Page 141: Execution
Execution Note the dimmed options on this HX3 panel. This menu option is designed to manage downloaded applications for automatic execution upon startup. Auto-Execute Selection An application that has been installed with the Avalanche Management system can be run automatically following each boot.
Page 142: Scan Config
For best results, use eXpress Config and eXpress Scan for this function. eXpress Scan is included with the updated HX3 enablers. Scan Config functionality is a standard option of the Wavelink Avalanche MC system but is not currently supported on the HX3.
Page 143: Shortcuts
For best results, use AppLock for this function. AppLock is not available for the HX3. Configure shortcuts to other applications on the HX3. Shortcuts are viewed and activated in the Programs panel. This limits the user’s access to certain applications when the Enabler is controlling the mobile device display.
Page 144: Saas
SaaS Use to configure the Enabler to connect with Avalanche on Demand. This is a Software-as-a-Service version of Avalanche. Using either of the SaaS configuration options below assumes the user has registered with Wavelink. Disable SaaS No SaaS connection is used. Scan Configure SaaS Scan bar codes printed from within the Avalanche Console to configure the Enabler for the SaaS connection.
Page 145: Adapters
Current Adapter Lists all network adapters currently installed on the HX3. Primary Adapter Indicates if the Enabler is to attempt to configure the primary adapter (active only if there are multiple network adapters).
Page 146 Use Manual Settings When enabled, the Enabler will ignore any network or wireless settings coming from the Avalanche MC Console and use only the network settings on the HX3. Properties Icon Selecting the Properties icon displays the Manual Settings Properties dialog applet. From here, the user can configure Network, DNS and Wireless parameters using the displays shown below: Note: A reboot may be required after enabling or disabling these options.
Page 147 The Authentication tab may not be present in all versions of the Enabler. It is not recommend to enable “Manage Wireless Settings” for Summit Client devices. When you download a profile that is configured to manage network and wireless settings, the Enabler will not apply the manage network and wireless settings to the adapter unless the global Manage wireless settings and Manage network settings options are enabled on the Adapters panel.
Page 148: Status
It also searches for new adapters and may cause a slight delay to refresh the contents of the drop-down menu. Link speed indicates the speed at which the signal is being sent from the adapter to the HX3. Speed is dependent on signal strength.
Page 149: Startup/Shutdown
Startup/Shutdown For best results, use AppLock to manage the taskbar. AppLock is not available on the HX3. If the Startup/Shutdown tab is not present on the Enabler installed on your device, see the equivalent options on the Preferences (page 8-10) tab and the Taskbar (page 8-12) tab.
Page 150: Exit
Using eXpress Scan If the HX3 has an eXpress Scan icon on the desktop, eXpress Scan may be used for the initial configuration of the device. If the eXpress Scan icon is not present on the desktop, install the Enabler. If the icon is still not present, the Enabler must be updated.
Page 151: Step 2: Scan Bar Codes
Step 2: Scan Bar Codes For each mobile device to be configured, follow these instructions. 1. Start eXpress Scan on the HX3 by double clicking the eXpress Scan icon. 2. Enter the bar code password, if any. 3. Click Start.
Page 152: Step 3: Process Completion
Step 3: Process Completion After the last bar code is scanned, the settings are automatically applied. Once configured, the HX3 is warmbooted. Once connected to the wireless network and the Mobile Device Server, any software updates and additional configuration data are downloaded.
Page 153: Chapter 9 - Wireless Network Configuration
Although the HX3 has no display or alphanumeric keypad, HX3 control panels can be viewed and parameters manipulated using LXEConnect and ActiveSync on a connected host computer. Note: The HX3 does not have a touch screen. If the host computer has a touch screen, instructions using “tap” and “stylus” instead of “click” and “mouse” apply.
Page 154: Help
Help Help is available by clicking the ? icon in the title bar on most SCU screens. The SCU help may also be accessed by selecting Start > Help and tapping the Summit Client Utility link. The SCU does not have to be accessed to view the help information using this option.
Page 155: Main Tab
Main Tab Setting Default Admin Login SUMMIT Radio Enabled Active Config/Profile Default Regulatory Domain FCC or ETSI The Main tab displays information about the wireless client device including: • SCU (Summit Client Utility) version • Driver version • Radio Type (BG is an 802.11 b/g radio, ABG is an 802.11 a/b/g radio). •...
Page 156: Auto Profile
Auto Profile Auto Profile allows the user to configure a list of profiles that the SCU can search when a radio connection is lost. After using the Profile tab to create any desired profiles, return to the Main tab. To specify which profiles are to be included in Auto Profile, click the List button.
Page 157: Profile Tab
• Turn the radio on or off on the Main tab. • Select an active Profile on the Main tab. • View the current parameter settings for the profiles on the Profile Tab (page 9-5). • View the global parameter settings on the Global Tab (page 9-11).
Page 158 Credentials Allows entry of a username and password, certificate names, and other information required to authenticate with the access point. The information required depends on the EAP type. Delete Deletes the profile. The current active profile cannot be deleted and an error message is displayed if a delete is attempted.
Page 159: Profile Parameters
Options are: None, WEP (or Manual WEP), WEP EAP (or Auto WEP), WPA PSK, WPA TKIP, WPA CCKM, WPA2 PSK, WPA2 AES, or WPA2 CCKM. CKIP is not supported in the HX3. The Encryption type chosen determines if the WEP Keys / PSK Keys button is active and also determines the available entries in the WEP or PSK pop-up window.
Page 160 Radio Mode parameter correspond to the AP to which the device is to connect. For example, if this parameter is set to G rates only, the HX3 may only connect to APs set for G rates and not those set for B and G rates.
Page 161: Status Tab
Status Tab This screen provides information on the radio: • The profile being used. • The status of the radio card (down, associated, authenticated, etc.). • Client information including device name, IP address and MAC address. • Information about the Access Point (AP) maintaining the connection to the network including AP name, IP address and MAC address.
Page 162: Diags Tab
Diags Tab The Diags screen can be used for troubleshooting network traffic and radio connectivity issues. (Re)connect Use this button to apply (or reapply) the current profile and attempt to associate or authenticate to the wireless LAN. All activity is logged in the Diagnostic Output box on the lower part of the screen. Release/Renew Obtain a new IP address through release and renew.
Page 163: Global Tab
Global Tab The parameters on this panel can only be changed when an Admin is logged in with a password. The current values for the parameters can be viewed by the general user without requiring a password. Note: Tap the Commit button to save changes. If the panel is exited before tapping the Commit button, changes are not saved! Setting Default...
Page 164: Custom Parameter Option
Custom Parameter Option Honeywell does not support the parameter Custom option. The parameter value is displayed as “Custom” when the operating system registry has been edited to set the Summit parameter to a value that is not available from the parameter’s drop down list.
Page 165 Parameter Default Description Ad Hoc Channel Use this parameter when the Radio Mode profile parameter is set to Ad Hoc. Specifies the channel to be used for an Ad Hoc connection to another client device. If a channel is selected that is not supported by the by the radio, the default value is used.
Page 166 Antenna Configuration: BG Main and BG Aux. TX Diversity: On. Contact Customer Support (page 14-1) if you have questions about the antenna(s) installed in your HX3. RX Diversity BG: On-Start How to handle antenna diversity when receiving packets from the Access on Main Point.
Page 167 Parameter Default Description Auth Timeout 8 seconds Specifies the number of seconds the Summit software waits for an EAP authentication request to succeed or fail. If the authentication credentials are stored in the active profile and the authentication times out, the association fails. No error message or prompting for corrected credentials is displayed.
Page 168: Sign-On Vs. Stored Credentials
Sign-On vs. Stored Credentials When using wireless security that requires a user name and password to be entered, the Summit Client Utility offers these choices: • The Username and Password may be entered on the Credentials screen. If this method is selected, anyone using the device can access the network.
Page 169 10. Verify the device is authenticated by reviewing the Status tab. When the device is property configured, the Status Tab indicates the device is Authenticated and the method used. 11. The sign-on screen is displayed after a reboot. 12. If a user enters invalid credentials and clicks OK, the device associates but does not authenticate. The user is again prompted to enter credentials.
Page 170: Windows Certificate Store Vs. Certs Path
Windows Certificate Store vs. Certs Path Note: It is important that all dates are correct on the HX3 and host computers when using any type of certificate. Certificates are date sensitive and if the date is not correct authentication will fail.
Page 171: Configuring The Profile
Configuring the Profile Use the instructions in this section to complete the entries on the Profile tab according to the type of wireless security used by your network. The instructions that follow are the minimum required to successfully connect to a network. Your system may require more parameters than are listed in these instructions.
Page 172: Wep
To connect using WEP, make sure the following profile options are used. Enter the SSID of the Access Point assigned to this profile. 9. Set EAP Type to None. 10. Set Encryption to WEP or Manual WEP (depending on SCU version). 11.
Page 173: Leap
LEAP To use LEAP (without WPA), make sure the following profile options are used. Enter the SSID of the Access Point assigned to this profile. 16. Set EAP Type to LEAP. 17. Set Encryption to WEP EAP or Auto WEP (depending on SCU version). 18.
Page 174: Peap/Mschap
PEAP/MSCHAP Note: The date must be properly set on the device to authenticate a certificate. To use PEAP/MSCHAP, make sure the following profile options are used. 1. Enter the SSID of the Access Point assigned to this profile. 2. Set EAP Type to PEAP-MSCHAP. 3.
Page 175 15. Return to the Credentials screen and check the Validate server check box. If using the Windows certificate store: 1. Check the Use MS store check box. The default is to use the Full Trusted Store. 2. To select an individual certificate, click on the Browse button. 3.
Page 176: Peap/Gtc
PEAP/GTC Note: The date must be properly set on the device to authenticate a certificate. To use PEAP/GTC, make sure the following profile options are used. 1. Enter the SSID of the Access Point assigned to this profile. 2. Set EAP Type to PEAP-GTC. 3.
Page 177 15. Return to the Credentials screen and check the Validate server check box. Note: Some servers may be configured to allow only a single use of the password for PEAP/GTC. In this case, wait for the token to update with a new password before attempting to validate the server. Then enter the new password, check the Validate Server check box and proceed with the certificate process below.
Page 178: Wpa/Leap
WPA/LEAP To use WPA/LEAP, make sure the following profile options are used. 1. Enter the SSID of the Access Point assigned to this profile. 2. Set EAP Type to LEAP. 3. Set Encryption to WPA TKIP. 4. Set Auth Type as follows: •...
Page 179: Eap-Fast
RADIUS server. The RADIUS server must have auto provisioning enabled to send the PAC provisioning credentials to the For automatic PAC provisioning, once a username/password is authenticated, the PAC information is stored on the HX3. The same username/password must be used to authenticate each time. See the note below for more details.
Page 180 10. To use Sign-On credentials: • Do not enter a User and Password as the user will be prompted for the Username and Password when connecting to the network. 11. To use Stored Credentials: • Enter the Domain\Username (if the Domain is required), otherwise enter the Username. •...
Page 181: Eap-Tls
EAP-TLS Note: The date must be properly set on the device to authenticate a certificate. To use EAP-TLS, make sure the following profile options are used. 1. Enter the SSID of the Access Point assigned to this profile. 2. Set EAP Type to EAP-TLS. 3.
Page 182 3. Click OK then click Commit. The HX3 should be authenticating the server certificate and using EAP-TLS for the user authentication. Ensure the correct Active Profile is selected on the Main tab and warmboot. The SCU Main tab shows the device is associated after the radio connects to the network.
Page 183: Wpa Psk
WPA PSK To connect using WPA/PSK, make sure the following profile options are used: 1. Enter the SSID of the Access Point assigned to this profile. 2. Set EAP Type to None. 3. Set Encryption to WPA PSK or WPA2 PSK. 4.
Page 184: Certificates
Note: Refer to the Security Primer (available on the Honeywell web site) to prepare the Authentication Server and Access Point for communication. Note: It is important that all dates are correct on the HX3 and host computers when using any type of certificate. Certificates are date sensitive and if the date is not correct authentication will fail.
Page 185 3. Click the Download a CA certificate, certificate chain or CRL link. 4. Make sure the correct root CA certificate is selected in the list box. 9 - 33...
Page 186 6. To download the CA certificate, click on the Download CA certificate link. 7. Click the Save button and save the certificate. Make sure to keep track of the name and location of the certificate. 8. Install the certificate on the HX3. 9 - 34...
Page 187: Installing A Root Ca Certificate
Note: This section is only if the Windows certificate store is used. If the certificate store is not used, copy the certificate to the \System folder or other path specified in the Summit Certs global parameter. 1. Copy the certificate file to the HX3. Import the certificate by navigating to Start > Control Panel > Certificates. 2. Tap the Import button.
Page 188: Generating A User Certificate
Sign into the CA with the username and password of the person who will be logging into the mobile device. 8. This process saves a user certificate and a separate private key file. Windows CE equipped devices such as the HX3 require the private key to be saved as a separate file rather than including the private key in the user certificate.
Page 189 9. Click the Request a certificate link. 10. Click on the advanced certificate request link. 9 - 37...
Page 190 11. Click on the Create and submit a request to this CA link. 9 - 38...
Page 191 12. For the Certificate Template, select User. 13. Check the Mark keys as exportable and the Export keys to file check boxes. 14. Type the full path on the local PC where the private key is to be copied. Also specify the private key filename. 9 - 39...
Page 192 15. Be sure to note the name used for the private key file, for example USER.PVK. The certificate file created later in this process must be given the same name, for example, USER.CER. 16. DO NOT check to use strong private key protection. 17.
Page 193: Installing A User Certificate
USER.PVK then the certificate file created must be given the same name, for example, USER.CER. 23. Install the user certificate. Installing a User Certificate 1. Copy the certificate and private key files to the HX3. 2. Import the certificate by navigating to Start > Control Panel > Certificates. 9 - 41...
Page 194 3. Select My Certificates from the pull down list. 4. Tap the Import button. 5. Make sure From a File is selected and tap OK. 6. Using the explorer buttons, browse to the location where you copied the certificate. 7. Select the certificate desired and tap OK. 8.
Page 195 9. With the certificate you just imported highlighted, tap View. 10. From the Field pull down menu, select Private Key. • If the private key is present, the process is complete. • If the private key is not present, import the private key. 11.
Page 196: Verify Installation
Verify Installation Tap on View to see the certificate details again. The private key should now say present. If it does not, there is a problem. Possible items to check: Note: Make sure the certificate was generated with a separate private key file, as shown earlier in this section. If the certificate was not generated with a separate private key file, generate a new certificate and follow the import process again.
Page 197: Chapter 10 - Keymap
5 Key Keypad The HX3 keypad is designed for use with voice applications. Because of the limited design, the HX3 should be connected via ActiveSync to a host computer running LXEConnect when a full keyboard is needed (for example, during system configuration).
Page 198 10 - 2...
Page 199: Chapter 11 - Desktop Cradle
• and enable serial communication with USB devices (host, client, and other USB cabled devices). The HX3 cradle is available with or without a power cord. If ordered without a power cord, a C14 style power cord is required. Communications cables for the HX3 are available separately.
Page 200: Components
7. Insert the tethered battery in one of the battery charging bays at the back of the cradle. The battery can remain tethered as the power connection between the battery and the HX3 is broken as soon as the HX3 connects to the power source via the cradle-power connector.
Page 201: Bottom View
Bottom View The HX3 Cradle Connector is located on the bottom of device. Rechargeable Lithium Ion Battery Pack Each battery pack has one side alignment rib wider than the other to ensure the battery pack is inserted in the battery charging bay easily.
Page 202: Desktop Cradle Footprint
Desktop Cradle Footprint Approximations 1. 5.5 in / 14 cm 2. 2.0 in / 5.1 cm 3. 2.0 in / 5.1 cm 4. 0.45 in / 1.14 cm 5. 5.5 in / 14 cm 6. 6.0 in / 15.2 cm 7.
Page 203: Connecting Input/Output Cables
Each time the HX3 is docked in the powered cradle, the connection between the tethered battery and the HX3 terminates. Press the Power button on the HX3 and the PWR LED on the cradle will illuminate. When a battery is in either one (or both) of the battery charging bays, the battery charging bay LED (B1 / B2) is illuminated.
Page 204: Serial Cable
Serial Cable Note: Only approved Honeywell cables are to be used for serial communication between the cradle and external devices. Note: The serial cable port is located on the back of the desktop cradle. Note: Assemble the AC Adapter and connect it to the desktop cradle. Verify the cradle has a dependable power source.
Page 205: Cradle Pwr Led
The HX3 can be inserted and removed with one hand, or if preferred, two hands. Do not "slam" or slide the HX3 sideways into the cradle. Do not rock the HX3 forward out of the cradle. Damage may result. 1. Fingertip Depression 2.
Page 206: Docking The Hx3
(fasteners, screwdrivers, etc., not supplied by Honeywell). Docked HX3 Mode States When the HX3 is not docked in a powered cradle it can be set to enter Suspend Mode using Start > Settings > Control Panel > Power > Schemes tab.
Page 207: Inserting And Removing A Tethered Battery
A fully depleted Extended battery recharges fully in approximately eight hours in a powered cradle charging pocket. The HX3 tether connector must be at the top of the battery in the charging bay. The battery will not fit properly into the charging pocket if the tether connector is inserted into the depression of the charging bay.
Page 208: Cradle Help
Do not use paper towels or harsh-chemical-based cleaning fluids since they may result in damage to the surfaces and/or battery charging terminals (pins). Use a clean soft cloth to wipe any dirt, moisture or grease from the HX3, spare battery packs, charging contacts (pins) or the cradle.
Page 209: Chapter 12 - Battery Charger
This device cannot charge/recharge coin cell batteries sealed inside the HX3, if any. Note: The HX2 and HX3 use the same batteries. Batteries used by the HX3 body worn Voice device are charged, recharged and analyzed in the HX2 labeled battery charger.
Page 210: Cautions And Warnings
• Do not store the Li-Ion battery pack in direct sunlight or anywhere the battery pack cannot cool down. • If the Li-Ion battery pack is hot after removal from the HX3, allow it to cool at room temperature or in a cool air stream before placing it in the charger.
Page 211: Components
Components Battery Charger 1. Front 2. Battery Charging Pocket 3. Battery Charge LED Indicator 4. Analyze Pocket >90% >80% 5. Analyze LED >70% 6. Analyze Dome Switch >50% 7. Analyze Progress LEDs ANALYZE 8. AC/DC Power Connector Battery Charging Pocket 1.
Page 212: Installation
Installation Assemble the Power Supply Note: Assemble the AC adapter for the Battery Charger before connecting it to the charger. The AC power supply for the battery charger is shipped with the battery charger unless you require a country-specific power supply and cable assembly. The battery charger power supply is intended for use with the battery charger only.
Page 213: Charging Batteries
Use the charge function to return the HX3 battery pack to its maximum available power capacity. Use the analyze function to compare the battery pack’s maximum available capacity to the specified capacity. This allows you to determine the battery pack’s power loss due to age.
Page 214: Inserting A Battery Into The Charging Pocket
Inserting a Battery into the Charging Pocket Caution! It is important that battery packs are inserted into the charging pocket correctly. Inserting the battery incorrectly could result in damage to the battery pack or the charger. Caution! Do not “slam” the battery pack into the charging pocket. Damage may result. When preparing the battery pack for insertion into the battery charging pocket, hold the battery with the battery charging contacts in line with the charging contacts in the charging pocket.
Page 215: Interpreting The Charging Pocket Leds
Interpreting the Charging Pocket LEDs The status of the charge operation is indicated by the color of the LED for each charging pocket. RED Continuous - on any charge pocket Continuous red means the battery pack is charging. • RED FLASHING - on any charge pocket •...
Page 216: Using The Charge/Analyze Pocket
Using the Charge/Analyze Pocket 1. Analyze/Charge Percentage of Original value 2. Analyze Dome switch 3. Analyze/Charge Pocket LED The analyze/charge pocket is the one closest to the battery charger label and the Analyze dome switch. The analyze/charge pocket can be used to: •...
Page 217: Battery Charger Help
Issue Cause Solution Battery pack does not fit in Different manufacturer's battery Check if the HX3 battery pack has Honeywell part charging pocket. pack, or there is an object in the number HX2A301BATTSTD /160289-0001 or charging pocket. HX2A302BATTEXT/160320-0001 on the label. If not, do not use.
Page 218: Maintenance
Issue Cause Solution Solid YELLOW / AMBER LED The battery pack is too hot or too Remove battery pack from the charging pocket and when battery pack is inserted cold to charge. allow it to adjust to room temperature. in the charging pocket. If the battery pack is left in the charging pocket, it will cool down or warm to a temperature upon which the charger will begin the charge cycle.
Page 219 There are no user serviceable parts in the Lithium Ion Battery Pack. Contact Customer Support (page 14-1) for battery disposal and replacement options. 12 - 11...
Page 220 12 - 12...
Page 221: Chapter 13 - Specifications And Reference Material
4.98 in | 12.55 cm Height 1.40 in | 3.56 cm Weight 1 lb 0.5 oz | 462 g HX3 with network card, standard battery and ring scanner Battery Standard 4.1 oz | 116 g Battery Extended 7.2 oz | 205 g Ring Scanner 1.7 oz | 48 g...
Page 222: Network Card Specifications
32° F to 104° F / 0° C to 40° C (charger On, no charging in progress) Charging 50° F to 104° F / 10° C to 40° C (Battery charger is charging and/or HX3 is receiving power through cradle connection) Storage -14°...
Page 223: Battery Charger
Battery Charger The battery charger is designed to charge / re-charge standard and extended batteries. Life Cycle: 500 charge/discharge cycles. Electrical Battery packs may leak up to 1mA current through the battery contacts when left in an unpowered battery charger charging pocket.
Page 224 Full ASCII Code 39 Scan Value Hex Value Keystroke Encode Char. 1011 CTRL K 1012 CTRL L 1013 CTRL M 1014 CTRL N 1015 CTRL O 1016 CTRL P 1017 CTRL Q 1018 CTRL R 1019 CTRL S 1020 CTRL T 1021 CTRL U 1022...
Page 225 Full ASCII Code 39 Scan Value Hex Value Keystroke Encode Char. 1054 1055 1056 1057 1058 1059 1060 < 1061 1062 > 1063 1064 1065 1066 1067 1068 1069 1070 1071 1072 1073 1074 1075 1076 1077 1078 1079 1080 1081 1082 1083...
Page 226 Full ASCII Code 39 Scan Value Hex Value Keystroke Encode Char. 1097 1098 1099 1100 1101 1102 1103 1104 1105 1106 1107 1108 1109 1110 1111 1112 1113 1114 1115 1116 1117 1118 1119 1120 1121 1122 1123 1124 1125 1126 1127 Undefined...
Page 227: Chapter 14 - Customer Support
Limited Warranty Honeywell International Inc. (“HII”) warrants its products to be free from defects in materials and workmanship and to conform to HII’s published specifications applicable to the products purchased at the time of shipment. This warranty does not cover any HII product which is (i) improperly installed or used;...
Page 228: Limited Warranty Duration
These warranties are non-transferable. Limited Warranty Duration Note: The HX3 is docked in a HX2-labeled Desktop Cradle. HX3 batteries are re-charged using a HX2-labeled cradle and a HX2-labeled Battery Charger. The duration of the limited warranty for the HX3 is 1 year.
Page 230 Honeywell Scanning & Mobility 9680 Old Bailes Road Fort Mill, SC 29707 www.honeywellaidc.com ™ ECN 2015-618 HX3-UG Rev A 2/15...

Honeywell HX3 User Manual

Chapter 1 - HX3 Agency Compliance

Chapter 2 - Getting Started

Chapter 3 - Hardware Configuration

Chapter 4 - Power Modes and Batteries

Chapter 5 - Software Configuration

Chapter 6 - Bluetooth Configuration

Chapter 7 - Bar Code Scanner Wedge

Quick Links

Related Manuals for Honeywell HX3

Summary of Contents for Honeywell HX3