Also See for Honeywell HX3
Related Manuals for Honeywell HX3
-
Handhelds Honeywell HX3 Quick Start Manual
Wearable computer with microsoft windows ce 5.0 operating system (16 pages)
-
Handhelds Honeywell HX2 Reference Manual
(310 pages)
-
Handhelds Honeywell HX2 User Manual
Microsoft windows ce 5 operating system (48 pages)
-
Handhelds Honeywell HX2 Quick Start Manual
(16 pages)
-
Computer Hardware Honeywell RS-485 Installation Manual
Adapter board (18 pages)
-
Computer Hardware Honeywell NX series User Manual
Nx series constant and variable torque variable speed drives for induction motors (86 pages)
-
Computer Hardware Honeywell RM7838B Installation Instructions Manual
7800 series relay module (20 pages)
-
Controller Honeywell UDC3300 User Manual
Universal digital controller (118 pages)
Summary of Contents for Honeywell HX3
-
Page 1
Wearable Computer Microsoft® Windows® CE 5 Operating System Cradle Reference Guide...
-
Page 2: Limited Warranty
Disclaimer Honeywell International Inc. (“HII”) reserves the right to make changes in specifications and other information contained in this document without prior notice, and the reader should in all cases consult HII to determine whether any such changes have been made. The information in this publication does not represent a commitment on the part of HII.
-
Page 3
Keep dirt and foreign objects out of the battery pocket. Do not short circuit any of the contacts in the battery pocket, this could result in injury or property damage. Do not operate the Desktop Cradle if it has been dropped or damaged in any way. Return the Desktop Cradle to Honeywell. Storing the HX2 Desktop Cradle Disconnect Desktop Cradle from the AC power source by pulling the plug;...
-
Page 4
Do not operate the Desktop Cradle with a damaged AC cord or plug. Honeywell does not recommend the use of any extension cord with the HX2 Desktop Cradle.
-
Page 5: Table Of Contents
Indicators Cradle LEDs 2-10 Cradle PWR LED 2-10 B1 and B2 LED 2-10 How to Dock or Remove the HX3 2-11 Insert the HX3 into the cradle 2-11 Remove the HX3 from the bay 2-12 Docked HX3 Mode States 2-12...
-
Page 7: Chapter 1: Introduction
HX3 while the HX3 is docked. The HX3 can be either On or in Suspend Mode while in the cradle. Power must be applied to the cradle before any battery bay or docking bay charging can commence.
-
Page 9: Chapter 2: Desktop Cradle
Make sure the items in the carton match your order. Save the shipping container for later storage or shipping. The HX3 cradle is available with or without a power cord. If ordered without a power cord, a country specific C14 style power cord is required.
-
Page 10: Preparing The Cradle For Use
Preparing the Cradle for Use Note: Keep dirt and foreign objects out of the cradle. Do not short circuit any of the charging terminals (pins), as this action could result in injury or property damage. Use a stable, horizontal surface out of the way of: inclement weather conditions, extremely high concentrations of dust or wind blown debris, accidental knocks, bumps or other shocks to the cradle and items in the cradle bays.
-
Page 11: Components
The HX2 Cradle is not certified for use in Hazardous Locations. Note: The HX3 Voice mobile device can be docked in the HX2 labeled Cradle. The HX3 tethered battery can be recharged in a powered HX2 labeled Cradle battery charging pocket.
-
Page 12: Hx3 Rechargeable Lithium Ion Battery Pack
HX3 Rechargeable Lithium Ion Battery Pack Each battery pack has one side alignment rib wider than the other to ensure the battery pack is inserted in the battery charging bay easily. This design ensures the battery charging terminals line up with the charging terminals in each charging bay.
-
Page 13: Cradle Footprint
6. 6.0 in / 15.2 cm 7. 2.5 in / 6.3 cm Cradle Height: 3.4 in / 8.6 cm Cradle w/HX3 Height: 4.75 in / 12.1 cm Cradle w/Tethered Battery Height: 6 in / 15 cm Bottom View – Measurements are Not to Scale Table Mounting The cradle can be mounted to a flat, stable surface using the <1mm hole in the Tethered Ring Scanner storage bay (fasteners,...
-
Page 14: Power Cable
AC/DC power adapter and the cradle. Each time the HX3 is docked in the powered cradle, the connection between the tethered battery and the HX3 terminates. Press the Power button on the HX3 and the PWR LED on the cradle will illuminate.
-
Page 15: Connect Input/output Cables
Note: Route all cables to ensure they are protected from jostling, tugging or being disconnected by passing objects. The cradle must be receiving power from an external power source before HX3 battery charging can begin. USB Cable Prerequisite: The steps outlined in...
-
Page 16: Serial Cable
Prerequisite: The steps outlined in Power Cable have been completed and the cradle has a dependable power source. The serial cable port is located on the back of the cradle. Only approved Honeywell cables are to be used for serial communication between the cradle and external devices.
-
Page 17: Indicators
1 B1 LED – Back left battery charging bay listed in Cradle LEDs. PWR LED - HX3 docked / on / receiving Normal State – Off. With HX3 in, turned On and AC power, normal state is On. power bay B2 LED – Back right battery charging Normal State –...
-
Page 18: Cradle Leds
HX3 is not properly seated in charging bay and/or if this is the first time the HX3 has been inserted, the HX3 is properly seated and has not been powered On. HX3 is On, is properly seated in the charging bay and is receiving external power through Green the cradle.
-
Page 19: How To Dock Or Remove The Hx3
The HX3 can be inserted and removed with one hand, or if preferred, two hands. Do not "slam" or slide the HX3 sideways into the cradle. Do not rock the HX3 forward out of the cradle. Damage may result. 1. Fingertip Depression 2.
-
Page 20: Remove The Hx3 From The Bay
HX2 desktop cradle to a flat, stable surface (fasteners, screwdrivers, etc., not supplied by Honeywell). Docked HX3 Mode States When the HX3 is not docked in a powered cradle it can be set to enter Suspend Mode using Start > Settings > Control Panel > Power > Schemes tab or Start > Suspend.
-
Page 21: How To Insert/remove A Hx3 Tethered Battery
A fully depleted Extended battery recharges fully in approximately eight hours in a powered cradle charging pocket. The HX3 tether connector must be at the top of the battery in the charging pocket. The battery will not fit properly into the charging pocket if the tether connector is inserted into the depression of the charging pocket.
-
Page 22: Cradle Help
Do not use paper towels or harsh-chemical-based cleaning fluids since they may result in damage to the surfaces and/or battery charging terminals (pins). Use a clean soft cloth to wipe any dirt, moisture or grease from the HX3, spare battery packs, charging contacts (pins) or the cradle.
-
Page 23: Technical Specifications - Desktop Cradle
32° F to 104° F / 0° C to 40° C (charger On, no charging in progress) 50° F to 104° F / 10° C to 40° C (Battery charger is charging and/or HX3 is receiving power through cradle con-...
-
Page 24
2-16...
-
Page 25: Chapter 3: Technical Assistance
Limited Warranty Honeywell International Inc. ("HII") warrants its products to be free from defects in materials and workmanship and to conform to HII’s published specifications applicable to the products purchased at the time of shipment. This warranty does not cover any HII product which is (i) improperly installed or used;...
-
Page 26
The duration of the limited warranty for the HX3 Battery Charger is 1 year. The duration of the limited warranty for the HX3 2000mAh Li-Ion and 4000mAh Li-Ion Battery is 6 months. The duration of the limited warranty for the HX3 Ring Scanner and Ring Imager is 1 year.
-
Page 28
Honeywell Scanning & Mobility 9680 Old Bailes Road Fort Mill, SC 29707 www.honeywellaidc.com E-EQ-HX3OGWW Rev E 10/12...
Comments to this Manuals
Latest comments: