Toshiba e-studio600 Service Manual page 31

Error code Classification
E752 RADF jam
E761
E762
E763
E764
E765
E766
E767
E768
E800
E860
E870
E9F0 Finisher jam
(Puncher section)
EA10 Finisher jam
(Finisher section)
EA20
EA30
EA40
EA50
EA60
EA80 Finisher jam
(Saddle Stitcher sec-
tion)
EA90
EAA0
EAB0
EAC0
EAD0 Other paper jam
March 2005 © TOSHIBA TEC
Contents
Original not reaching original intermediate transport
sensor: The leading edge of the original which has
passed the read sensor does not reach the original
intermediate transport sensor.
Original remaining at original length detection sen-
sor
Original remaining at original registration sensor
Original remaining at original width detection sen-
sor
Original remaining at read sensor
Original remaining at original intermediate transport
sensor
Original remaining at small original reverse sensor
Original remaining at small original exit sensor
Original remaining at large original exit sensor
24 VDC supply off jam: A job is started or continued
while 24 VDC supply is shut off.
Jam access cover open jam: The jam access cover
has opened during the operation of the RADF.
RADF open jam: The RADF has opened during the
operation of the RADF.
Hole punch jam: Hole punching is not performed
properly.
Paper transport delay jam: Paper which has passed
the exit sensor does not reach the inlet sensor.
Paper transport stop jam: Paper which has reached
the inlet sensor does not pass the inlet sensor.
Power-ON jam: Paper is remaining at the inlet sen-
sor when the power is turned ON.
Door open jam: The upper cover or the front cover
of the Finisher has opened, or the upper door or the
front door of the Hole Punch Unit has opened dur-
ing printing.
Stapling jam: Stapling is not performed properly.
Early arrival jam: The inlet sensor detects paper
earlier than the specified timing.
Stapling jam: Stapling is not performed properly.
Door open jam: The delivery cover or the inlet cover
has opened during printing.
Power-ON jam: Paper is remaining at the No. 1
paper sensor, No. 2 paper sensor, No. 3 paper sen-
sor, vertical path paper sensor or delivery sensor
when the power is turned ON.
Paper transport stop jam: Paper which has passed
the inlet sensor does not reach or pass the No. 1
paper sensor, No. 2 paper sensor, No. 3 paper sen-
sor or delivery sensor.
Transport delay jam: Paper which has reached the
inlet sensor does not pass the inlet sensor.
Print end command time-out jam: The printing has
not finished normally due to the communication
error between the SYS board and LGC board at the
end of the printing.
e-STUDIO520/600/720/850 ERROR CODE AND SELF-DIAGNOSTIC MODE
2 - 7
Troubleshooting
Ch.5.1.4
Ch.5.1.4
Ch.5.1.4
Ch.5.1.4
Ch.5.1.4
Ch.5.1.4
Ch.5.1.4
Ch.5.1.4
Ch.5.1.4
Ch.5.1.4
Ch.5.1.4
Ch.5.1.4
Ch.5.1.5 [ 1 ]
Ch.5.1.5 [ 2 ]
Ch.5.1.5 [ 2 ]
Ch.5.1.5 [ 2 ]
Ch.5.1.5 [ 2 ]
Ch.5.1.5 [ 2 ]
Ch.5.1.5 [ 2 ]
Ch.5.1.5 [ 3 ]
Ch.5.1.5 [ 3 ]
Ch.5.1.5 [ 3 ]
Ch.5.1.5 [ 3 ]
Ch.5.1.5 [ 3 ]
Ch.5.1.5 [ 5 ]
2