JRC JSS-2150 Instruction Manual page 87

1 0 .
1 0 .
1 0 .
Press the CANCEL
The alarm stops and the screen shown at
right is displayed.
1 1 .
1 1 .
1 1 .
Press ENT.
The status display shown at right, with
communication frequencies set, is displayed
and the routine call is completed. Start
communications using the handset.
The popup screen shown at the right
Note
(bottom) appears if the antenna tuning
that started in step 9 above is not
finished yet.
- After completing the routine individual call where the ARQ or FEC is specified,
Note
the telex mode is set to the equipment. Then the telex communication can be
started with the data terminal.
- If the MMSI of the coast station is input at Address, the following display and
functions are available.
- If the objective station is unable to comply with the call, own station (caller)
may receive one of the following acknowledgements may be received. (* are
coast stations only) In this case, wait and retry the call again later, if possible,
according to the message.
No reason/ No reason.
Congestion/ The maritime information
exchange center is congested.
Busy/ Busy.
Queue/ The call has been queued.
Barred/ The station is closed.
key or ENT.
The initial call frequencies are TX 2189.5 kHz and Rx 2177 kHz.
Frequencies can also be selected from among international frequencies
by using the numeric keypad or the jog dial. For details, see "11.3
International DSC frequencies for routine calls".
The working frequency is specified by the coast station so Working FRQ
is not displayed.
*
*
I D 4 3 1 0 0 1 2 3 4
P o s 8 9 ﾟ 5 9 . 0 1 2 3 ' N
1 7 9 ﾟ 5 9 . 6 7 8 9 ' E @ 0 0 : 0 0
T E L R x : 2 0 6 5 . 0 / T x : 2 0 6 5 . 0 k H z
R e c e i v e d r o u t i n e m e s s a g e
T y p e
F r o m
M o d e
W o r k F R Q
E O S
R x F R Q
[ C o n t i n u e ] [ C o n t i n u e ]
I D 4 3 1 0 0 1 2 3 4
P o s 8 9 ﾟ 5 9 . 0 1 2 3 ' N
1 7 9 ﾟ 5 9 . 6 7 8 9 ' E @ 0 0 : 0 0
TEL
2065.0
RX
2065.0
TX
S I G
W K R s c a n b a n d s :
2 4 6 8 1 2 1 6 ( M H z )
I D 4 3 1 0 0 1 2 3 4
P o s 8 9 ﾟ 5 9 . 0 1 2 3 ' N
1 7 9 ﾟ 5 9 . 6 7 8 9 ' E @ 0 0 : 0 0
T E L R x : 2 0 6 5 . 0 / T x : 2 0 6 5 . 0 k H z
R e c e i v e d r o u t i n e m e s s a g e
T y p e
- A t t e n t i o n -
F r o m
M o d e
T u n i n g t h e a n t e n n a t o
W o r k F R Q
t h e f r e q u e n c y n o w .
W a i t a m o m e n t , p l e a s e .
E O S
R x F R Q
[ C o n t i n u e ]
[ C o n t i n u e ]
No operator/
Operator is not present.
Temp no operator/
The operator is temporarily away.
EQP disabled/
The equipment has been disabled.
Unable FRQ/
The proposed frequency cannot be used.
Unable mode/
The proposed mode cannot be used.
Operation
T I M E 0 0 : 0 0 ( U T C )
( E X T )
: I n d i v i d u a l A C K
: 4 3 1 1 2 3 4 5 6
: R a d i o t e l e p h o n e
: T x 2 0 6 5 . 0 k H z
R x 2 0 6 5 . 0 k H z
: A C K B Q
: 2 1 6 9 . 0 k H z
[ C a n c e l ]
T I M E 0 0 : 0 0 ( U T C )
( E X T )
kHz
kHz
T I M E 0 0 : 0 0 ( U T C )
( E X T )
T x T
: I n d i v i d u a l A C K
: 4 3 1 1 2 3 4 5 6
: R a d i o t e l e p h o n e
: T x 2 0 6 5 . 0 k H z
R x 2 0 6 5 . 0 k H z
: A C K B Q
: 2 1 6 9 . 0 k H z
[ C a n c e l ]
4-37