Page 1: Axis 5570E
AXIS 5570e/AXIS 5670e User’s Manual AXIS 5570e AXIS 5670e User’s Manual...
Page 2: Safety Notices
Axis Communications AB makes no warranty of any kind with regard to the material contained within this document, including, but not limited to, the implied warranties of merchantability and fitness for a particular purpose.
Page 3 AXIS 5570e/AXIS 5670e User’s Manual dealer. If your questions cannot be answered immediately, your Axis dealer will forward your queries through the appropriate channels to ensure you a rapid response. On www.axis.com, you will find on-line manuals, technical support, software updates, application software and corporate information.
Page 4: About This Manual
About this manual This manual provides introductory information as well as detailed instructions on how to set up and manage the AXIS 5570e/AXIS 5670e in various network environments. It is intended for everyone involved in installing and managing the AXIS 5570e/AXIS 5670e. To fully benefit from the manual, you should be familiar with basic networking principles.
Page 5: Table Of Contents
AXIS 5570e/AXIS 5670e Features and Benefits Section 2 Product Overview 14 Hardware Inventory 14 Protocols and Datastreams 15 The AXIS 5570e Network Print Server 16 The AXIS 5670e Network Print Server 16 Section 3 Basic Installation 19 Getting Started 19...
Page 6 Adding NetBIOS/NetBEUI Printers in Windows 2000 using AXIS Print Monitor 116 Adding Printers over NetBIOS/NetBEUI in Windows NT 4 using AXIS Print Monitor 117 Adding Printers in Windows 98 and Me over TCP/IP using AXIS Print Monitor 119 Adding Printers in Windows 98 and Me over...
Page 7 AXIS 5570e/AXIS 5670e User’s Manual Table of Contents Section 10 Management and Configuration 180 Using a Web browser 181 Using AXIS ThinWizard for Print Server Management 189 Using FTP for Print Server Management 192 Using Telnet 195 Using SNMP 199...
Page 8 Unsupported Fonts 277 Typographical Fonts 278 Section 19 DBCS Support 279 Configuring the AS/400 Host, 5494 CU mode Configuring the AXIS 5570e/AXIS 5670e 280 Verifying the Communications Link 281 Amending Device Features 282 Extended IBM Printer Emulation 283 Font Tables 283...
Page 9: Introduction
Section 1 Introduction Product Model Summary The AXIS 5570e/AXIS 5670e is a LAN attached multi-protocol print server that prints IBM and ASCII data streams to any ASCII printer. Supporting IBM Mainframes, AS/400, NetWare, UNIX, LAN Server Manager, Windows and Apple EtherTalk, these products are ideal for IBM Mainframe and AS/400 sites that are migrating from pure IBM networks to LAN environments.
Page 10: Where To Use It
Section 1: Introduction AXIS 5570e/AXIS 5670e User’s Manual Where to use it Supported The AXIS 5570e/AXIS 5670e is the ideal print server in mixed Environments environments as it can communicate with all the major computer systems and network protocols including: •...
Page 11: How To Use It
Note: The AXIS 5570e/AXIS 5670e is designed for 10 Mbps Ethernet and 100 Mbps Fast Ethernet networks and connects to the network via a twisted pair RJ45 category 5 cable (10baseT and 100baseTX).
Page 12: Axis 5570E/Axis 5670E Features And Benefits
The AXIS 5570e/AXIS 5670e print server provides high performance and reliability combined with low power consumption. The electronic circuits are based on the AXIS ETRAX 100LX chip, which comprises an integrated 32 bit RISC processor and associated network controllers. Flexibility...
Page 13 The AXIS 5570e/AXIS 5670e additionally supports SNMP for remote monitoring. Futureproof You can upgrade the AXIS 5570e/AXIS 5670e Flash memory over FTP, via the print server’s web interface or using AXIS ThinWizard software. This allows you to quickly update and enhance the operational features of your AXIS 5570e/AXIS 5670e when new print server software becomes available.
Page 14: Product Overview
Australia 19111 USA/Japan 19110 AXIS Product CD rev 1.3 or later Printed Material AXIS 5570e/AXIS 5670e User’s Guide 20896 Adhesive Holder & ACC AXIS 5500 CLIPS K 20119 Clip* USB Cable* 70 cm 20208 * Only supplied with AXIS 5570e.
Page 15: Protocols And Datastreams
IPDS SNA (part no. 0194) TCP/IP (part no. 0189) IPDS support SCS support 3270DS support TN3270E TN5250E SNA support Digital Copier Support Note: All models may not be available in all countries in which Axis operates. Please contact your local sales representative for more information.
Page 16: The Axis 5570E Network Print Server
Section 2: Product Overview AXIS 5570e/AXIS 5670e User’s Manual The AXIS 5570e Network Print Server LPT1 Test Button Network Indicator USB1 Ethernet Connector Power Indicator Power Connector The AXIS 5670e Network Print Server Power COM1 Indicator Network Indicator LPT1 LPT2...
Page 17 Section 2: Product Overview Backside label on print server Serial number AXIS 5570e is equipped with one USB port that is USB 1.1 and 2.0 Printer Ports low and full speed compliant, and one high-speed IEEE 1284 compatible parallel port AXIS 5670e is equipped with two high-speed IEEE 1284 compatible parallel ports and one RS232 serial port.
Page 18 See Using a Web browser, on page 181 AXIS Product CD The AXIS Product CD provides an easy-to-use electronic catalog, that includes Axis software, user documentation, etc. All documents presented on the CD are in PDF format.
Page 19: Basic Installation
Basic Installation Getting Started After you have verified that no items in Product Overview, on page 14, are missing from the package, you are ready to install your AXIS 5570e/AXIS 5670e. Follow the instructions below to install the AXIS 5570e/AXIS 5670e in your environment: 1.
Page 20: Connecting A Printer To The Ethernet Network
Follow the instructions below to connect a printer to the network via the AXIS 5570e/AXIS 5670e print server. Important: Make sure that the AXIS 5570e/AXIS 5670e external power supply is marked with the correct voltage! 1. Switch off the printer(s) and disconnect the AXIS 5570e/AXIS 5670e external power supply.
Page 21 AXIS 5570e/AXIS 5670e User’s Manual Section 3: Basic Installation Mounting the AXIS 5570e Using the supplied clip and holder, the AXIS 5570e can be mounted e.g. on the back of the printer or on a wall. Fasten to print server by peeling Adhesive Clip off adhesive tape.
Page 22: Installation Guide
Section 3: Basic Installation AXIS 5570e/AXIS 5670e User’s Manual Installation Guide After connecting the AXIS 5570e/AXIS 5670e to your network, you are now ready to perform the basic setup procedures. The method of installation that you choose should be dictated by your printing requirements and the type of network into which you are integrating.
Page 23 Web browser. FTP, Telnet, SNMP NetBEUI 95/98/NT/Me/2000 AppleTalk Macintosh Web browser, Mac-FTP Web browser, Mac-FTP Recommended installation tools for the AXIS 5570e/AXIS 5670e A shareware LPR spooler is available for Windows for Workgroups. You can download this software from http://www.axis.com/techsup...
Page 24: Setting The Ip Address
IP address to them. JumpStarter JumpStarter, on This software is recommended for small page 27 offices and local networks. Axis software that assists in setting the IP Using AXIS ThinWiz- address of multiple print servers simulta- AXIS ard for Print Server Windows 2000/XP neously.
Page 25 AXIS 5570e/AXIS 5670e User’s Manual Section 3: Basic Installation Dynamic IP address Assignment Obtaining an IP If you have a DHCP server on your network, your print server • address through DHCP will receive an IP address automatically. The IP address will then appear on the test page printed when you press the test button once.
Page 26 Manual IP address To establish communication with the TCP/IP network, an IP Address assignment must be assigned to your AXIS 5570e/AXIS 5670e. Choose the appropriate method according to your network: • AXIS IP JumpStarter™ software is an easy-to-use Windows application that allows you to assign an IP address to your print server and find print servers already installed in your network.
Page 27 3. Click the radio button that corresponds to your choice of IP setting method. 4. Click OK to save your settings. 5. Enter the server root password (by default set to pass), and click 6. The AXIS 5570e/AXIS 5670e will appear in the list with the assigned IP address.
Page 28 5570e/AXIS 5670e in the list and select Server Home Page from the Server menu. Note: If your print server does not appear in the serial number list, refer to the AXIS IP JumpStarter online help files. Setting the IP address...
Page 29 3. If it is not already running, start the RARP daemon. This is typically performed using the command. rarpd -a 4. Restart the AXIS 5570e/AXIS 5670e to download the IP address. Notes: • The Ethernet address is equal to the serial number, which can be found on the underside label of the AXIS 5570e/AXIS 5670e.
Page 30 TFTP server. Just add the name of the config file and the TFTP server’s IP address to your boot table. The config file is downloaded immediately after the AXIS 5570e/AXIS 5670e receives its IP address.
Page 31 AXIS 5570e/AXIS 5670e User’s Manual Section 3: Basic Installation Notes: • The AXIS 5570e/AXIS 5670e supports WINS (Windows Internet Name Service), which is recommended when setting the IP address using DHCP in Windows environments. • The Ethernet Address is the same as the serial number, found on the print server’s underside label.
Page 32 If you are using WINS, you must include at least one WINS server IP address in the DHCP scope. Immediately after the IP address has been received, the AXIS 5570e/AXIS 5670e registers its host name and IP address on the WINS server.
Page 33 AXIS 5570e/AXIS 5670e. Always consult your network administrator before assigning an IP address to your AXIS 5570e/AXIS 5670e. Registering and In order to register the host name of the AXIS 5570e/AXIS 5670e in Resolving networks with dynamic IP address settings, WINS (Windows Internet...
Page 34 Section 3: Basic Installation AXIS 5570e/AXIS 5670e User’s Manual Notes: • The host name limitations conclude that if you want to register the same host name at a WINS server and a DDNS server, the host name should be no longer than 15 characters and it should only contain the characters: ‘A - Z’, ‘a-z’...
Page 35: Setting Up - As/400 (Iseries)
Section 4: Setting Up - AS/400 (iSeries) Section 4 Setting Up - AS/400 (iSeries) This section describes how to configure the AXIS 5570e/AXIS 5670e for printing SCS and IPDS data streams using SNA and TCP/IP transport protocols in the AS/400 (iSeries) environment.
Page 36: Sna Printing - 5494 Mode
Section 4: Setting Up - AS/400 (iSeries) AXIS 5570e/AXIS 5670e User’s Manual If you intend to operate your AXIS 5570e/AXIS 5670e in a multi- protocol environment, you should also proceed to the other relevant sections in this manual: Section 5 Setting Up - IBM Mainframe (zSeries), on page 59...
Page 37 If this is the case, please refer to the Axis Web site for further documentation. Note: You will find an AS/400 Parameter checklist in the AXIS 5570e/AXIS 5670e User’s Guide where you can enter the values described in this section for future reference.
Page 38 Section 4: Setting Up - AS/400 (iSeries) AXIS 5570e/AXIS 5670e User’s Manual 3. Press F11 to display keywords. Display Line Description S44A6643 Line description . . .: LIND ETHLINE Option ..: OPTION *BASIC Category of line .
Page 39 AXIS 5570e/AXIS 5670e User’s Manual Section 4: Setting Up - AS/400 (iSeries) 4. For future reference, note the values of the Local Adapter Address (ADPTADR) and Maximum Controllers (MAXCTL) parameters. Press Enter to view the active switched controllers display. Display Line Description S44A6643 Line description .
Page 40 Section 4: Setting Up - AS/400 (iSeries) AXIS 5570e/AXIS 5670e User’s Manual 5. Press Enter to display the SSAP list. Make sure that there is at least one SSAP entry dedicated for SNA. For your future reference, note the SSAP value for this entry.
Page 41 AXIS 5570e/AXIS 5670e User’s Manual Section 4: Setting Up - AS/400 (iSeries) 6. Press Enter to display the Autocreate controller (AUTOCRTCTL) parameter. Ensure that the AUTOCRTCTL parameter is set to *YES. Press F3 to return to the command line. Display Line Description S44A6643 Line description .
Page 42 Section 4: Setting Up - AS/400 (iSeries) AXIS 5570e/AXIS 5670e User’s Manual 9. Type DSPSYSVAL QAUTORMT on a command line and press Enter. Make sure the Autoconfigure remote controller parameter is turned on(1). Press F3 to exit. Display System Value System value .
Page 43 AXIS 5570e/AXIS 5670e User’s Manual Section 4: Setting Up - AS/400 (iSeries) 11. Type DSPUSRPRF QUSER and press Enter. Make sure that the QUSER Status is *ENABLED. Display User Profile - Basic User profile ....: QUSER Previous sign-on .
Page 44 Device descriptions specific to your AXIS 5570e/AXIS 5670e. Delete the Device Descriptions (indented text) first and then the Controllers. Print a test page if you are unsure of the AXIS 5570e/AXIS 5670e 5494 LU Name. Work with Configuration Status...
Page 45 Configuring the To perform the instructions presented in this section, you should first AXIS 5570e/AXIS assign an IP address to your AXIS 5570e/AXIS 5670e using one of the methods presented in Setting the IP address, on page 24. 5670e After you have completed the procedures in the AS/400 Host system...
Page 46: Configuration Settings
Section 4: Setting Up - AS/400 (iSeries) AXIS 5570e/AXIS 5670e User’s Manual 4. Click the Add Session button. This will start the Configuration Wizard which is a step-by-step guide through the required IBM configuration settings. Notes for SCS printing: •...
Page 47 (xxxxPRT0z is the printer device name) and press Enter. This command starts the writer for this printer device. 3. Press the AXIS 5570e/AXIS 5670e test button once to print a test page. Ensure that the SNA status is defined on the test page as...
Page 48: Tn5250E Printing (Scs Over Ip)
The AS/400 Host System Checklist You will find an AS/400 Parameter checklist in the AXIS 5570e/AXIS 5670e User’s Guide where you can enter the values described in this section for future reference. 1. Type WRKCTLD *VWS on the AS/400 command line and press Enter to determine the number of auto-configured virtual devices on your AS/400 system.
Page 49 1. Start a Web browser, e.g. Internet Explorer or Netscape Navigator. 2. Enter the IP address or the host name of the AXIS 5570e/AXIS 5670e in the location field and press the Enter key on your keyboard. The internal Web pages of the AXIS 5570e/AXIS 5670e will appear.
Page 50 2. Direct a printout to this printer device to check the integrity of the communication link. 3. Press the test button on the AXIS 5570e/AXIS 5670e once to print a test page. Make sure that the TN5250E status is defined...
Page 51: Ppr/Ppd Printing - Ipds Data Streams
PPR/PPD Printing - IPDS data streams Note: IPDS is only available for AXIS 5570e/AXIS 5670e models with the IPDS option installed. For more information, refer to Product Model Summary, on page 9. The configuration procedures presented in this section are divided into three separate steps: •...
Page 52: Underlined Text
Section 4: Setting Up - AS/400 (iSeries) AXIS 5570e/AXIS 5670e User’s Manual 3. Select a name for the PSF configuration and enter it at the line. The name may comprise the configuration (PSFCFG) letters A-Z and the numerals 0-9, but must begin with a letter. A maximum of 10 characters are allowed.
Page 53 AXIS 5570e/AXIS 5670e User’s Manual Section 4: Setting Up - AS/400 (iSeries) Creating a Printer Create a printer device description by following the instructions Device Description below: 1. Issue the command CRTDEVPRT and press Enter. 2. Press F11 to display keywords.
Page 54 Section 4: Setting Up - AS/400 (iSeries) AXIS 5570e/AXIS 5670e User’s Manual Many of the settings presented in the following panel example can be left at their default settings. However, the settings that you must change are highlighted in bold text and the settings that you must enter exactly as shown in the example are highlighted in bold underlined text.
Page 55 AXIS 5570e/AXIS 5670e User’s Manual Section 4: Setting Up - AS/400 (iSeries) Create Device Desc (Printer) (CRTDEVPRT) Type choices, press Enter. Device description ..DEVD > AXISPR1 Device class ..DEVCLS >...
Page 56 Section 4: Setting Up - AS/400 (iSeries) AXIS 5570e/AXIS 5670e User’s Manual User-defined objects ..USRDFNOBJ Object ... . > AXISPR1 Library ..
Page 57 1. Start a Web browser, e.g. Internet Explorer or Netscape Navigator. 2. Enter the IP address or the host name of the AXIS 5570e/AXIS 5670e in the location field and press the Enter key on your keyboard. The internal Web pages of the AXIS 5570e/AXIS 5670e will appear.
Page 58 5. Press F5 to refresh the display. The printer device should now be ACTIVE/WRITER 6. Direct a printout to this printer device. A successful printout verifies the communication link between the AS/400 and the AXIS 5570e/AXIS 5670e. The AXIS 5570e/AXIS 5670e is now ready for printing in the AS/400 environment.
Page 59: Setting Up - Ibm Mainframe (Zseries)
AXIS 5570e/AXIS 5670e User’s ManualSection 5: Setting Up - IBM Mainframe (zSeries) Section 5 Setting Up - IBM Mainframe (zSeries) This section describes how to configure the AXIS 5570e/AXIS 5670e for printing SCS, 3270 and IPDS data streams using SNA and TCP/IP transport protocols in the IBM Mainframe (zSeries) environment.
Page 60: Sna Printing
SNA transport protocol. Important: The AXIS 5570e/AXIS 5670e must be set up to emulate an IBM 3174 (3174 CU mode) in the Mainframe/VTAM environment. Configuring for SNA printing in 3174 CU Mode is described in three separate stages: •...
Page 61 AXIS 5570e/AXIS 5670e. You will instead be working with the gateway VTAM definitions. Since the AXIS 5570e/AXIS 5670e will appear to the host as one or several LU's attached to the gateway PU, you need only add LU definitions to the gateway major node definition and then proceed to item 3 below.
Page 62 Section 5: Setting Up - IBM Mainframe (zSeries) AXIS 5570e/AXIS 5670e User’s Manual 2. Add the Print Server PU and LU definitions to the major node definition. For Switched Major Node definitions you need to: • Add the IDBLK (default = E07) and IDNUM (default = last 5 digits of the AXIS 5570e/AXIS 5670e MAC address) entries to the PU definition.
Page 63 AXIS 5570e/AXIS 5670e User’s ManualSection 5: Setting Up - IBM Mainframe (zSeries) Logon-mode Entry Creating a VTAM Logon-mode entry for your AXIS 5570e/AXIS 5670e. Logon-mode entry for LU type 1 printing) * For application output of LU-1 SNA Character Stream (SCS) TITLE ‘SCS5570e’...
Page 64 Section 5: Setting Up - IBM Mainframe (zSeries) AXIS 5570e/AXIS 5670e User’s Manual Switched major The example below shows how the print server PU, PATH, and LU node definitions definitions may be coded in a switched major node definition. * PU definition * E07xxxxxx is the node ID set in AXIS 5570e/AXIS 5670e.
Page 65 AXIS 5570e/AXIS 5670e User’s ManualSection 5: Setting Up - IBM Mainframe (zSeries) Note: In the PU definition, IDNUM should be set to the five last digits of the AXIS 5570e/AXIS 5670e node address, NODE_ADDR. By default NODE_ADDR stands for the five last digits of the AXIS 5570e/AXIS 5670e serial number.
Page 66 Section 5: Setting Up - IBM Mainframe (zSeries) AXIS 5570e/AXIS 5670e User’s Manual If the LAN media at the remote (Print Server) location differs from that at the host location (e.g. Remote LAN = Ethernet and Host LAN = Token Ring), the MAC...
Page 67 Configuring the To perform the instructions presented in this section, you should first AXIS 5570e/AXIS assign an IP address to your AXIS 5570e/AXIS 5670e using one of the methods presented in Setting the IP address, on page 24. 5670e The purpose of the configuration of the AXIS 5570e/AXIS 5670e is to emulate a LAN attached IBM 3174 Control Unit running SNA PU2.0.
Page 68 Section 5: Setting Up - IBM Mainframe (zSeries) AXIS 5570e/AXIS 5670e User’s Manual 4. Click the Add Session button. This will start the Configuration Wizard which is a step-by-step guide through the required configuration settings. Notes for SCS printing: •...
Page 69 • LU-3 Note: Please refer to the Parameter List and FAQ on the Axis Web site, if the status line indicates that the SNA link is not active. The AXIS 5570e/AXIS 5670e is now ready for use in the SNA...
Page 70: Tcp/Ip Tn3270E Printing
Section 5: Setting Up - IBM Mainframe (zSeries) AXIS 5570e/AXIS 5670e User’s Manual TCP/IP TN3270E Printing The following procedures describe how to configure the AXIS 5570e/AXIS 5670e for SCS, 3270DS and IPDS printing, using TCP/IP TN3270E. This is achieved by establishing communication between the AXIS...
Page 71 1. Start a Web browser, e.g. Internet Explorer or Netscape Navigator. 2. Enter the IP address or the host name of the AXIS 5570e/AXIS 5670e in the location field and press the Enter key on your keyboard. The internal Web pages of the AXIS 5570e/AXIS 5670e will appear.
Page 72 Section 5: Setting Up - IBM Mainframe (zSeries) AXIS 5570e/AXIS 5670e User’s Manual Notes for SCS printing: • In the Configuration Wizard, Non-IPDS Printer Emulation uses value structure 38xx for LaserWriter printers. All other values can be used for matrix printers.
Page 73 AXIS 5570e/AXIS 5670e User’s ManualSection 5: Setting Up - IBM Mainframe (zSeries) Microsoft SNA Server Communication is established in two separate stages, SNA Server-to- Host connection and SNA Server to AXIS 5570e/AXIS 5670e connection, as described below: SNA Server-to-Host Connection...
Page 74 Section 5: Setting Up - IBM Mainframe (zSeries) AXIS 5570e/AXIS 5670e User’s Manual 6. Click OK. SNA Server Manager Main Window SNA Server - AXIS 5570e/AXIS 5670e connection 1. Select the new LUA and drag it to the TN3270 connection definition (highlighted in the SNA Server Manager Window above).
Page 75 AXIS 5570e/AXIS 5670e User’s ManualSection 5: Setting Up - IBM Mainframe (zSeries) Verifying the 1. Activate the connection you created in step 2 of the above SNA Communication: Server - AXIS 5570e/AXIS 5670e connection procedures. The status of the connection should be “active”.
Page 76 Section 5: Setting Up - IBM Mainframe (zSeries) AXIS 5570e/AXIS 5670e User’s Manual 4. Leave the rest at their default settings. Peer PU profile 5. Click the TN3270 icon. The panel below will appear. 6. Select All Available Host PU profiles.
Page 77 AXIS 5570e/AXIS 5670e User’s ManualSection 5: Setting Up - IBM Mainframe (zSeries) PU profile name and Logical adapter 10. Press the “insert” key to create a new Host PU Profile. Choose Host PU Profile from the list displayed in the dialog. Then the panel below will appear.
Page 78 Section 5: Setting Up - IBM Mainframe (zSeries) AXIS 5570e/AXIS 5670e User’s Manual 21. Set Default LU type to Printer (LU type 1 or 3). 22. Specify the VTAM LU name prefix. Click OK. Notes: • When the LUs are created the default names for the Printer Devices will be <name prefix>...
Page 79 AXIS 5570e/AXIS 5670e User’s ManualSection 5: Setting Up - IBM Mainframe (zSeries) Profile Name NWSAA Number of local service access points: Enable adapter at startup: PU Profile Name NWSAAPU Number of dependent LUs: Starting dependent LU number: Peripheral node control point name:...
Page 80 Section 5: Setting Up - IBM Mainframe (zSeries) AXIS 5570e/AXIS 5670e User’s Manual Profile Name NWSAA Enable PU profile at startup: Termination LU id Category VTAM LU Name Type Method Public TSELF Public BRLTST04 TSELF Public BRLTST05 TSELF Public BRLTST06...
Page 81 AXIS 5570e/AXIS 5670e User’s ManualSection 5: Setting Up - IBM Mainframe (zSeries) 2. Send a print job from the host. The AXIS 5570e/AXIS 5670e is now ready for use. If needed, it can be further adapted to your system using the Web-based configuration pages or IBM Printer Emulation.
Page 82: Ppr/Ppd Printing - Ipds Data Streams
Section 5: Setting Up - IBM Mainframe (zSeries) AXIS 5570e/AXIS 5670e User’s Manual PPR/PPD Printing - IPDS data streams Important: IPDS is only available for print server models with the IPDS option installed. Please refer to Product Model Summary, on page 9.
Page 83 AXIS 5570e/AXIS 5670e User’s ManualSection 5: Setting Up - IBM Mainframe (zSeries) Specifying the TCP/IP To specify a TCP/IP address space name you should enter the address space name following EXEC statement in the appropriate PSF writer procedure: //STEP01 EXEC...
Page 84 Section 5: Setting Up - IBM Mainframe (zSeries) AXIS 5570e/AXIS 5670e User’s Manual Modifying the The TCP/IP profile contains system configuration statements used to TCP/IP profile initialize the TCP/IP address space. Among those statements, the following are subject to special considerations when you are printing from PSF on TCP/IP-attached printers: •...
Page 85 PSF relies on TCP to detect when a connection with a TCP/IP-attached printer or an AXIS 5570e/AXIS 5670e is no longer available. When no data has been exchanged between PSF and its connection partner, TCP sends keep-alive probes to the connection partner periodically. These...
Page 86 Section 5: Setting Up - IBM Mainframe (zSeries) AXIS 5570e/AXIS 5670e User’s Manual Configuring the Follow the instructions below to configure your AXIS 5570e/AXIS AXIS 5570e/AXIS 5670e using a standard Web browser: 5670e 1. Start a Web browser, e.g. Internet Explorer or Netscape Navigator.
Page 87 (Use ATTN to interrupt.) EZA0464I PING: Ping #1 timed out If the ping is not successful make sure the AXIS 5570e/AXIS 5670e is configured according to the instructions in Setting the IP address, on page 24 and in Configuring the AXIS 5570e/AXIS 5670e, on page 71.
Page 88 Section 5: Setting Up - IBM Mainframe (zSeries) AXIS 5570e/AXIS 5670e User’s Manual JES definitions When a TCP-attached printer is to be used with JES, it must be defined for deferred-printing mode. To use a PSF printer for deferred printing under JES, you must first code JES initialization statements to define FSSs and FSAs for PSF printers.
Page 89 AXIS 5570e/AXIS 5670e User’s ManualSection 5: Setting Up - IBM Mainframe (zSeries) The following paragraphs describe the JES2 initialization statements shown above, which are typical of the JES2 statements used with PSF. For more detailed descriptions of all JES2 initialization statements, refer to the JES2 initialization and tuning publication for your operating system.
Page 90 Specifies the FSS for this device and must match the FSA name specified in the corresponding FSS statement. This parameter is required. Enables form markings to be placed on the job trailer pages. For the AXIS 5570e/AXIS 5670e you should set this parameter to NO.
Page 91 Explanation Specifies the data-set processing modes supported for the printer. It lists all the PRMODE values that the printer accepts. If the AXIS 5570e/AXIS 5670e is connected to a PostScript printer, the correct setting is PRMODE .. This setting indicates that composed-page and line data sets can be PRMODE=(PAGE,LINE,) printed.
Page 92 Section 5: Setting Up - IBM Mainframe (zSeries) AXIS 5570e/AXIS 5670e User’s Manual The following paragraphs describe the JES3 initialization statements shown above, which are typical of the JES3 statements used with PSF. For more detailed descriptions of all JES3 initialization statements, refer to the JES3 initialization and tuning publication for your operating system.
Page 93 In this case, printer performance is significantly reduced if PSF errors continue to occur. The recommended starting value is 100. Identifies the printer device type. For the AXIS 5570e/AXIS 5670e you should specify the parameter value DTYPE .
Page 94 MODE Specifies that the printer is managed by an FSS. This parameter is required. Specifies which data-set processing mode is supported. For the AXIS 5570e/AXIS 5670e attached to Postscript printers, the correct setting is , indicating that composed-page and line PRMODE=(LINE,PAGE,) data sets can be printed.
Page 95 IPADDR PORTNO PRINTDEV TCP/IP port number 5100 is used, but any port, larger that 1024, can be used as long as the same port is set up in the AXIS 5570e/AXIS 5670e. procedure contains JCL parameters to produce a APSWPROT startup procedure for either 240-pel and 300-pel printers, but the references to 300-pel resolution are commented out.
Page 96 Section 5: Setting Up - IBM Mainframe (zSeries) AXIS 5570e/AXIS 5670e User’s Manual If you want to print both 240-pel and 300-pel AFP/IPDS jobs, create two separate FSAs, one for jobs with resolution of 120 or 240, and one for jobs with resolution of 300 pels. The 240-pel resolution FSA uses 240-pel resources, and the 300-pel resolution FSA uses 300-pel resources.
Page 97 AXIS 5570e/AXIS 5670e User’s ManualSection 5: Setting Up - IBM Mainframe (zSeries) Example continues CONT... //* REQUIRED ACTIONS = RESOLUTION - THIS START PROCEDURE IS SET UP FOR DRIVING A TCP/IP DEVICE AT 240 PEL RESOLUTION. TO CHANGE IT TO DRIVE 300 PEL RESOLUTION TCP/IP ATTACHED DEVICES:...
Page 98 Section 5: Setting Up - IBM Mainframe (zSeries) AXIS 5570e/AXIS 5670e User’s Manual Example continues CONT... //* ************************************************************ PRINTDEV //* ************************************************************ //PRT1 CNTL //PRT1 PRINTDEV FONTDD=*.FONT01, /* 240 PEL FONT LIBRARY DD /* <-- SEE REQUIRED ACTIONS /* ABOVE //*PRT1 PRINTDEV FONRDD=*.FONT02, /* 300 PEL FONT LIBRARY DD...
Page 99 AXIS 5570e/AXIS 5670e User’s ManualSection 5: Setting Up - IBM Mainframe (zSeries) Although it is not recommended, it is possible to drive the printer with just one FSA, if one of the following conditions are met: • All the resources in the resource libraries are resolution-indepen- dent, and all the jobs that use inline resources or user libraries contain resources that are resolution-independent.
Page 100 Section 5: Setting Up - IBM Mainframe (zSeries) AXIS 5570e/AXIS 5670e User’s Manual When you install PSF, you must create or update the required libraries referenced by the startup procedure, and you should consider any need to increase the region size, as specified in the EXEC statement, to accommodate resources and an increased number of printer FSAs.
Page 101: Setting Up - Windows
Having connected the AXIS 5570e/AXIS 5670e to your network, as described in Connecting a printer to the Ethernet Network, on page 20, this section describes how to install the AXIS 5570e/AXIS 5670e in the Windows environment. Identify your Windows platform and follow the installing instructions from the list below.Overview of...
Page 102: Adding Printers In Windows 2000/ Windows Xp Over Tcp/Ip (Lpr)
Section 6: Setting Up - Windows AXIS 5570e/AXIS 5670e User’s Manual If you intend to use the AXIS 5570e/AXIS 5670e in a multiprotocol environment, you should also refer to the following sections: Section 7 Setting Up - NetWare, on page 123...
Page 103 AXIS 5570e/AXIS 5670e User’s Manual Section 6: Setting Up - Windows 2. Select Local Printer attached to this computer. Make sure the Automatically detect and install my Plug and Play printer check box is not checked. Click Next. 3. Click the Create a new port radio button and select Standard TCP/IP Port from the list.
Page 104 Section 6: Setting Up - Windows AXIS 5570e/AXIS 5670e User’s Manual 4. Enter the IP address of the print server (Example: 192.168.3.191) The Port Name field will be filled in automatically when you enter the IP address. Add the port you want to use as a suffix (optional):...
Page 105 AXIS 5570e/AXIS 5670e User’s Manual Section 6: Setting Up - Windows 5. In the Additional Port Information Required window, enter the Device Port you want to use, you will see LPT1, LPT2 and COM1 in a drop-down menu: 5570e: Physical print server port connected to printer...
Page 106 Section 6: Setting Up - Windows AXIS 5570e/AXIS 5670e User’s Manual Click Next and Finish 6. Select Manufacturer and Printer from the driver list. Click Next.
Page 107 AXIS 5570e/AXIS 5670e User’s Manual Section 6: Setting Up - Windows 7. Choose whether you want to keep the existing driver or to replace it. If you already have the printer’s driver installed, you will be asked whether to keep it or to replace it.
Page 108 Select the appropriate radio button and click Next and Finish. 10. Print a test page to verify your installation. You have now completed the installation. ¨ Check www.axis.com/techsup for updates on the ‘tcpmon.ini’ file!
Page 109: Adding Printers In Windows 2000/Windows Xp Using The Microsoft Lpr Monitor
AXIS 5570e/AXIS 5670e User’s Manual Section 6: Setting Up - Windows Adding Printers in Windows 2000/Windows XP using the Microsoft LPR Monitor This section describes how to set up a Windows 2000/XP server for LPR printing over the TCP/IP protocol, using the built-in Microsoft LPR Monitor i.e.
Page 110 Section 6: Setting Up - Windows AXIS 5570e/AXIS 5670e User’s Manual 1. Go to Start | Printers and Faxes and click the Add a Printer icon Windows XP: to start the Add Printer Wizard. Click Next. 1. Go to Start | Settings | Printers and click the Add Printer icon Windows 2000: to start the Add Printer Wizard.
Page 111 AXIS 5570e/AXIS 5670e User’s Manual Section 6: Setting Up - Windows If you wish to print over LPR but do not wish to install Print Services Alternative Method for for Unix you can do this by changing the printing protocol after...
Page 112: Adding Printers In Windows Nt 4 Using The Microsoft Lpr Monitor
Section 6: Setting Up - Windows AXIS 5570e/AXIS 5670e User’s Manual Adding Printers in Windows NT 4 Using the Microsoft LPR Monitor If you have not already done so, you should perform the TCP/IP basic setup procedures prior to installing a printer for LPR printing.
Page 113 AXIS 5570e/AXIS 5670e User’s Manual Section 6: Setting Up - Windows 5. Type the print server’s name or IP address in the field Name or address of server providing lpr (Example: 10.13.6.198). Then enter which port to use in the field Name of printer or print queue on that server according to the table below (Example: USB1).
Page 114: Axis Print Monitor Software
Note: AXIS Print Monitor can also be used for DOS printing. Please refer to the AXIS Print Monitor’s Readme file for instructions. The Readme file is located in the same folder where AXIS Print Monitor is installed on your PC.
Page 115: Adding Printers Over Tcp/Ip In Windows Nt
3. The Wizard asks you to select My Computer or Network printer server. Select My Computer, click Next. 4. Click Add Port... In the Available Ports dialog, select AXIS Port and click New Port... 5. Select LPR (TCP/IP) as your choice of protocol and click OK.
Page 116: Adding Netbios/Netbeui Printers In Windows 2000 Using Axis Print Monitor
4. Select NetBIOS/NetBEUI as your choice of network protocol and click OK. 5. Select the AXIS Port you want to add from the list of available ports. The port appears as <name>.<port> (Example: AX100086.LP1). The <port> is taken from the table below. Click OK.
Page 117: Adding Printers Over Netbios/Netbeui In Windows Nt 4 Using Axis Print Monitor
3. The Wizard asks you to select My Computer or Network printer server. Select My Computer. Click Next. 4. Click Add Port... In the Available Ports dialog, select AXIS Port and click New Port... 5. Select NetBIOS/NetBEUI as your choice of network protocol and...
Page 118 Section 6: Setting Up - Windows AXIS 5570e/AXIS 5670e User’s Manual 6. Select the AXIS Port you want to add from the list of available ports. The port appears as <name>.<port> (Example: AX100086.LP1). The <port> is taken from the table below. Click OK.
Page 119: Adding Printers In Windows 98 And Me Over Tcp/Ip Using Axis Print Monitor
AXIS 5570e/AXIS 5670e User’s Manual Section 6: Setting Up - Windows Adding Printers in Windows 98 and Me over TCP/IP using AXIS Print Monitor 1. Install AXIS PrintMonitor on all workstations that will print via the Axis print server. 2. Next, start the Windows Add Printer Wizard: select Settings | Printers from the Start menu and double-click the Add Printer icon.
Page 120 Section 6: Setting Up - Windows AXIS 5570e/AXIS 5670e User’s Manual 12. Click the radio button “other”. Select AXIS Port and then click 13. Select LPR (TCP/IP) as your choice of protocol and click OK. 14. Enter the IP address or the host name of your print server (Example IP address: 192.168.3.191 or host name: AXIS181636).
Page 121: Adding Printers In Windows 98 And Me Over Netbios/Netbeui Using Axis Print Monitor
AXIS 5570e/AXIS 5670e User’s Manual Section 6: Setting Up - Windows Adding Printers in Windows 98 and Me over NetBIOS/NetBEUI using AXIS Print Monitor Follow the procedures below to install Axis NetBIOS/NetBEUI printer ports on a Windows 98 workstation, using AXIS Print Monitor: 1.
Page 122 Section 6: Setting Up - Windows AXIS 5570e/AXIS 5670e User’s Manual 6. Select the AXIS Printer Port from the Available Ports list. The port names appears as <name>.<port>. Here, <name> is AX followed by the last six digits of the print server’s serial number (e.g.
Page 123: Setting Up - Netware
NetPilot” on page 150.. See “NetWare Administration” on page 156. for information on Novell’s administration tools. If you intend to operate your AXIS 5570e/AXIS 5670e in a multi- protocol, mixed environment, you should also proceed to the other relevant sections in this manual.
Page 124: Setup Using Ndps
Follow the instructions below to install the AXIS 5570e/AXIS 5670e using NDPS: Important: The NDPS Enabled parameter of the AXIS 5570e/AXIS 5670e must be set to • Yes in order for the communication between the print server and the NDPS gateway to be enabled.
Page 125 Agent List button. The Printer Agent List dialog will appear. 3. Click New. The Create Printer Agent dialog will appear. 4. Type a name of your choice in the NDPS Printer Agent field: 5. Select the Axis Gateway configuration in the Gateway Type window. 6. Click OK...
Page 126 Section 7: Setting Up - NetWare AXIS 5570e/AXIS 5670e User’s Manual 7. In the Select the printer’s type window, choose your printer. If you cannot find the printer, select an appropriate Generic one (PCL, PS, etc) 8. Select TCP/IP (default) or IPX as network protocol. Click Next.
Page 127 AXIS 5570e/AXIS 5670e User’s Manual Section 7: Setting Up - NetWare 1. Only the ports with a connected printer show up in this window. If the printer is not in the displayed print list, click Manually specify the print server and do the following: Enter the Print Servers’...
Page 128 Section 7: Setting Up - NetWare AXIS 5570e/AXIS 5670e User’s Manual The IPX Addresses for the above printers will appear as: <IPX External Network Number>:<Print Server’s HW address>:<Socket Number> i.e.: 01d7e1c2:00408c5ff6a6:400c where 400c, 401c, and 402c are the socket numbers correspond-...
Page 129 AXIS 5570e/AXIS 5670e User’s Manual Section 7: Setting Up - NetWare 3. Choose a port in the Print Server Port field, e.g. 01d7e1c2:00408c5ff6a6 and LPT1 The port numbers are USB1*, LPT1, LPT2 or COM1. Ports available *USB1 port Parallel port 1 Parallel port 2 Serial port...
Page 130 Section 7: Setting Up - NetWare AXIS 5570e/AXIS 5670e User’s Manual 6. Click Continue and OK in the next NDPS window. The new Printer Agent appears in the Printer Agent List window. Check the Status: it should be Idle. 7. Press Cancel to close the NDPS Manager To install the printer on the workstation, See “Installing an NDPS...
Page 131 AXIS 5570e/AXIS 5670e User’s Manual Section 7: Setting Up - NetWare 4. From the Object menu, select Create. The New Object dialog appears. 5. Select NDPS Printer. The Create NDPS Printer dialog appears.
Page 132 NDPS Manager to which you want to assign it 9. Select AXIS Gateway Configuration in the Gateway Type field. 10. Click OK. 11. In the Select the printer’s type window choose your printer. If you...
Page 133 AXIS 5570e/AXIS 5670e User’s Manual Section 7: Setting Up - NetWare 12. Select TCP/IP (default) or IPX as network protocol. 13. Click Next. 14. You will find the print server in the next window with the printer attached on the connected port.
Page 134 Section 7: Setting Up - NetWare AXIS 5570e/AXIS 5670e User’s Manual If the printer is not in the displayed print list: 1. Click Manually specify the print server enter the Print Servers’ IP address in the IP Address Field. 2. Choose a port in the Print Server Port field e.g., 192.168.70.243 and LPT1: The port numbers are USB1*, LPT1, LPT2 or COM1.
Page 135 AXIS 5570e/AXIS 5670e User’s Manual Section 7: Setting Up - NetWare The IPX Addresses for the above printers will appear as: <IPX External Network Number>:<Print Server’s HW address>:<Socket Number> i.e.: 01d7e1c2:00408c5ff6a6:400c where 400c, 401c, and 402c are the socket numbers correspond-...
Page 136 Section 7: Setting Up - NetWare AXIS 5570e/AXIS 5670e User’s Manual 3. Choose a port in the Print Server Port field: e.g.: 01d7e1c2:00408c5ff6a6 and LPT1. The port numbers are USB1*, LPT1, LPT2 or COM1. Ports available *USB1 port Parallel port 1...
Page 137 AXIS 5570e/AXIS 5670e User’s Manual Section 7: Setting Up - NetWare 5. Next, select the printer drivers for each client operating system. (Windows 2000, Windows NT4 and Windows 95/98). These drivers will be automatically downloaded to users’ workstations when they install this printer in the future.
Page 138 Section 7: Setting Up - NetWare AXIS 5570e/AXIS 5670e User’s Manual 1. Log in as Admin. Using Novell Printer Manager 2. On the any workstation, browse to <NW 5.1 File Server>\SYS:PUBLIC\Win32 and start Nwpmw32.exe (Novell Printer Manager). The Novell Printers dialog appears, displaying a list of installed Public or Controlled printers (if any printers have previously been installed on the workstation).
Page 139 AXIS 5570e/AXIS 5670e User’s Manual Section 7: Setting Up - NetWare 5. The list of available printers shows the NDPS Public Access Printers on the network and the NDPS Controlled Access Printers in you current NDS context. To see the Controlled Access Printers in other context that you have rights to, click the Browse button and select your choice.
Page 140 Section 7: Setting Up - NetWare AXIS 5570e/AXIS 5670e User’s Manual 7. Click OK. The default driver for that printer is then automatically downloaded. If the printer object does not have a printer driver associated with it, or a driver was not found, you will be prompted to either to choose from a list of printer drivers provided by NDPS or to provide a disk with the appropriate driver.
Page 141 AXIS 5570e/AXIS 5670e User’s Manual Section 7: Setting Up - NetWare 9. Verify by clicking Start - Settings - Printers on the workstation. 1. Click Start on your workstation, select Settings =>Printers. Using the Add Printer Wizard There might be some differences regarding this menu depending of MS Operating System you are running.
Page 142 Section 7: Setting Up - NetWare AXIS 5570e/AXIS 5670e User’s Manual 3. Select Network printer and click Next. 4. Click Next again in the Locate Your Printer dialog (Win2000/XP) or press the Browse button (Win9X) 5. Browse to the NDPS Printers. Expand either the NDPS Controlled Access Printers or the NDPS Public Access Printers folder, select your newly installed NDPS printer and follow the instructions.
Page 143: Setup Using Iprint
Axis Gateway Configuration Utility for use with earlier versions of NetWare from www.axis.com. • To print using TCP/IP, Axis print server firmware 6.1 or later is required. In order to print using IPX/SPX, Axis print server firmware 5.51 or later is needed.
Page 144 AXIS LPR Gateway Configuration will automatically be installed and configured on the NetWare Servers and ready for use. The AXIS IPP Gateway Configuration Snap-in for NetWare 6.0 can be downloaded for free from www.axis.com. Follow the instructions below to install the AXIS IPP Gateway Configuration Snap-in for NetWare 6.0, if you want to add it in your iPrint environment.
Page 145 8. Click on iPrint Management on the left pane and select Create Printer. 9. On the right pane, verify that the newly installed AXIS IPP Gateway Configuration is under the Gateway type drop-down menu. If not, it may be necessary to restart the NetWare server.
Page 146 11. Choose the context where the printer will be installed. 12. Browse for the NDPS Manager and select it. 13. In the Gateway Type drop-down list, choose the Axis IPP Gateway Configuration. Press Next. 14. In the Printer URL, you may choose either the IPP version 1.0 format: http://<IP address of your print server>:631/lptx...
Page 147 11. Choose the context where the printer will be installed. 12. Browse for the NDPS Manager and select it. 13. In the Gateway Type drop-down list, choose the Axis LPR Gateway Configuration. Click Next. 14. Choose either the IP address or the DNS Name for your print server.
Page 148 Section 7: Setting Up - NetWare AXIS 5570e/AXIS 5670e User’s Manual ® Installing the iPrint In order for users to use iPrint, they need to install the Novell iPrint Printer using the Client software and a printer. When a user selects a printer to be iPrint Client.
Page 149: Basic Setup With Axis Netpilot
1. Start AXIS NetPilot by double-clicking the NetPilot icon, which is located in the folder where you installed AXIS NetPilot. 2. Locate the AXIS 5570e/AXIS 5670e in the ‘New Axis Units’ folder. Select it and click the Install button on the AXIS NetPilot toolbar.
Page 150: Advanced Installation Using Axis Netpilot
Assigning an IP Address to the Print Server, on page 14 for further information about setting the IP address. The AXIS 5570e/AXIS 5670e uses the print server name followed by Print Queues the printer port as the default Print Queue name and print server port name.
Page 151 NetWare Network The NetWare Network Environment window allows you to connect Environment Window additional print queues to your AXIS 5570e/AXIS 5670e as well as create new ones. Follow the steps below to gain access to the NetWare Network Environment window: 1.
Page 152 8. Select Print Server Mode or Remote Printer Mode. If you selected Print Server Mode, advance directly to step 11, otherwise continue with step 9. 9. Select an appropriate NetWare Print Server name, that will be associated with the AXIS 5570e/AXIS 5670e print server, by using the Browse... button.
Page 153: Basic Queue-Based Printing Over Ip
11. Click the OK button to return to the Network Environments window. Basic Queue-based printing over IP Axis print servers with software version 6.0 or later allow users to print in a Pure IP environment using traditional queue-based printing (which usually uses the IPX transport protocol). Note that only NDS queue-based printing is supported.
Page 154 (example: AXISXXXXXX.<context>, where <context> is the container where you want to create your print server) Setting the PSERVER parameters in the AXIS 5570e/AXIS 5670e Web interface. 4. Use the NetWare Administrator to create the printer, print server and queue objects in the NDS tree and then link them together. The Print Services Quick Setup (Non-NDPS) utility can be used for this.
Page 155 The following overview explains the advantages and limitations of Methods the two supported queue-based printing methods. The AXIS 5570e/AXIS 5670e logs in to a file server(s) and repeatedly Print Server Mode polls the print queues for print jobs. In this fashion, the AXIS 5570e/AXIS 5670e emulates a NetWare print server, which is a workstation running PSERVER.
Page 156 Printer Status The Printer Status menu, detailed below, shows the status of an active print job serviced by an AXIS 5570e/AXIS 5670e network print server. It displays detailed information concerning the active job including, Print Queue, print job description, size of print file, percentage of job completed, etc.
Page 157 AXIS 5570e/AXIS 5670e User’s Manual Section 7: Setting Up - NetWare Print Layout You can view installed AXIS 5570e/AXIS 5670e and their relative print queues for any NetWare Organizational Unit. You can also dis- play summary information by right-clicking on the printer object you...
Page 158: Setting Up - Macintosh
AXIS 5570e/AXIS 5670e User’s Manual Section 8 Setting Up - Macintosh Having connected the AXIS 5570e/AXIS 5670e to your network, this section now describes how to set up your print server for printing in Mac OS X and earlier Macintosh environments using AppleTalk.
Page 159: Installation On Macos 9.1 Or Older, Using Appletalk
AXIS 5570e/AXIS 5670e User’s Manual Section 8: Setting Up - Macintosh Note: If you want to print using LPR, select: 1. Printers | Add Printer... 2. From the Printer List dialog, select LPR printers using IP. 3. Enter the IP address or host name of the print server in the LPR printer’s Address field.
Page 160: Choosing A Printer
Section 8: Setting Up - Macintosh AXIS 5570e/AXIS 5670e User’s Manual Choosing a Printer Selecting a Printer The method for choosing a printer varies depending on which version of LaserWriter printer driver you are using. • The LaserWriter 7.0 driver assumes that you use a standard PostScript driver, and cannot take advantage of any printer specific features.
Page 161 Repeat this procedure for each Macintosh computer on the network using the print server. Bi-directional The AXIS 5570e/AXIS 5670e allow the printer driver to communicate Support directly with the printer and consequently facilitates complete functional control over print jobs, e.g. automatic downloading of...
Page 162 You simply need to print a document from the Macintosh computer to verify communication to the chosen printer. The basic installation can be considered complete if the print test is satisfactory. The AXIS 5570e/AXIS 5670e is now ready for use.
Page 163 AXIS 5570e/AXIS 5670e User’s Manual Section 8: Setting Up - Macintosh Setting Parameters In AppleTalk, you can change a limited number of the parameters of the AXIS 5570e/AXIS 5670e. You can: • enable and disable binary data transfers for your printing •...
Page 164 8. Open the Chooser and select the printer port you wish to use for printing documents. 9. Close the Chooser. Note: The _CFG port disappears 60 minutes after the AXIS 5570e/AXIS 5670e has been powered on. If you want it to reappear, you must restart your print server.
Page 165: Setting Up - Unix
AXIS 5570e/AXIS 5670e User’s Manual Section 9: Setting Up - UNIX Section 9 Setting Up - UNIX Print Tools For printer configuration, printtool and printconfig are the most common. How they are invoked depends on which distribution and window manager you use.
Page 166 Section 9: Setting Up - UNIX AXIS 5570e/AXIS 5670e User’s Manual Red Hat printconf is the recommended printing tool. The program contains an integrated printer driver list, but does not have printer detection functionality. Instructions: Type the command printconf-gui in a Terminal window to start the graphical version.
Page 167: Typical Invocation Via A Windows Manager
AXIS 5570e/AXIS 5670e User’s Manual Section 9: Setting Up - UNIX Notes: • A versatile IPP client for UNIX/Linux is CUPS. It can be downloaded from the Common Unix Printing System’s Web site at www.cups.org • If you don't find your specific printer in your distribution, have a look at http://www.linuxprinting.org/database.html...
Page 168: Debian 3.0
Section 9: Setting Up - UNIX AXIS 5570e/AXIS 5670e User’s Manual version. The same information as was described above will be needed. Note: In Mandrake, even if you type at a shell prompt, printtool will automatically start. printerdrake Debian 3.0 Debian offers a choice between plain LPD, LPRng and CUPS.
Page 169: Red Hat 7.3
AXIS 5570e/AXIS 5670e User’s Manual Section 9: Setting Up - UNIX Text fields for the following options appears: Printer name — Enter a unique name for the printer. (The name cannot contain spaces and must begin with a letter. Valid characters are a - z, A - Z, 0 - 9, -, and _.
Page 170: Local Printer
Section 9: Setting Up - UNIX AXIS 5570e/AXIS 5670e User’s Manual 4. You can also run as a text based application if you do printconf not have the X Window System installed, or you just prefer the text based interface. To run it, log in as root (or use the command to temporarily change to the root user), and type the command from a shell prompt.
Page 171 AXIS 5570e/AXIS 5670e User’s Manual Section 9: Setting Up - UNIX Adding a Remote To add a remote UNIX printer, such as one attached to a different Unix Printer UNIX/Linux system on the same network, click the New button in the main window.
Page 172: Suse 8.0
Section 9: Setting Up - UNIX AXIS 5570e/AXIS 5670e User’s Manual SuSE 8.0 The printing system on SuSE Linux is based on an apsfilter, with some enhancements; SuSE's apsfilter will recognize all common file formats (including HTML, if html2ps is installed).
Page 173: Axis Axinstall Script
PROS, LPR, FTP or Reverse Telnet protocols. However, if you want to integrate the AXIS 5570e/AXIS 5670e with your host spooler, you can use the Axis automatic installation script axinstall.
Page 174 Section 9: Setting Up - UNIX AXIS 5570e/AXIS 5670e User’s Manual FTP version. > ftp npserver connected to npserver. 220 AXIS 5570e/AXIS 5670e FTP Print Server v6.42 March 23 2003 ready. Name (npsserver:thomas): root 331 User name ok, need password (not visible)
Page 175 AXIS 5570e/AXIS 5670e User’s Manual Section 9: Setting Up - UNIX Note: NLPRng is not supported by axinstall. The axinstall script will suggest one of the systems listed below when started. If you do not find the suggestion appropriate, then manually select any of the systems listed.
Page 176: Print Methods On Tcp/Ip Networks
Section 9: Setting Up - UNIX AXIS 5570e/AXIS 5670e User’s Manual Print Methods on TCP/IP Networks The AXIS 5570e/AXIS 5670e supports several different print methods in the TCP/IP environment. axinstall will suggest a print method suitable for your particular UNIX/Linux system, but you might want to use another method depending on your printing requirements (banner pages, status logging, etc).
Page 177 This is the recommended method for UNIX/Linux systems, but some System V versions do not support LPD. Advantages: Easy to set up — install the AXIS 5570e/AXIS 5670e as a remote queue in System V, or add a remote printer to /etc/printcap using the fields (BSD).
Page 178 A protocol developed at Axis. Comes in two versions; named pipe (PROS A) and filter (PROS B). The AXIS 5570e/AXIS 5670e appears as a device to the system. This PROS A makes all filter and model options available. It provides accounting Advantages and status logging.
Page 179 IBM MVS Systems A sample JCL script, , is available in the directory of the jclex print server. It gives an example of how to print a file from an MVS mainframe to an AXIS 5570e/AXIS 5670e using FTP.
Page 180: Management And Configuration
• Reset the AXIS 5570e/AXIS 5670e Configuration The method you should use to manage and configure your AXIS Overview 5570e/AXIS 5670e depends on the operating system protocols of your network. The table below displays which method to use for each supported environment.
Page 181: Using A Web Browser
Once you have established the AXIS 5570e/AXIS 5670e in the TCP/IP environment, as described in Setting the IP address, on page 24, you are free to access the AXIS 5570e/AXIS 5670e Web pages from any standard Web browser. The Web interface of the AXIS 5570e/AXIS 5670e is divided into two modes of operation, User mode and Admin mode.
Page 182 Section 10: Management and Configuration AXIS 5570e/AXIS 5670e User’s Manual Accessing the Web Follow the steps below to access the internal web pages of the AXIS Pages 5570e/AXIS 5670e: 1. Enter the print server’s IP address (or host name) in the Location/Address field of your Web browser.
Page 183 Help The Help page presents you with basic information about the AXIS 5570e/AXIS 5670e and the Web user interface. A short description of the Axis installation tools you should use when installing a printer on your PC, is also included.
Page 184 This Print Server The This Print Server page contains a section that allows you to view and modify the general parameter setting of the AXIS 5570e/AXIS 5670e, including the print server name, the node address, the password and the base URL. You can also configure any of the eight logical printers of the AXIS 5570e/AXIS 5670e.
Page 185 AXIS 5570e/AXIS 5670e User’s Manual Section 10: Management and Configuration Print Jobs From the Print Jobs page you can view the status of the current print jobs, including the number of printed bytes and the origin of the print job. You can also view a log of the 20 latest print jobs that includes the user, the printing protocol and the file size.
Page 186 Network Settings From the Network Settings page you can set all parameters that control the network traffic to and from the AXIS 5570e/AXIS 5670e. You can enable or disable any of the supported network protocols and fine-tune the parameter settings.
Page 187 Section 10: Management and Configuration Statistics The Statistics page displays information about the network traffic to and from the AXIS 5570e/AXIS 5670e as well as information about servers and services that are connected or associated with the AXIS 5570e/AXIS 5670e.
Page 188 Section 10: Management and Configuration AXIS 5570e/AXIS 5670e User’s Manual Software Default A Software Default will reset all print server parameters and settings to their default values except: • Node address (NODE_ADDR.) • IP Address (INT_ADDR.) • DHCP enabled (DHCP_ENB) •...
Page 189: Using Axis Thinwizard For Print Server Management
To install, follow the instructions given by the Installation Wizard. During the installation, you will be asked to enter a user id and a password — these will be used when logging in to AXIS ThinWizard, so please take a note of them.
Page 190 Section 10: Management and Configuration AXIS 5570e/AXIS 5670e User’s Manual 4. The AXIS ThinWizard start page now appears in the Web browser. Enter the user id and password you specified during installation and click Log in. 5. The AXIS ThinWizard interface appears:...
Page 191 All AXIS servers included in the network group appear in the window. 3. Click the link of the AXIS 5570e/AXIS 5670e to access its internal Web page. 4. The ‘Srv’ and ‘Dev’ columns show the status of your print servers and printers.
Page 192: Using Ftp For Print Server Management
3. Download the config file to your host by typing: get config 4. Edit the file using your preferred text editor. 5. Save the config file to the AXIS 5570e/AXIS 5670e by typing: put config CONFIG Notes: • It is important that the destination file is specified in capital letters.
Page 193 AXIS 5570e/AXIS 5670e User’s Manual Section 10: Management and Configuration Example: > ftp npserver connected to npserver. 220 AXIS 5570e/AXIS 5670e FTP Print Server v6.30 Dec 16 2000 ready. Name (npserver:thomas): root 331 User name ok, need password (not visible)
Page 194 Off-line, or Printing), number of bytes printed, elapsed time and off- line time. Follow the instructions below to view the account file using FTP: 1. Log in to the AXIS 5570e/AXIS 5670e by typing: in a DOS windows ftp <host name>...
Page 195: Using Telnet
AXIS 5570e/AXIS 5670e User’s Manual Section 10: Management and Configuration Using Telnet Having assigned an IP address to your AXIS 5570e/AXIS 5670e, as described in Setting the IP address, on page 24, you can manage your AXIS 5570e/AXIS 5670e using the Telnet protocol.
Page 196 Example: > telnet npserver Trying 192.36.253.96... Connected to npserver. Escape character is ‘^]’. AXIS 5570e/AXIS 5670e TELNET Print Server v6.30 Dec 16 2000 AXIS 5570e/AXIS 5670e network login: root (not visible) Password: pass AXIS 5570e/AXIS 5670e TELNET Print Server v6.30 Dec 16 2000 Root>...
Page 197 Printing Hexdumps The AXIS 5570e/AXIS 5670e allows you to record a trace of the communication between the AXIS 5570e/AXIS 5670e and the host. The AXIS 5570e/AXIS 5670e supports hexdump printing for the SNA, TN3270E, TN5250E, LPR/LPD and Raw TCP/IP printing protocols.
Page 198 2. Enter the user id and the password. (The default entries are root pass 3. Enable the AXIS 5570e/AXIS 5670e to hexdump mode by typing: snahexdump 4. Select Start Logging from the Terminal menu in the Telnet window. Specify a file name and select the folder where you want to save the file.
Page 199: Using Snmp
Objects are contained in data bases called MIBs (Management Information Base), where MIB-II is a standard database. The AXIS 5570e/AXIS 5670e supports all relevant parts of MIB-II and also includes a private enterprise MIB. Refer to The AXIS MIB, on page 200.
Page 200 Section 10: Management and Configuration AXIS 5570e/AXIS 5670e User’s Manual The AXIS MIB The AXIS MIB contains a large number of objects which may be categorized as follows: • Menu objects - used for viewing and changing the AXIS 5570e/AXIS 5670e configuration from the NMS program. Refer to The Parameter List, on page 295.
Page 201: Using Novell Utilities
Printer Status The Printer Status menu, detailed below, shows the status of an active print job serviced by an AXIS 5570e/AXIS 5670e network print server. It displays detailed information concerning the active job including, Print Queue, print job description, size of print file, percentage of job completed, etc.
Page 202 Print Layout You can view installed AXIS 5570e/AXIS 5670e Network Print Servers and their relative print queues for any NetWare Organizational Unit. You can also display summary information by right-clicking on the printer object you want to examine.
Page 203: Configuring The Print Server From An Ibm Host
Configuring the Print Server from an IBM host Once communication with an IBM host has been established, all the AXIS 5570e/AXIS 5670e parameters can be edited by printing a file containing special configuration commands. To start the configuration, the command is entered in the file.
Page 204 Section 10: Management and Configuration AXIS 5570e/AXIS 5670e User’s Manual Select the PCL5 printer driver and disable the NetWare protocol: (If you have not changed the default %CONFIG+ password; password (pass), the password is optional) PRDRIVER = PCL5; %CONFIG++ NETW_ENB = NO;...
Page 205: Configuration Possibilities
AXIS 5570e/AXIS 5670e User’s Manual Section 11: Configuration Possibilities Section 11 Configuration Possibilities This section describes some special features offered by the AXIS 5570e/AXIS 5670e: Autodetect Printer Type, on page 205 AutoIP, on page 206 E-mail Notification, on page 206...
Page 206: Autoip
Section 11: Configuration Possibilities AXIS 5570e/AXIS 5670e User’s Manual AutoIP In the absence of an IP address management mechanism such as DHCP, the print server will receive a temporary IP address automatically over AutoIP, a method which enables the host to automatically take a linklocal IPv4 address.
Page 207: Ipp (Internet Printing Protocol)
IPP (Internet Printing Protocol) Printing over the Internet with IPP (Internet Printing Protocol) is possible with the AXIS 5570e/AXIS 5670e. IPP is an industry standard that allows users to print to remote printers across the Internet. With IPP, a user with an Internet connection can send a document to any printer which is connected to the Internet.
Page 208 • the 1.1 standard, which uses an ipp:// address scheme Example using a If “axisps” is the host name of the AXIS 5570e/AXIS 5670e, "631" is Host Name the port number and "USB1" is the local printer port name, then the in the 1.0 Standard:...
Page 209 • For UNIX/Linux: CUPS (can be downloaded from the Common Unix Printing System Web site at www.cups.org). If you wish to print using iPrint over IPP, the following Axis snap-in tool is available from www.axis.com/techsup => Select Software: • AXIS IPP Gateway Comfiguration Snap-in for i-Print in NetWare 5.x.
Page 210 File | Print). 2. When you press Print, the print job is sent over the Internet to the AXIS 5570e/AXIS 5670e, which then forwards the print job to the destination printer. 3. The recipient of the print job can collect the print job at the destination printer.
Page 211 2. When you press Print, the print job is sent over the Internet/WAN to the AXIS 5570e/AXIS 5670e, which then forwards the print job to the destination printer. 3. The recipient of the print job can collect the print job at the...
Page 212 Section 11: Configuration Possibilities AXIS 5570e/AXIS 5670e User’s Manual Adding an IPP Printer 1. Install the Internet Printer Connection software from Hewlett to your Printer List in Packard (can be downloaded from the Hewlett Packard Web site) Windows NT on your computer.
Page 213 AXIS 5570e/AXIS 5670e User’s Manual Section 11: Configuration Possibilities 5. In the Available Ports window, click Add Port: 6. The Printer Ports dialog will appear, showing a list of Available Printer Ports. 7. Choose The HP Internet Printer Connection Port and click New Port.
Page 214 AXIS 5570e/AXIS 5670e User’s Manual 9. In the IP Address, Host Name or URL field, type the http:// address of the AXIS 5570e/AXIS 5670e to which the destination printer is connected. The URL will automatically appear in the Port Name field as well: Example: http://171.16.5.218:631/LPT1 if you want to address the parallel...
Page 215 AXIS 5570e/AXIS 5670e User’s Manual Section 11: Configuration Possibilities 12. Next, choose a suitable driver for the destination printer and install it. Click Next 13. You will be asked if you want the newly added printer to be your default printer and if you want to share the printer on your network with other users.
Page 216 Adding an IPP printer to your printer list is described below. 2. When you press Print, the print job is sent over the Internet to the AXIS 5570e/AXIS 5670e, which then forwards the print job to the destination printer.
Page 217 AXIS 5570e/AXIS 5670e User’s Manual Section 11: Configuration Possibilities 3. The recipient of the print job can collect the print job at the destination printer. 1. Choose File | Print from the document you wish to print. Adding an IPP Printer to your Printer List in 2.
Page 218 Section 11: Configuration Possibilities AXIS 5570e/AXIS 5670e User’s Manual 6. The Installation Wizard will ask you to select a printer driver corresponding to the destination printer. Select the printer driver from the list and click OK. 7. The Wizard will ask you if you want the printer to be your default destination printer.
Page 219 AXIS 5570e/AXIS 5670e User’s Manual Section 11: Configuration Possibilities 8. The new printer is added to your Select Printer window: 9. You are now ready to print using IPP: specify your new destination printer from the printer list and click Print.
Page 220: Logical Printers For Customized Printing
AXIS 5570e/AXIS 5670e User’s Manual Logical Printers for Customized Printing The AXIS 5570e/AXIS 5670e has a powerful facility for altering the print data. This means that your desired print format can be realized on any type of printer. The following actions can be invoked from the print server: •...
Page 221 • The examples should only be viewed as suggestions how to configure the logical printers. You should, of course, configure them according to the needs of your network. • In the Parameter List chapter of this manual, you can find a complete list of the AXIS 5570e/AXIS 5670e parameters.
Page 222 Section 11: Configuration Possibilities AXIS 5570e/AXIS 5670e User’s Manual 3. Set the parameter Physical Port to USB1. 4. Set the parameter Character Set Conversion to ISO>IBM. 5. Click the OK button. 6. Select the PR2 tab. 7. Set the parameter Physical Port to USB1.
Page 223 AXIS 5570e/AXIS 5670e User’s Manual Section 11: Configuration Possibilities Example: You have an HP LaserJet printer with dual trays, and want to print on pre-printed forms when using the logical printer PR4. The standard forms are taken from the lower tray, and the pre- printed forms are taken from the upper tray.
Page 224 Section 11: Configuration Possibilities AXIS 5570e/AXIS 5670e User’s Manual 1. From the print server’s internal Web page, select Admin | Logical Printers. 2. Select the PR1 Web page. 3. Enter the string 01 0A 02 0D 0A in the String Substitutions text field.
Page 225 1B 59 the new printer command Click the OK button. Note: Extensive use of string substitutions will naturally decrease the throughput rate of the AXIS 5570e/AXIS 5670e. ASCII to Postscript The AXIS 5570e/AXIS 5670e logical printers can translate ASCII print Conversion data into PostScript format.
Page 226 Section 11: Configuration Possibilities AXIS 5570e/AXIS 5670e User’s Manual Activate your desired filter by setting the Printer Language Translation (PRx_FILT.) parameter. Example: Follow the instructions below to convert ASCII print data to PostScript for logical printer PR2: 1. From the print server’s internal Web page, select Admin | Logical Printers.
Page 227 AXIS 5570e/AXIS 5670e User’s Manual Section 11: Configuration Possibilities The PostScript font can be any font that is installed in the printer. If no font is specified, Courier will be used. Example: Follow the instructions below to set the PostScript parameters for logical printer PR2: 1.
Page 228 Section 11: Configuration Possibilities AXIS 5570e/AXIS 5670e User’s Manual 1. From the print server’s internal Web page, select Admin | Logical Printers. 2. Select the PR1 tab. 3. Set the Physical Port parameter to USB1. 1. Set the Secondary Printer parameter to PR3.
Page 229 AXIS 5570e/AXIS 5670e User’s Manual Section 11: Configuration Possibilities Read Back of The AXIS 5570e/AXIS 5670e support bi-directional printing. The information information from the printer is read back on the parallel port when the parameter Read Back Port (PRx_IN.) has the default setting of AUTO.
Page 230: Network Speed
Section 11: Configuration Possibilities AXIS 5570e/AXIS 5670e User’s Manual Network Speed With the Network Speed parameter you can manually specify the speed at which you will send and receive network packages. You can change the Network Speed setting to correspond to the type of network you are using (10 or 100 Mbit).
Page 231: Secure Web Services - Ssl/Tls
AXIS 5570e/AXIS 5670e User’s Manual Section 11: Configuration Possibilities Secure Web Services — SSL/TLS In a new and unconfigured AXIS 5570e/AXIS 5670e, SSL/TLS is disabled. Certificates To use SSL/TLS you have to create or obtain a digital certificate. There are two kinds of certificates: self-signed certificates and third party certificates.
Page 232 Section 11: Configuration Possibilities AXIS 5570e/AXIS 5670e User’s Manual Enter the data asked for: Example • Country Name: : US Example • State or Province Name: : California Example • Locality Name: : Los Angeles Example: • Organization Name: Printers Inc Example: •...
Page 233 AXIS 5570e/AXIS 5670e User’s Manual Section 11: Configuration Possibilities Click Finish and the print server will generate a public/private key pair as well as the self-signed certificate itself (this process will take a few minutes) and store these data in the print server. When the certificate is generated, the print server automatically loads it into your present browser session.
Page 234 Disabling Protocols To further increase security, you must disable protocols that are considered insecure; • FTP (used by AXIS ThinWizard. If FTP is disabled, AXIS ThinWizard can not function properly.) • Telnet • Auto-IP •...
Page 235 AXIS 5570e/AXIS 5670e User’s Manual Section 11: Configuration Possibilities Important: To ensure maximum security, it is highly recommended that you change your Administrator password after generating a certificate and disabling insecure protocols! This is done from Admin | General Settings | Change => | General | Root Password.
Page 236: Upgrading The Firmware
Section 12: Upgrading the Firmware AXIS 5570e/AXIS 5670e User’s Manual Section 12 Upgrading the Firmware Upgrading the Firmware You can upgrade the AXIS 5570e/AXIS 5670e firmware using one of the following methods: • AXIS ThinWizard (TCP/IP) • From the print server’s internal Web pages (TCP/IP) •...
Page 237 Click Next >. 4. Enter the default User ID and Password of the servers you selected in the previous step. Select whether you want AXIS ThinWizard to verify the password immediately or when the upgrading job has started, by checking the appropriate box. Click Next >.
Page 238 5670e before you can use this upgrading method. Caution! Be careful not to interrupt the file transfer. If the transfer is interrupted, the AXIS 5570e/AXIS 5670e may have to be re-initialized by your dealer. The objective of this example is to upgrade a print server with firmware version 6.41 to firmware version 6.42.
Page 239: Obtaining The Software
AXIS 5570e/AXIS 5670e User’s Manual Section 12: Upgrading the Firmware 6. Connect to the print server using ftp. Type ftp 10.13.4.105 (Example using print server IP address 10.13.4.105) 7. Type root after "User:", press Enter. Type pass after "Password:" (your entry will not be visible) press Enter.
Page 240: Sna Parameter Overview
An overview of how parameters are mapped during the auto- configuration process is also provided. Refer to the Parameter List document on www.axis.com for a complete description of the Axis Print server parameters. Communication Parameters In most environments, the basic communication parameters need to be customized in order to establish a communication link to the host system.
Page 241 AXIS 5570e/AXIS 5670e User’s Manual Section 13: SNA Parameter Overview Parameter Summary The following tables summarize SNA host communication parameters that must be considered when installing the AXIS 5570e/AXIS 5670e. The parameters are presented as: • Common Mainframe and AS/400 parameters •...
Page 242 LU Name Axxxxxxx 5494 only Description - Axxxxxxx, where "xxxxxxx" is the last 7 characters of the AXIS 5570e/AXIS 5670e serial number, in reverse order, e.g. if s.no. = 00 40 8C 1B 06 D4 the default LU Name = A4D60B1C.
Page 243: Updating Parameters
This is most easily done from the internal web pages of your AXIS 5570e/AXIS 5670e. To set the parameters using a Web browser, you first need to assign an IP address to the AXIS 5570e/AXIS 5670e. For instructions on how to do this, refer to Setting the IP address, on page Alternatively, you can update the parameters via FTP, TFTP or by using extended IBM printer emulation.
Page 244 Section 13: SNA Parameter Overview AXIS 5570e/AXIS 5670e User’s Manual To set the parameters to their default values, enter the following in your document and print it. %CONFIG+ password (If you have not changed the default password (pass), the password is optional.) PRDRIVER = PCL5;...
Page 245: Auto-Configuration And Mapping
Printer device #2 Logical Printer #3 Printer device #3 Illustration of the configuration created in the AS/400 and the mapping to the AXIS 5570e/AXIS 5670e as a result of the auto-configuration Printer Device Through auto-configuration, the APPC controller, APPC device, RWS...
Page 246 Section 13: SNA Parameter Overview AXIS 5570e/AXIS 5670e User’s Manual Printer devices will be named "A201PRT01", A201PRT02", A201PRT02"… The designation "PRTnn" corresponds to the logical printers in the Print Server, i.e. printer device "A201PRT01" will be mapped to Logical Printer #1. By default, all Logical Printers are mapped to the Physical Port LPT1.
Page 247: Sna Gateways
3745 Communications Controller, IBM 3174 Establishment Controller, IBM 3172 LAN Interconnect Controller, etc. You need to set up at least one PU and LU definition for each AXIS 5570e/AXIS 5670e on the host, as described in the VTAM section. When attaching an AXIS 5570e/AXIS 5670e to a remote pass- through gateway, you need to set the mapping of SDLC or sub- channel address to MAC address in the gateway.
Page 248 When an AXIS 5570e/AXIS 5670e is attached to this type of gateway, you can map the chosen AXIS 5570e/AXIS 5670e LU to any host LU you like. This way, several print servers may be accessed through the same gateway.
Page 249 AXIS 5570e/AXIS 5670e User’s Manual Section 14: SNA Gateways 5. Configure PU and LUs. On the Configure PU Profile screen you can set default LU attributes, starting dependent LU address, number of dependent LUs, give CP a name, enable off-line test...
Page 250 Section 14: SNA Gateways AXIS 5570e/AXIS 5670e User’s Manual 3. Select host connection and assign one or more DownStream LUs to it. 4. Select downstream connection and associate the DownStream LUs (from step 3) with that connection. 5. If necessary, reorder the DownStream LU numbers, that is, the LU numbers used by the downstream system.
Page 251: Extended Ibm Printer Emulation
The String Substitution function searches the output data stream for specified sequences of AIC characters (Match Strings), and substitutes them with other sequences (Substitute Strings). Up to 128 pairs of Match/Substitute Strings may be defined. AIC (AXIS Internal Codes) are listed in the AXIS Network Print Server Technical Reference.
Page 252 The word underline is underlined You can also use quoted text. Bar Codes The bar code function provides easy access to a range of standard bar code types resident in the AXIS 5570e/AXIS 5670e. Bar codes can only be printed on PCL printers.
Page 253 AXIS 5570e/AXIS 5670e User’s Manual Section 15: Extended IBM Printer Emulation Before the bar codes can be printed, a bar code format has to be defined. This format sets the type and size of the bar code to be printed. Up to 16 formats can be predefined. The definitions are made by setting up the BAR parameter.
Page 254 0123 4565 0123 4565 AXIS Cobra products The AXIS 5570e/AXIS 5670e supports a subset of the extended printer compatibility emulation syntax of the AXIS Cobra products, including the bar codes syntax. For more information, please refer to the AXIS Network Print...
Page 255: Ibm Fonts
Font Selection, Fonts can be indirectly selected by the IBM system using pitch Coax Printer selection (CPI). In order to gain full access to the fonts the AXIS Emulations 5570e/AXIS 5670e offers an alternative font selection command. Please note that matrix printers only support a few fonts.
Page 256 Section 16: IBM Fonts AXIS 5570e/AXIS 5670e User’s Manual Available Fonts The fixed pitch fonts are not scalable. If a Point Size is specified, it will be used to compress or expand the character spacing. (%/FONT 11,105; will compress the 10 CPI font to 10.5 CPI without changing the size of the characters).
Page 257 AXIS 5570e/AXIS 5670e User’s Manual Section 16: IBM Fonts FGID IBM Font Name Gothic Text 12 Gothic Italic 12 Gothic Bold 12 Serif Text 12 Serif Italic 12 Serif Bold 12 Math Symbol 12 Script Pitch 12 CPI Fonts Courier 12...
Page 258 Section 16: IBM Fonts AXIS 5570e/AXIS 5670e User’s Manual Pitch 20 CPI Fonts Gothic Text 20 Pitch 25 CPI Fonts Gothic Text 25 Pitch 26.7 CPI Fonts Gothic Text 27 FGID IBM Font Name Boldface Italic Modern Boldface Essay Proportional PSM Fonts...
Page 259 AXIS 5570e/AXIS 5670e User’s Manual Section 16: IBM Fonts FGID IBM Font Name 3840 CG Times 3841 CG Times Bold 3842 CG Times Italic 3843 CG Times Bold Italic 3844 CG Omega 3845 CG Omega Bold 3846 CG Omega Italic...
Page 260 Section 16: IBM Fonts AXIS 5570e/AXIS 5670e User’s Manual 3863 Garamond Kursiv 3864 Garamond Kursiv Halbfett 3865 Marigold 3866 Albertus Medium 3867 Albertus Extra Bold 3868 Arial 3869 Arial Bold Proportional Typographic Fonts 3870 Arial Italic (Scalable - User Defined FGIDs)
Page 261 AXIS 5570e/AXIS 5670e User’s Manual Section 16: IBM Fonts 16951 Century Schoolbook 16971 Century Schoolbook Bold 17079 Century Schoolbook Italic 17099 Century Schoolbook Bold Italic 33335 Optima 33355 Optima Bold 33463 Optima Italic 33483 Optima Bold Italic 33591 Futura Book (cont.)
Page 262: Ibm Print Formatting
Section 17: IBM Print Formatting AXIS 5570e/AXIS 5670e User’s Manual Section 17 IBM Print Formatting This appendix provides general parameter information relating to non-IPDS IBM print formatting. IBM Printer Emulation The following tables display the valid printer emulations that can be used in coax and twinax printer emulations.
Page 263 AXIS 5570e/AXIS 5670e User’s Manual Section 17: IBM Print Formatting Twinax Printer Emulations AS/400 Parameter Printer Emulation Default Printer Description Name Options 3812_tx IBM 3812 model 1 and 2 page printer IBM 3816 models 01S and 01D, page 3816_tx printer with 5219 diskette...
Page 264 Section 17: IBM Print Formatting AXIS 5570e/AXIS 5670e User’s Manual Coax mode Mainframe Parameter Name Default Value Description Value User defined system language US English, Portuguese Alter- Korean (Jamo) nate and Canadian Bilingual International Set 1 Chinese Canadian French Thai...
Page 265 Enter. The Code page value is the value of the system language (see the table above). • Visit the Axis web site http://www.axis.com/ for more information on how to edit the character translation tables Page Formats You can configure the formats for each paper bin separately from the AXIS 5570e/AXIS 5670e internal web pages.
Page 266 Section 17: IBM Print Formatting AXIS 5570e/AXIS 5670e User’s Manual Paper Size The parameters take two values, orientation and paper size. The following tables describe the paper sizes that can be used in coax and twinax mode. Printer Emulation Parameters...
Page 267 ASCII Printer Driver This parameter should match the printer type you have connected to your AXIS 5570e/AXIS 5670e. Select the correct printer type from the AXIS 5570e/AXIS 5670e internal web pages. Click admin | IBM Emulators | Detailed View for SCS/IPDS Emulator Configuration.
Page 268: Ipds Overview
IPDS Parameter Settings Before printing IPDS data streams, the basic parameters should be set. This is done from the AXIS 5570e/AXIS 5670e web pages under IBM Emulators | Detailed view (IBM IPDS Emulator Settings) where you can configure the common parameters of the IPDS emulator and IBM Emulators | Detailed view (SCS/IPDS Emulator Configurations) where you can configure the settings for each session.
Page 269 AXIS 5570e/AXIS 5670e User’s Manual Section 18: IPDS Overview Code page System language US English, Portuguese Alternate and Canadian Bilingual International set 1 Symbols set 7 Canadian French Austrian/German Belgian Brazilian Danish/Norwegian Swedish/Finnish Italian Japanese English Portuguese Spanish and Spanish Speaking...
Page 270 Section 18: IPDS Overview AXIS 5570e/AXIS 5670e User’s Manual The Euro character is implemented in the Code Pages 1140 - 1149: Code page System language - Latin 1 EBCDIC Publishing 1140 US English, Canadian English, Canadian French, Netherlands, Brazil, Portugal...
Page 271 AXIS 5570e/AXIS 5670e User’s Manual Section 18: IPDS Overview Code page System language - Latin 2/3/4/5 EBCDIC and ASCII Croatian, Czech, East German, Hungarian, Polish, Romanian, Slovak, Slovenian Latin 2 ISO/ ANSI 8 Bit Latin 3 Multilingual PC Latin 3 Multilingual...
Page 272 Section 18: IPDS Overview AXIS 5570e/AXIS 5670e User’s Manual The basic IPDS parameters are set from the IBM Emulators | Detailed IPDS Configuration view (IBM IPDS Emulator Settings) page: Enter the configuration settings for the parameters described below. When you are finished, click OK at the bottom of the page to save your settings to the print server.
Page 273 AXIS 5570e/AXIS 5670e User’s Manual Section 18: IPDS Overview Optimize Duplex Use this option to optimize duplex print jobs. Optimization means that sheets are printed in simplex if the reverse side of the sheet is empty, resulting in higher throughput.
Page 274 A downloaded 240 dpi font may appear jagged when printed on a Smoothing 300 dpi printer. The AXIS 5570e/AXIS 5670e uses a font smoothing feature to enhance the appearance of these fonts. The font smoothing may be disabled if you want to speed up the font loading or if your printer has insufficient PostScript virtual memory.
Page 275 AXIS 5570e/AXIS 5670e User’s Manual Section 18: IPDS Overview Click the IPDS PCL Driver Settings tab and enter the configuration IPDS PCL Configuration settings for the parameters as described below. When you are finished, click OK at the bottom of the page to save your settings to the print sever.
Page 276: Ipds Fonts
Section 18: IPDS Overview AXIS 5570e/AXIS 5670e User’s Manual IPDS Fonts This section describes how IPDS fonts are handled by the AXIS 5570e/AXIS 5670e. There are two different approaches to font handling: • downloading fonts from the host. • using fonts that are already resident in the printer.
Page 277: Immediate Font Substitutions
5570e/AXIS 5670e. The substitution table depends on the selected IBM printer emulation. Unsupported Fonts A selection of an unsupported FGID value will result in a substitution to a default font. The AXIS 5570e/AXIS 5670e uses the same default fonts as the emulated IBM printers.
Page 278: Typographical Fonts
40 (6 points). Scalable Fonts If the selected font width (point size) is not available for the selected FGID, the AXIS 5570e/AXIS 5670e will set a point size in one of the following ways depending on the font: Times Roman,...
Page 279: Dbcs Support
Shift - JIS China 5x27_005_TX AXIS 5570e/AXIS 5670e Double-byte Character Tables The AXIS 5570e/AXIS 5670e supports SNA DBCS printing in IBM 5494 Important! emulation only. Configuring the AS/400 Host, 5494 CU mode Follow the instructions below to configure the AS/400 Host for DBCS support: 1.
Page 280: Configuring The Axis 5570E/Axis 5670E
1. Start a Web browser, e.g. Internet Explorer or Netscape Navigator. 2. Enter the IP address or the host name of the AXIS 5570e/AXIS 5670e in the location field and press the Enter key on your keyboard. The internal Web pages of the AXIS 5570e/AXIS 5670e...
Page 281: Verifying The Communications Link
Default fonts will be changed when switching printer emulations. Verifying the Communications Link Having configured the AS/400 host AXIS 5570e/AXIS 5670e in accordance with the above, verify that the communications link is functioning correctly by following instructions 1-4 detailed in...
Page 282: Amending Device Features
Section 19: DBCS Support AXIS 5570e/AXIS 5670e User’s Manual Amending Device Features After automatic setup, it may be necessary to change the Device features and Last Code Point of the printer device. Failure to do so may cause corruption within your print data.
Page 283: Extended Ibm Printer Emulation
<SO>(SCS Shift Out Control Code) Example (with DBCS mode before entering extended emulation) Font Tables The following tables define the DBCS font types supported in the AXIS 5570e/AXIS 5670e (5494 CU Mode): DBCS FONTS (Japan) DBCS FONTS (China) FGID IBM Font Name...
Page 284 Section 19: DBCS Support AXIS 5570e/AXIS 5670e User’s Manual 50005 50105 MS Mincho 15 CPI SimSun 15 CPI 50017 50117 MS Mincho 15 CPI SimSun 15 CPI 50009 50109 MS Mincho 17.1 CPI SimSun 17.1 CPI 50020 50120 MS Mincho 17.1 CPI...
Page 285 AXIS 5570e/AXIS 5670e User’s Manual Section 19: DBCS Support 50038 50138 HanYang 14.3 CPI Compst 14.3 CPI 50049 50149 HanYang 14.3 CPI Compst 14.3 CPI 50034 50134 HanYang 15 CPI Compst 15 CPI 50035 50135 HanYang 15 CPI Compst 15 CPI...
Page 286: Digital Copier Support
AXIS 5470e to. Copier Duplex The AXIS 5470e supports duplex printing i.e. printing on both sides of the paper. The options in the drop-down list are: Off i.e. the duplex printing option is not activated (default).
Page 287 Please refer to the documentation of your digital copier for more information on these features. Copier Hole Punch The AXIS 5470e supports hole punching with the following options: Off i.e. the hole punching option is not activated (default). •...
Page 288: Test Button
AXIS 5570e/AXIS 5670e User’s Manual Section 21 Test Button The test button is located on the front right hand side of the AXIS 5570e/AXIS 5670e and is used for: • Printing a test page, checking the connection to the printer.
Page 289 AXIS 5570e/AXIS 5670e User’s Manual Section 21: Test Button 4. Restart the AXIS 5570e/AXIS 5670e by disconnecting and reconnecting the external power supply Important! All parameters are reset to their default values when performing a factory default with the test button.
Page 290: Technical Specifications
Section 22: Technical Specifications AXIS 5570e/AXIS 5670e User’s Manual Section 22 Technical Specifications Refer to the ‘Parameter List’ document on www.axis.com for a complete description of the Axis print server parameters. Supported Printers: Support for all printers and copiers except host-based printers such as Windows GDI.
Page 291 AXIS 5570e/AXIS 5670e User’s Manual Section 22: Technical Specifications Supported systems: • Microsoft Windows: 98, Me, NT, 2000, XP and 2003 Server • Novell NetWare: 3.X, 4.X, 5.X, 6.X. Supports bindery and NDS mode. Supports user messages and printer status. NDPS supported over IP and IPX.
Page 292 Management firmware upgrading of multiple units • Internal web pages for installation, configuration, monitoring and firmware upgrading • SNMP-MIB II compliant (RFC 1213), Axis private enterprise MIB included • Netware: full PCONSOLE, NWAdmin, ConsoleOne and iPrint- iManager support Firmware Upgrade...
Page 293 115.200 baud • Bi-directional support for Apple EtherTalk, • Reverse Telnet and PROS Hardware: • Processor: AXIS Etrax 100LX 32-bit 100 MHz RISC • Memory: 2 MB Flash, 8 MB RAM Front Panel • 2 LED indicators: Power and Network •...
Page 294 Section 22: Technical Specifications AXIS 5570e/AXIS 5670e User’s Manual Approvals • EMC: EN 55022/1998, EN 55024:1998, EN 61000-3-2, EN 61000- 3-3, VCCI Class B, CTICK AS/NZS 3548, Compliance to FCC part 15 Subpart B, Class B • Safety: EN 60950...
Page 295: The Parameter List
After you have changed them, most parameters take effect for the next print job. If Requires Restart appears in a parameter description, you must restart the AXIS 5570e/AXIS 5670e, before the new setting for that parameter takes effect. Please refer to Section 10 Management and Configuration, on page 180, for more information about how to change the parameters.
Page 296 Section 23: The Parameter List AXIS 5570e/AXIS 5670e User’s Manual TN3270E_IR. : 0 TN3270E_1. : OFF, 0 0 0 0, 23, PR1, 1, AXPR1 TN3270E_2. : OFF, 0 0 0 0, 23, PR2, 2, AXPR2 TN3270E_3. : OFF, 0 0 0 0, 23, PR3, 3, AXPR3 TN3270E_4.
Page 297 AXIS 5570e/AXIS 5670e User’s Manual Section 23: The Parameter List RARP_ENB. : YES WINS_ENB. : YES WINS_ADDR1. : 0 0 0 0 WINS_ADDR2. : 0 0 0 0 NBT_SCOPE_ID. : DNS_ENB. : YES DNS_ADDR1. : 0 0 0 0 DNS_ADDR2. : 0 0 0 0 DOMAIN_NAME.
Page 298 Section 23: The Parameter List AXIS 5570e/AXIS 5670e User’s Manual SYS_NAME. : SNMP_AUT. : DISABLE (DISABLE, ENABLE) TRAP_PRT. : DISABLE (DISABLE, ENABLE) --- NetWare Menu NETW_ENB. : YES NETW_TRANSPORT_PROTOCOL. : DUAL_STACK (IPX_ONLY, IP_ONLY, DUAL_STACK) NDPS. : TCP_AND_SPX (TCP_AND_SPX, TCP_ONLY, SPX_ONLY, DISABLED) JOB_CHECK_DELAY.
Page 299 AXIS 5570e/AXIS 5670e User’s Manual Section 23: The Parameter List PSERVER_BINDERY16. : NPRINTER1. : NPRINTER2. : NPRINTER3. : NPRINTER4. : NPRINTER5. : NPRINTER6. : NPRINTER7. : NPRINTER8. : --- NetBIOS/NetBEUI Menu LSLM_ENB. : YES NB_FR_TYPE. : FR_802_2 (FR_AUTO, FR_802_2, FR_DIX) LPRINT_1.
Page 300 Section 23: The Parameter List AXIS 5570e/AXIS 5670e User’s Manual --- AppleTalk Menu ATLK_ENB. : YES ATK_ZONE. : ZONER_EN. : YES ATK_FONT. : DEFAULT (DEFAULT, 35N, ALL) AUTO_DT_PRIN. : NO APRINT_1. : AXIS181E6A_LPT1 ATYPE_1. : LaserWriter ALOGIC_1. : PR1 (PR1, PR2, PR3, PR4, PR5, PR6, PR7, PR8, LPT1, USB1) BINARY_TYPE_1.
Page 301 AXIS 5570e/AXIS 5670e User’s Manual Section 23: The Parameter List --- Printer2 Menu PR2_OUT. : USB1 (NONE, LPT1, USB1) PR2_NAME. : PR2_SCND. : PR2 (PR1, PR2, PR3, PR4, PR5, PR6, PR7, PR8) PR2_WAIT. : YES PR2_IN. : AUTO (AUTO, NONE) PR2_BEF.
Page 302 Section 23: The Parameter List AXIS 5570e/AXIS 5670e User’s Manual PR3_FONT. : --- Printer4 Menu PR4_OUT. : USB1 (NONE, LPT1, USB1) PR4_NAME. : PR4_SCND. : PR4 (PR1, PR2, PR3, PR4, PR5, PR6, PR7, PR8) PR4_WAIT. : YES PR4_IN. : AUTO (AUTO, NONE) PR4_BEF.
Page 303 AXIS 5570e/AXIS 5670e User’s Manual Section 23: The Parameter List PR5_ORNT. : PORTR (PORTR, LANDS, R_PORTR, R_LANDS) PR5_FORM. : 66 0 100 60 30 50 PR5_FONT. : --- Printer6 Menu PR6_OUT. : USB1 (NONE, LPT1, USB1) PR6_NAME. : PR6_SCND. : PR6 (PR1, PR2, PR3, PR4, PR5, PR6, PR7, PR8) PR6_WAIT.
Page 304 Section 23: The Parameter List AXIS 5570e/AXIS 5670e User’s Manual PR7_DUMP. : NO PR7_SIZE. : A4 (A4, LETTER, LEGAL, EXECUT) PR7_ORNT. : PORTR (PORTR, LANDS, R_PORTR, R_LANDS) PR7_FORM. : 66 0 100 60 30 50 PR7_FONT. : --- Printer8 Menu PR8_OUT.
Page 305 AXIS 5570e/AXIS 5670e User’s Manual Section 23: The Parameter List U1_COMMENT. : U1_BIDIR. : AUTO (DISABLE, AUTO) U1_READT. : 3 --- IBM EMULATOR 1 PREMUL1. : 3816_CX (3287_CX, 3268_CX, 3262_CX, 4214_CX, 4224_CX, 4230_CX, 3812_CX, 3816S_CX, 3816_CX, 5224_TX, 5225_TX, 5256_TX, 4214_TX, 4230_TX, 3812_TX,...
Page 306 Section 23: The Parameter List AXIS 5570e/AXIS 5670e User’s Manual LPI2. : 6 (3, 4, 6, 8) CPI2. : 10 (5, 10, 12, 13.3, 15, 17, 18) DCPI2. : 5.0 (5.0, 6.0, 6.7, 7.5, 9.0) AUTORI2. : YES LM2. : 0, 0, 48 TM2.
Page 307 AXIS 5570e/AXIS 5670e User’s Manual Section 23: The Parameter List --- IBM EMULATOR 4 PREMUL4. : 3816_CX (3287_CX, 3268_CX, 3262_CX, 4214_CX, 4224_CX, 4230_CX, 3812_CX, 3816S_CX, 3816_CX, 5224_TX, 5225_TX, 5256_TX, 4214_TX, 4230_TX, 3812_TX, 3816S_TX, 3816_TX, 5X27_001_TX, 5X27_002_KS_TX, 5X27_002_KSSM_TX, 5X27_003_TX, 5X27_005_TX) SYSL4.
Page 308 Section 23: The Parameter List AXIS 5570e/AXIS 5670e User’s Manual LM5. : 0, 0, 48 TM5. : 26, 26, 74 LDSF5. : 100, 100, 70 DEFBIN5. : BIN1 (BIN1, BIN2, BIN3, BIN4, BIN5, BIN6, MANUAL, ENVELOPE, CONTINUOUS) PRDRIVER5. : PCL5 (USER, GENERIC, PCL4, PCL5, IBM_PRO, EPSON_FX, EPSON_FX_15CPI,...
Page 309 AXIS 5570e/AXIS 5670e User’s Manual Section 23: The Parameter List PASSTHR7. : NO MPL7. : 66, ENA MPP7. : 132, ENA LPI7. : 6 (3, 4, 6, 8) CPI7. : 10 (5, 10, 12, 13.3, 15, 17, 18) DCPI7. : 5.0 (5.0, 6.0, 6.7, 7.5, 9.0) AUTORI7.
Page 310 Section 23: The Parameter List AXIS 5570e/AXIS 5670e User’s Manual --- IBM SCS PAGE FORMAT PCORI. : NO DWSISO. : NO BIN1. : COR, LETTER, 0, 0 BIN2. : COR, LETTER, 0, 0 BIN3. : COR, LETTER, 0, 0 BIN4.
Page 311 AXIS 5570e/AXIS 5670e User’s Manual Section 23: The Parameter List --- IBM 3270 OPTIONS CASE. : DUAL (DUAL, MONO) BASCOL. : BLACK, ENA XSTRN. AUTNL. ADDNL. FFWPB. FFEOPB. NULSUP. FFCPOS. AFEOPB. --- IBM SCS EXTENDED EMULATION XEMUL. : YES WARN.
Page 312 Section 23: The Parameter List AXIS 5570e/AXIS 5670e User’s Manual --- SSTR -------- --- MSTR -------- --- IBM PRINTER DRIVER PRDRIVERBASE. : PCL5 (GENERIC, PCL4, PCL5, IBM_PRO, EPSON_FX, EPSON_FX_15CPI, EPSON_LQ, EPSON_LQ_1600K, EPSON_LQ_KS) SOJS. : 1B 45 1B 26 6C 30 4C EOJS.
Page 313 AXIS 5570e/AXIS 5670e User’s Manual Section 23: The Parameter List CSIZS. LAC. : HP_PCL (DISABLE, HP_PCL, EPSON_LQ) GRD. : HP_PCL (DISABLE, HP_PCL, EPSON_LQ) JOGS. : 1B 26 6C 31 54 SSUS. SBSET. : PC850 (ECMA94, LATIN9, PC437, PC850, PC852, PC857, PC858, PC874, PC891,...
Page 314 Section 23: The Parameter List AXIS 5570e/AXIS 5670e User’s Manual FONT. : 84, 98, DEFAULT,FIXED, 120, 0, UPRIGHT,MEDIUM,4099, FONT. : 85, 98, DEFAULT,FIXED, 120, 0, UPRIGHT,MEDIUM,4099, FONT. : 86, 98, DEFAULT,FIXED, 120, 0, UPRIGHT,MEDIUM,4099, FONT. : 87, 98, DEFAULT,FIXED, 130, 0, UPRIGHT,MEDIUM,4102, FONT.
Page 315 AXIS 5570e/AXIS 5670e User’s Manual Section 23: The Parameter List FONT. : 751, 100, DEFAULT,PROP, 0, 80, UPRIGHT,MEDIUM,4101, FONT. : 1051, 100, DEFAULT,PROP, 0, 100, UPRIGHT,MEDIUM,4101, FONT. : 1053, 100, DEFAULT,PROP, 0, 100, UPRIGHT,BOLD, 4101, FONT. : 1056, 100, DEFAULT,PROP, 0, 100, ITALIC,MEDIUM,4101, FONT.
Page 316 Section 23: The Parameter List AXIS 5570e/AXIS 5670e User’s Manual FONT. : 3861, 100, DEFAULT,PROP, 0, 0, UPRIGHT,MEDIUM,4197, FONT. : 3862, 100, DEFAULT,PROP, 0, 0, UPRIGHT,BOLD, 4197, FONT. : 3863, 100, DEFAULT,PROP, 0, 0, ITALIC,MEDIUM,4197, FONT. : 3864, 100, DEFAULT,PROP, 0, 0, ITALIC,BOLD, 4197, FONT.
Page 317 AXIS 5570e/AXIS 5670e User’s Manual Section 23: The Parameter List FONT. : 33591,100, DEFAULT,PROP, 0, 0, UPRIGHT,MEDIUM,16602, FONT. : 33601,100, DEFAULT,PROP, 0, 0, UPRIGHT,BOLD, 16602, FONT. : 33719,100, DEFAULT,PROP, 0, 0, ITALIC,MEDIUM,16602, FONT. : 33729,100, DEFAULT,PROP, 0, 0, ITALIC,BOLD, 16602, FONT.
Page 318 Section 23: The Parameter List AXIS 5570e/AXIS 5670e User’s Manual FONT. : 50010,100, PC942,PROP, 0, 76, UPRIGHT,MEDIUM,28752, 1B 28 31 39 4B 1B 26 74 33 31 50 FONT. : 50011,100, PC942,PROP, 0, 67, UPRIGHT,MEDIUM,28752, 1B 28 31 39 4B 1B 26 74 33 31 50 FONT.
Page 319 AXIS 5570e/AXIS 5670e User’s Manual Section 23: The Parameter List FONT. : 50032,100, PC891,PROP, 0, 120, UPRIGHT,MEDIUM,43088, 1B 28 31 39 48 1B 26 74 33 38 50 FONT. : 50033,100, PC891,PROP, 0, 108, UPRIGHT,MEDIUM,43088, 1B 28 31 39 48 1B 26 74 33 38 50 FONT.
Page 320 Section 23: The Parameter List AXIS 5570e/AXIS 5670e User’s Manual FONT. : 50048,100, PC891,PROP, 0, 80, UPRIGHT,MEDIUM,41040, 1B 28 31 39 48 1B 26 74 33 38 50 FONT. : 50049,100, PC891,PROP, 0, 101, UPRIGHT,MEDIUM,41040, 1B 28 31 39 48 1B 26 74 33 38 50 FONT.
Page 321 AXIS 5570e/AXIS 5670e User’s Manual Section 23: The Parameter List FONT. : 50081,100, PC904,PROP, 0, 76, UPRIGHT,MEDIUM,0, FONT. : 50082,100, PC904,PROP, 0, 67, UPRIGHT,MEDIUM,0, FONT. : 50083,100, PC904,PROP, 0, 56, UPRIGHT,MEDIUM,0, FONT. : 50100,100, PC903,PROP, 0, 144, UPRIGHT,MEDIUM,37058, 1B 28 31 38 43 1B 26 74 33 38 50 FONT.
Page 322 Section 23: The Parameter List AXIS 5570e/AXIS 5670e User’s Manual FONT. : 50115,100, PC903,PROP, 0, 120, UPRIGHT,MEDIUM,37058, 1B 28 31 38 43 1B 26 74 33 38 50 FONT. : 50116,100, PC903,PROP, 0, 108, UPRIGHT,MEDIUM,37058, 1B 28 31 38 43 1B 26 74 33 38 50 FONT.
Page 323 AXIS 5570e/AXIS 5670e User’s Manual Section 23: The Parameter List FONT. : 50137,100, PC891,PROP, 0, 101, UPRIGHT,MEDIUM,43088, 1B 28 31 38 48 1B 26 74 33 38 50 FONT. : 50138,100, PC891,PROP, 0, 101, UPRIGHT,MEDIUM,43088, 1B 28 31 38 48 1B 26 74 33 38 50 FONT.
Page 324: Axis 5670E
Section 23: The Parameter List AXIS 5570e/AXIS 5670e User’s Manual FONT. : 50153,100, PC891,PROP, 0, 56, UPRIGHT,MEDIUM,41040, 1B 28 31 38 48 1B 26 74 33 38 50 --- Email Menu EMAIL_NOTIFICATION. : YES REPLY_ADDRESS. : PAPER_JAM_ADDRESS. : OUT_OF_PAPER_ADDRESS. : TONER_LOW_ADDRESS.
Page 325 AXIS 5570e/AXIS 5670e User’s Manual Section 23: The Parameter List NODE_ID. : E0 78 1E 58 NODE_SAP. : $4 NWORK_NAME. : APPN LU_NAME. : A85E181C H1_SAP. : $4 H1_ADDR. : FF FF FF FF FF FF H1_NW_NAME. : APPN H1_MOD_NAME. : QRMTWSC H1_LU_NAME.
Page 326 Section 23: The Parameter List AXIS 5570e/AXIS 5670e User’s Manual TN3270E_8. : OFF, 0 0 0 0, 23, PR8, 8, AXPR8 --- TN5250E TN5250E_KA. : YES TN5250E_1. : OFF, 0 0 0 0, 23, PR1, 1, AXPR1, QSYSOPR, QSYS TN5250E_2. : OFF, 0 0 0 0, 23, PR2, 2, AXPR2, QSYSOPR, QSYS TN5250E_3.
Page 327 AXIS 5570e/AXIS 5670e User’s Manual Section 23: The Parameter List DOMAIN_NAME. : SLP_ENB. : YES SLP_SCOPE_LIST. : DEFAULT SMTP_SERVER. : FTP_ENB. : YES TELNET_ENB. : YES DEFAULT_RAW_TCP. : 9100-9102 (9100-9102, CLOSED) RTN_OPT. : NO PPR_PRSTAT. : NO RTN_PR1. : 5001, IPDS, 1 RTN_PR2.
Page 328 Section 23: The Parameter List AXIS 5570e/AXIS 5670e User’s Manual NDPS. : TCP_AND_SPX (TCP_AND_SPX, TCP_ONLY, SPX_ONLY, DISABLED) JOB_CHECK_DELAY. : 5 CONF_CHECK_DELAY. : 300 FR_802_3. : YES FR_ETH_2. : YES FR_802_2. : YES FR_SNAP. : YES NCP_BURST_MODE. : YES PSERVER_NDS_TREE. : PSERVER_NDS_FILESERVER.
Page 329 AXIS 5570e/AXIS 5670e User’s Manual Section 23: The Parameter List NPRINTER7. : NPRINTER8. : --- NetBIOS/NetBEUI Menu LSLM_ENB. : YES NB_FR_TYPE. : FR_802_2 (FR_AUTO, FR_802_2, FR_DIX) LPRINT_1. : AX181E58.LP1 LLOGIC_1. : PR1 (PR1, PR2, PR3, PR4, PR5, PR6, PR7, PR8, LPT1, COM1, LPT2) LPRINT_2.
Page 330 Section 23: The Parameter List AXIS 5570e/AXIS 5670e User’s Manual APRINT_2. : AXIS181E58_LPT2 ATYPE_2. : LaserWriter ALOGIC_2. : PR2 (PR1, PR2, PR3, PR4, PR5, PR6, PR7, PR8, LPT1, COM1, LPT2) BINARY_TYPE_2. : TBCP (TBCP, BCP, NONE) APRINT_3. : AXIS181E58_COM1 ATYPE_3.
Page 331 AXIS 5570e/AXIS 5670e User’s Manual Section 23: The Parameter List PR1_DC_STAP. : OFF (OFF, TOP_LEFT_SLANT, TOP_LEFT_HORIZONTAL, TOP_LEFT_VERTICAL, TOP_RIGHT, BOTTOM_LEFT, BOTTOM_RIGHT, TOP_DOUBLE, LEFT_DOUBLE, CENTER) PR1_DC_HOLE. : OFF (OFF, LONG_EDGE, SHORT_EDGE) PR1_DC_FOLD. : OFF (OFF, HALF_FOLD, Z_FOLD) PR1_DC_TRAY. : DEFAULT (DEFAULT, 1, 2, 3, 4, 5) PR1_DC_COP.
Page 332 Section 23: The Parameter List AXIS 5570e/AXIS 5670e User’s Manual PR2_DC_HOLE. : OFF (OFF, LONG_EDGE, SHORT_EDGE) PR2_DC_FOLD. : OFF (OFF, HALF_FOLD, Z_FOLD) PR2_DC_TRAY. : DEFAULT (DEFAULT, 1, 2, 3, 4, 5) PR2_DC_COP. : 1 --- Printer3 Menu PR3_OUT. : COM1 (NONE, LPT1, COM1, LPT2) PR3_NAME.
Page 333 AXIS 5570e/AXIS 5670e User’s Manual Section 23: The Parameter List PR3_DC_TRAY. : DEFAULT (DEFAULT, 1, 2, 3, 4, 5) PR3_DC_COP. : 1 --- Printer4 Menu PR4_OUT. : COM1 (NONE, LPT1, COM1, LPT2) PR4_NAME. : PR4_SCND. : PR4 (PR1, PR2, PR3, PR4, PR5, PR6, PR7, PR8) PR4_WAIT.
Page 334 Section 23: The Parameter List AXIS 5570e/AXIS 5670e User’s Manual --- Printer5 Menu PR5_OUT. : LPT1 (NONE, LPT1, COM1, LPT2) PR5_NAME. : PR5_SCND. : PR5 (PR1, PR2, PR3, PR4, PR5, PR6, PR7, PR8) PR5_WAIT. : YES PR5_IN. : AUTO (AUTO, NONE, COM1) PR5_BEF.
Page 335 AXIS 5570e/AXIS 5670e User’s Manual Section 23: The Parameter List PR6_OUT. : LPT2 (NONE, LPT1, COM1, LPT2) PR6_NAME. : PR6_SCND. : PR6 (PR1, PR2, PR3, PR4, PR5, PR6, PR7, PR8) PR6_WAIT. : YES PR6_IN. : AUTO (AUTO, NONE, COM1) PR6_BEF.
Page 336 Section 23: The Parameter List AXIS 5570e/AXIS 5670e User’s Manual PR7_SCND. : PR7 (PR1, PR2, PR3, PR4, PR5, PR6, PR7, PR8) PR7_WAIT. : YES PR7_IN. : AUTO (AUTO, NONE, COM1) PR7_BEF. PR7_STR. PR7_CSET. : NONE (NONE, ISO>IBM, 7UK>IBM, 7SW>IBM, 7GE>IBM, 7FR>IBM, 7ND>IBM, DEC>IBM)
Page 337 AXIS 5570e/AXIS 5670e User’s Manual Section 23: The Parameter List PR8_IN. : AUTO (AUTO, NONE, COM1) PR8_BEF. PR8_STR. PR8_CSET. : NONE (NONE, ISO>IBM, 7UK>IBM, 7SW>IBM, 7GE>IBM, 7FR>IBM, 7ND>IBM, DEC>IBM) PR8_FILT. : NONE (NONE, POSTSCR, AUTO_PS) PR8_AFT. PR8_DUMP. : NO PR8_SIZE. : A4 (A4, LETTER, LEGAL, EXECUT) PR8_ORNT.
Page 338 Section 23: The Parameter List AXIS 5570e/AXIS 5670e User’s Manual --- COM1 Menu C1_BAUDR. : 9600 (300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200) C1_NBITS. : 8 (7, 8) C1_PARIT. : NONE (NONE, ODD, EVEN) C1_STOPB. : 2 (1, 2) C1_HNDSH.
Page 339 AXIS 5570e/AXIS 5670e User’s Manual Section 23: The Parameter List IPDS_BIN1. : Letter, 0, 0 IPDS_BIN2. : Letter, 0, 0 IPDS_BIN3. : Letter, 0, 0 IPDS_BIN4. : Letter, 0, 0 IPDS_BIN5. : Letter, 0, 0 --- IBM IPDS PostScript Driver Settings PS_LFSM.
Page 340 Section 23: The Parameter List AXIS 5570e/AXIS 5670e User’s Manual IPDS_PREMUL1. : IPDS_4332 (IPDS_4224_C2, IPDS_4224_E3, IPDS_3812_2, IPDS_3812_2_00, IPDS_3816, IPDS_4028_1, IPDS_4028_2, IPDS_4312, IPDS_4317, IPDS_4324, IPDS_4332) IPDS_PRRES1. : 0 IPDS_SYSL1. : 37 (37, 256, 259, 260, 273, 274, 275, 277, 278, 280, 281, 282, 284, 285, 286,...
Page 341 AXIS 5570e/AXIS 5670e User’s Manual Section 23: The Parameter List IPDS_SYSL2. : 37 (37, 256, 259, 260, 273, 274, 275, 277, 278, 280, 281, 282, 284, 285, 286, 287, 288, 289, 290, 293, 297, 361, 420, 423, 424, 437, 500, 803, 819, 838, 852, 853, 857, 858,...
Page 342 Section 23: The Parameter List AXIS 5570e/AXIS 5670e User’s Manual IPDS_SOJS3. : IPDS_EOJS3. : PREMUL3. : 3816_CX (3287_CX, 3268_CX, 3262_CX, 4214_CX, 4224_CX, 4230_CX, 3812_CX, 3816S_CX, 3816_CX, 5224_TX, 5225_TX, 5256_TX, 4214_TX, 4230_TX, 3812_TX, 3816S_TX, 3816_TX, 5X27_001_TX, 5X27_002_KS_TX, 5X27_002_KSSM_TX, 5X27_003_TX, 5X27_005_TX) SYSL3.
Page 343 AXIS 5570e/AXIS 5670e User’s Manual Section 23: The Parameter List PREMUL4. : 3816_CX (3287_CX, 3268_CX, 3262_CX, 4214_CX, 4224_CX, 4230_CX, 3812_CX, 3816S_CX, 3816_CX, 5224_TX, 5225_TX, 5256_TX, 4214_TX, 4230_TX, 3812_TX, 3816S_TX, 3816_TX, 5X27_001_TX, 5X27_002_KS_TX, 5X27_002_KSSM_TX, 5X27_003_TX, 5X27_005_TX) SYSL4. : 37 (37, 256, 260, 273, 274, 275, 277, 278, 280, 281, 282, 284, 285, 286, 287, 288,...
Page 344 Section 23: The Parameter List AXIS 5570e/AXIS 5670e User’s Manual SYSL5. : 37 (37, 256, 260, 273, 274, 275, 277, 278, 280, 281, 282, 284, 285, 286, 287, 288, 289, 290, 293, 297, 340, 361, 500, 833, 836, 838, 870, 871, 892, 893, 1026, 1140, 1141, 1142, 1143, 1144, 1145, 1146, 1147, 1148, 1149, USER) PASSTHR5.
Page 345 AXIS 5570e/AXIS 5670e User’s Manual Section 23: The Parameter List MPP6. : 132, ENA LPI6. : 6 (3, 4, 6, 8) CPI6. : 10 (5, 10, 12, 13.3, 15, 17, 18) DCPI6. : 5.0 (5.0, 6.0, 6.7, 7.5, 9.0) AUTORI6.
Page 346 Section 23: The Parameter List AXIS 5570e/AXIS 5670e User’s Manual AUTORI7. : YES LM7. : 0, 0, 48 TM7. : 26, 26, 74 LDSF7. : 100, 100, 70 DEFBIN7. : BIN1 (BIN1, BIN2, BIN3, BIN4, BIN5, BIN6, MANUAL, ENVELOPE, CONTINUOUS) PRDRIVER7.
Page 347 AXIS 5570e/AXIS 5670e User’s Manual Section 23: The Parameter List DEFBIN8. : BIN1 (BIN1, BIN2, BIN3, BIN4, BIN5, BIN6, MANUAL, ENVELOPE, CONTINUOUS) PRDRIVER8. : PCL5 (USER, GENERIC, PCL4, PCL5, IBM_PRO, EPSON_FX, EPSON_FX_15CPI, EPSON_LQ, EPSON_LQ_1600K, EPSON_LQ_KS) --- IBM SCS PAGE FORMAT PCORI.
Page 348 Section 23: The Parameter List AXIS 5570e/AXIS 5670e User’s Manual SUPFFBLANK. : NO --- IBM 3270 OPTIONS CASE. : DUAL (DUAL, MONO) BASCOL. : BLACK, ENA XSTRN. AUTNL. ADDNL. FFWPB. FFEOPB. NULSUP. FFCPOS. AFEOPB. --- IBM SCS EXTENDED EMULATION XEMUL.
Page 349 AXIS 5570e/AXIS 5670e User’s Manual Section 23: The Parameter List -------- --- MSTR -------- --- IBM PRINTER DRIVER PRDRIVERBASE. : PCL5 (GENERIC, PCL4, PCL5, IBM_PRO, EPSON_FX, EPSON_FX_15CPI, EPSON_LQ, EPSON_LQ_1600K, EPSON_LQ_KS) SOJS. : 1B 45 1B 26 6C 30 4C EOJS.
Page 350 Section 23: The Parameter List AXIS 5570e/AXIS 5670e User’s Manual LAC. : HP_PCL (DISABLE, HP_PCL, EPSON_LQ) GRD. : HP_PCL (DISABLE, HP_PCL, EPSON_LQ) JOGS. : 1B 26 6C 31 54 SSUS. SBSET. : PC850 (ECMA94, LATIN9, PC437, PC850, PC852, PC857, PC858, PC874, PC891,...
Page 351 AXIS 5570e/AXIS 5670e User’s Manual Section 23: The Parameter List FONT. : 85, 98, DEFAULT,FIXED, 120, 0, UPRIGHT,MEDIUM,4099, FONT. : 86, 98, DEFAULT,FIXED, 120, 0, UPRIGHT,MEDIUM,4099, FONT. : 87, 98, DEFAULT,FIXED, 130, 0, UPRIGHT,MEDIUM,4102, FONT. : 91, 98, DEFAULT,FIXED, 120, 0, ITALIC,MEDIUM,4099, FONT.
Page 352 Section 23: The Parameter List AXIS 5570e/AXIS 5670e User’s Manual FONT. : 1051, 100, DEFAULT,PROP, 0, 100, UPRIGHT,MEDIUM,4101, FONT. : 1053, 100, DEFAULT,PROP, 0, 100, UPRIGHT,BOLD, 4101, FONT. : 1056, 100, DEFAULT,PROP, 0, 100, ITALIC,MEDIUM,4101, FONT. : 1351, 100, DEFAULT,PROP, 0, 120, UPRIGHT,MEDIUM,4101, FONT.
Page 353 AXIS 5570e/AXIS 5670e User’s Manual Section 23: The Parameter List FONT. : 3862, 100, DEFAULT,PROP, 0, 0, UPRIGHT,BOLD, 4197, FONT. : 3863, 100, DEFAULT,PROP, 0, 0, ITALIC,MEDIUM,4197, FONT. : 3864, 100, DEFAULT,PROP, 0, 0, ITALIC,BOLD, 4197, FONT. : 3865, 100, DEFAULT,PROP, 0, 0, UPRIGHT,MEDIUM,4297, FONT.
Page 354 Section 23: The Parameter List AXIS 5570e/AXIS 5670e User’s Manual FONT. : 33601,100, DEFAULT,PROP, 0, 0, UPRIGHT,BOLD, 16602, FONT. : 33719,100, DEFAULT,PROP, 0, 0, ITALIC,MEDIUM,16602, FONT. : 33729,100, DEFAULT,PROP, 0, 0, ITALIC,BOLD, 16602, FONT. : 34103,100, DEFAULT,PROP, 0, 0, UPRIGHT,MEDIUM,4148, FONT.
Page 355 AXIS 5570e/AXIS 5670e User’s Manual Section 23: The Parameter List FONT. : 50011,100, PC942,PROP, 0, 67, UPRIGHT,MEDIUM,28752, 1B 28 31 39 4B 1B 26 74 33 31 50 FONT. : 50012,100, PC942,PROP, 0, 67, UPRIGHT,MEDIUM,28752, 1B 28 31 39 4B 1B 26 74 33 31 50 FONT.
Page 356 Section 23: The Parameter List AXIS 5570e/AXIS 5670e User’s Manual 28 31 39 48 1B 26 74 33 38 50 FONT. : 50034,100, PC891,PROP, 0, 96, UPRIGHT,MEDIUM,43088, 1B 28 31 39 48 1B 26 74 33 38 50 FONT. : 50035,100, PC891,PROP, 0, 96, UPRIGHT,MEDIUM,43088, 1B 28 31 39 48 1B 26 74 33 38 50 FONT.
Page 357 AXIS 5570e/AXIS 5670e User’s Manual Section 23: The Parameter List FONT. : 50050,100, PC891,PROP, 0, 84, UPRIGHT,MEDIUM,41040, 1B 28 31 39 48 1B 26 74 33 38 50 FONT. : 50051,100, PC891,PROP, 0, 76, UPRIGHT,MEDIUM,41040, 1B 28 31 39 48 1B 26 74 33 38 50 FONT.
Page 358 Section 23: The Parameter List AXIS 5570e/AXIS 5670e User’s Manual 28 31 38 43 1B 26 74 33 38 50 FONT. : 50101,100, PC903,PROP, 0, 144, UPRIGHT,MEDIUM,37058, 1B 28 31 38 43 1B 26 74 33 38 50 FONT. : 50102,100, PC903,PROP, 0, 120, UPRIGHT,MEDIUM,37058, 1B 28 31 38 43 1B 26 74 33 38 50 FONT.
Page 359 AXIS 5570e/AXIS 5670e User’s Manual Section 23: The Parameter List FONT. : 50117,100, PC903,PROP, 0, 96, UPRIGHT,MEDIUM,37058, 1B 28 31 38 43 1B 26 74 33 38 50 FONT. : 50118,100, PC903,PROP, 0, 80, UPRIGHT,MEDIUM,37058, 1B 28 31 38 43 1B 26 74 33 38 50 FONT.
Page 360 Section 23: The Parameter List AXIS 5570e/AXIS 5670e User’s Manual 28 31 38 48 1B 26 74 33 38 50 FONT. : 50140,100, PC891,PROP, 0, 76, UPRIGHT,MEDIUM,43088, 1B 28 31 38 48 1B 26 74 33 38 50 FONT. : 50141,100, PC891,PROP, 0, 67, UPRIGHT,MEDIUM,43088, 1B 28 31 38 48 1B 26 74 33 38 50 FONT.
Page 361 AXIS 5570e/AXIS 5670e User’s Manual Section 23: The Parameter List PAPER_JAM_ADDRESS. : OUT_OF_PAPER_ADDRESS. : TONER_LOW_ADDRESS. : NO_TONER_ADDRESS. : PRINTER_OFFLINE_ADDRESS. :...
Page 362: Glossary
Section 24: Glossary AXIS 5570e/AXIS 5670e User’s Manual Section 24 Glossary Active Directory Active Directory - a structure supported by Windows 2000 that lets any object on a network be tracked and located. Active Directory is the directory service used in Windows 2000 Server and provides the foundation for Windows 2000 distributed networks.
Page 363 This is a file that resides in the print server’s memory and contains all the parameters that determine the AXIS 5570e/AXIS 5670e functionality. By editing the config file (changing the parameter settings), you can configure the AXIS 5570e/AXIS 5670e to meet the printing needs of your network. CPGID...
Page 364 Section 24: Glossary AXIS 5570e/AXIS 5670e User’s Manual Flash Memory The print server software is stored in Flash Memory. This memory is provided by a silicon chip that like any other ROM device, retains data content even after power is removed. However, Flash Memory is unique because it allows its data to be erased and re-written.
Page 365 AXIS 5570e/AXIS 5670e User’s Manual Section 24: Glossary Logical Printer A logical printer acts as a filter between the network and the physical printer. It appears to the user as a normal printer with additional characteristics. For example a UNIX workstation may only send a line feed (LF) to a shared printer that needs carriage return (CR) and LF.
Page 366 Section 24: Glossary AXIS 5570e/AXIS 5670e User’s Manual NCP(2) Network Control Program. SNA program resident in the FEP. NCP off- loads certain line protocol and routing functions from the host CPU. NetWare Directory Services. A hierarchical data base that manages NetWare network resources such as servers and volumes.
Page 367 AXIS 5570e/AXIS 5670e User’s Manual Section 24: Glossary SNA Character String. A sequence of control commands that allows sophisticated control of printers and other devices. Systems Network Architecture. IBM's data communications architecture defining levels of protocols for communications between terminals and applications as well as between programs. Originally SNA was strictly host-based with VTAM controlling the network except for path control which was provided by NCP in the FEP.
Page 368 Section 24: Glossary AXIS 5570e/AXIS 5670e User’s Manual Uniform Resource Locator. A way of specifying the location of publicly available information on the Internet. VPDI Virtual Printer Driver Interface VTAM Virtual Telecommunications Access Method. Mainframe software that performs network control and management. VTAM's most important objective is to provide the SSCP services.
Page 369 AXIS 5570e/AXIS 5670e User’s Manual Index Numerics 3270DS 194, 195 Account file Active Directory Admin APPC AppleTalk Approvals AS/400 ASCII ASCII to Postscript Conversion Autodetect Auto-Detect Printer Type 25, 206 AutoIP AutoIP address structure Axinstall AXIS IPP Gateway Configuration AXIS LPR Gateway Configuration...
Page 370 AXIS 5570e/AXIS 5670e User’s Manual Certificates Delete Import View Character Set Conversion Checking SSL/TLS Status Color Concentrator gateway, general Concentrator gateway, Microsoft Concentrator gateway, NetWare 180, 295, 363 config file Configuration and Management Configuration methods 156, 201 NetWare Administrator 156, 201...
Page 371 AXIS 5570e/AXIS 5670e User’s Manual Hex Dump Mode Print Problems Default Input Bin Delete Certificate Device Features DEVICE Statement DHCP Enabled parameter Digital Copier printing Digital Copier Support Dimensions Disabling Protocols DSPU Duplex Dynamic IP address Assignment EBCDIC Enable/disable SNMP...
Page 372 AXIS 5570e/AXIS 5670e User’s Manual Selection Typographical Width Front Panel FSS Statement FSSDEF Statement 192, 364 FTP_ENB Hardware Hardware Inventory Hex Dump Mode Hex Transparancy Host Name HTML HTTP HTTPS IBM Capabilities IBM Font Selection IBM SNA Importing a Certificate...
Page 373 AXIS 5570e/AXIS 5670e User’s Manual Client Printing Requirements iPrint Last Code Point Local Printer Logical Printer 220, 291 Logical Printers Logon-mode Entry 177, 365 LU6.2 Macintosh Choosing a Printer Installing the Print Server Microsoft SNA Mounting the AXIS 5570e NCP(2)
Page 374 AXIS 5570e/AXIS 5670e User’s Manual Remote Printer Mode NetWare SAA Network Indicator Printer Speed Network Connection Network Connector Network Group Create Network Indicator Paper Size Physical 187, 295 Parameter List Pass-through gateway password Point size Ports Power Indicator Power Consumption...
Page 375 AXIS 5570e/AXIS 5670e User’s Manual Test page Protocols Disable Enable Protocols and Datastreams PRTnnnn Statement PU2.1 Pure IP Queue-based printing Redirecting Print Jobs Restart RISC SAP(2) SBCS SDLC Secure Management Secure Web Services Security Security Settings Setting the Internet address...
Page 376 AXIS 5570e/AXIS 5670e User’s Manual SNA Printing 3174 CU Mode 36, 60 5494 CU Mode Snap-in for iPrint 199, 367 SNMP SSCP SSL/TLS Status Starting AXIS ThinWizard 194, 197 Status file String Functions 223, 251 String Substitutions Substitutions 18, 290...
Page 377 AXIS 5570e/AXIS 5670e User’s Manual PROS A PROS B Reverse Telnet Upgrading 181, 182 User User Defined Strings View Certificate VTAM VTAM Logon-mode entry Web Flash Loading 32, 33 WINS Wizard World Wide Web...

This manual is also suitable for:

5670e

Axis 5570e User Manual

Quick Links

AXIS 5570e

AXIS 5670e

Related Manuals for Axis 5570e

Summary of Contents for Axis 5570e

This manual is also suitable for:

Table of Contents