Table Of Contents - IBM HC10 - BladeCenter - 7996 Service Manual

Contents
Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . vii
Guidelines for trained service technicians . . . . . . . . . . . . . . . viii
Safety statements . . . . . . . . . . . . . . . . . . . . . . . . ix
Chapter 1. Introduction . . . . . . . . . . . . . . . . . . . . . . 1
Related documentation . . . . . . . . . . . . . . . . . . . . . . 1
Notices and statements in this document . . . . . . . . . . . . . . . . 2
Features and specifications . . . . . . . . . . . . . . . . . . . . . 3
Blade workstation controls and LEDs . . . . . . . . . . . . . . . . . 4
Turning on the blade workstation . . . . . . . . . . . . . . . . . . . 6
Turning off the blade workstation . . . . . . . . . . . . . . . . . . . 6
System board layouts . . . . . . . . . . . . . . . . . . . . . . . 7
Chapter 2. Configuration information and instructions . . . . . . . . . 9
Firmware updates . . . . . . . . . . . . . . . . . . . . . . . . 9
Using the Configuration/Setup Utility program . . . . . . . . . . . . . . 9
Configuring the Gigabit Ethernet controllers . . . . . . . . . . . . . . . 9
Blade workstation Ethernet controller enumeration . . . . . . . . . . . . 10
Chapter 3. Parts listing, Type 7996 . . . . . . . . . . . . . . . . . 11
Chapter 4. Removing and replacing blade workstation components . . . . 13
Installation guidelines . . . . . . . . . . . . . . . . . . . . . . 13
Removing the blade workstation from a BladeCenter unit . . . . . . . . . 16
Installing the blade workstation in a BladeCenter unit . . . . . . . . . . . 17
Removing and replacing Tier 1 CRUs
Removing and replacing FRUs . . . . . . . . . . . . . . . . . . . 32
© Copyright IBM Corp. 2007
Inspecting for unsafe conditions
Guidelines for servicing electrical equipment . . . . . . . . . . . . . viii
System board connectors . . . . . . . . . . . . . . . . . . . . 7
System board jumpers and buttons . . . . . . . . . . . . . . . . . 7
System reliability guidelines . . . . . . . . . . . . . . . . . . . 15
Handling static-sensitive devices . . . . . . . . . . . . . . . . . 15
Returning a device or component . . . . . . . . . . . . . . . . . 15
Removing the blade workstation cover . . . . . . . . . . . . . . . 19
Installing the blade workstation cover . . . . . . . . . . . . . . . . 20
Removing the bezel assembly . . . . . . . . . . . . . . . . . . 21
Installing the bezel assembly . . . . . . . . . . . . . . . . . . . 21
Removing a SATA storage drive
Installing a SATA storage drive . . . . . . . . . . . . . . . . . . 23
Removing a memory module . . . . . . . . . . . . . . . . . . . 24
Installing a memory module . . . . . . . . . . . . . . . . . . . 24
Removing a compression card . . . . . . . . . . . . . . . . . . 26
Installing a compression card
Removing a graphics card . . . . . . . . . . . . . . . . . . . . 28
Installing a graphics card . . . . . . . . . . . . . . . . . . . . 29
Removing the battery . . . . . . . . . . . . . . . . . . . . . 30
Installing the battery . . . . . . . . . . . . . . . . . . . . . . 30
Removing a microprocessor and heat sink . . . . . . . . . . . . . . 32
Installing a microprocessor and heat sink . . . . . . . . . . . . . . 34
Removing the system board assembly . . . . . . . . . . . . . . . 36
Installing the system board assembly . . . . . . . . . . . . . . . . 37
. . . . . . . . . . . . . . . . . viii
. . . . . . . . . . . . . . . . 19
. . . . . . . . . . . . . . . . . 22
. . . . . . . . . . . . . . . . . . 27
iii