Page 4
IBM may make improvements or changes in the products or the programs described in this publication at any time. Requests for technical information about IBM products should be made to your IBM Authorized Dealer or your IBM Marketing Representative.
Chapter 1. About this manual This manual contains service and reference information for IBM 8301, 8302, 8303, 8304, 8305, 8306, 8307, 8308, 8309, 8310, 8311, 8312, 8313, 8314, and 8315. This manual is divided into product service sections and a related service section,...
Page 8
Leia todas as instruções de cuidado e perigo antes de executar qualquer operação. Lea atentamente todas las declaraciones de precaución y peligro ante de llevar a cabo cualquier operación. Hardware Maintenance Manual...
Notes: v Types 8301, 8302, 8303, 8304, 8305, 8306, 8307, 8308, 8309, 8310, 8311, 8312, 8313, 8314, and 8315 computers default to come up quiet (no beep and no memory count and checkpoint code display) when no errors are detected by POST.
Page 10
DID YOU RECEIVE THE CORRECT RESPONSE? If NO, continue to 002 . If YES, proceed to 003 . If the Power Management feature is enabled, do the following: 1. Start the Configuration/Setup Utility program (see “Setup Utility program” on page 24) 2.
When adding an option, use these instructions along with the instructions that come with the option. Go to Access IBM for general information about the use, operation, and maintenance of your computer. Access IBM also contains information to help solve problems and get repair service or other technical assistance.
Page 12
Remote Program Load (RPL) and Dynamic Host Configuration Protocol (DHCP) v Wake on LAN v Wake on Ring (in the IBM Setup Utility program, this feature is called Serial Port Ring Detect for an external modem and Modem Ring Detect for an internal...
1. The operating systems listed here are being tested for compatibility at the time this publication goes to press. Additional operating systems might be identified by IBM as compatible with your computer following the publication of this booklet. Corrections and additions to this list are subject to change. To determine if an operating system has been tested for compatibility, check the Web site of the operating system vendor.
Page 14
Remote Program Load (RPL) and Dynamic Host Configuration Protocol (DHCP) v Wake on LAN v Wake on Ring (in the IBM Setup Utility program, this feature is called Serial Port Ring Detect for an external modem and Modem Ring Detect for an internal...
2. The operating systems listed here are being tested for compatibility at the time this publication goes to press. Additional operating systems might be identified by IBM as compatible with your computer following the publication of this booklet. Corrections and additions to this list are subject to change. To determine if an operating system has been tested for compatibility, check the Web site of the operating system vendor.
Page 16
Remote Program Load (RPL) and Dynamic Host Configuration Protocol (DHCP) v Wake on LAN v Wake on Ring (in the IBM Setup Utility program, this feature is called Serial Port Ring Detect for an external modem and Modem Ring Detect for an internal...
3. The operating systems listed here are being tested for compatibility at the time this publication goes to press. Additional operating systems might be identified by IBM as compatible with your computer following the publication of this booklet. Corrections and additions to this list are subject to change. To determine if an operating system has been tested for compatibility, check the Web site of the operating system vendor.
Page 18
Remote Program Load (RPL) and Dynamic Host Configuration Protocol (DHCP) v Wake on LAN v Wake on Ring (in the IBM Setup Utility program, this feature is called Serial Port Ring Detect for an external modem and Modem Ring Detect for an internal...
4. The operating systems listed here are being tested for compatibility at the time this publication goes to press. Additional operating systems might be identified by IBM as compatible with your computer following the publication of this booklet. Corrections and additions to this list are subject to change. To determine if an operating system has been tested for compatibility, check the Web site of the operating system vendor.
Dimensions Height: 110 mm (4.3 in.) Width: 310 mm (12.2 in.) Depth: 343 mm (13.5 in.) Weight Minimum configuration as shipped: 8.1 kg (18 lb) Maximum configuration: 9.1 kg (20 lb) Environment Air temperature: System on: 10° to 35°C (50° to 95° F) System off: 10°...
Page 21
Dimensions Height: 104 mm (4.1 in.) Width: 360 mm (14.2 in.) Depth: 412 mm (16.2 in.) Weight Minimum configuration as shipped: 8.1 kg (18 lb) Maximum configuration: 9.1 kg (20 lb) Environment Air temperature: System on: 10° to 35°C (50° to 95° F) System off: 10°...
Types 8305, 8306, 8309, and 8313 This section lists the physical specifications for your computer. Dimensions Height: 140 mm (5.5 in.) Width: 425 mm (16.7 in.) Depth: 414 mm (16.3 in) Weight Minimum configuration as shipped: 10.0 kg (22 lb) Maximum configuration: 11.4 kg (25.0 lb) Environment Air temperature:...
Types 8307, 8308, 8310, 8311, 8314, and 8315 This section lists the physical specifications for your computer. Dimensions Height: 413 mm (16.25 in.) Width: 191 mm (7.5 in.) Depth: 406 mm (16 in.) Weight Minimum configuration as shipped: 9.1 kg (20 lb) Maximum configuration: 10.2 kg (22.5 lb) Environment Air temperature:...
Within the United States, call 1-800-IBM-2YOU (1-800-426-2968), your IBM reseller, or IBM marketing representative. v Within Canada, call 1-800-565-3344 or 1-800-IBM-4YOU. v Outside the United States and Canada, contact your IBM reseller or IBM marketing representative. Hardware Maintenance Manual...
Within the United States, call 1-800-IBM-2YOU (1-800-426-2968), your IBM reseller, or IBM marketing representative. v Within Canada, call 1-800-565-3344 or 1-800-IBM-4YOU. v Outside the United States and Canada, contact your IBM reseller or IBM marketing representative. Chapter 3. General information...
Within the United States, call 1-800-IBM-2YOU (1-800-426-2968), your IBM reseller, or IBM marketing representative. v Within Canada, call 1-800-565-3344 or 1-800-IBM-4YOU. v Outside the United States and Canada, contact your IBM reseller or IBM marketing representative. Hardware Maintenance Manual...
Within the United States, call 1-800-IBM-2YOU (1-800-426-2968), your IBM reseller, or IBM marketing representative. v Within Canada, call 1-800-565-3344 or 1-800-IBM-4YOU. v Outside the United States and Canada, contact your IBM reseller or IBM marketing representative. Chapter 3. General information...
Setup Utility program Attention: A customized setup configuration (other than default settings) might exist on the computer you are servicing. Running the Setup Utility program might alter those settings. Note the current configuration settings and verify that the settings are in place when service is complete.
Product Recovery Program menu Type 8301, 8302, 8303, 8304, 8305, 8306, 8307, 8308, 8309, 8310, 8311, 8312, 8314, and 8315 machines have recovery and diagnostics programs on a separate hard drive partition. The Enhanced Diagnostics diskette is not shipped with the machine. To download the Diagnostics program, see “Diagnostics program download”...
Diagnostics program download To download the Diagnostics program, do the following: v Go to http://www.ibm.com/. v Select Support. v Select Personal computing from the ″Get product support for″ pull-down menu. v Search for the machine type in the ″Quick Path″ box on the left.
ChkDigits: Contains a 2-digit check-digit value to ensure the following: – Diagnostics were run on the specified date. – Diagnostics were run on the specified IBM computer. – The diagnostic error code is recorded correctly. v Text: Description of the error.
Page 34
– Random Seek – Min-Max Seek – Butterfly Seek v Verify Tests: - checks the integrity of the data present on the media. – Linear Verify – Random Verify v Surface Scan Tests: - checks the drive media for defects. –...
non-destructive ranges somehow overlap, then the overlapped area is considered non-destructive. For example, if users specify both destructive and non-destructive ranges as the same, then the entire drive is tested as non-destructive. Quick and Full erase - hard drive The Diagnostics program offers two hard drive format utilities: v Quick Erase Hard Drive v Full Erase Hard Drive The Quick Erase Hard Drive provides a DOS utility that performs the following...
The Full Erase Hard Drive provides a DOS utility that performs the following steps. v Performs all the steps in Quick Erase. v Provides a DOS utility that writes random data to all sectors of the hard drive. v Provide an estimate of time to completion along with a visual representation of completion status.
Important: Before you install or remove any option, read “Safety information” on page 271. These precautions and guidelines will help you work safely. Locating connectors on the front Types 8301 and 8302 The following illustration shows the locations of the connectors on the front of the computer.
Page 38
1 USB connector 2 USB connector Types 8305, 8306, 8309, and 8313 The following illustration shows the locations of the connectors on the front of the computer. 1 USB connector 2 USB connector Types 8307, 8308, 8310, 8311, 8314, and 8315 The following illustration shows the locations of the connectors on the front of the computer.
Locating the connectors on the rear Types 8301 and 8302 The following illustration shows the locations of the connectors on the rear of the computer. 1 Serial connector 2 Mouse connector 3 Parallel connector 4 Ethernet connector 5 Audio line in connector...
Page 40
Connector Serial connector Mouse connector Parallel connector Ethernet connector Audio line in connector Audio line out connector Microphone connector USB connectors Keyboard connector Hardware Maintenance Manual Description Used to attach an external modem, serial printer, or other devices that use a 9-pin serial connector. Used to attach a mouse, trackball, or other pointing device that uses a standard mouse connector.
Page 41
Types 8303, 8304, and 8312 The following illustration shows the locations of the connectors on the rear of the computer. 1 Serial connector 2 Mouse connector 3 Parallel connector 4 Ethernet connector 5 Audio line in connector 6 Power connector 7 PCI slots 8 AGP slot (some models) Note: Some connectors on the rear of the computer are color-coded to help you to...
Page 42
Connector Serial connector Mouse connector Parallel connector Ethernet connector Audio line in connector Audio line out connector Microphone connector USB connectors Keyboard connector Hardware Maintenance Manual Description Used to attach an external modem, serial printer, or other devices that use a 9-pin serial connector. Used to attach a mouse, trackball, or other pointing device that uses a standard mouse connector.
Page 43
Types 8305, 8306, 8309, and 8313 The following illustration shows the locations of the connectors on the rear of the computer. 1 Power connector 2 Mouse connector 3 Serial connector 4 Parallel connector 5 Ethernet connector 6 Audio line in connector 7 PCI slots 8 AGP slot (some models) Note: Some connectors on the rear of the computer are color-coded to help you to...
Page 44
1 Serial connector 2 Mouse connector 3 Keyboard connector 4 USB connectors 5 Serial connector 6 Parallel connector 7 VGA monitor connector 8 USB connectors Note: Some connectors on the rear of the computer are color-coded to help you to determine where to connect the cables on your computer.
Audio line in connector Obtaining device drivers Device drivers can be obtained for operating systems that are not preinstalled at http://www.ibm.com/pc/support/ on the World Wide Web. Installation instructions are provided in README files with the device driver files. Installing internal options The capabilities of the computer can be expanded by adding memory, drives, or adapters.
Removing the cover Types 8303, 8304, and 8312 Important: Read “Safety information” on page 271 and “Handling electrostatic discharge-sensitive devices” on page 274 before you begin. To remove the cover: 1. Shut down your operating system, remove any media (diskettes, CDs, or tapes) from the drives, and turn off all attached devices and the computer.
Page 47
4. Press the buttons on the sides of the computer and pivot the rear end of the cover up toward the front of the computer. Types 8307, 8308, 8310, 8311, 8314, and 8315 Important: Read “Safety information” on page 271 and “Handling electrostatic discharge-sensitive devices”...
Locating components Types 8303, 8304, and 8312 The following illustration will help you locate the various components in your computer. 1 Power supply 2 PCI slot 3 AGP slot (some models) 4 Support bar Hardware Maintenance Manual 5 DIMM 6 Hard disk drive 7 CD-ROM drive or DVD-ROM drive 8 Diskette drive...
Page 49
Types 8305, 8306, 8309, and 8313 The following illustration will help you locate the various components in your computer. 1 CD drive or DVD drive 2 USB connector 3 USB connector 4 Hard disk drive 5 Diskette drive 6 DIMMs 7 System Board 8 Microprocessor and heat sink 9 PCI slots...
The system board (sometimes called the planar or motherboard) is the main circuit board in your computer. It provides basic computer functions and supports a variety of devices that are IBM-installed or that you can install later. Hardware Maintenance Manual...
Page 51
The system board (sometimes called the planar or motherboard) is the main circuit board in your computer. It provides basic computer functions and supports a variety of devices that are IBM-installed or that you can install later. 9 Battery 10 Clear CMOS/Recovery jumper...
Page 52
The system board (sometimes called the planar or motherboard) is the main circuit board in your computer. It provides basic computer functions and supports a variety of devices that are IBM-installed or that you can install later. Hardware Maintenance Manual...
The following illustration shows the locations of parts on the system board. 1 Microprocessor 2 DIMM connector 1 3 DIMM connector 2 4 Power connector 5 Diskette drive connector 6 Primary IDE connector 7 Front panel connector 8 Secondary IDE connector Installing memory Your computer has two connectors for installing dual inline memory modules (DIMMs) that provide up to a maximum of 2.0 GB of system memory.
3. Open the retaining clips. 4. Make sure the notches in the DIMM align with the tabs on the connector. Push or insert the DIMM straight down into the connector until the retaining clips close. What to do next: v To work with another option, go to the appropriate section. v To complete the installation, go to “Replacing the cover and connecting the cables”...
Page 55
2. Pivot one of the drive bay latch handles toward the front of the computer and then pivot the drive bay cage upward, as shown, until it is latched in the up position. Repeat this procedure for the remaining drive bay. 3.
Page 56
7. Install the adapter-slot-cover latch. 8. Clear any cables that might impede the replacement of the drive bays. 9. Replace the support bar and pivot the two drive bays back to their original positions. What to do next: v To work with another option, go to the appropriate section. v To complete the installation, go to “Replacing the cover and connecting the cables”...
Page 57
5. Install the adapter-slot-cover latch. What to do next: v To work with another option, go to the appropriate section. v To complete the installation, go to “Types 8305, 8306, 8309, and 8313” on page 68. Installing adapters in Types 8307, 8308, 8310, 8311, 8314, and 8315 This section provides information and instructions for installing and removing adapters.
To complete the installation, go to “Types 8307, 8308, 8310, 8311, 8314, and 8315” on page 68. Installing internal drives Types 8301 and 8302 To remove the hard disk drive, do the following: 1. Push up on the blue bar on the front of the computer. This will detach the hard drive.
Page 59
Also, it is important to correctly connect the internal drive cables to the installed drive. Drive specifications: Your computer might come with the following IBM-installed drives: v A 3.5-inch diskette drive in bay 1 v A CD-ROM drive or DVD-ROM drive in bay 2 (some models) v A 3.5-inch hard disk drive in bay 3...
Page 60
3. Remove the metal shield from the drive bay by inserting a flat-blade screwdriver into one of the slots and gently prying it loose. 4. Make sure the drive is set correctly as the master device. Refer to the documentation that comes with your CD-ROM drive or DVD-ROM drive for master/slave jumper information.
Page 61
d. Your computer has extra power connectors for connecting additional drives. Connect the power cable to the drive. 8. Clear any cables that might impede replacement of the drive cage. 9. Pivot the drive cage back into place. What to do next: v To work with another option, go to the appropriate section.
Page 62
Also, it is important to correctly connect the internal drive cables to the installed drive. Drive specifications: Your computer comes with the following IBM-installed drives: v A CD drive or DVD drive in bay 1 (some models) v A 3.5-inch hard disk drive in bay 3...
Page 63
The following illustration shows the locations of the drive bays. The following list describes some of the drives that you can install in each bay and their height requirements: 1 Bay 1 - Maximum height: 43.0 mm (1.7 in.) 2 Bay 2 - Maximum height: 43.0 mm (1.7 in.) 3 Bay 3 - Maximum height: 25.8 mm (1.0 in.) 4 Bay 4 - Maximum height: 25.8 mm (1.0 in.) Notes:...
Page 64
position. 6. Make sure the drive that you are installing is set correctly as either a master or a slave device. v If it is a hard disk drive, set it as a slave device. v If it is the first CD drive or DVD drive, set it as a master device. v If it is an additional CD drive or DVD drive, set it as a slave device.
Page 65
Connecting the first IDE CD drive or DVD drive: 1. Locate the three-connector signal cable that comes with your computer or with the new drive. 2. Locate the secondary IDE connector on the system board. See “Types 8305, 8306, 8309, and 8313” on page 45. 3.
Page 66
Also, it is important to correctly connect the internal drive cables to the installed drive. Drive specifications: Your computer comes with the following IBM-installed drives: v A CD drive or DVD drive in bay 1 (some models) v A 3.5-inch diskette disk drive in bay 4...
Page 67
The following illustration shows the locations of the drive bays. The following list describes some of the drives you can install in each bay and their height requirements: 1 Bay 1 - Maximum height: 43.0 mm (1.7 in.) 2 Bay 2 - Maximum height: 43.0 mm (1.7 in.) 3 Bay 3 - Maximum height: 25.8 mm (1.0 in.) 4 Bay 4 - Maximum height: 25.8 mm (1.0 in.) 5 Bay 5 - Maximum height: 25.8 mm (1.0 in.)
Page 68
4. Remove the metal shield from the drive bay by inserting a flat-blade screwdriver into one of the slots and gently prying it loose. 5. Make sure the drive that you are installing is set correctly as either a master or a slave device.
Page 69
to the system board. For a CD-ROM drive, you might also have an audio cable. The steps to connect an IDE drive are different depending on the type of drive you are connecting. Use one of the following procedures for your drive connection. Connecting the first IDE CD drive or DVD drive: 1.
After you add the security cable, make sure that it does not interfere with other cables that are connected to the computer. For more information about security, see Installing a cable lock in Access IBM. To install a rope clip: 1.
Page 71
For more information about security, see Installing a cable lock in Access IBM. To install a rope clip: 1. Remove the cover. See “Types 8305, 8306, 8309, and 8313” on page 40.
Page 72
1. Remove cover (see “Types 8307, 8308, 8310, 8311, 8314, and 8315” on page 41). 2. Use a tool, such as a screwdriver, to remove the two metal knockouts. 3. Insert the rope clip through the rear panel; then attach and tighten the nuts with an appropriately sized or adjustable wrench.
9. Turn on the computer and all attached devices. 10. Use the IBM Setup Utility program to set the date and time and any passwords. See “Setup Utility program” on page 24. Replacing the cover and connecting the cables...
Page 74
Also, depending on the option that is installed, you might need to confirm the updated information in the IBM Setup Utility program. To replace the cover and connect cables to your computer: 1.
Page 75
IBM Setup Utility program. To replace the cover and connect cables to your computer: 1. Ensure that all components have been reassembled correctly and that no tools or loose screws are left inside your computer.
4. Remove the 2 front and 2 back screws holding the cover in place. 5. Slide the top cover toward the front of the box and lift off. Removing the CD-ROM drive Types 8301 and 8302 To remove the CD-ROM drive from these machine types, do the following:...
1. Turn off the computer and peripheral devices and disconnect all external cables and power cords; then, remove the cover. See “Removing the cover Types 8301 and 8302” on page 71. 2. Remove the 2 screws holding the CD cage in place and pull the cage out.
6. Pull out and lift up the processor socket lever arm upward to its maximum vertical position to release the processor. 7. Lift the processor out of the system board. Notes: a. When installing the new processor, make sure to reinstall the fansink to insure proper cooling.
3. Pivot the drive bay latch handle toward the front of the computer and pivot the drive bay cage upward, as shown, until it is latched in the up position. 4. Install the drive into the bay. Align the screw holes and insert the two screws. 5.
Page 81
4. Remove the metal shield from the drive bay by inserting a flat–blade screwdriver into one of the slots and gently pry it loose. 5. Pivot the drive bay latch handle toward the front of the computer and pivot the drive bay cage toward the front of the computer until the drive cage latch catches to the chassis.
Page 82
7. Install the drive into the bay. Align the screw holes and insert the two screws. 8. Pivot the drive bay cage back into place. 9. Each integrated drive electronics (IDE) drive requires two cables; a four-wire power cable that connects to the power supply and a signal cable that connects to the system board.
1. Turn off the server and peripheral devices and disconnect all external cables and power cords; then, remove the cover. See “Removing the cover Types 8301 and 8302” on page 71. 2. Remove the black plastic spacer from the front left corner of the box.
5. Remove the hard disk drive guide from the top of the power source. 6. Remove the screw holding the rear portion of the power supply. 7. Slide the main portion of the power supply to the left and lift it out. Lift the rear portion of the power supply out.
2. Disconnect all wires that the power supply is attached to. 3. Remove the two screws that hold the power supply in place. 4. Lift the power supply out. Types 8305, 8306, 8309, and 8313 1. Remove the cover. See “Types 8305, 8306, 8309, and 8313” on page 40. 2.
1. Turn off the server and peripheral devices and disconnect all external cables and power cords; then, remove the cover. See “Removing the cover Types 8301 and 8302” on page 71. 2. Remove the CD drive cage. See “Removing the CD-ROM drive Types 8301 and 8302”...
6. Slide the system board toward the front of the machine and lift out. Types 8303, 8304, and 8312 To remove the system board, do the following: 1. Turn off the server and peripheral devices and disconnect all external cables and power cords;...
Types 8305, 8306, 8309, and 8313 Notes: The BIOS and Vital Product Data (VPD) for the computer you are servicing must be installed on the new system board (FRU) after it is installed in the computer. To do this, you must run the Flash Update program using the Flash Update diskette. See “BIOS levels”...
After replacing parts, you need to replace the cover and reconnect cables, including telephone lines and power cords. Also, depending on the option that is installed, you might need to confirm the updated information in the IBM Setup Utility program. To replace the cover and connect cables to the computer: 1.
Page 90
a. Route the hard disk drive power cable through the plastic clip attached to the hard disk drive IDE cable as shown. b. Route the hard disk drive IDE cable around the power plug on the board as shown. c. Route both the hard disk drive IDE cable and the hard disk drive power cable through the plastic clip shown on the back of the power supply.
Page 91
3. Place the lid on the computer and slide toward the rear. 4. Replace the 2 front and 2 back screws which hold the cover in place. 5. Replace the bezel. 6. Reconnect the external cables and power cords to the computer. 7.
Diagnostic error codes Refer to the following diagnostic error codes when using the diagnostic tests. See ″Diagnostics″ on page 23 for the specific type for information about the Diagnostic programs. In the following index, X can represent any number. Diagnostic Error Code 000-000-XXX BIOS Test Passed 000-002-XXX...
Page 96
Diagnostic Error Code 000-197-XXX BIOS test warning 000-198-XXX BIOS test aborted 000-199-XXX BIOS test failed, cause unknown 000-250-XXX BIOS APM failure 000-270-XXX BIOS ACPI failure 001-000-XXX System Test Passed 001-00X-XXX System Error 001-01X-XXX System Error 001-024-XXX System Addressing test failure 001-025-XXX System Checksum Value error 001-026-XXX...
Page 97
Diagnostic Error Code 001-038-XXX System Extension failure 001-039-XXX System DMI data structure error 001-040-XXX System IRQ failure 001-041-XXX System DMA failure 001-195-XXX System Test aborted by user 001-196-XXX System test halt, error threshold exceeded 001-197-XXX System test warning 001-198-XXX System test aborted 001-199-XXX System test failed, cause unknown 001-250-XXX...
Page 98
Diagnostic Error Code 001-271-XXX System IRQ4 failure 001-272-XXX System IRQ5 failure 001-273-XXX System IRQ6 (diskette drive) failure 001-274-XXX System IRQ7 failure 001-275-XXX System IRQ8 failure 001-276-XXX System IRQ9 failure 001-277-XXX System IRQ10 failure 001-278-XXX System IRQ11 failure 001-279-XXX System IRQ12 failure 001-280-XXX System IRQ13 failure 001-281-XXX...
Page 99
Diagnostic Error Code 001-301-XXX System RTC Century byte error 005-000-XXX Video Test Passed 005-00X-XXX Video error 005-010-XXX 005-011-XXX 005-012-XXX 005-013-XXX Video Signal failure 005-016-XXX Video Simple Pattern test failure 005-024-XXX Video Addressing test failure 005-025-XXX Video Checksum Value error 005-027-XXX Video Configuration/Setup error 005-031-XXX Video Device Cable failure...
Page 100
Diagnostic Error Code 005-197-XXX Video test warning 005-198-XXX Video test aborted 005-199-XXX Video test failed, cause unknown 005-2XX-XXX 005-3XX-XXX Video subsystem error 006-000-XXX Diskette interface Test Passed 006-0XX-XXX Diskette interface error 006-195-XXX Diskette interface Test aborted by user 006-196-XXX Diskette interface test halt, error threshold exceeded 006-197-XXX Diskette interface test warning...
Page 101
Diagnostic Error Code 011-000-XXX Serial port Interface Test Passed 011-001-XXX Serial port Presence 011-002-XXX 011-003-XXX Serial port Timeout/Parity error 011-013-XXX 011-014-XXX Serial port Control Signal/Loopback test failure 011-015-XXX Serial port External Loopback failure 011-027-XXX Serial port Configuration/Setup error 011-03X-XXX 011-04X-XXX Serial port failure 011-195-XXX Serial port Test aborted by user...
Page 102
Diagnostic Error Code 014-001-XXX Parallel port Presence 014-002-XXX 014-003-XXX Parallel port Timeout/Parity error 014-013-XXX 014-014-XXX Parallel port Control Signal/Loopback test failure 014-015-XXX Parallel port External Loopback failure 014-027-XXX Parallel port Configuration/Setup error 014-03X-XXX 014-04X-XXX Parallel port failure 014-195-XXX Parallel port Test aborted by user 014-196-XXX Parallel port test halt, error threshold exceeded...
Page 103
Diagnostic Error Code 015-002-XXX USB port Timeout 015-015-XXX USB port External Loopback failure 015-027-XXX USB port Configuration/Setup error 015-032-XXX USB port Device Controller failure 015-034-XXX USB port buffer allocation failure 015-035-XXX USB port Reset condition detected 015-036-XXX USB port Register error 015-040-XXX USB port IRQ failure 015-195-XXX...
Page 104
Diagnostic Error Code 018-195-XXX PCI Card Test aborted by user 018-196-XXX PCI Card test halt, error threshold exceeded 018-197-XXX PCI Card test warning 018-198-XXX PCI Card test aborted 018-199-XXX PCI Card test failed, cause unknown 018-250-XXX PCI Card Services error 020-000-XXX PCI Interface Test Passed 020-0XX-XXX...
Page 105
Diagnostic Error Code 020-199-XXX PCI test failed, cause unknown 020-262-XXX PCI system error 025-000-XXX IDE interface Test Passed 025-00X-XXX 025-01X-XXX IDE interface failure 025-027-XXX IDE interface Configuration/Setup error 025-02X-XXX 025-03X-XXX 025-04X-XXX IDE Interface failure 025-195-XXX IDE interface Test aborted by user 025-196-XXX IDE interface test halt, error threshold exceeded...
Page 106
Diagnostic Error Code 030-00X-XXX 030-01X-XXX SCSI interface failure 030-027-XXX SCSI interface Configuration/Setup error 030-03X-XXX 030-04X-XXX SCSI interface error 030-195-XXX SCSI interface Test aborted by user 030-196-XXX SCSI interface test halt, error threshold exceeded 030-197-XXX SCSI interface test warning 030-198-XXX SCSI interface test aborted 030-199-XXX SCSI interface test failed, cause unknown 035-000-XXX...
Page 107
Diagnostic Error Code 035-196-XXX RAID interface test halt, error threshold exceeded 035-197-XXX RAID interface test warning 035-198-XXX RAID interface test aborted 035-199-XXX RAID interface test failed, cause unknown 071-000-XXX Audio port Interface Test Passed 071-00X-XXX 071-01X-XXX 071-02X-XXX Audio port error 071-03X-XXX Audio port failure 071-04X-XXX...
Page 108
Diagnostic Error Code 071-199-XXX Audio port test failed, cause unknown 071-25X-XXX Audio port failure 080-000-XXX Game Port interface Test Passed 080-XXX-XXX Game Port interface Error 080-195-XXX Game Port interface Test aborted by user 080-196-XXX Game Port interface test halt, error threshold exceeded 080-197-XXX Game Port interface test warning...
Page 109
Diagnostic Error Code 086-196-XXX Mouse Port interface test halt, error threshold exceeded 086-197-XXX Mouse Port interface test warning 086-198-XXX Mouse Port interface test aborted 086-199-XXX Mouse Port interface test failed, cause unknown 089-000-XXX Microprocessor Test Passed 089-XXX-XXX Microprocessor failure 089-195-XXX Microprocessor Test aborted by user 089-196-XXX Microprocessor test halt, error threshold...
Page 110
Diagnostic Error Code 170-195-XXX Voltage Sensor(s) Test aborted by user 170-196-XXX Voltage Sensor(s) test halt, error threshold exceeded 170-197-XXX Voltage Sensor(s) test warning 170-198-XXX Voltage Sensor(s) test aborted 170-199-XXX Voltage Sensor(s) test failed, cause unknown 170-250-XXX 170-251-XXX Voltage Sensor(s) Voltage limit error 170-254-XXX Voltage Sensor(s) Voltage Regulator Module error...
Page 111
Diagnostic Error Code 175-199-XXX Thermal Sensor(s) test failed, cause unknown 175-250-XXX 175-251-XXX Thermal Sensor(s) limit error 185-000-XXX Asset Security Test Passed 185-XXX-XXX Asset Security failure 185-278-XXX Asset Security Chassis Intrusion 201-000-XXX System Memory Test Passed 201-XXX-XXX System Memory error 202-000-XXX System Cache Test Passed 202-XXX-XXX System Cache error...
Page 112
Diagnostic Error Code 217-28X-XXX 217-29X-XXX Hard Disk Drive (SCSI) error 220-000-XXX Hi-Capacity Cartridge Drive Test Passed 220-XXX-XXX Hi-Capacity Cartridge Drive error 301-XXX-XXX Keyboard error 301-000-XXX Keyboard Test Passed 302-000-XXX Mouse Test Passed 302-XXX-XXX Mouse error 303-000-XXX Joystick Test Passed 303-XXX-XXX Joystick error 305-000-XXX Monitor DDC Test Passed...
Beep symptoms Beep symptoms are short tones or a series of short tones separated by pauses (intervals without sound). See the following examples. Beeps 1-2-X Use the following table to diagnose beep symptoms. Beep Symptom 1-1-3 CMOS read-write error 1-2-2-3 ROM BIOS check error 1-2-1 Programmable Interval Timer failed...
Page 114
Beep Symptom 2-2-4 CMOS configuration info validation failed 2-3-1 Screen initialization failed 2-3-2 Screen memory failed 2-3-3 Screen retrace failed 1-2 Search for video ROM failed All other beep code sequences Continuous beep Repeating short beeps Hardware Maintenance Manual FRU/Action 1.
No-beep symptoms Symptom/Error No beep during POST but computer works correctly. No beep during POST. FRU/Action 1. System Board 1. See “Undetermined problems” on page 127. 2. System Board 3. Memory Module 4. Any Adapter or Device 5. Riser Card 6.
POST error codes Each time you power-on the system, it performs a series of tests that check the operation of the system and some options. This series of tests is called the Power-On Self-Test, or POST. POST does the following operations. v Checks some basic system-board operations v Checks the memory operation v Starts the video operation...
Page 117
POST Error Code I/O channel parity error Adapter ROM error Internal cache test error 135 Fan failure System board failure Bad CMOS battery Configuration mismatch Date and Time Incorrect Memory Size Error Boot Block Check Sum Error No Processor BIOS Update Found FRU/Action 1.
Page 118
Asset Control Antenna not detected Corrupted boot sequence 186 Security Hardware Control Logic Error System Security: Invalid Remote Change Requested 191 System Security: IBM Embedded Security Hardware Reset 193 System Security: IBM Embedded Security Hardware Removed 194 System Security: Asset ID Antenna has...
Page 119
POST Error Code External cache test error POST detected a base memory or extended memory type error 301 Keyboard Error With an 8603 error With no 8603 error Not listed above And able to run diagnostics POST cannot unlock the diskette drive 662 Configuration Change has occured FRU/Action 1.
Page 120
POST Error Code Not listed above Math coprocessor configuration error Not listed above Parallel port configuration error 1047 107X Check SCSI terminator installation 1101 Serial connector error, possible system board failure 1101, 1102, 1106, 1108, 1109 1107 1102 Card selected feedback error 1103 Port fails register check 1106...
Page 121
POST Error Code 1117 Failed baud rate test 1162 Serial port configuration error 11XX Not listed above 1201 1202, 1206, 1208, 1209, 12XX 1207 13XX 1402 Printer not ready 1403 No paper error, or interrupt failure 1404 System board timeout failure 1405 Parallel adapter error 1406...
Page 122
POST Error Code 1800 PCI/PnP Error! No Hardware Interrupt Available 1801 PCI/PnP Error! No Space Available to Shadow ROM 1802 PCI/PnP Error! Not Enough I/O Space Available 1803 PCI/PnP Error! Not Enough Memory Space Available 1804 PCI/PnP Error! Not Enough Real Memory Space Available 1805 PCI/PnP Error! Adapter ROM Checksum Error...
Page 123
POST Error Code 180X, 188X PCI configuration or resource error 1962 No operating system found 209X 20XX Not listed above 21XX 2401, 2402 If screen colors change 2401, 2402 If screen colors are OK 2409 2410 2462 Video memory configuration error 4611, 4630 4612, 4613, 4640, 4641 4650...
Page 124
POST Error Code 5962 An IDE device (other than hard drive) configuration error 62XX 63XX 64XX 71XX 74XX 76XX 78XX 79XX 80XX 84XX 8601, 8602 8603, 8604 Pointing Device Error 86XX Not listed above 89XX 91XX 96XX 10101, 10102, 10104, 10105, 10106, 10107, 10108, 10109, 10111, 10112, 10113, 10114, 10115, 10116...
Page 125
3. External DAA (if installed) 4. Modem 1. Run Diagnostics and verify the correct operation of the modem slot 2. Modem 1. Diagnostics detected a non-IBM modem 2. Modem 1. Check PSTN Cable 2. External DAA (if installed) 3. Modem 1.
Page 127
POST Error Code 119XX 121XX 136XX 137XX 141XX 143XX 14710, 14711 148XX 14901, 14902, 1491X, 14922 14932 161XX 164XX 16500 16520, 16540 166XX, 167XX 18001 to 18029 18031 to 18039 FRU/Action 1. 3119 Adapter 1. Modem Adapter 2. Any Serial Device 3.
Page 128
POST Error Code 185XXXX 20001 to 20003 20004 20005 to 20010 200XX Not listed above 20101 to 20103 20104 20105 to 20110 Image Adapter/A Memory Test failure indicated by graphic of adapter 206XX 208XX Verify there are no duplicate SCSI ID settings on the same bus.
Page 129
POST Error Code Tape Drive green ″in use″ LED fails to come Tape automatically ejected from drive SCSI ID on rotary switch does not match SCSI ID set in configuration. Verify drive switches inside cover are set to zero Tape sticks or breaks in drive. Verify that the tapes used meet ANSI standard X3B5 212XX...
Page 130
POST Error Code 27512 27535 27554 27555, 27556 27557 27558, 27559, 27560, 27561 27562 27563, 27564 275XX 27801 to 27879 27880 to 27889 999030X Hard disk reset failure Hardware Maintenance Manual FRU/Action 1. WMSELF.DGS diagnostics file is missing 2. WMSELF.DGS diagnostics file is incorrect 1.
Miscellaneous error messages Message/Symptom CMOS Backup Battery inaccurate Changing colors Computer will not power-off. See “Power Supply Errors” on page 87. Computer will not RPL from server Computer will not Wake On LAN (if applicable) Dead computer. See “Power Supply Errors” on page 87.
Page 132
Message/Symptom ″Insert a Diskette″ icon appears with a known-good diagnostics diskette in the first 3.5-inch diskette drive. Intensity or color varies from left to right of characters and color bars No power or fan not running Non-system disk or disk error-type message with a known-good diagnostic diskette.
1. Power-off the computer. 2. Remove or disconnect the following components (if installed) one at a time. a. Non-IBM devices b. External devices (modem, printer, or mouse) c. Any adapters d.
Page 199
Recovery CDs Win XP Home Swedish Hebrew Finnish Norwegian Polish Portuguese Russian Hungarian Czechoslovakian Turkish Greek Japanese Simplified Chinese Traditional Chinese Traditional Chinese Hong Kong Recovery CDs Win XP Pro US English (Models 12G 16A A2G 21G 26A 31G 35A 15G A5G 22G 32G 13G A3G 25G 34G 17A 27A 36A 19A 29A 38A 18G A4G 28G 37G B1A B2A 52A 5BA 62G 63A 64A 65A 71G 72G 73G 74G 75G 76G 7AG...
Page 209
Machine Type 8313 Speaker Power brick - US CE CF LA Taiwan (models 52U 52S 52D 52Y 5BU 5BS 5BP 5BD 5BY B2U B2S B2D B2Y B4U B4S B4D B4Y B6U B6S B6D B6Y B8U B8F) Speaker Power brick - Brazil (models 52P B4P B6P) RJ11 connector adapter (Spain Ireland) (all ″G″...
Page 210
Hardware Maintenance Manual Recovery CDs Win 2K US (model 54G) FR (model 54G) GR (model 54G) IT (model 54G) SP (model 54G) DK (model 54G) NL (model 54G) AE (model 54G) SV (model 54G) HE (model 54G) FI (model 54G) NO (model 54G) PL (model 54G) PO (model 54G)
Page 211
Recovery CDs Win XP Home Portuguese Russian Hungarian Czechoslovakian Turkish Greek Japanese Simplified Chinese Traditional Chinese Traditional Chinese Hong Kong Recovery CDs Win XP Pro US English (Models 33G 11G A1G 23U 23G 33U 43U 12G A2G 24G 51G 52G 53U 55U 5AG 5CU 5DU 61G 62U 81U 91U B1U B3U) French (models 33G 11G A1G 23G 12G A2G 24G 51G 52G 55F 5AG 5DF 61G 62F 81F 91F B1F)
Page 230
Hardware Maintenance Manual Recovery CDs Win XP Pro Turkish (models 61G) Greek (models 61G) Simplified Chinese (models 61C) Traditional Chinese (models 61V) Traditional Chinese Hong Kong (model 61B) Keyboards (PS/2 Black) US English (models 61U 61G 61A 61C 61H) Arabic (models 61G) Belgian/French (models 61G) Belgian/UK (models 61G) Bulgarian (models 61G)
Page 231
Keyboards (PS/2 Black) Turkish (models 61G) UK English (models 61G) US International (models 61G) Yugoslav/Latin (models 61G) Brazil/Portuguese (models 61P) Power Cords Line Cord (models 61U 61F 61S 61P 61G 61A 61T 61V) Line Cord (model 61A) Line Cord (models 61G 61A) Line Cord (models 61G 61A 61H) Line Cord (models 61G) Line Cord (models 61S 61P 61G)
Page 265
Recovery CDs Win XP Home Hungarian Czechoslovakian Turkish Greek Japanese Simplified Chinese Traditional Chinese Traditional Chinese Hong Kong Recovery CDs Win XP Pro US English (models 11U 23U 37U 42U 53U 5DU 61U 91U B1U B6U B8U 25U) French (model 25F) German Italian Spanish (models 53S 53D 53Y B1S B6S B8S)
Page 266
Hardware Maintenance Manual Keyboards (PS/2 Black) Belgian/French Belgian/UK Bulgarian Chinese/US Czech Danish Dutch French French Canadian (models B3F 25F) French Canadian (models B3F 25F) German Greek Hebrew Hungarian Iceland Italian Japanese (model CAJ) Korean LA Spanish (models 51S 51D 51Y 5AS 5AD 5AY 5BS 5BD 5BY 52S 52D 52Y 53S 53D 53Y B1S B2S B2D B2Y B4S B4D B4Y B5S B5D B5Y B6S B7S B7D B7Y B8S) Norwegian...
Page 267
Keyboards RAK III Lite US English Arabic Belgian/French Belgian/UK Bulgarian Chinese/US Czech Danish Dutch French French Canadian French Canadian German Greek Hebrew Hungarian Iceland Italian Japanese LA Spanish (models 21S 21D 21Y 38S 38D 38Y 41S 41D 41Y) Norwegian Polish Portuguese Romanian Russian...
To update the EPROM using the DMI MIF Browser, use the following procedure. 1. Click Start from the desktop, then Programs. 2. Select IBM SystemView Agent 3. Select the Serial Number Information icon 4. Click the plus sign to expand.
BIOS. v Current Level BIOS information – Run the Configuration Utility to determine the level of BIOS installed. v Sources for determining the latest level BIOS available 1. IBM Home Page http://www.ibm.com/pc/us/ 2. PC PartnerInfo-Technical Database (CTSTIPS.NSF) 3. HelpCenter 4.
Flash from Operating System (WinPhlash) Attention: Refer to the information label located inside the system unit cover for any model-specific information. Click the file link to download the file (24jyNNusa.exe) from the web page. 2. When prompted, select a drive and directory in which to save the downloaded file.
8. Click Finish. You will be prompted with a message stating ″The specified output folder does not exist. Create it?″ 9. Click Yes. You will be prompted with a message stating ″The package has been delivered successfully.″ 10. Click OK. 11.
Page 274
Flash/BIOS Update process to follow after performing a boot block recovery process: 1. After replacing the cover, insert the upgrade floppy disk into the disk drive and turn on the computer. The IBM Logo will appear. 2. When the Flash Update Utility appears, select the country/keyboard, then press enter.
Power management Power management reduces the power consumption of certain components of the computer such as the system power supply, processor, hard disk drives, and some monitors. Advanced Power Management and Rapid Resume features of some personal computers. Automatic configuration and power interface (ACPI) BIOS Being an ACPI BIOS system, the operating system is allowed to control the power management features of the computer and the setting for Advanced Power Management (APM) BIOS mode are ignored.
Wake on LAN: If the computer has a properly configured token-ring or Ethernet LAN adapter card that is Wake on LAN-enabled and there is remote network management software, you can use the IBM-developed Wake on LAN feature. When you set Wake on LAN to Enabled, the computer will turn on when it receives a specific signal from another computer on the local area network (LAN).
Safety information The following section contains the safety information that you need to be familiar with before servicing an IBM computer. General safety Follow these rules to ensure general safety: v Observe good housekeeping in the area of the machines during and after maintenance.
Electrical safety CAUTION: Electrical current from power, telephone, and communication cables can be hazardous. To avoid personal injury or equipment damage, disconnect the attached power cords, telecommunication systems, networks, and modems before you open the server/workstation covers, unless instructed otherwise in the installation and configuration procedures.
This guide addresses only those items. However, good judgment should be used to identify potential safety hazards due to attachment of non-IBM features or options not covered by this inspection guide.
Insulation must not be frayed or worn. 4. Remove the cover. 5. Check for any obvious non-IBM alterations. Use good judgment as to the safety of any non-IBM alterations. 6. Check inside the unit for any obvious unsafe conditions, such as metal filings, contamination, water or other liquids, or signs of fire or smoke damage.
Grounding requirements Electrical grounding of the computer is required for operator safety and correct system function. Proper grounding of the electrical outlet can be verified by a certified electrician. Safety notices (multi-lingual translations) The caution and danger safety notices in this section are provided in the following languages: v English v Brazilian/Portuguese...
Page 282
CAUTION: When replacing the lithium battery, use only IBM Part Number 33F8354 or an equivalent type battery recommended by the manufacturer. If your system has a module containing a lithium battery, replace it only with the same module type made by the same manufacturer. The battery contains lithium and can explode if not properly used, handled, or disposed of.
Page 283
CAUTION: The power control button on the device and the power switch on the power supply do not turn off the electrical current supplied to the device. The device also might have more than one power cord. To remove all electrical current from the device, ensure that all power cords are disconnected from the power source.
Page 284
5. LIGUE os dispositivos. CUIDADO: Ao substituir a bateria de lítio, utilize apenas uma bateria IBM, Número de Peça 33F8354 ou uma bateria de tipo equivalente, recomendada pelo fabricante. Se o seu sistema possui um móídulo com uma bateria de lítio, substitua-o apenas pelo mesmo tipo de mídulo, do mesmo fabricante.
Page 285
Para descartar a bateria, entre em contato com a área de atendimento a clientes IBM, pelo telefone (011) 889-8986, para obter informações sobre como enviar a bateria pelo correio para a IBM. PRECAUCIÓN: Quando produtos a laser (unidades de CD-ROM, unidades de DVD, dispositivos de fibra ítica, transmissores, etc.) estiverem instalados, observe o seguinte:...
Page 286
fonte de energia elétrica. CUIDADO: CUIDADO: Não coloque nenhum objeto com peso superior a 82 kg (180 lbs.) sobre dispositivos montados em rack. Hardware Maintenance Manual...
Page 287
Chapter 10. Related service information...
Page 295
ATTENTION: Remplacez la pile au lithium usagée par une pile de référence identique exclusivement - voir la référence IBM - ou par une pile équivalente recommandée par le fabricant. Si votre système est doté d’un module contenant une pile au lithium, vous devez le remplacer uniquement par un module identique, produit par le même fabricant.
Page 296
Pour la mise au rebut, reportez-vous à la réglementation en vigueur. ATTENTION: Si des produits laser sont installés (tels que des unités de CD-ROM ou de DVD, des périphériques contenant des fibres optiques ou des émetteurs-récepteurs), prenez connaissance des informations suivantes: v N’ouvrez pas ces produits pour éviter une exposition directe au rayon laser.
Page 297
courant. ATTENTION: Ne posez pas d’objet dont le poids dépasse 82 kg sur les unités montées en armoire. Chapter 10. Related service information...
Page 298
4. Netzstecker an Steckdose anschließen. 5. Gerät einschalten. ACHTUNG: Eine verbrauchte Batterie nur durch eine Batterie mit der IBM Teilenummer 33F8354 oder durch eine vom Hersteller empfohlene Batterie ersetzen. Wenn Ihr System ein Modul mit einer Lithium-Batterie enthält, ersetzen Sie es immer mit dem selben Modultyp vom selben Hersteller.
Page 299
Die örtlichen Bestimmungen für die Entsorgung von Sondermüll beachten. ACHTUNG: Wenn ein Laserprodukt (z. B. CD-ROM-Laufwerke, DVD-Laufwerke, Einheiten mit Glasfaserkabeln oder Transmitter) installiert ist, beachten Sie folgendes. v Das Entfernen der Abdeckungen des CD-ROM-Laufwerks kann zu gefährlicher Laserstrahlung führen. Es befinden sich keine Teile innerhalb des CD-ROM-Laufwerks, die vom Benutzer gewartet werden müssen.
Page 300
werden, daß alle Netzkabel aus den Netzsteckdosen herausgezogen wurden. ACHTUNG: Keine Gegenstände, die mehr als 82 kg wiegen, auf Rack-Einheiten ablegen. Hardware Maintenance Manual...
Page 301
5. ACCENDERE le unità. ATTENZIONE: Quando si sostituisce la batteria al litio, utilizzare solo una batteria IBM con numero parte 33F8354 o batterie dello stesso tipo o di tipo equivalente consigliate dal produttore. Se il sistema di cui si dispone è provvisto di un modulo contenente una batteria al litio, sostituire tale batteria solo con un tipo di modulo uguale a quello fornito dal produttore.
Page 302
Smaltire secondo la normativa in vigore (D.Lgs 22 del 5/2/9) e successive disposizioni nazionali e locali. ATTENZIONE: Quando si installano prodotti laser come, ad esempio, le unità DVD, CD-ROM, a fibre ottiche o trasmettitori, prestare attenzione a quanto segue: v Non rimuovere i coperchi. L’apertura dei coperchi di prodotti laser può determinare l’esposizione a radiazioni laser pericolose.
Page 303
siano scollegati dalla sorgente di alimentazione. ATTENZIONE: Non poggiare oggetti che pesano più di 82 kg sulla parte superiore delle unità montate in rack. Chapter 10. Related service information...
Page 307
PRECAUCIÓN: Cuando desee sustituir la batería de litio, utilice únicamente el número de pieza 33F8354 de IBM o cualquier tipo de batería equivalente que recomiende el fabricante. Si el sistema tiene un mídulo que contiene una batería de litio, sustitúyalo únicamente por el mismo tipo de mídulo, que ha de estar creado por el mismo fabricante.
Page 308
v Calentarla a una temperatura que supere los 100°C (212°F) v Repararla o desmontarla Despréndase de la batería siguiendo los requisitos que exija el reglamento o la legislaciín local. PRECAUCIÓN: Cuando instale productos láser (como, por ejemplo, CD-ROM, unidades DVD, dispositivos de fibra íptica o transmisores), tenga en cuenta las advertencias siguientes: v No retire las cubiertas.
Page 309
El botín de control de alimentaciín del dispositivo y el interruptor de alimentaciín de la fuente de alimentaciín no apagan la corriente eléctrica suministrada al dispositivo. Es posible también que el dispositivo tenga más de un cable de alimentaciín. Para eliminar la corriente eléctrica del dispositivo, asegúrese de desconectar todos los cables de alimentaciín de la fuente de alimentaciín.
We want to know your opinion about this manual (part number 24P2934). Your input will help us to improve our publications. Please photocopy this survey, complete it, and then fax it to IBM HMM Survey at 919-543-8167 (USA). Name: _________________________________________...
IBM intends to make these available in all countries in which IBM operates. Any reference to an IBM product, program, or service is not intended to state or imply that only that IBM product, program, or service may be used. Subject to IBM’s valid intellectual property or other legally protectable rights, any...
Trademarks The following terms are trademarks of the IBM Corporation in the United States, other countries, or both: Lotus and Domino are trademarks of Lotus Development Corporation in the United States, other countries, or both. Intel and Celeron are registered trademarks of Intel Corporation.
Page 314
Part Number: 24P2969 Printed in USA (1P) P/N: 24P2969...