Modulation Effects Parameters; Utilities - DigiTech GeNetX BNX3 User Manual

Grn LeVL
(Green Level) - Controls the Volume of the Green Channel.
Red GAIN
(Red Gain) - Controls the Amp Gain for the Red Channel.
Red LeVL
(Red Level) - Controls the Volume of the Red Channel.
gatonoff (Noise Gate On/Off) - Turns the Noise Gate on and off.
gatthres
(Noise Gate Threshold) - Controls the Noise Gate's Threshold.
gatattak
(Noise Gate Attack) - Controls the Noise Gate's Attack time.
PLK SENS
(Noise Gate Pluck) - Controls the Noise Gate's Pluck Sensitivity.
fx onoff
(Chorus/Mod On/Off) - Turns the Chorus/Mod module on and off.

Modulation Effects Parameters

Active Effect
Chorus
Flanger
Phaser
Tremolo
Panner
Vibrato
Rotary Speaker
Auto Ya™
YaYa™
Detune
Pitch Shift
dly onoff
(Delay On/Off) - Turns the Delay module on and off.
DLY fdbk
(Delay Feedback) - Controls the amount of Delay Feedback.
dukthres
(Delay Threshold) - Controls the Ducker Threshold for the Delay.
duk attn (Ducker Attenuation) - Controls the attenuation level applied to the Delay signal when the
Ducker Threshold is exceeded.
DLY levl
(Delay Level) - Controls the Mix Level of the selected Delay Type.
DLY BAL
(Delay Balance) - Controls the left/right balance of the selected Delay Type.
rvbonoff
(Reverb On/Off) - Turns the Reverb effect on and off.
RVB PRE
(Reverb Predelay) - Controls the Reverbs Predelay time.
rvbdecay
(Reverb Decay) - Controls the Reverbs Decay time.
RVB levl
(Reverb Level) - Controls the Reverbs Mix Level.
RVB BAL
(Reverb Balance) - Controls the left/right balance of the selected Reverb Type.
VOL PRE
(Volume Pre) - Controls the Volume after the Amp Modeling but before the Effects.
VOL PoST
(Volume Post) - Controls the Volume at the end of the Effects chain.
LFo1 SPD
(LFO 1 Speed) - Controls the modulation speed of Expression LFO 1.
LFo2 SPD
(LFO 2 Speed) - Controls the modulation speed of Expression LFO 2.

Utilities

The Utility section contains all of the menus for assigning global functions to the BNX3. Global functions
affect the BNX3 in its entirety rather than on a per preset basis.The Utility menus include: Mono/Stereo
Output, Bi-Amp Output, Volume Pedal Update,V-Switch Threshold, Expression Pedal Calibration, Dry Track
Enable, Bank Naming, MIDI Channel, MIDI Sysex Dumps, Amp Dumps, MIDI Mapping, MIDI Merge, and
Factory Reset.To enter the Utility section, press the Utility button. Once in the Utility menu, the Drums
button selects the next menu (scrolls to the right), and the Mode button selects the previous menu (scrolls
to the left). Each of these Utility menus is described in more detail in the following pages.
Speed Depth
Speed Depth
Speed Depth
Speed Depth
Speed Depth
Speed Depth
Speed Depth
Speed Depth
YA PeDaL Depth
Amount MOD cntr
SHIFT MOD cntr
Other Functions
predelay MOD Bal
Regen MOD Bal
Regen MOD Bal
Doppler crosover
RANGE MOD Bal
RANGE MOD Bal
MOD LVL
MOD LVL
MOD LeVeL
MOD MIX
MOD MIX
MOD BAL MOD MIX
MOD MIX
MOD MIX
65