Trane TR150 Programming Manual page 71

Parameters
16-11 Power [hp]
Range:
0 hp [0 - 1000
*
hp]
3 3
16-12 Motor Voltage
Range:
0 V [0 - 65535 V] View the motor voltage, a calculated value
*
16-13 Frequency
Range:
0 Hz [0 - 6553.5 Hz] View the motor frequency, without
*
16-14 Motor current
Range:
0 A [0 - 655.35 A] View the motor current measured as a
*
16-15 Frequency [%]
Range:
0 % [0 - 6553.5
*
%]
16-18 Motor Thermal
Range:
0 % [0 -
*
100 %]
3.12.3 16-3* Drive Status
16-30 DC Link Voltage
Range:
0 V [0 - 65535 V]
*
16-34 Heatsink Temp.
Range:
0 °C [-128 - 127 °C] View the heat sink temperature of the
*
16-35 Inverter Thermal
Range:
0 % [0 - 255 %] View the percentage of thermal load on the
*
70
TR150 Programming Guide
Function:
View the DC link power in hp. The value
shown is calculated on the basis of the
actual motor voltage and motor current.
Function:
used for controlling the motor.
Function:
resonance dampening.
Function:
mean value, IRMS.
Function:
View a 2-byte word reporting the actual
motor frequency (without resonance
dampening) as a percentage (scale
0000-4000 Hex) of 4-19 Max Output
Frequency.
Function:
View the calculated motor temperature in
percentage of allowed maximum. At 100% a trip
will occur, if selected in 1-90 Motor Thermal
Protection. The basis for the calculation is the ETR
function selected in 1-90 Motor Thermal
Protection.
Function:
View a measured value.
Function:
frequency converter.
Function:
frequency converter. At 100% a trip occurs.
16-36 Inv. Nom. Current
Range:
0 A [0 - 655.35
*
A]
16-37 Inv. Max. Current
Range:
0 A [0 - 655.35 A] View the inverter maximum current. The
*
16-38 SL Controller State
Range:
0 [0 - 20 ] View the actual state of the Smart Logic Controller
*
3.12.4 16-5* Ref. & Feedb.
16-50 External Reference
Range:
0 % [-200 - 200
*
%]
16-52 Feedback[Unit]
Range:
0 ProcessCtrlUnit
3.12.5 16-6* Inputs and Outputs
16-60 Digital Input
Range:
0 [0 -
*
65535 ]
BAS-SVP16A-EN - Rev. 2013-09-05
Function:
View the inverter nominal current, which
should match the nameplate data on the
connected motor. The data are used for
motor protection, etc.
Function:
data are used for calculation of frequency
converter protection, etc.
Function:
(SLC).
Function:
View the total reference, the sum of
digital, analog, preset, bus and freeze
references.
Function:
[-4999 - 4999 View the feedback
*
ProcessCtrlUnit] resulting from the
selection of scaling in
3-02 Minimum Reference
and 3-03 Maximum
Reference.
Function:
View actual state of the digital inputs 18, 19, 27
and 29.
Bit 0 Unused
Bit 1 Unused
Bit 2 Digital input term. 29
Bit 3 Digital input term. 27
Bit 4 Digital input term. 19
Bit 5 Digital input term. 18
Bit 6~15 Unused
Table 3.8 Bits Definition