Electrical Connections; Identification Of Wiring - Hussmann INSIGHT REACH-IN Installation & Operation Manual

Signal words and safety symbols that are used in a product's collateral materials or on the product may
be defined in collateral materials if space is available.

ELECTRICAL CONNECTIONS

A1.1 Safety Alert Symbol
The meaning of the safety alert symbol may be provided in collateral materials. The following artwork may
All wiring must be in compliance with NEC and local codes. All electrical
be used for this purpose.
connections are to be made to the terminal blocks in the electrical
wireway behind the lower front panel at the right-hand end of the
merchandiser (facing front).

IDENTIFICATION OF WIRING

A1.2 Signal Words
Leads for all electrical circuits are identified by colored plastic bands.
The meaning of the different signal words as defined by the ANSI Z535.6 and ANSI Z535.4 standards
may be explained in collateral materials. The following artwork may be used for this purpose.
These bands correspond to the color code sticker (shown below)
located inside the merchandiser wireway.
— LOCK OUT / TAG OUT —
»
Merchandiser must be grounded. All wiring must be in
compliance with NEC and local codes.
»
To avoid serious injury or death from electrical shock,
always disconnect the electrical power at the main
disconnect when servicing or replacing any electrical
component. This includes, but is not limited to, such items
as doors, lights, fans, heaters, and thermostats.
A1.3 Other Highlighting Conventions
The meaning of any other highlighting conventions used to differentiate safety messages (e.g., text
manipulations, indention, etc.) may be explained in collateral materials.
A1.4 Safety Symbols
Leads for all electrical circuits are identified by a colored plastic band: neutral wire for each circuit has
The meaning of any safety symbols used on safety labels or collateral materials may be explained in
collateral materials.
either White insulation or a White plastic sleeve in addition to the color band.
P
Copyright National Electrical Manufacturers Association
L
Provided by IHS Markit under license with NEMA
No reproduction or networking permitted without license from IHS
D
P
B
g
HUSSMANN CORPORATION • U.S. & CANADA 1-800-922-1919 • BRIDGETON, MO 63044-2483 • MEXICO 1-800-890-2900 • WWW.HUSSMANN.COM • PN 3181178_A
This is the safety alert symbol. It is used to alert you
to potential physical injury hazards. Obey all safety
messages that follow this symbol to avoid possible
injury or death.
DANGER indicates a hazardous situation which, if not
avoided, will result in death or serious injury.
WARNING indicates a hazardous situation which, if not
avoided, could result in death or serious injury.
CAUTION indicates a hazardous situation which, if not
avoided, could result in minor or moderate injury.
NOTICE is used to address practices not related to
physical injury.
Safety instructions (or equivalent) signs indicate specific
safety-related instructions or procedures.
© 2017 National Electrical Manufacturers Association
............ R . T
ink efRig heRmosTaT
B .. R . T
Licensee=Hussmann Corp/8160899001, User=Trevett, Jason
ighT Lue efRig heRmosTaT
Not for Resale, 02/16/2021 11:49:55 MST
B .. D T . T
aRk Lue efRosT eRm heRmosTaT
........ a -s h
uRPLe nTi weaT eaTeRs
........ f m
Rown an oToRs
* ....... g
Reen RounD
*e
iTheR coLoReD
ELECTRICIAN NOTE: Use copper conductor wire only.
T
hese aRe maRkeR coLoRs wiRes maY VaRY
»
Terminal block NOT for case-to-case wire connection.
The Disconnect Switch is
located in the electrical
panel on top of the case.
Copyright National Electrical Manufacturers Association
Provided by IHS Markit under license with NEMA
No reproduction or networking permitted without license from IHS
WIRING COLOR CODE
L T . o
ow emP Range oR
n T . T .............L
oRm emP an
m ......R
aRoon
Y * ......D
eLLow
R * ...........D
eD
s o c i
LeeVe R oLoReD nsuLaTion
CASE MUST BE GROUNDED
2-9
The meaning of the different signal words as defined by the ANSI Z535.6 and ANS
may be explained in collateral materials. The following artwork may be used for thi
A1.3 Other Highlighting Conventions
The meaning of any other highlighting conventions used to differentiate safety mes
manipulations, indention, etc.) may be explained in collateral materials.
A1.4 Safety Symbols
The meaning of any safety symbols used on safety labels or collateral materials m
collateral materials.
© 2017 National Electrical Manufacturers Association
ighTs
ecePTacLes
h , 120V
efRosT eaTeRs
h , 208V
efRosT eaTeRs
.
DANGER indicates a hazardous situati
avoided, will result in death or serio
WARNING indicates a hazardous situa
avoided, could result in death or se
CAUTION indicates a hazardous situat
avoided, could result in minor or mo
NOTICE is used to address practices n
physical injury.
Safety instructions (or equivalent) signs
safety-related instructions or proced
Licensee=Hussmann Corp/8160899001, User=Trevett, Ja
Not for Resale, 02/16/2021 11:49:55 MST