Boss JamStation JS-5 Owner's Manual page 148

MIDI Implemantation
Hold 1
Status 2nd byte
BnH 040H
n=MIDI channel : 1H-3H, 9H (ch. 2, 3, 4, 10)
vv=Control value : 00H-7FH (0-127) 0-63=OFF 64-127=ON
Effect1 (Reverb Level / Delay Feedback)
Status 2nd byte
BnH 5BH
n=MIDI channel : 1H-3H, 9H (ch. 2, 3, 4, 10)
vv=Control value : 00H-7FH (0-127)
* This message determines the level of Reverb when the selected Effect is Reverb, or delay
level when the selected effect is Delay.
* For some instruments within the drum kit, the reverb/delay effect may not apply.
Effect3 (Chorus Level)
Status 2nd byte
BnH 5DH
n=MIDI channel : 1H-3H, 9H (ch. 2, 3, 4, 10)
vv=Control value : 00H-7FH (0-127)
* Flanger effect is not obtained if the Flanger send level of each instrument in the Drum kit
is not set at high.
* For some instruments within the drum kit, the chorus effect may not apply.
RPN MSB/LSB
Status 2nd byte
BnH 65H
BnH 64H
n=MIDI channel : 1H-3H, 9H (ch. 2, 3, 4, 10)
mm=MSB of parameter specified by RPN
ll=LSB of parameter specified by RPN
**RPN**
Control Changes include RPN (Registered Parameter Numbers), which are extended
parameters whose function is defined in the MIDI specification.
RPN can be used to change instrument parameters.
When using RPNs, first the RPN (Controller numbers 100 and 101; they can be sent in any
order) is transmitted to specify the parameter you wish to control. Then, Data Entry
messages (Controller numbers 6 and 38) are used to set the value of the specified parameter.
Once a RPN parameter has been specified, all further Data Entry messages on that channel
are considered to apply to that specified parameter. In order to prevent accidents, when the
desired setting has been made for the parameter, it is recommended that RPN be set to Null.
RPN Data Entry
MSB LSB MSB LSB
00H 00H mmH --
00H 01H mmH llH
00H 02H mmH --
7FH 7FH -- --
Program Change
Status 2nd byte
CnH ppH
n=MIDI channel : 1H-3H, 9H (ch. 2, 3, 4, 10)
pp=Program number : 00H-7FH (prog.1-prog.128)
* The first Note On after receiving a Program change sounds a voice with a new tone with
exception of the voices which have been sounded before the Program change is received.
148
3rd byte
vvH
3rd byte
vvH
3rd byte
vvH
3rd byte
mmH
llH
Pitch Bend Sensitivity
mm: 00H-18H (0-24 semitones)
Up to 2 octaves, default settings 12 semitones.
This setting becomes effective for subsequent
Pitch Bend messages.
Master Fine Tuning
mm, ll: 00H, 00H-40H, 00H-7FH, 7FH
(-8192 x 100/8192 - 0 - +8192 x 100/8192 cent)
Coarse Tuning
mm: 10H-40H-70H (-48 - 0 - +48 semitones)
RPN reset
No specified parameter is assigned to RPN and
NRPN.
Current value is not affected.
Pitch Bend Change
Status 2nd byte
EnH llH
n=MIDI channel : 1H-3H, 9H (ch. 2, 3, 4, 10)
mm, ll=Pitch bend value : 00H, 00H-40H, 40H-7FH, 7FH (-8192 - 0 - +8191)
Channel Mode Message
All Sound Off
Status 2nd byte
BnH 78H
n=MIDI channel : 1H-3H, 9H (ch. 2, 3, 4, 10)
* All current active voice in the specified channel will be shut off.
Reset All Controllers
Status 2nd byte
BnH 79H
n=MIDI channel : 1H-3H, 9H (ch. 2, 3, 4, 10)
* The following control values on the specified channel return to the default value.
Controller Default Value
Modulation 0 (min)
Volume 123 (max)
Panpot 64 (center)
Expression 127 (max)
Hold1 0 (off)
RPN/NRPN No specified parameter / No change in value
Pitch Bend Change 0
All Note Off
Status 2nd byte
BnH 7BH
n=MIDI channel : 1H-3H, 9H (ch. 2, 3, 4, 10)
* All active voices on the specified channel are turned off. (Each voice responds as to a
Note Off.) If Hold1 is ON, this message does not become effective until Hold is OFF.
Drum track ignores this message.
System Exclusive Message
Status Data byte
F0H iiH, ddH, ..., eeH
F0H : System Exclusive
ii=ID number : 41=Roland
7E=Universal Non-Realtime Message
dd, ..., ee=Data: 00H-7FH (0-127)
F7H : EOX (End Of Exclusive)
* With the JS-5, the System Exclusive Messages can be used to transmit Bulk Dump of
Song/Style data and System data. For details refer to p. 134.
System Common Message
Recognized only when the JS-5 is in stop and MIDI Sync mode is set at MIDI.
Song Position Pointer
Status 2nd byte
F2H llH
mm, ll =Value : 00H, 00H-7F, 7FH (0-16383)
* If the JS-5 receive Song Position Pointer, it calls the position in the song.
3rd byte
mmH
3rd byte
00H
3rd byte
00H
3rd byte
00H
Status
F7H
3rd byte
mmH