Pentax EPK-i7010 Instructions For Use Manual page 84

Select [Enable] or [Disable]. If you select [Enable], the settings for [IP address], [Subnet mask], and [Default
gateway] become invalid.
[IP address] / [Subnet mask] / [Default gateway]
Follow the procedure below to enter or change settings.
1 Press the [] or [] key to select an item when entering the four items separated by "."
2 Press the alphanumeric keys or the keys on the numeric keypad to enter or change the numbers. Each press
of the [Backspace] key deletes one character on the left of the cursor. Each press of the [Delete] key deletes
one character on the right of the cursor.
[Password]
Press the alphanumeric keys to enter a password. Only alphanumeric characters can be used (a to z, A to Z,
and 0 to 9) and up to 12 characters can be entered. The password is case sensitive. Leave the field blank if
you do not wish to set a password.
[Authorization]
Configure the network settings for the connection destination. Use the numeric keypad to configure of the
[Connect ID] settings. Use alphanumerical keys to enter the Connect ID. The number of characters that can be
used for the connect ID is between 6 and 12. Alphabet use in the connect ID is case sensitive.
• [iPro setup] (when [Network] is set to [TCP/IP])
[Processor setup]
[DHCP mode]
Select [Enable] or [Disable]. If you select [Enable], the settings for [IP address], [Subnet mask], and [Default
gateway] become invalid.
[IP address] / [Subnet mask] / [Default gateway]
Follow the procedure below to enter or change settings.
1 Press the [] or [] key to select an item when entering the four items separated by "."
2 Press the alphanumeric keys or the keys on the numeric keypad to enter or change the numbers. Each press
of the [Backspace] key deletes one character on the left of the cursor. Each press of the [Delete] key deletes
one character on the right of the cursor.
[Password]
Press the alphanumeric keys to enter a password. Only alphanumeric characters can be used (a to z, A to Z,
5
and 0 to 9) and up to 12 characters can be entered. The password is case sensitive. Leave the field blank if
you do not wish to set a password.
[iGate setup]
[iGate address] / [Gateway port] / [Active port] / [Maintenance port]
Follow the procedure below to enter or change settings.
1 Press the [] or [] key to select an item when entering the four items separated by "."
2 Press the alphanumeric keys or the keys on the numeric keypad to enter or change the numbers. Each press
of the [Backspace] key deletes one character on the left of the cursor. Each press of the [Delete] key deletes
one character on the right of the cursor.
 Do not operate the processor when there is an IP address conflict.
 Once an IP address conflict occurs, set the correct IP address, and turn the processor off and then on again.
[Lamp]
Turn the lamp on or off.
• [On] Turn on the lamp.
• [Off] Turn off the lamp.
[Pump]
Set the pump level or operate/stop the pump.
• [Pump level]
• [On]
• [Off]
[White balance]
Set the white balance of the endoscope.
• [White balance]
• [R gain]
• [B gain]
• [Reload]
79
Operating Procedure
Press [] or [] key to set the pump to one of five levels.
Operate the pump.
Turn off the pump.
Adjust the white balance of the connected endoscope.
Display the red gain value of the endoscope (K series only). Press the [] or [] key to adjust the
value. Pressing the [Alt] key and [] or [] key simultaneously increases or decreases the value
in increments of 10.
Display the blue gain value of the endoscope (K series only). Press the [] or [] key to adjust
the value. Pressing the [Alt] key and [] or [] key simultaneously increases or decreases the
value in increments of 10.
Restore the state before the white balance was adjusted.(K series only)