Omron E5GC User Manual page 412

Control Period (Cooling) ........................................ 6-46
Control Period (Heating) ........................................ 6-46
Dead Band ......................................................5-8, 6-30
Decimal Point ......................................................... 6-43
Derivative Time ...................................................... 6-28
Derivative Time (Cooling) ......................4-14, 5-9, 6-29
Digit Shift ............................................................... 6-89
Direct Setting of Position Proportional MV .... 5-32, 6-87
Direct/Reverse Operation ...................................... 6-47
Display Brightness ................................................. 6-69
Display Refresh Period .......................................... 6-93
Event Input Assignment ......................................... 5-12
Event Input Assignment 1 to 6 ............................... 6-56
event inputs ........................................................... 5-11
Extraction of Square Root Enable ................ 5-51, 6-59
Extraction of Square Root Low-cut Point ...... 5-51, 6-36
HB ON/OFF ........................................................... 6-64
Heater Burnout Detection 1 ................................... 6-22
Heater Burnout Detection 2 ................................... 6-23
Heater Burnout Hysteresis .................................... 6-65
Heater Burnout Latch ............................................ 6-65
Heater Current 1 Value Monitor .................... 6-10, 6-22
Heater Current 2 Value Monitor .................... 6-11, 6-23
Heating/Cooling Tuning Method ......................5-9, 6-88
HS Alarm 1 ............................................................ 6-24
HS Alarm 2 ............................................................ 6-25
HS Alarm Hysteresis ............................................. 6-77
HS Alarm Latch ..................................................... 6-77
HS Alarm Use ............................................... 4-42, 6-76
Hysteresis .............................................................. 4-21
Hysteresis (Cooling) .............................................. 6-31
Hysteresis (Heating) .............................................. 6-31
Initial Setting/Communications Protect .................... 6-4
Input Digital Filter ................................................... 6-67
Input Type .................................................... 6-42, A-22
input type ............................................................... 4-11
Integral Time .......................................................... 6-28
Integral Time (Cooling) ..........................4-14, 5-9, 6-29
Integral/Derivative Time Unit ........................ 6-29, 6-66
Integrated Alarm Assignment ....................... 5-24, 6-82
LBA Band ..................................................... 5-29, 6-79
LBA Detection Time ...................................... 5-29, 6-78
LBA Level ..................................................... 5-29, 6-78
LCT Cooling Output Minimum ON Time ................ 6-94
Leakage Current 1 Monitor ........................... 6-11, 6-24
Leakage Current 2 Monitor ........................... 6-12, 6-25
Limit Cycle MV Amplitude ............................. 4-25, 6-67
Loop Burnout Alarm (LBA) .................................... 5-28
Manual Control Level ............................................. 5-34
Manual MV Initial Value ......................................... 6-75
Manual MV Limit Enable ........................................ 6-87
Manual Output Method .......................................... 6-74
Manual Reset Value ............................................... 6-30
Minimum Output ON/OFF Band ............................ 6-88
Monitor/Setting Item 1 to 5 .................................... 6-90
Monitor/Setting Item Display 1 to 5 ........................ 6-38
Move to Advanced Function Setting Level ............. 6-59
Move to Calibration Level ...................................... 6-94
Move to Protect Level .............................................. 6-3
Index-4
Move to Protect Level Time ................................... 6-71
Move to the Protect Level ...................................... 5-20
Moving Average Count ................................... 5-3, 6-68
Multi-SP Set Point Selection .................................... 6-9
MV (Manual MV) .................................................... 6-40
MV at Error ............................................................ 6-33
MV at PV Error ...................................................... 5-49
MV at Stop .................................................... 5-48, 6-32
MV at Stop and Error Addition ............................... 6-73
MV Change Rate Limit ................................. 5-53, 6-35
MV Display ............................................................ 6-69
MV Display Selection .................................... 4-50, 6-91
MV Lower Limit ...................................................... 6-34
MV Monitor (Cooling) ............................................. 6-16
MV Monitor (Heating) ............................................ 6-16
MV Upper Limit ...................................................... 6-34
Number of Multi-SP Points ..................5-11, 5-14, 6-62
Operation/Adjustment Protect ................................. 6-4
Parameter Initialization .......................................... 6-62
Parameter Mask Enable .......................................... 6-6
password ............................................................... 5-20
Password to Move to Protect Level .......................... 6-6
PF Setting ..................................................... 6-38, 6-89
PID ON/OFF .......................................................... 6-44
PID ON/OFF parameter ......................................... 4-22
Position Proportional Dead Band ................. 5-63, 6-35
Process Value Input Shift ........................................ 5-3
Process Value Slope Coefficient ............................. 5-3
Process Value/Set Point 1 ....................................... 6-8
Process Value/Set Point 2 ....................................... 6-8
Program Pattern ........................................... 5-43, 6-46
Program Start ........................................................ 6-12
Proportional Band .................................................. 6-28
Proportional Band (Cooling) ..................4-14, 5-9, 6-29
Protocol Setting ..................................................... 6-95
PV Decimal Point Display ...................................... 6-92
PV Rate of Change Calculation Period ......... 4-35, 6-87
PV Status Display Function ................................... 6-92
PV/MV (Manual MV) .............................................. 6-40
PV/SP Display Selection ......................................... 6-8
PV/SP No. 1 Display Selection ..............4-49, 6-8, 6-91
PV/SP No. 2 Display Selection ..............4-49, 6-8, 6-91
Remote SP Enable ....................................... 5-60, 6-84
Remote SP Input .......................................... 5-60, 6-84
Remote SP Input Shift ........................................... 5-60
Remote SP Input Slope Coefficient .............. 5-60, 6-28
Remote SP Lower Limit ................................ 5-60, 6-85
Remote SP Monitor ...............................5-60, 5-61, 6-9
Remote SP Upper Limit ................................ 5-60, 6-85
RT .......................................................................... 6-76
RT (Robust Tuning) ................................................ 6-76
RUN/STOP ............................................................ 6-13
Scaling Lower Limit ............................................... 6-43
Scaling Upper Limit ............................................... 6-43
Set Point During SP Ramp .................................... 6-10
Set Point Lower Limit ............................................. 5-15
Set Point Upper Limit ............................................. 5-15
Setting Change Protect ........................................... 6-5
Soak Time ...........................................5-42, 5-44, 6-31
E5@C Digital Temperature Controllers User's Manual (H174)