Table of Contents
Advertisement
Command
Configure Serial Port
Set serial port parameters
Read serial port parameters
Configure current port timeout
View current port timeout
Configure global port timeout
View global port timeout
Set UART start point
Read UART start point
KEY:
X6&
Port number:
=
X6*
= Baud rate:
X6(
= Parity odd, Even, None, Mark, Space (Only the first letter is required) – default = None.
X7)
7
8
= Data bits
–
(
X7!
1
2
1
= Stop bits
,
(
X7@
= Port timeout intervals:
X7#
= Start point for UART ports, default is
2002
= Over DTP port). Available port range is
Attempting to remap a port to a number already used by another service returns E13.
LAN/IP Configuration and Setup (see also Set IP/Subnet/Gateway (all at once))
Set date and time
Query date and time
Set DHCP mode
Query DHCP mode
Set IP address
Query IP address
Query hardware MAC address
Set subnet mask
Query subnet mask
Set gateway IP address
Query gateway IP address
Set DNS server IP address
KEY:
X@
= Status:
X7%
= Set Date/Time
X7^
= IP Address (xxx.xxx.xxx.xxx):
X7&
= Hardware ( MAC) address
X7*
= Subnet mask (xxx.xxx.xxx.xxx):
ASCII Command
(Host to Switcher)
EX6& * X6* , X6( , X7) , X7!
}
CP
E X6&
}
CP
E
* X7@
}
0
TC
E
}
0TC
E
* X7@
}
1
TC
E
}
1TC
E X7#
}
MD
E
}
MD
01
= Remote RS‑232 (SIS‑Host Control)
03-04
3
= UART's
(display control port; port
300
600
1200
1800
2400
,
,
,
,
57600
115200
,
; Port 1 is fixed at
8
= default)
= default)
1
65000
(= 10 seconds) –
1999
(Rear panel RS‑232 host port =
1024-65534
E X7%
}
CT
E
}
CT
E X@
}
DH
E
}
DH
E X7^
}
CI
E
}
CI
E
}
CH
EX7*
}
CS
E
}
CS
E X7^
}
CG
E
}
CG
E X7^
}
DI
0
1
= Off
= On
(MM/DD/YY-HH:MM:SS); Example: 06/21/20-10:54:00
Leading zeros in each of the 4 fields are optional in setting values and are expressed in
returned values. Factory Default IP address:
Default Gateway IP addre
(00-05-A6-##-##-##)
Leading zeros in each of the 4 fields are optional in setting values and are expressed in
returned values. Default subnet mask =
Response
(Switcher to Host)
X6* , X6( , X7) ,
X6&
Cpn
•Ccp
X7! ]
X6* , X6( , X7) , X7! ]
* X7@]
Pti0
X7@]
* X7@]
Pti1
X7@]
X7#]
Pmd
X7#]
02
= Unused
2001
4
) and
(Over DTP port; port
3600
4800
7200
9600
,
,
,
,
(default),
9600
.
30
(default is
= 300 seconds = 5 minutes, in 10‑sec. increments)
1999
2001
;
. Ports are disabled by setting to 0 (if applicable).
X7%]
Ipt•
X7%]
X@]
Idh•
X@]
X7^]
Ipi•
X7^]
X7&]
X7*]
Ips•
X7*]
X7^]
Ipg•
X7%]
X7^]
Ipd•
ss: 0.0.0.0,
Default DNS Server UP address:
255.255.0.0
DTP2 R 212 Series • SIS Commands
Additional Description
2002
)
14400
19200
28800
38400
,
,
,
= Display Control RS‑232 port;
MM/DD/YY-HH:MM:SS
Default = 192.168.254.254
Default = 255.255.0.0
Default = 0.0.0.0
Default = 0.0.0.0
192.168.254.254;
0.0.0.0
,
48
Advertisement
Table of Contents
