Extron electronics DTP2 R 212 Series User Manual page 18

DTP2 Endpoint Connected to a DTP2 Endpoint
Extron
DTP HDMI 4K 330 Tx
Transmitter
STATUS
SEND
INPUT
POWER
LINK
CONFIG
OUTPUT
DTP HDMI 330 Tx DTP2 T 211
OFF
Local
Power Supply
OFF
SEND
POWER
Extron
DTP2 T 211
OFF
Transmitter
STATUS
SEND
INPUT
POWER
LINK
CONFIG
OUTPUT
DTP2 T 211
OFF
Figure 5. DTP2 R 212 SA Send Power Toggle Switch Configuration
HDMI output (see figure 3
F
female Type A HDMI port. The EDID information is read from the connected output
device via this port and is written to memory on each input whenever the output device
is connected to this port and powered on.
NOTE: The EDID information is also read and stored whenever power is recycled to
the connected output device or when the output device is replaced.
Audio output — Connect a 5‑pole captive screw connector for balanced or
G
unbalanced analog audio output. This audio output is not amplified and can be
connected to an external amplifier.
Amplified audio output (SA models only) — Connect a 4‑pole captive screw
H
connector for amplified audio output to external speakers.
Display control — Use 3‑pole captive screw connector for bi‑directional RS‑232
I
control of a connected display device.
Remote amplified volume control port (SA models only) — Connect an external
J
audio controller to control volume and mute levels remotely via this 3.5 mm, 3‑pole
captive screw port (see
information and to wire the connection).
Switch for volume control (SA models only) — When using the amplified output
K
connector ( ), flip the switch to the lower position for remote volume control of the
H
amplified output through port
Remote RS-232 port — Connect a serial RS‑232 device via this 3.5 mm, 3‑pole
L
captive screw port for remote control of the DTP2 R 212 (see
RS-232 Control on page 15 to wire the connector).
LAN (Ethernet) port — Use an RJ‑45 cable to connect this jack to a LAN (Ethernet)
M
for control of the device.
No Remote Power
CATx Cable
up to 330' (100 m)
POWER OVER DTP2
12V
2 RS-232 IR
3.0 A MAX 1
HDMI Tx Rx G Tx Rx
Extron
DTP2 R 212 SA
Receiver
Direction of
Remote Power
CATx Cable
up to 330' (100 m)
POWER OVER DTP2
12V
2 RS-232 IR
3.0 A MAX 1
HDMI Tx Rx G Tx Rx
Extron
DTP2 R 212 SA
Receiver
on page 7) — Connect an HDMI display device to this
Remote Control (SA models only)
.
J
DTP2 R 212 Series • Installation
OFF
SEND
POWER
OFF
SIG LINK DTP2 R 212 SA
CLASS 2
4/8 OHM DISPLAY 10V 50mA
L R WIRING
SEND POWER
RS-232
DTP2 IN OFF HDMI Tx Rx G V C
L R
Extron
PS 1242
(4.2 A, 50 Watts)
ON
SEND
POWER
OFF
SIG LINK DTP2 R 212 SA
CLASS 2
4/8 OHM DISPLAY 10V 50mA
L R WIRING
SEND POWER
RS-232
DTP2 IN OFF HDMI L Tx Rx G V C
R
Extron
PS 1242
(4.2 A, 50 Watts)
on page 15 for more
Display and Remote
VOL
RS-232
R
G Tx Rx G LAN
VOL
RS-232
R
G Tx Rx G LAN
10